CERTAIN REPAIR TO TILLING, BOARDING, ROOFING, PANELING, CEILING AND OTHER MISC B/R WORKS FOR OTM ACCN OF OAF UNDER GE 970 EWS

Amount

Demolition of unreinforced cement concrete in ground floors etc and paving n. exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L PCC (1:4:8) type-D2 (using 40mm graded crushed stone aggregate) as in mass concrete and like, complete all as specified and directed.

M&L 60 mm thick glossy finish interlocking tiles of M-30 mix laid over dry sand cushioning, filling of joints with sand & compaction after filling of joints and edges shall be secured with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) complete all as specified and as directed. Note : Sand cushioning shall be measured & paid separately.

Supply and spreading sand filling under floors or interlocking tile or in foundation including watering and consolidation complete all as specified and directed

M&L precast factory made kerb stone of any size and any shape made from cement concrete type B-0 (1:2:4) (using 12.5 mm graded crushed stone aggregate) as in copings, kneelers, apex stones, bed plates, slightly rounded for chamfered angles and throating etc including necessary formwork, complete all as specified and directed.

M&L for 75 mm thick plain cement concrete type D2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and as directed.

M&L chequered cement concrete tiles glossy type 30cm x 30cm x 25mm thick, set, jointed & pointed in neat cement slurry in floors with grey cement & pigment over 15mm thick screed in CM (1:4) including dismantling of previous one old unserviceable all as specified and directed.

M&L for 25mm thick (1:2:4) Type B-1 (using 20 mm graded crushed stone aggregate) as in level course of flooring, complete all as specified and as directed.

M&L non skid/ anti skid ceramic tiles coloured pattern as required of not less than 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over15mm thick screed bed in CM (1:6) compete all as specified and directed including dismantling old tiles.

M&L non skid ceramic tiles coloured pattern as required of not less than 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over15mm thick screed bed in CM (1:6) compete all as specified and directed including dismantling old tiles.

M&L non skid ceramic tiles coloured pattern as required of not less than 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed in CM (1:6) compete all as specified and directed including dismantling old tiles.

Description all as per item No.09 above but in skirting over with and including 10mm thick backing coat in CM 1:4, complete all as specified and directed.

Description all as per item No.10 above but in skirting over with and including 10mm thick backing coat in CM 1:4, complete all as specified and directed.

Description all as per item No.11 above but in skirting over with and including 10mm thick backing coat in CM 1:4, complete all as specified and directed.

M&L vitrified ceramic tiles coloured pattern as required 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matches laid over 15mm thick screed bed in CM 1:6 compete all as specified and directed including dismantling old tiles.

Description all as per item No. 15 above but on skirting over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L glazed ceramic coloured, designer & pattern (dark & light shade combination) tiles in 350x250x7 or 450x350x7 or 450 x 300 x 7-8 mm thick on vertical surfaces such as dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over with and including 10mm thick backing coat in CM 1:4 complete all as specified and directed including dismantling old tiles.

Dismantling structural steel work including doors, gates but excluding framed trusses etc.. complete all as specified and directed.

S&f in repair Roof trusses (framed), trussed, purlins, rafter, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar roof coverings complete all as specified and directed.

Preparing new zinc (or galvanised) and steel surfaces to receive painting, by coating with mordant solution including washing and cleaning, etc. iron surfaces as in roofings exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, all as specified.

S&f for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&f for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws as in ridge,eaves boards, hips, velly gutter drip and straight flushing of reuired machine moulded shape and size complete all as specified and directed.

Anodized aluminium snap grid frame work for false ceiling, size of grid 605 mm x 605 mm, runners of size 15 x 32 mm with hangers of 6 mm dia GI (upto 1200mm length) adjusting level, fixed to roof by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long including 6mm thick non asbestos fibre cement building board of size 610 x 610 x 6mm inserted to GI/ Aluminium frame work with screws, including taking down existing ceiling board & grid work etc of any type/ pattern etc complete all as specified and as directed.

M&L for 5mm thick plain of required texture and coloured PVC sheet in strips and channel feather at the edges for fixing on solid PVC wall lining insulated PVC wall lining and partition inclusive of solvent cement and fixing at site including necessary framing and beading and including dismantling old wall and ceiling boards of any description, complete all as specified and as directed.

Taking down shutter of any description exc. 1 Sqm but n. exc. 2 Sqm each complete all as specified and directed.

Taking down chowkhats or frames not exc 1.5 sqm each (without taking off shutter from the frame) complete all as specified and directed.

S & F powder coated aluminum door with the following specification and making good the adjacent surfaces complete all as specified and as directed:- (a) Cross section of chowkhat frame 101.60x44.45x2mm thick. (b) Cross section of hanging and meeting style 83x44x2mm thick. (c) Top rail of cross section 114x44x2mm thick. (d) Bottom rail of cross section 114x44x2mm thick. (e) Locking rail (middle rail ) of cross section 83x44x2mm thick. (f) 4mm thick tinted glass. (g) Aluminum handle misc type -02 Nos per shutter ( inside & out side). (h) Aluminum door stopper heavy duty-01 Nos per shutter. (i) Aluminum tower bolt 200mm long-01 Nos per shutter (inside). (j) Lock with key superior quality make and type as approved by GE openable both from inside & out side -01 No per shutter.

Hacking out old broken glass pane (any thickness , size, quality or description) from steel frame glazed with putty or fixed with beads, complete all as specified and directed.

M&L for 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane complete all as specified and directed.

S&f PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

S&f factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement shown in SSR Part – II 2004 complete all as specified and directed.

S&f 75 mm size butt hinges medium weight, cold rolled mild steel complete all as specified and directed.

S&f aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete all as specified and directed.

S&f 150 mm size aluminium handles cast type, anodised ISI marked complete all as specified and directed.

S&f in repairs 150mm length floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor complete all as specified and as directed.

S&f 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed.

S&f in repairs double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box , main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty complete all as specified and directed. .

Notes :- An amount of Rs. 62,560.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/s Bashir Enterprises (BID ID -3203023)

M/S Manzoor and Co (BID ID -3202332)

M/S maqsood enterprises (BID ID -3196865)

M/S TARIQ AHMAD SHEIKH (BID ID -3202138)

M/S BHAT TRADERS (BID ID -3203058)

M/S ADIL CONSTRUCTIONS (BID ID -3197431)

M/S RATHER CONSTRUCTION CO (BID ID -3196752)

M/S JAN BUILDERS (BID ID -3203243)

M/S B A Traders (BID ID -3197315)

M/S GHULAM HASSAN KUCHAY (BID ID -3197217)

M/S LATIF AHMAD BABA CONSTRUCTION (BID ID -3197399)