Reinforcement of Kumunda-III L.I. Project Under State Plan 2024-25 In Talcher Block of Angul District

Civil Works (Part-A)

Earth work excavation in foundation in hard soil with 50 mtr initial lead 1.5 m initial lift including rough dressing and breaking clods to 2 cm to 7 cm and laying in layers not exceeding 0.3 m in depth as per direction of Engineer-in-charge. (Excavation by manually)

Filling foundation and plinth with sand watered and rammed as per direction of Engineer-in-charge.

Cement concrete (1:4:8) with 4 cm size h.g metal as per direction of engineer-in-charge.

Cement concrete (1:2:4) with 12 cm size h.g Chips as per direction of engineer-in-charge.

Rigid and smooth centering and shuttering for RCC work including false work and dismentalling them after casting including cost of materials complete. Foundation plinth bend

RCC (1:2:4) with 12 mm size HG chips as per direction of engineer-in-charge.

Supplying, fitting and placing oncoated HYSD (TISCON) bar reinforcement complete as per drawing and technical specification including cutting, binding, bending and cost of binding wire.

Fly Ash Brick (25cmx12cm x8 cm) having crushing strength not less than 35kg/cm with dimensional tolerance ± 5% in cement mortar (1:6) in foundation and plinth.

12mm thick cement plaster (1:6 ) over brick masonary as per direction of Engineer-in-charge.

Filling F & P with excavated materials, moorum including watering and ramming as directed by the engineer-in-charge

Cement punning over cement plaster as per direction of Engineer-in-charge.

Cost of supplying transportation and fixing in proper place and position including required size full threaded TVS nut bolt with CC (1:2:4) as per site condition

Cost of outlet

Supplying of unplasticised rigid UPVC pipe ivory gray in colour having specific gravity of 1.40 to 1.46 gms.cc, of straight length of 6 (six) meter for portable water suppliers conforming to IS-4985/2000 of BIS- Amendment 2 read with Table =1 of IS specification bearing ISI marks for working pressure CI -IUO=PVC pipe to withstand pressure of 2.5 Kgf/sqcm/4.0 Kgf/sqcm/6.0 Kgf/sqcm/8.0 Kgf/sqcm and the specification and manufacturer name should be prominenity marked on body of each pipe as per the latest Amendment of IS 4985.it includes the cost of sockets in case of plain ended pipe PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubaneswar/ EPM, Orissa, Bhubaneswar necessary approval of authority including transporotation and laying at site all complete with cost of solvent cement.

i) 200 mm dia (Class-I)

10 HP KW Energy efficiency Monoblock pump set of total head 18 mtrs having discharge 1700 LPM with squirrel cage induction motor fitted with bronze impeller TB-2 of IS 318/1981, companion flanges & Class "F"insulation suitable for operation 415 volt +6%-15% 3 phase, 50Hz AC poweer supply suction/deliveery= 100mmx100mm with BEE 3 Star rated energy efficiency Pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership net work for easy availability of spares confirming to IS specification (a) Casing: FC 200 as per IS 210/1978 (b) Impeller: Bronze grade LTB-2 of IS 318/1981 including all cost, conveyance, cess etc complete.

Control Pannel with Automatic Star delta Starter, sheet steel enclosure suitable for operation of Squirrel cage induction motor up to 10 HP with 16 Amp (AC -3) duty contractor at 415 Volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & no volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The Starter should provide dependable protection against over load and single phasing fitted with Volt Meter, Ameter, MCB in complete shape including Indicator Lamp reputed brand of ISI specification including all cost, conveyance, cess etc complete.

Empty Outdoor Irrigation Pannel Board size (0.45mtx0.25mtx1.20m of 18 SWG Cold Rolled M.S Sheet with 4 legs of 300 size with one coat of Red Oxide Primer and two coats of Smoke grey /Navy blue two coats of powder coated paint of approved quality on both side (Inside & Outside) suitable to mount 3Phase Starter, Main Switch and Capacitor inside the Panel Board vertically over 18 SWG M.S.Sheet and the danger board fixed on the top of the Panel Doorreputed brand of ISI specification including all cost, conveyance, cess etc complete.

63 AMP Triple Pole Main switch confirming to IS No.4064(Part I & II) with ISI marking of reputed company having utilisation capacity cagegory AC- 22 reputed brand of ISI specification including all cost, conveyance, cess etc complete.

Motor hood size (0.45mx0.45mx0.60m) made with 18 SWG (cold rolled M.S.Sheet with one coat of red axide primer and two coats of powder coated paint of approved quality on both side (inside & outside) suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for attachement with the groves on rear side of the pannel board of approved brand including all cost, conveyance, cess etc complete as per the direction of the Engineer-In-Charge

Motor base plate made with M.S angle with one coat of red axide primer and two coats of powder coated paint suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for hole for fixing nut & bolt of approved brand including all cost, conveyance, cess etc complete as per the direction of the Engineer-In-Charge.

6 KVAR Power Shunt Capacitor with ISI mark of of reputed approved brand of ISI marked including all cost, conveyance, cess etc complete.

3x16 sqmm PVC insulated (HD) tropoder armoured Electric Cable with alluminum conductor for use in 3 phase power system of working voltage upto & including 1100 volts at 50Hz confirming to IS 7098 (Pt-II) of approved brand of ISI marked including all cost, conveyance, cess etc complete.

100mm dia nominal bore G.I.pipe having wall thickness 4.5mm electrical resistance welded of medium class confirming to IS- 1239(part-1/2004) with latest ammendments, screwed at both ends as per IS-554 with socketed at one end and the other end protected with plastic threaded protector including its transportation and unloading at L.I.P. site. The socket confirming to ISI 1239(part II/1992) with latest ammendments in random length of 4 to 7 mtr.Each pipe should bear IS certification and manufacturers name/trade mark. (As per S/R 2022)

100mm dia G.I.Bend (Medium Duty) conforming to IS No-1239 (part II/1992) with ISI mark of reputed brand including all cost, conveyance, cess etc complete.

100mm dia C.I. Screw boss Foot Valve of swing type friction less with single disc conforming to IS-4038/1979 of reputed brand with ISI mark of reputed company having wide dealership network including all cost, conveyance, cess etc complete. (Kirloskar make)

100mm dia G.I.Flange (Medium Duty) conforming to IS No-6392/1971 with ISI mark of reputed brand including all cost, conveyance, cess etc complete.

100mm dia C.I.Sluice Valve Flanged type PN-1.0 as per (IS-14846-2000 Standard) with ISI mark of reputed brand including all cost, conveyance, cess etc complete. (As per S/R 2022)

100mm dia C.I.Double Flanged Non Return Valve swing type PN-1.0 (IS-5312 (Part-I-2004) with bypass arrangement with ISI mark of reputed brand including all cost, conveyance, cess etc complete (As per S/R 2022) (Kirloskar make)

Cost, supplying of 50mm dia Kirloskar make C.I double Air Release Valve PN 1.6 with saddle and Raiser pipe conforming to IS 14845 (SI) with ISI mark including all cost, conveyance, cess etc complete.

Cost of 200mm dia PVC End Cap.

Labour charge for laying and fitting 200mm PVC pipe

Labour charges for motor, starter delivery and fitting, fixing of suction including fitting of priming Tee, Tee set, NR valve, Sluice valve, Air release valve and minor welding transportation of materials to site etc. including nut, bolt rubber insallation etc complete.

Cost of 200mm PVC D Joint

200x200x200mm PVC equal Tee.

200x200x110mm G.I. Raisar Tee with assoceries

Electrical Works (Part-B)

Construction of 3 Phase L.T line as per REC standard confirming to RE rule 1956 with 300Kg 9 Mtr long PSC pole support in 33 mtr span length with 4x35mm² + 1x35 mm ² LT, XLPE AB cable with coil earthing device, LT dead end clam, Suspension clamp with G I hook, stay accessories such as wire insulator , clamp etc. nut bolts, alongwith concreting copping & padding of poles and stayset as per direction of Engineer in Charge as per TPCOCL specification etc. including cost of all materials, labour , transportation complete with liaising for testing inspection & commissioning as per specification of TPCODL etc complete.

Renovation of 25 KVA Sub Station, replacement of 25 KVA transformer- 1 no., 11KV AB Switch- 1 set, 11KV HG Fuse- 1set, 11KV LA- 3 nos, earthing for S/S-7 nos, G.I. Fensing- 1 no, LT distribution box- 1 no., 55mm2 XLPE cover conductor, 4c x 35mm2 XLPE cable, GI nut bolt, other misc. including cost of all materials, labour transportation, inspection & commissioning etc. complete as per TPCOCL specification etc. including cost of all materials, labour, transportation complete with liaising for testing inspection & commissioning as per specification of TPCODL etc complete.

Electrical Earthing with 40mtr dia medium duty GI earthing pipe each 3 m longwith installation including cost of all materials like GI flange chorcoat, salf etc. as required as per I.E Rule

Other Electrical materials such as pvc tape.7/20pvc copper wire 3/20 pvc copper wire G.I flxible condite pipe no 6 GI wire copper cable socket GI socket and petty materials required for electrical installation. All materials should be as per IS including fitting charges