PROVN OF STANDBY GENERATING SET AT STATION AUDITORIUM (MENAKA) AT

Amount

Supply and installation of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with relay panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per CPCB norms and foundation etc. of capacity 200 KVA.

M&L for Earthing complete with Copper earth plate electrode 60×60cm.× 3.15mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to Copper Strip 20x3 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Supply laying and testing cable XLPE insulated screened PVC beded,galvanized steel trip or wire armoured, electric power cables (heavy duty) 1100 Volt grade wiyh stranded aluminium conductor of size 185 sq mm 3,1/2 core.

Supply & fix exhaust fans AC three phase 415 V of size 450 mm sweep with louver.

Supply laying and testing cable XLPE insulated screened PVC beded,galvanized steel trip or wire armoured, electric power cables (heavy duty) 1100 Volt grade wiyh stranded aluminium conductor of size 120 sq mm 3,1/2 core.

Supply laying and testing cable XLPE insulated screened PVC beded,galvanized steel trip or wire armoured, electric power cables (heavy duty) 1100 Volt grade wiyh stranded aluminium conductor of size 25 sq mm 3,1/2 core.

Excavatioin in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and taking out hard/dense soil for laying of cable /erection of pole/stay pit excavation

M&L for dry river sand for cable cushoining laid in trenches for protection of cable

M&L for bricks sub class 'B' old size well burnt for cable protection all as specified and directed

Returning and filling including spreading levelling watering and well ramming in layers not exceeding 25 cm

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point

Supply, fabricate, errect, connecting, testing & commisioning LT Panel, Outdoor Type, weather and vermin proof made out of 3 mm thick CRCA sheet with front & Rear opening and locking arrangement, epoxy powder coated having colour siemens grey, 400 Amps capacity aluminium bus bar for phase, 3 No's and 1 No 200 Amp bus bar for neutral, mounted on epoxy insulator including neccessary copper control wiring, heat shrinkable, RYB coloured sleeves over bus bar for identification, earth shields, circular holes at bottom / top to receive incoming and outgoing cable, cable lugs, cable gland of sizes as required floor mounting angle iron frame made out mild steel angle iron of size 40 x 40 x 6 mm grouted on PCC (1:3:6) upto required height suitable for the following control/ fitments sensible for 3 phase, 50 Hz, 415 V system complete with and including following :- Main Incoming (from AMF Panel) - MCCB 4 pole 415 V 400 Amps 36 KA Thermal Magnetic adjustable type :- 01 Nos Outgoing (for existing Panel No 2 - Back Side) MCCB 4 pole 415 V 250 Amps 35 KA Thermal Magnetic adjustable type :- 01 Nos Outgoing (for existing Panel No 1 - front Side) MCCB 4 pole 415 V 160 Amps 35 KA Thermal Magnetic adjustable type :- 01 Nos

Excavating in post holes (or similar holes) each n. exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface in soft/loose soil

Excavation in trenches n.exc 1.5m wide n.exc 1.5m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 Sqm on plan and n.exc 1.5m depth and getting out in soft/loose soil

M&L for providing cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete.

M&L for Brickwork with Modular bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 in narrow widths including Cutting out bricks/stone, forming toothing for, and bonding new into old brickwork /stone masonry

M&L rendering 15mm thick in CM (1:4) on fair face of brick/concrete surfaces finished even and smooth without using extra cement complete

S & F mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165

S&F Mils steel screw bolt (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm and n.exc 10cm long

Supply only chain link fencing, MS galvanised of any size and type complete all as specified and as directed

Fixing only chain lnk fencing including line wires, any mesh, size, any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed Note : chain link fencing and line wire shall be measured and paid separately as " supply only"

S&F Mild steel round bars 10mm dia , Gde E-250 FE 410-W cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete Fe-410-W (Gde- E-250) Quality A..

Preparing new or previously untreated steel surface of any description, over 10 cm in width or girth not other wise described and appying two coats of synthetic enamel paint over one coat of red oxide primer.

M&l Preparation newly or plastered surfaces of brick/concrete and applying three coats of white wash on sufaces of wall complete.

M&L for providing cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete

S&F plates(plain or chequered) channels,square cut or notched (ordinary and counter shunk forming holes,without any attachement. All as specified and directed by Engr-in-Charge

S&F steel work in Tubular trusses, vertical post connecting to plates, including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 complete

S&F Rolled mild sections as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fsatenings and heavy brackets framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. quality conforming Fe-410-W (gde-E-250) quality - A

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

M&L Moorum/Red bajiri filling in floors or pavings, laid in layers n.exc 15cm thick spread levelled and rammed including watering complete all as specified and directed.,

M & L for Hard core of broken stone of gauge n. exc 63mm deposited, spread & leveled in layers n.exc 15cm thick watered and rolled/rammed to a true surface all complete as directed by Engr-in-Charge.

M&L for Plain cement concrete work (Ready Mix Concrete only) in pavement/hard standing M-30 grade, thickness of concrete 25cm or less including necessary use & waste of form work complete all as specified and as directed.

Surface Excavation not exceeding 30cm deep and getting out in any type of soil

M&L for forming 20mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'A' for concrete slab thickness 150 mm all as speicified and directed.

Supply and lay pipe galvanized, “Medium class”, including fittings 50 mm (2”) dia.

Supply and lay pipe galvanized, “Medium class”, including fittings 40 mm (1.5”) dia.

Supply and lay pipe galvanized, “Medium class”, including fittings 25 mm (1”) dia.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of dia 25 mm

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of dia 40 mm

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of dia 50 mm

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out in soft/llose soil including making the bottom of trenches levelled for proper laying of pipe line, foundation etc or for shafts, cesspits, manholes, pier hole etc not exceeding 10 sqm on plan and getting out in soft/loose soil as specified and as directed.

M&L for cutting /breaking of cement concrete path or bituminous road of any thickness with or without reinforcement for taking up/down of GI/CI pipes and connection and making good to match xisting surface by PCC (1:2:4) type B1 (Using 20 mm graded stone aggregates) complete all as specified as directed.

Cutting Existing 80/100mm bore CI water mains and inserting ferrules of size 25mm dia for taking branch connection including fittings all as specified and directed.

Supply and fix Straight plain brass ferrules 25mm dia or connecting screws) screwed both ends and fixed all as specified and directed.

SHAILENDRA B TULSANI

M/s S.D Construction Co

MONA GENERATOR SEVICES PVT. LTD.

Prasur Electricals & Engineering Co.