WBMAD 89 ( DEV/ MDF/ KM ) 2025-2026

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils Within a lead of 75 m. as directed. The item includes necessary trimming the sides of Trenches, leveling, dressing and ramming the bottom, bailing out water as required complete. (a)Depth of excavation not exceeding 1,500 mm

b ) Depth of excavation for additional depth beyond 1,500 mm. and up to 3,000 mm. but not requiring shoring.

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm. as directed and consolidating same by thorough saturation with water ramming complete, including the cost of supply of sand. (Payment to be made on measurement of finished quantity)

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. In ground floor and foundation.

Cement concrete with graded stone chips (40 mm size) excluding shuttering In ground floor and foundation.

Hire and labour charges for shuttering with centering and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved with required bracing for ……etc. 25 mm. to 30 mm. thick wooden shuttering as per direction of E-in-C.With prop

(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. (Gr. Floor)

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups ,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape ,placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. (a) For works in foundation, basement and upto roof of ground floor/upto 4 m.. SAIL/ TATA/RINL. Total Conc. vol.

Brick work with 1st class Bricks In foundation and plinth a)With cement mortar (4:1) In Fdn. From pedestal to GL.

Brick work with 1st class Bricks In foundation and plinth a)With cement mortar (4:1) In Super structure. (Gr. floor.)

125mm th. Brick work with (4:1) cem. Morter. Gr. Floor.-

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] Gr. Floor:- c)With (1:6) cement morter 10mm thick plaster (4:1) celling roof

(b) 20 mm. thick plaster

© 15 mm. thick plaster (6:1)

M.S. gate of Jail type as per approved design made of strong M.S.frame work, intermediate stiffeners and round / square bars or angles. M.S. sheet (not less than 14 gauge) gussets, cleats etc.including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the Engineer-in -charge. In ground floor.

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor

Applying decorative cement based paint of approved quality after preparing the surface including scraping the same throughly (plasted or concrete surface) as per manufacturees's specfication . (iii) Two Coat

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (iv) Two coats (with any shade except white),

Supplying , fitting , fixing steel rolling shuter profile type with 18 B,G of approved type steel latche section 75mm wide fitted with coil wire spring to nececcery thr fitted of required with wire both inside and outside specially builtup

Gr. Floor -