COMPREHENSIVE REPAIR OF BLDGS UNDER AOR OF AGE BR DETT II OF GE 862 EWS

Amount

Taking down cement plaster on brick or stone walls including racking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work/Stone surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work/Stone surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick in cm 1:3 over ceilings etc finished surface even and smooth with out using extra cement, complete all as specified and directed.

All as per item No 4 here-in-before but 10mm thick in CM 1:3 on concrete surfaces such as chajjas, roof facias, fins etc.

Preparation of newly plastered wall surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

Preparation of newly plastered ceiling surfaces and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of Newly plastered surface of walls and applying two coats of oil bound distemper, complete all as specified and directed.

M&L for Preparation of old surface of wall and applying one coat of oil bound distemper , complete all as specified and directed.

M&L for applying one coat of lime white wash on old decorated surfaces of the walls, pillars, cornices etc after preparation of surfaces, complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of exterior weather coat paint in multi colour pattern in three or more colours as approved by GE, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L Cement concrete type B0 (1:2:4) using 12.5mm graded stone aggregate 25 mm thick as in path / sub base to receive tiles etc, complete all as specified and directed.

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

M&L for coloured glazed ceramic tiles on vertical surface of size 450 x 350 x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick cement plaster in CM (1:3), complete all as specfied and directed.

M&L for light shade Vitrified tiles 9-10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, laid over and including 15mm thick screed bed in CM(1:4) in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement to match, complete all as specified and directed.

M&L for Light shade Vitrified tiles 9-10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, laid over and including 10mm thick rendering in CM(1:3) in dado /skirting jointed in neat cement slurry & pointed in white or coloured cement to match, complete all as specified and directed.

Demolition of cement concrete unreinforced in Ground floor & paving n.exc 15cm thickness and removal of debris from site, complete all as specified and directed.

M&L for cement concrete type C-2 1:3:6 (using 40mm graded stone aggregate ) as in subbase, etc. 50mm thick, complete all as specified and directed.

M&L for providing kota sotne slab flooring 18-20 mm thck over and including 20 mm thick screed in Cement morter1:4 and jointed with grey cement slurry mixed with pigment including cutting, rubbing and polishing (mirror finish) , complete all as specified and directed.

M& L for providing Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar over cement plaster(10 mm thick) in cm(1:3) and jointed with grey cement slurry mixed with pigment including cutting, rubbing and polishing, complete all as specified and directed.

S&F rotational moulded polythene water storage tank (Cylindrical vertical withclosed top)hoisted and fixed in position of 500 ltrs capacity fixed with PVC tank nipples, complete all as specified in SSR Part I including dismantling of old existing tank, complete all as specified and directed.

S&F rotational moulded polythene water storage tank (Cylindrical vertical withclosed top)hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples, complete all as specified in SSR Part I including dismantling of old existing tank, complete all as specified and directed.

Cleaning of PVC water tank any capacity(marking date,month and year on water tank with paint as directed by engr-in-charge) and including dismantling and refixing at same place including repair/ replacement of required fitings (PVC Ball valve with Brass Rod, tank nipple etc, complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description from wooden or steel frames glazed with putty/beads, complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n . exc 0.50 sqm in each pane, complete all as specified and directed.

Taking up or down 15mm bore GI tubing and connections including cleaning for re-fixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore GI tubing and connections including cleaning for re-fixing or removal to store, complete all as specified and directed.

S&F medium grade galvanised steel water tubing with all fittings fixed to wall or laid in floors of 15 mm bore, complete all as specified and directed.

S&F medium grade galvanised steel water tubing with all fittings fixed to wall or laid in floors of 20 mm bore, complete all as specified and directed.

S&F in repairs 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F in repairs 75mm PVC (SWR) bends any radius, complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches/wall, complete all as specified and directed.

S & F in repair for 110 mm bore PVC (SWR) bends of any radius with access to door, complete all as specified and directed.

S&F in repairs 75mm PVC (SWR) Junction single,(single T), equal or unequal, complete all as specified and directed.

S&F in repairs 110mm PVC (SWR) Junction single,(single T), equal or unequal, complete all as specified and directed.

S & F in repair for 75 mm bore PVC (SWR) bends of any radius with access to door, complete all as specified and directed.

S & F in repairs Vitreous China Ware Wash hand basin white (padestal pattern), flat back, size 550x400mm size including cutting for and pinning ends of brackets or erecting stand, complete all as specified and directed.

S&F in repairs vitreous china,coloured, counter top wash hand basin, oval type, size 550mm including cutting for and pinning in, but including waste pipe, complete all as specified and directed.

S&F in repairs vitreous china water closet Padestal pattern( white ) including fixing bolts, flushing cistern and flush pipe, seat covers, complete all as specified and directed.

S&F in repair for viterous china water closet pedestal pattern in one piece type of dimention 73cmX36cm74cm including seat cover and gaset, floor mounted, 'P' or 'S' trap, flushing kit, CP jet with PVC pipe of superior quality and all necessary fixing arrangements, complete all as specified and as directed.

S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe, complete all as specified and directed.

S&F in repairs plastic sheet covers for water closet, black,closed pattern with flat bottom with mild steel chromium plated or alluminised hinging device, screws, bolts etc, complete all as specified and directed.

S&F in repair for vitreous china urinals, half stall type Aqua Seal Premium quality including flush pipe including PVC waste pipe, speader, grating and outlet, complete all as specified and directed.

M&L in repairs Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (minimum weight 60 gms), complete all as specified and directed.

S & F in repairs, Towel rack 600mm long with lower hangers by replacing the existing towel rail etc, complete all as specified and as directed.

S&F in repairs 10 ltrs capacity (PVC), valve less, syphonic action type, fluhsing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F in repair 15mm CP brass health faucet (hand shower), inlet length1000 mm fixed to angle valve with and including decorative choice flexible pipe, wall hanger etc, complete all as specified and directed.

S&F in repair copper alloy chromium plated jet spray suitable for padestal pattern WCs including decorative choice flexible pipe fixed to iron pipe with and including cover plate, complete all as specified and directed.

S&F in repair for PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S&F in repair PVC waste pipe 600/900mm long suitable for Wash hand basins and urinals including connecting, complete all as specified and directed.

S &F in repairs Swan neck CP brass Pillar Cock , 15mm bore, cast copper alloy, with capstan heads, chromium plated,fancy type, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed.

Supply and fix in repairs of CP brass wall mixers 2 in 1 two for hot and cold water mixing and one for shower rose of 15mm dia screwed down for iron pipe as suitable to existing site, complete all as specified and directed.

S&F in repairs of CP brass WHB mixers for hot and cold water mixing of 15mm dia screwed down for iron pipe as suitable for site, complete all as specified and directed.

S&F in repairs rectangular Glass Self (With SS Bracket) Glass Shelf 300 X 100mm Long, complete all as specified and as directed.

S &F in repairs brass CP shower rose of size 125 mm with swivel joints fixing to steel pipes etc, complete all as specified and as directed.

S&F in repairs concealed type Stop valves, 15 mm bore of pipe, cast copper alloy CP, screwed down, high pre-ssure, with long shank and cup, screwed both ends for iron pipe or for unions and fixed, complete all as specified and as directed.

S&F in repairs 15mm dia bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15mm-90gms/20mm- 125gms), complete all as specified and as directed.

S&F in repairs angle valve (15mm dia), cast copper alloy, fancy type,chromium plated suitable for iron pipe and one end and PVC connector on other, ISI marked, complete all as specified and as directed.

S&F in repairs gun metal globe or gate valve (15mm dia) with iron wheel screwed both ends for iron pipe of 15 mm dia, complete all as specified and as directed.

S&F in repairs gun metal globe or gate valve (20mm dia) with iron wheel screwed both ends for iron pipe of 20 mm dia, complete all as specified and as directed.

S&F in repair CP grating suitable for 75/100 mm bore floor trap and fixed with white cement, complete all as specified and as directed.

S&F in repairs Shelf of PTMT (Minimum weight 300 gm) including chromium plated brass screws and wooden/ plastic cleats, complete all as specified and as directed.

S&F in repairs Towel rail 18mm dia, 600 mm long of made of Stainless steel tubes of min thickness 0.75 mm, decorative type fixed with with & including screws and wooden/plastic cleats, complete all as specified and as directed.

S&F in repairs 32mm dia waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms), complete all as specified and as directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S&F in repair assembled ready to use rectangular stainless steel (Grade 304) kitchen plate rack with 3-4 shelves, enclosed four sides by SS plain sheet, 0.6mm square support pipes, dedicated holes for spoon, pegs etc over all size 600mmx750mmx250mm of standard pattern, complete all as specified and as directed.

S&F in repair for mirror cabinet of plastic body,of size 400mm x 500mm including shelves,mirror of slected quality glass,etc heavy duty, complete of approved make all as directed.

S&F in repair for looking mirror of size 450 x 600mm with plywood backing and aluminium frame, complete all as specified and as directed.

Taking down chowkats or frames with shutter(without taking off shutter from the frame) area not exc. 1.5 sqm each & removing form site incl making good disturbed portion, complete all as specified and as directed.

Taking down chowkhats or frame with shutters without taking of shutters from frames exc 1.5 Sqm but not exc 4.00 sqm each & removing form site incl making good disturbed portion, complete all as specified and as directed.

Taking down Shutters of any description exc 1 sq. m and not exc 2 Sqm. with necessary fittings, complete all as specified and as directed.

S&F in repairs GI mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed.

S&F Sheet glass 5mm thick, ordinary quality and fixed with aluminium & rubber beading in square n exc 0.5 sq. m in each pane including hacking out of old brocken glass, complete all as specified and as directed.

S&F in repair block boards 18/19 mm thick Grade II interior grade commercial type with decorative face veneer on both faces fixed with screws incl 6mm thick teak wood lipping as in cub boards incl builders hardware fittings, complete all as specified and as directed.

M&L in repairs double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and as directed.

M& L in repairs Mild steel 150mm long, ordinary rat tail rod pattern springs including roller and roller plate welded to steel frame, complete all as specified and as directed.

Demolition of brick/stone work built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast cement articles, complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius in CM 1:6, complete all as specified and as directed.

All as per Item No 79 here-in-before but except bricks.

Dismantling AC Sheets/CGI Sheets corrugated / fibre glass reinforced translucent sheet / PVC sheet in roof coverings including ridges, complete all as specified and as directed.

S&F Pre-painted coloured trapezoidal profiled Galvalume / Zincalume sheet with min thickness of 0.50 mm TCT confirming to IS-513 (AZ-150 GSM, AI Zn alloy mettalic coating with 550MPA yield stress as per AS-1397) as in roof covering/cladding to wall, curved roof fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron poyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and as directed.

S&F Pre-painted coloured plain Galvalume / Zincalume sheet with min thickness of 0.50 mm TCT confirming to IS-513 (AZ-150 GSM, AI Zn alloy mettalic coating with 550MPA yield stress as per AS-1397) as in roof ridge colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron poyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self tapping fastener (12-14 x 55 with EPDM seals) complete as specified etc complete all as specified and as directed.

S & F fibre glass (2mm thick) reinforced translucent sheeting fixed with coach screw and washer in roof, wall etc, complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.)/PVC fall ceiling or insulation boards / slabs / blankets, any thikness, including cover fillets, complete all as specified and as directed.

S&F Decorated PVC False ceiling of size 600mmX600mmX5 mm thick, used as a panel insert in a frame work made using anodized aluminum T-section of size 25mmX25mm in square pattern of grid size 600mmX600mm. The aluminum frame work is supported from the ceiling with the help of J Hook and 4 mm GI wire of required size to maintain the proper levels etc. The aluminum frame work is supported on side wall with the use of aluminum L section of size 25mmX25mm angle, complete all as specified and as directed.

M&L Providing & fixing of 4mm thick designer ceiling board (Make : Everest/Ramco/Everest) in ceiling fixed with screw as per manufactures instructions, laid on hot dipped galvanized iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick galvanized steel sheet & of size 24x32x300mm and spaced at 12mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 3 mm dia to be fixed by approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200 long cross tee with (double stitching) to be inter locked between main runners at 600mm centre to from 1200x600mm modules cross tee longer than 600mm modules to be formed by fitting 600mm long cross tee, tee perimeter wall angle shall be of 0.45mm thick galvanized steel of size 19x19mm and 300mm long of white colour, complete all as specified and as directed.

S & F in repair plain ACP board 12 mm thick, fixed in aluminium door or similar works joinery including cutting, packing, finishing, complete all as specified and directed.

Dismantling structural steel work including welded fabricks frames, gates, framed truss etc, complete all as specified and as directed.

M&L for rolled sections as in main and cross beams/columns, hip and jack rafters, truss, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates.(Fe-410 W Gde E-250 Quality A), complete all as specified and as directed.

S&F in repair stainless steel tubular railing SS 304 grade fixing by cutting through the existing wall and attaching the faseners of railing to the existing reinforcement by welding, vertical members, including making good the distribuded portion to match with existing specifications, complete all as specified and as directed.

M&L in repair for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over 20 mm thick CM (1:4) incl rounding the edges, cutting polishing complete all as specifeid and directed by Engr-in-Charge.

S&Fin repair for 15 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

M & L for repair in Wood/aluminium door bottom sealing strip guard with double sided insulation for doors, which are equally able to keep wind, dust and sound or poluted air out side of door (i.e. Anti Lizard strip) fixed to aluminium or pannel door, complete all as specified and as directed.

S&F in repair Aluminium anodized grills 7-8mm dia decorative type 75mm mesh size, complete all as specified and as directed.

S&F standard aluminium powder coated section (minimum thickness of powder coating shall be 50 micron and colour as in frame & shutters for Door/Windows / Ventilators, fixed/openable/sliding or any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass and stainless steel wirecloth, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and as directed. Note : (i) Weight of Aluminium sections as per actual or as per IS or as per Manufacturer which over is less, shall only be considered for payment. (ii) Cost of all the items/ accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and wirecloth shall be measured and paid separately under respective items. (iii) The accessories (Aluminium mongries etc) required to be provided for window, vents and doors as per directions of Engineer-in-chargeshall be provided but weight for the same shall not be considered and no extra cost will be paid.

S&F in repair standard anodized aluminium section as in frame for partition, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass and stainless steel wirecloth and particle board, etc complete all as specified and directed. Note: (i) Weight of Aluminium sections as per actual or as per IS or as per Manufacturer which over is less, shall only be considered for payment. (ii) Cost of all the items/ accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and particle board shall be measured and paid separately under respective items. (iii) The accessories required to be provided for partition as per directions of Engineer-in-chargeshall be provided but weight for the same shall not be considered and no extra cost will be paid.

Taking down aluminium/Toughned glass shutters size n exc 2 sqm each and refixing in the same opening after carry out any repair required, complete all as specified and directed. Note (a) Cost of parts replaced shall be included in the rate of above item. (b) the new door will be fixed within 3 days after removal/taking down.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi- chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by GE. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profiledimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Factory made MS tubular Box type window of MS rolled steel section conforming to IS-1038 and shall be ISI marked manufactured by ISI approved manufacturer, openable frames shall be fabricated of sections as approved by GE, corner welded to form a solid fused welded joint handles shall be of z section welded with openable frame box steel section(Consisting of both shutter glazed shutter and gauge shutter complete) used in outer frame shutter frame and central frame shall be ERW section of 16 gauge with fixing lugs to be fixed as per provision of IS-1038 except that top lugs shall not be provided , all shutters of windows shall be provided with 4 Nos friction free hinges, 2 Nos 75 mm tower bolts to each leaf of window one at top and one at bottom welded on 3 mm thick steel sheet piece of suitable size which shall be in turn welded to z section f steel window to provide suitable arrangement of using tower bolt and 1 nos bow handle in each shutter. Glazed shutter and , gauged shutter of window , mild steel casement stays 300 mm with hinged joint and two plates with studs complete all as specified with all fittings and fixtures without glazing bars, 3mm sheet glass in glazed shutter and, GI wire mesh,of 0.56 nominal dia and average width of aperature 1.18 mm in gauged shutter, etc complete all as specified and as directed.

M & L for factory made 100% Solid WPC Door Frame 90 mm x 45 mm Single Rebated made from Wood Polymer Composite ( Single Extruded Process ) material comparising of virgin PVC polymer of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and Natural Fibers ( Wood Powder/ Rice Husk/ Wheat Husk ) and Non toxic additives fabricated with meter Joints after applying PVC solvent Cement & screwed with full body treaded star headed screws having minimum frame density of 780 kg/ cbm & manufactured by " RAJSHRI " an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of ( Min. 990 N ), Minimum Compressive Strength of 58 N/mm2 , Modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof , water / Moisture Proof & Fire retardant & Fixed in position with SS Dash Fasteners / Hold Fast of required dia and lenght, complete all as per specifications drawings and as directed. Note: Material test certificate and authentication shall be compulsory provided by the manufacturing company.

M & L for Factory Made 30mm thick 100% Solid WPC Laminated Moulded Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by "RAJSHRI" an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company, complete all as specified and directed.

M & L for factory made 100% Solid WPC Door Frame 125mm x 65 mm double Rebated made from Wood Polymer Composite ( Single Extruded Process ) material comparising of virgin PVC polymer of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and Natural Fibers ( Wood Powder/ Rice Husk/ Wheat Husk ) and Non toxic additives fabricated with meter Joints after applying PVC solvent Cement & screwed with full body treaded star headed screws having minimum frame density of 780 kg/ cbm & manufactured by " RAJSHRI " an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of ( Min. 990 N ), Minimum Compressive Strength of 58 N/mm2 , Modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof , water / Moisture Proof & Fire retardant & Fixed in position with SS Dash Fasteners / Hold Fast of required dia and lenght, , all as per specifications drawings as directed by the Engineer-In-Charge. Material test certificate and authentication should be compulsory provided by the manufacturing company, complete all as specified and directed.

M & L for factory made of 30 mm thick 100% solid WPC laminated skeleton door shutter comparising of vigin PVC resin of K value 57-60 (suspension grade) calcium carbonate and natural fibres (wood powder / rice husk/wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extrauded (inner) with having minimum frame density not less than 650 kg/cbm & manufactured by RAJSHRI an certified by iso9001-2015, having good screw holding capacity (screw withdrael strength of min 2000N) (face) and 1100N (edge), min copressive strength of 50N/sqmm, modulus of elasticity 850N/sqmm and resistance to spread of flame of class A catagory with property of being termite/borerproo,water/moisture proof and fire retareded.WPC to laminated with PVC foil of min 14 micron thick of approved design pasted on both faces of shutter and fixing stainless steel butt hinges of required size with nessesory full body threaded star, complete all as specified and directed.

S & F for stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair for for Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

S&F in repair for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification & drawing, complete all as specified and directed.

M &L for 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned atjoints, complete all as specified and directed.

S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 ®, complete all as specified and directed.

M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggregate) in lintels upto 1.5M clear span, cills, steps seismic and other similar bands, plinth courses, string courses, plinth courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, walter troughs and the like incld weathering, slightly rounded or chamfere angles and throating, complete all as specified and directed.

S&F factory made second class Hard wood 35 mm thick plain framed panelled shutters (any numbers of panels) with panels of timber flat on both sides (feather edged) or of veneered particles board medium density wood particle board with commercial face veneers, complete all as specified and directed.

S&F 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S & F for 100 mm long stainless steel butt hinges, medium weight cold rolled, complete all as specified and directed.

S & F for 150 mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

S&F for 150mm long Extruded Aluminium anodised alloy handles, fabricated type, complete all as specified and directed.

S & F of 250mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F in repair door closer hydraulically regulated, aluminium (extruded section body) desigtnation No 2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg, complete all as specified and directed.

S & F for 140 mm aluminium door stopper, medium weight cold rolled, complete all as specified and directed.

S & F in repair cupboard shutter 20mm thick (style) factory made panel PVC incl chowkhat frame made out of MS tubes 19 gauge for top and bottom rails MS frame shall be covered with heated moulded plain colour PVC channel having a PVC sheet strip of 10mm width stuck inside with solvent cment for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side 10 mm (5mm x 2) thick of 20mm and 20 mm cross PVC sheet and as gap insert for top and bottom rail. panelling for plain colour PVC sheet to be fitted in the m.s frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying fixing in the frame at site as per specification, complete all as specified and directed.

S & F in repair 20 mm thick PVC solid core construction, with PVC solid core and designer face as in shelves, complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of exterior weather coat paint of multi colour pattern in three or more colours as approved by GE, complete all as specified and directed.

VIJAY KUMAR SURI AND SONS (BID ID -3487288)

M/S RAHUL GUPTA (BID ID -3488899)

M/s Anil Engineers & Builders (BID ID -3489785)