Balance civil, Mechanical works, Plumbing and Sanitary works for Construction of 28 Nos. Govt. Estate Flats (2 BHK, G plus 6 single block) at Ahata Amar Singh Panjthirthi Jammu.

Amount

Earth work in excavation by manual means in foundation trenches, drains, pipes and cables etc. (not exceeding 1.5mtr in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift upto 1.5mtr including getting out excavated soil and disposal of surplus soil as directed, within a lead of 50 mtr. All kinds of soils

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level:- (Including cost / Carriage of material by Mechanical transport)

1:4:8 (1 cement: 4 coarse sand :8 graded stone aggregate 20 mm nominal size) :- CRUSHED

1:2:4 (1 cement: 2 coarse sand :4 graded stone aggregate 20 mm nominal size):- CRUSHED

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering; at all floor levels complete All work above plinth level upto floor five level:- (Including cost / Carriage of material by Mechanical transport)

1:4:8 (1 cement: 4 coarse sand :8 graded brick aggregate 40 mm nominal size):-

Extra for Plain Cement Concrete work in superstructure above floor five level for each four floor or part thereof

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering. shuttering, finishing and reinforcement:- 1:1.5:3 (1 cement: 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size):- CRUSHED (Including cost / Carriage of material by Mechanical transport)

All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in- charge. Note: - Cement in this item is @ 410 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately( crushed stone aggregate). (Including cost / Carriage of material by Mechanical transport)

All works above plinth level upto floor V level

Extra for R.C.C./B.M.C./R.M.C. work above floor V level for each four floors or part thereof.

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge (Granite work). (Including cost / Carriage of material by Mechanical transport)

Centering and shuttering including strutting, propping etc. and removal of form work for:-

Foundations: footings, bases of columns etc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts

Walls any thickness including attached pilasters, buttresses, plinth and string courses etc

Lintels, beams, plinth beams, girders,bressumers and centilevers.

Suspended floors, roofs, landings, balconies and access platform.

Edges of slabs and breaks in floors and walls. Under 20 cm wide

Stairs, (excluding landings) except spiral staircases.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-mechanically treated bars of grade Fe-500D or more (Including cost / Carriage of material by Mechanical transport)

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth including curing in:- Cement mortar 1:6 ( 1 cement : 6 coarse sand); (Including cost / Carriage of material by Mechanical transport)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Extra for brick work in superstructure above floor V level for each four floors or part thereof by mechanical means:

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand); (Including cost / Carriage of material by Mechanical transport)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

Extra for half Brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Extra for providing and placing in position 2 Nos. 8 mm dia. M.S. bars at every third course of half brick masonry.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Providing and fixing of M.S. cover with frame both I.S.I. marked heavy duty for Manholes in Sump/ Septic tanks 560x560 mm size ( the weight of the cover to be not less than 108 Kg); also includes priming coat over them all complete

15mm Cement plaster on the rough side of single or half brick walls of mix: 1 : 6 ( 1 cement : 6 fine sand) on interior walls ,all complete including making of groves and scaffolding, etc. at all floor levels complete (Including cost / Carriage of material by Mechanical transport)

20mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) ,in two coats on exterior walls, all complete including making of groves and scaffolding etc., all floor levels complete (Including cost / Carriage of material by Mechanical transport)

Extra for Plastering exterior walls of the height more than 10m from Ground Level for everyadditional height of 3m or part thereof

Providing and making for plaster drip course to R.C.C. projections(Chajjas) ,all floor levels complete (Including cost / Carriage of material by Mechanical transport)

Providing and laying of vitrified floor tiles (double charged) in different sizes (thickness to be specified by the manufacturer) (Anti-skid) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete SOMANY/ KAJARIA or equivalent only make; at all floor levels complete:- size of tile 60cmx60cm (Including cost / Carriage of material by Mechanical transport)

Providing and fixing Ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufacturers) (Anti-skid) of 1st quality conforming to IS: 13755 of SOMANY/ KAJARIA or equivalent only make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4coarse sand) including pointing the joints with white cement and matching pigment etc., complete at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like SOMANY/KAJARIA only make in all colour, shades except begundy,bottle green, black of any size as approved by Eningeerin-Charge in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarsesand) and jointing wtih grey cement slurry@ 3.3 kg persqm including pointing in white cement mixed withpigment of matching shade complete, at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour or shade:-Polished Granite stone slab jet Black, Cherry Red, Eliten Brown, Cat Eye or equivalent. (Area of slab over 0.5 sqm) 18 mm thick (Including cost / Carriage of material by Mechanical transport) (a) Kitchen

Extra for providing opening of required size and shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble I stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete. (Including cost / Carriage of material by Mechanical transport)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings I wooden frames with rawl plugs screws etc.

Providing and fixing of glass panes with existing wooden fillets: Glass panes weighing 13.75 kg I sqm ( 5.5 mm thick) of make Saint Gobin or Modi float or equivalent ISI marked; all complete

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works all complete.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture of Birla/JK white only over the plastered wall surface to prepare the surface even and smooth complete.( Inner walls and ceilings) at all floor levels complete including scafolding:- (Including cost / Carriage of material by Mechanical transport)

Distempering with oil bound washable distemper of approved brand and manufacture Asian / Nerolac / Berger / Dulux paints only to give an even shade New work (two or more coats) over and including priming coat with cement primer; at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport) with scafolding complete.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28litre/10sqm over and including base coat of waterproofing cement paint applied@ 2.20kg/10sqm); and also providing weather shield protection coat over the textured surfaces, all complete of approved brand and manufacture Asian/Nerolac/Berger/Dulux paints only all complete including scaffolding etc.; at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and Applying priming coat: with ready mixed pink or grey primer of approved brand and manufacture Asian/Nerolac/Berger/Dulux paints only on wood work (hard and soft wood) one or more coats (Including cost / Carriage of material by Mechanical transport)

Painting with ready mixed synthetic enamel paint of approved brand and manufacture Asian / Nerolac / Berger / Dulux paints only in all shades to give an even shade New steel/wood work (two or more coats) (Including cost / Carriage of material by Mechanical transport)

Providing and laying water proofing treatment on sunkan portion of Toilets by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement -,. compound@ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (Including cost / Carriage of material by Mechanical transport) (c) third layer of 1.5 mm thickness consisting of slurry ofcement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg./sqm. and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

Providing and laying integral cement based water proofing treatment including prepration of surfaces as required for treatment of roofs, balconies, terracies etc consisting of following operations(Including cost / Carriage of material by Mechanical transport) a) applying a slurry coat of neat cement using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement: 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. d) finishing the surface with 20mm thick jointless cement mortar of mix 1:4(1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved byEngineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finially finishing the surface with trowel with neat cement slurrv and making pattern of 300x300mm/sq 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete (Including cost / Carriage of material by Mechanical transport)

Brick edging 7cm wide 11.4cm deep to plinth protection with common burnt clay (nonmodular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 Cement : 4 fine sand) and curing complete (Including cost / Carriage of material by Mechanical transport)

Providing and fixing strips in joints of terrazzo/ cement concrete floors. Glass strips 40 mm wide and 6 mm thick (Including cost / Carriage of material by Mechanical transport)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase. (Including cost / Carriage of material by Mechanical transport)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class teak wood

Providing and fixing 35 mm thick glazed shutters for Windows, Doors, ventilators and clerestory windows using 10 kg/sqm (4mm thick) float glass panes with lSI marked Stainless steel Butt hinges (heavy weight) of required size with necessary screws (float glass should be of make Saint Gobain or Modi float or equivalent) :- Second Class Deodar Wood (Including cost / Carriage of material by Mechanical transport)

Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average width for aperture 1.4 mm in both direction with wire of dia. 0.63 mm for doors, windows, ventilators and clerestory windows with lSI marked Stainless Steel Butt hinges (heavy weight) of required size with necessary screws :- Second Class Deodar Wood (Including cost / Carriage of material by Mechanical transport)

Providing and fixing & fabrication of 35 mm thick Laminated Flush Door Shutters made up of 32 mm thick solid core flush door (Gurjan core) having 1.5 mm thick Laminate/Sunmica Matt finish on both faces & 35x6 mm thick Teak wood lipping/margin on alround of Flush door and also including fixing of door shutters with I.S.I. marked stainless steel butt hinges 100x60x2.5 mm heavy weight & necessary S.S. screws; all complete:- (32mm thick solid core flush door should of make Sonear/Archid/Green/Century or equivalent only & 1.5 mm thick Sunmica Matt finish should of make Merino/Green/Archid/Century or equivalent only & Flush door should be water proof BWP I.S. 710 grade, borer free, anti-termite, fire retardent etc.) fabrication be done at site (Including cost / Carriage of material by Mechanical transport)

Providing and fixing & fabrication of 40 mm thick Teak Veneered Flush Door Shutters made up of 32 mm thick solid core flush door (Gurjan core) having 4 mm thick Teak veneer on both faces & 40x6 mm thick Teak wood lipping/margin on alround of Flush door and also including fixing of door shutters with I.S.I. marked stainless steel butt hinges 100x60x2.5 mm heavy weight & necessary S.S. screws; all complete:- (32mm thick solid core flush door should of make Sonear/Archid/Green/Century or equivalent only & 4mm thick Teak veneer should of make Green/Archid/Century or equivalent only & Flush door should be water proof BWP I.S. 710 grade, borer free & anti-termite, fire retardent etc.) fabrication be done at site (Including cost / Carriage of material by Mechanical transport)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)

For fixed portion/ Frames

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. Pre-laminated particle board with decorative lamination on both sides (Door shutter)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin- charge. (Cost of aluminum snap beading shall be paid in basic item.) With float glass panes of 5.5 mm thickness (weight not less than 13.50 kg / sqm).

Providing and fixing Anodized aluminum grill (Anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved Anodized aluminum standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment)

Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Including cost / Carriage of material by Mechanical transport)

Providing and fixing aluminium sliding door bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

300 mm long

200 mm long

125 mm long

Providing and fixing aluminium pull bolt lock anodised lSI marked (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws bolt nuts and washers etc. complete .

Providing and fixing aluminium hanging floor door stopper lSI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper

Providing and fixing aluminium Eye Hook Latch lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or eyed to required colour or shade with necessary screws etc. complete :

Providing and fixing of Rubber Door back stopper Lever type door mounted with necessary screws/nuts etc. complete: 75 mm long

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Rebaring of Tor-steel bars of required dia. by way of drilling holes of required dia. upto the depth of (10-15) times of dia. of hole with hammer drilling machine or core cutting machine and then cleaning of hole by way of removal of dirt, dust and loose particles and then filling of chemical of HILTI make Hy-150/ Hy- 200/ Re-500 as recommended upto 2/3 depth of hole and then fixing of bars by rotating in the hole upto the drilled depth:-

8mm dia. of bars

10mm dia. of bars

12mm dia. of bars

16mm dia. of bars

20mm dia. of bars

25mm dia. of bars

Supply and laying of RBM Material with a lead of 10 km (all complete job)

PLUMBING & SANITARY

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied W.C. pan with lSI marked white solid plastic seat and lid of make Hindware/Cera/Jaquar only:- (All Carriages)

Providing and fixing wash basin with C. I./M.S. brackets,15mm C.P. centre hole basin mixture, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps of make Hindware/Cera/Jaquar only:- (All Carriages)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings of make Hindware/Cera/Jaquar only:- (With Carriages)

Providing and fixing Salem Stainless Steel A lSI 304 (18/8) kitchen sink including waste coupling as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fitting sand brackets, cutting and making good the walls wherever required of make Kaff/Neelkanth/Hindware or equivalent all complete :-510x1040mm bowl depth 250mm (With Carriages)

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete. Flexible pipe 40 mm dia (With Carriages)

Providing and fixing 100 mm CP grating (hole or without hole) for gully, floor or Nahani trap.ISI marked All complete of make hindware/Cera/Jaquar only:- (With Carriages)

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete ISI marked of make Saint Gobin or Modi float or equivalnet brand as approved by Engineer incharge at site:- (With Carriages)

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C. P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete of make hindware/Cera/Jaquar only:-

Providing and fixing unplasticised - Rigid PVC PIPES conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap of thermal expansion;with necessary stays / clamps with fasteners having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport)

50 mm dia

75 mm dia

110 mm dia

160 mm dia

200 mm dia

250 mm dia

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport)

PVC PLAIN BEND (of required degree):-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC DOOR BEND( of required degree):-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC PLAIN TEE:-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC DOOR TEE:-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC REDUCER PLAIN TEE:-

110 mm x 75 mm

160 mm x 110 mm

200 mm x 160 mm

PVC REDUCER DOOR TEE:-

110 mm x 75 mm

160 mm x 110 mm

200 mm x 160 mm

PVC OFFSETS:-

50 mm PVC off sets

75 mm PVC off sets

110 mm PVC off sets

160 mm PVC off sets

200 mm PVC off sets

PVC COUPLER/COLLAR:-

50 mm dia

75mm dia

110mm dia

160 mm dia

200 mm dia

PVC VENT COWL:-

75mm dia

110mm dia

160 mm dia

PVC FLOOR/NAHANI TRAP:-

110 mm x 75 mm

110 mm x 100 mm

PVC P/Q/S TRAP:-

100 mm dia.

Providing and fixing square- mouth S.W. gully trap grade 'A' complete with C. I. grating brick masonry chamber with bricks of class designation 75 in cement mortar 1:5 ( 1 cement : 5 fine sand) and water tight C. I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.:- 180 x 150 mm size P type With F.P.S. bricks (Including cost / Carriage of material by Mechanical transport)

Providing and fixing Soap dish (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing towel ring (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing towel rail 600mm long (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 of make hindware/Cera/Jaquar only:-. (a)15 mm nominal bore (With all Carriages)

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms of make hindware/Cera/Jaquar only: (With all Carriages) a) 15 mm nominal bore

Providing and fixing C.P.Brass stop cock (concealed) of standard design and of approved make conforming to IS : 8931 of make hindware/Cera/Jaquar only: (With all Carriages) a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin/wall mixer and geysers points of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge (With all Carriages)

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore (With all Carriages)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge all complete of make hindware/Cera/Jaquar only:-. (With all Carriages)

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Providing and fixing C.P. Brass Central Hole BASIN MIXER without Popup Waste System with 450mm Long Braided Hoses with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (With all Carriages) (a) 15 mm nominal bore

Providing and fixing C.P. Brass SINK MIXER with Swinging Spout (Wall Mounted Model) With Connecting Legs & Wall Flanges with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (With all Carriages) (a) 15 mm nominal bore

Providing and fixing of C.P. Brass WALL MIXER with provision for Overhead Shower with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (Incl. all Carriages) (a) 15 mm nominal bore

Providing and fixing of C.P. Brass OVERHEAD SHOWER 100mm dia. Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (Incl. all Carriages) (a) 15 mm nominal bore

Providing and fixing of C.P. Brass SHOWER ARM Casted 190mm Long Light Body Round Shape For Wall Mounted Showers with Flange with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (Incl. all Carriages) (a) 15 mm nominal bore

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc.(internal work) of make Jindal/Surya Prakash of medium class or as approved by site incharge (INTERNAL WORK-Exposed on wall) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc. (Incl. all carriages)

15 mm dia. nominal bore (medium)

20 mm dia. nominal bore (medium)

25 mm dia. nominal bore (medium)

32 mm dia. nominal bore (medium)

40 mm dia. nominal bore (medium)

50 mm dia. nominal bore (medium)

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, Concealed pipe including painting with anti-corrosive bitumastic paint(two coats) over a ready mixed priming coat , cutting chases and making good the wall , all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make Jindal/Surya Prakash of medium class or as approved by site incharge (Incl. all carriages)

15 mm dia. nominal bore (medium)

20 mm dia. nominal bore (medium)

Providing and fixing G.l. pipes complete with G.l. fittings including trenching and refilling etc. (EXTERNAL WORK) of make Jindal/Surya Prakash of medium class or as approved by site incharge all complete including testing of pipes and fittings and joints for leakage with pressure pump etc. (Incl. all carriages)

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Making connection of G.l. distribution branch with G.l. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make UNIK or NEW or equivalent as approved by site incharge (Incl. all carriages)

25 to 40 mm nominal bore

50 to 80 mm nominal bore

Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make UNIK or NEW or equivalent as approved by site incharge (Incl. all carriages)

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and filling sand of coarser grade alround the G. I. pipes in external work. (Including cost / Carriage of material by Mechanical transport)

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license] (incl. cost / carriage of material upto roof top).

Providing and fixing G.I.TANK NIPPLE of suitable dia. of make UNIK or NEW or equivalent ISI marked as approved by engineer incharge at site all complete including testing of fittings and joints for leakage etc.:- (incl. all carriages)

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Providing & fixing BRASS BALL VALVE of approved quality conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing BRASS FLOAT BALL VALVE; High or low pressure with plastic floats:- of approved quality conforming to IS : 8931 of make UNIK or DRP or approved by engineer incharge at site (incl. all carriages)

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing Gun metal gate valve with C.l. wheel of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing Gun metal non-return valve of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

25 mm nominal bore

Horizontal

Vertical

32 mm nominal bore

Horizontal

Vertical

40 mm nominal bore

Horizontal

Vertical

50 mm nominal bore

Horizontal

Vertical

Providing and fixing Brass Foot valve with strainer/filter of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing of stainless steel Rainwater Khurra JALI to be placed at roof and mumty levels of make CHILLY or CAMRY or equivalent all complete:- square or circular in shape of dia/size:- (incl. all carriages)

Providing & Installation of 3 H.P. three phase water pump of make Crompton with all fittings, connecting inlet & outlet, fixtures, electrical connection and starter all complete:- (incl. all carriages)

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks (Including cost / Carriage of material by Mechanical transport)

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. (Including cost / Carriage of material by Mechanical transport)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design (Including cost / Carriage of material by Mechanical transport)

Inside size 90x80 cm and 45 cm deep including C.l. cover with frame (light duty) 455x610 mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With F.P.S. bricks with class designation 75 & with Crushed stone aggregate

Disposal of surplus excavated Earth work material by mechanical transport beyond 50 mtr and within average distance of 10 Kms

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete. (Including cost / Carriage of material by Mechanical transport)

Providing and fixing of structural glazing using aluminium section 50mmx50mmx2mm with 50 micron powder coated confirming to IS 733 & IS1285 with 50mmx50mmx6mm long M/S brackets expansion fasteners 10mmx100mm as required & 5mm thick reflective toughened glass of make Saint Gobain/ Gold plus or equivalent with colour shade with 6mm double type adhesive tape & structure silicon dow corning 995/786/GE SSG-400 only (coated mirror side to be inside in the building).

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti termite treatment. (including the cost of chemical emulsion):

Along the external wall below concrete or masonry apron using chemical emulsion (Chloropyriphos / Lindane E.C. 20% with 1% concentration) @ 2.25 litres/ linear meter including drilling & plugging holes etc.

Treatment of soil under existing floors using chemical emulsion (Chlorophriphos/Lindane E.C. 20% with 1% concentration) @ one litre per hole, 300mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floor:

Supplying and filling in plinth with fine sand under floors including, watering,ramming, consolidating and dressing complete.

Extra for additional height in centering , shuttering where ever required with adequate bracing, propping extra including cost of de-shutering & de- centering at all levels over aheaight 3.5 mtr, for every additional height of 1 mtr or part thereof (plan area to be measure) For Pergola beams.

Mechanical works

Supply, Installation, Testing and Commissioning of Fire hydrant system

SITC of underground M.S Pipes (B class) including excavation,cutting, screwing, welding etc. and providing all fittings e.g flanges, bends, tees, elbows reducers, clamps, hinges etc. Underground pipes shall be wrapped & coated by providing twin coating of Bitumen wrapping with first coating bitumen coating Wrapping with bitumen Hessian cloth & finishing with Bitumen paint and re-filling the trenches etc of following sizes:

a) 150 mm dia

Same as above but for over ground M.S Pipes (B class) including cutting holes & chases in bricks or RCC wall/slab & Making good the same. Painting with one coat of primer and two coats of synthetic enamel of approved shade of following sizes:

a) 200 mm dia

c) 100 mm dia

d) 80 mm dia

e) 25 mm dia

SITC of single headed oblique pattern hydrant Landing valve with 80mm dia flanged inlet and 63mm dia Instantaneous type female outlet complete with cap and all Accessories ISI marked.

Supply of non-percolated flexible hose RRL 63mm dia x 15 mtr long complete with instantaneous type 63mm dia male and female ISI marked coupling and Riverted to hose pipe with riverts and copper wire.& ISI marked

Supply & installation of gunmetal 63mm dia short branch pipe with 20mm dia nozzle , ISI marked.

SITC of First aid hose reel wall mounting swinging type complete with drum & brackets, 25 mm dia ball valve & 20 mm dia 30 mtr long high pressure pad hose with shut off nozzle complete as req.

SITC of cast iron double flanged ISI marked Butterfly valve complete with rubber insertion, nuts, bolts, washers etc. of following sizes:

a) 150 mm dia

b) 100 mm dia

c) 80 mm dia

SITC of following accessories:

a) 25mm dia spring loaded air release valve with isolation cork.

b) Pressure Guage

c) Pressure Switch

d) 25 mm dia gate valve

SITC of cast iron double flanged ISI marked NRV complete with rubber insertion, nuts, bolts, washers etc. of following sizes:

a) 150 mm dia

b) 100 mm dia

c) 80 mm dia

SITC of gunmetal Fire Brigade connection with collecting head 63mm,4 way instantaneous type male couplings with flanged outlet complete with blank caps nuts, bolts & rubber insertions, conforming IS:904-1983

Supplying & laying of 4 core 10 sqmm Aluminum cable from motor to electrical panel for automation of the system.

Supplying & lying of 3.5 core 150 sqmm Aluminum cable frommotor to electrical panel for automation of the system.

SITC of Air vessel 250mm dia and 1.5 mtr high withdished top, made of 6mm thick MS pipe complete with 25 NB dia gun metal air release valve, 20mm dia stop valve,25Nb gun metal pressure release valve,49NB drain valve , pressure guage & all accessories as req and painted.

Earthing with G.I earth plate (600 x 600x 6) mm thick including accessories & providing masonry enclosure with M.S cover plate & Watering pipe of 40 mm dia etc. as required with charcoal and Salt including excavation and back filling complete as required.

SITC of diesal Engine driven main fire Pump suitable for automatic operation with broze impeller capacity 2280LPM with 56mtr head with Diesel Engine of suitable HP,12V/24V starting equipment water cooled with 125 mm suction and 100 mm delivery ; with Base frame, coupling, battery fuel tank, AVM pads etc. complete as required. The pump shall be provided with mechanical seal complete as req.

SITC of horizontally centrifugal end suction pump complete for delivery 2280 ltr/ min against a total head of 56mtrs. With 50 HP three phase motor with speed of 2900 rpm with bronze impeller and coupling, base frame and AVM pads complete as required. The pump shall be provided with mechanical seal.

SITC of horizontally mounted centrifugal pump complete for delivery 180 ltr/ min against a total head of 56mtrs. With 10 HP three phase motor with speed of 2900 rpm with bronze impeller and coupling, base frame and AVM pads complete as required. The pump shall be provided with mechanical seal.

Supply & installation of weather proof hose cabinetsfabricated from 18 swg MS sheet/section with full front glass door and suitable to accommodate 2 nos 15 mtr long hoses and 1 no branch pipes as req.

P/f 25 mm x 5 mm G.I strip from earth electrode, on surface or in recess for earth connections as required.

SITC of gunmetal suction coupling for Fire Brigade drawal of water from fire tank of 100 mm dia.

Design, Manufacture, Supply ,Installation, Testing and commissioning of one no 6 passenger machine room less (MRL) elevator

CAMC of the lift for a period of one year after the successful completion of warranty period

ADITYA CONSTRUCTIONS

M/S MAGOTRA ENGINEERS and CONTRACTOR

KARNAIL SINGH