Improvement of Kamarda Baliapal road from 7/000km to 9/800km and from 10/390km to 12/050km and providing renewal wearing coat on Parulia Bridge in the District of Balasore for the year 2025-26

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth upto 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to be used or auctioned upto a lead of 1000metres including removal and disposal of top organic soil not exceeding 150mm in thickness as per Clause 201 of MoRT&H Specifications for Road & Bridge works (5th Revision) & including cost of all labour, T&P, royalty etc complete and as per direction of Engineer-in-Charge.

Excavation for road work in soil with hydraulic excavator of 0.9cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections and transporting to the embankment locations with all lifts & leads up to 1000m.as per approved Drawing & Technical Specifications and as per Clause - 301 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction as per Technical Specifications and as per Clause - 305.3.4 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Providing G.S.B. Gr-VI stone screaning materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with vibratory roller to achieve the desired density, as per approved Drawing & Technical Specifications and as per Clause - 401 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per approved Drawing & Technical Specifications and as per Clause -406 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

Providing and Applying Primer Coat with bitumen emulsion (SS) on prepared surface of granular base including cleaning the road surface and spreading primer @ 0.60kg per sqm using mechanical means as per Technical Specifications and as per Clause -501 & 502 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance & other taxes of materials, cost of labour, machinery, T&P etc complete.

Providing Tack coat on prepared bituminous surface with bitumen emulsion (RS) and spreading @ 0.20kg per sqm using mechanical means as per Technical Specifications and as per Clause -501 & 503 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance & other taxes of materials, cost of labour, machinery, T&P etc complete.

Providing 50mm compacted thick Bituminous Macadam of grading -2 using crushed stone Gr.-2 materials & 60/70 penetration grade of bitumen preparing preemixed materials with bituminous binder with hot mix plant, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per clauses 501 and 504 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

Providing 25mm compacted thick S.D.B.C. of grading -2 using crushed stone Gr.-2 materials & 60/70 penetration grade of bitumen preparing preemixed materials with bituminous binder with hot mix plant, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per clauses 501 and 508 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

terials, cost of labour, machinery, T&P etc complete as direction of Engineer-in-Charge.

Providing compacted granular materials in shoulder / diversion road by using moorum having required P.I. value with sand admixture if required, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with vibratory roller to achieve the desired density, as per approved Drawing & Technical Specifications and as per Clause - 407 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site mixing with sand ( To bring the soil not be less than 6.50 % CBR) with a proportion of 60 :40 spreading , mixing at a place by tractor, rotavator, grading to required slope and compacting at OMC by vibratory roller to meet the requirments of table -300-2 as per clause 305 of MoRT&H specification for road & bridge works (5 th revision).

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 as per approved Drawing & Technical Specifications and as per Clause -305 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from foundation of CD & structures graded and compacted to meet requirement of table 300-2 as per approved Drawing & Technical Specifications and as per Clause -305 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Providing and laying 25 mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in Table 500-29, prepared by using mastic cooker and laid to required level and slope after cooking the surface,including providing anti-skid surface with bitumen precoated fine grained hard stone chipping of 13.2 mm nominal size at the rate of 0.005 cum per 10 sqm and an approximate spacing of 10 cm center to center in both directio, pressed into surface when the temperature of surfaces is not less than 100° C, protruding 1 mm to 4 mm over mastic surface including cost, conveyance, royality of all materials & cost of all labour, machinery etc complete as per Clause 516 of MoRT&H Specifications for Road & Bridge works (5th Revision).

20mm thick cement plaster (1:4) over stone masonry, watering, curing including cost, conveyance, royality of all materials & cost of all labour, machinery etc complete as per approved Drawing & Technical Specifications and Section 1400 & 2200 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Providing road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads@250gms per sqm area , thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35.The finished surface to be level, uniform and free from streaks and holes etc. for finished item of work as per approved drawing and technical specification complete in all respect as per Section 900 and Clause 803 of MoRT&H specification for road and bridge work (5th Revision) & including cost & conveyance of all materials, labour, T&P, royalty etc complete and as per direction of Engineer-in-Charge.

Providing & fixing of RCC M-15 grade ordinary km stone of standard design as per IRC:8-1980, fixing in position with painting & printing including cost, conveyance, royality of all materials & cost of all labour, machinery etc complete as per Technical Specifications and Section- 800, 1600 & 1700 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Providing and fixing of direction and place Identification Signs up to 0.9 sqm. Size (1200mm x 700mm) Board retro-reflectorised, cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting vide clause 801.3 ,fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle post 75m x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing. The sign shall be maintanined as per Section 12 of IRC-67 of MoRT&H specification for road & bridge works (5th Revision) and as per direction of Engineer-in-Charge.

Providing and fixing of 60cm circular size retro-reflectorised, cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting vide clause 801.3 ,fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle post 75m x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing .

Providing & fixing of RCC M-15 guard Post of 1.0m height and 15cm dia using 3.5kg steel reinforcement per each as per IRC:8-1980, fixing in position with painting & printing including cost, conveyance, royality of all materials & cost of all labour, machinery etc complete Technical Specifications and Clause- 804 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Providing & erecting a "W" metal beam crash barrier comprising of 3mm thick corrugated steel metal beam rail, 70cm above road/ ground level fixed ISMC series channel vertical post 150mm x 75mm x 5mm spaced 2m centre to centre, 1.8m high, 1.1m below ground / road level, all steel part & filments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixedon the vertical post with a spacer of channel section 150mm x 75mm x 5mm, 330mm long complete as per clause-811 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Provding & Fixing of Road Stud 100x100mm, die cast in aluminium resistcent to corosive effect of salt and grit, fitted with lense refector installed in concrete or asphaltic surface of drilling hole 30mm upto a depth of 60mm & bedded in suitable bitminous grout or epoxy mortor, all as per BS 873 Part-4:1913 as per Technical Specifications and Section- 800, 1600 & 1700 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Gravel backing to aprons & revetments and providing filter material using gravel underneath pitching in slopes as per approved drawing and technical specifications complete in all respect as per Section 900, 1000 & 2500 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost & conveyance of all materials, labour, T&P, royalty etc complete and as per direction of Engineer-in-Charge.

Supplying, fitting and fixing of Road way indicator (Delineator) confirming IRC 79 as per direction of Engineer-in-Charge.

Providing and fixing of 90cm octagon size retro-reflectorised, cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting vide clause 801.3 ,fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle post 75m x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and Specifications for Road & Bridge works.

Providing & Fixing of (Delineator) Roadway Indicator, form of guide posts made of Mild steel with pure polyester powder coating with the minimum thickness of powder coating of not less than 40 micron, the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base, conforming to IRC:79 Specifications for Road & Bridge works.

Sand filling in Road work & foundation of structure as per approved Drawing & Technical Specifications and as per Section - 2100 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, T&P etc complete as direction of Engineer-in-Charge.

P.C.C. M-15 Grade in foundation bed as levelling course using 40mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section - 1700 & 2100 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete as direction of Engineer-in-Charge.

P.C.C. M-15 Grade in Substructure of structure & CD work with formwork using 40mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section -1500, 1700, 2100 & 2200 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of ma

Providing 300mm dia @ 6.00mtr deep single under reamed pile foundation with RCC M25 using 12mm size black hard granite (Crusher broken) stone chips inclu

Providing & fixing of Reinforced cement concrete M-15 grade hectometre stone of standard design as per IRC:8-1980, fixing in position with painting & printing including cost, conveyance, royality of all materials & cost of all labour, machinery etc complete as per Technical Specifications and Section- 800, 1600 & 1700 of MoRT&H Specifications for Road & Bridge works (5th Revision).

R.C.C. M-20 grade in Foundation of wing wall of Box Culvert with formwork using 20mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2100 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

Rough stone dry packing in aprons and revetments and stone pitching in slopes and boulder approns etc with hard granite stone of size 30 cm and above as per approved drawing and technical specifications complete in all respect as per Section 900, 1000 and 2500 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost & conveyance of all materials, labour, T&P, royalty etc complete and as per direction of Engineer-in-Charge.

Provision of an Reinforced cement concrete crash barrier at the bridge decks & approaches to bridge structures ,constructed with reinforced cement concrete with HYSD reinforcement conforming MoRT&H specification and as per details given IRC-5 including dowel bars,expansion joints filled with pre-moulded asphalt filler board etc. and approved drawing and at location directed by the Engineer, all as specified

Providing weep holes in abutment, wing wall, retaining wall, toe wall and RCC drain etc with 100mm dia A.C. pipe as per approved drawing and technical specifications complete in all respect as per Section 2200 & Clause 2706 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost & conveyance of all materials, labour, T&P, royalty etc complete and as per direction of Engineer-in-Charge.

Metal spall backing to the wall steining or weep holes of abutments, deep drain with hand brocken stone aggregates of 50mm size as per approved Drawing & Technical Specifications for finished item of work including cost, conveyance, royality & other taxes of materials, cost of labour, T&P etc complete as per the direction of the Engineer-in-charge.

Providing and laying cement concrete grade M20 using 20 mm nominal size coarse granite aggregate conforming to Table 1000-1 in foundation, complete including formwork as per section no. 1000, 1500, 2100 of specification for road & bridge works of Ministry Of Road Transport & Highways ( 4th revision ) & direction of Engineer -in-Charge.

Concrete Drain Raft

Concrete Drain Wall

Concrete Drain Slab

R.C.C. M-25 grade in Foundation raft of RCC Box culvert/Retaining Wall with formwork using 20mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2100 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

R.C.C. M-20 grade in substructure of wing wall of Box Culvert with formwork using 20mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2200 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

R.C.C. M-25 grade in superstructure of RCC Box culvert with formwork using 20mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

Dismantling Precasted / Reinforcement cement concrete of grade M-20 and above including T&P and scaffolding wherever necessary, sorting the dismantled materials disposal of unserviceable materials and stacking the serviceable materials with all lifts and lead of 1000m etc.complete as per Clause -202 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Painting two coats with synthatic enamel paints over a coat of primer on any elevation on road kerb, parapet and guard post for finished item of work including cost, conveyance & other taxes of materials, cost of labour, T&P etc complete as per the direction of the Engineer-in-charge.

Supplying, Cutting, Bending, Binding, Straightening, Placing HYSD bars confirming to grade I.S.1786-1985 (Fe-500) for steel reinforcement works for finished item of works as per drawing and technical specification and as per Section.900, 1000, 1600,2100, 2200 & 2300 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Providing and fixing of 90cm equilateral triangle size retro-reflectorised, cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting vide clause 801.3 ,fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle post 75m x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing. The sign shall be maintanined as per Section 12 of IRC-67 of MoRT&H specification for road & bridge works (5th Revision) and as per direction of Engineer-in-Charge. .

ding cost of boring but excluding cost of M.S./Tor steel and labour charges for cutting, bending and binding of steel as per direction of Engineer-in-Charge.

Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints as per approved Drawing & Technical Specifications and Section 2600 of MoRT&H Specifications for Road & Bridge works (5th Revision).

Providing and fixing of 80cm x 60cm rectangular size retro-reflectorised, cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting vide clause 801.3 ,fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle post 75m x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and Specifications for Road & Bridge works..

Dismantling of Bituminous Course including stacking the useful materials for reuse and removing the debris within 50mt lead including all labour,machineries, scaffoldings, T&P, Sundries complete as per specification and direction of Engineer-in-Charge.

R.C.C. M-30 grade in wearing coat including steel of C.D. work with form work using 20mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section -1500, 1600, 1700 & 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.

R.C.C. M-30 grade in Railing of Culvert / Bridge for rails panel in 2 ties as per approved Drawing & Technical Specifications and as per Section -1600 & 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labou, T&P etc complete.

Providing and laying plain cement concrete grade M20 using 20 mm nominal size coarse granite aggregate conforming to Table 1000-1 in foundation, complete excluding formwork as per section no. 1000, 1500, 2100 of specification for road & bridge works of Ministry Of Road Transport & Highways (5th revision) & direction of Engineer -in-Charge.

Removal of existing cement concrete wearing coat including its disposal complete as per Technical specification without causing any detrimental effect to any part of the bridge structure and removal of dismantled material with all lifts and lead upto 1000 m & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

R.C.C. M-25 grade in substructure of RCC Box culvert/ retaining wall with formwork using 20mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2200 of MoRT&H Specifications for Road & Bridge works (5th Revision) including cost, conveyance, royality & other taxes of materials, cost of labour, machinery, T&P etc complete.