Interior fitout work in the office space of Agriculture insurance company of India Limited at Bhubneshwar and Guwahati

3 Grand Total Inclusive GST 45,948,511.00

S NO DESCRIPTION AMOUNT AMOUNT

3.00 ELECTRICAL WORKS 2,587,514.00 1,732,222.11

5.00 WI-FI & LAN WORKS (ACTIVE & PASSIVE) 0.00 2,393,094.00

8.00 FIRE ALARM & PA SYSTEM 236,544.00 11,610.00

Total (DSR+MR) 25,424,694.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

DSR ITEM NON DSR ITEM

1 FLOORING WORKS

CEMENT CONCRETE : Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and

shuttering-all work upto plinth level.

4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) CUM 19.00 6,812.00 129,428.00

IPS FLOORING: 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener

1.02 11.4 consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed SQM 177.00 978.45 173,185.65

@ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of

nosing of steps etc. complete.

VITRIFIED TILES : Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick

11.41A cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white

1.03 cement and matching pigments etc., complete. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be

done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

VITRIFIED TILES : Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water

absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12

mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the

joint with white cement & matching pigments etc. complete.

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness

1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement,

1.06 including cement slurry, but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 354.00 614.20 217,426.80

TOTAL FLOORING WORKS 1,845,132.65 38,570.00

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING : Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre,

one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

2.01 12.45 wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed

to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all

as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) SQM 802.00 1,355.80 1,087,351.60

ACOUSTIC CEILING: Providing and fixing suspended Demountable acoustic ceiling in recessed grid system -Danoline: Belgravia 300

x 1200 x12.5mm E with Unity 3,square 3.5mm holes, with 0.80 NRC* Material: High Grade Glassfiber Reinforced Perforated

2.04 MR plasterboard with Cleaneo Technology Board type: Ceiling tile Length x width x thickness: 300x1200x12.5mm Edge: E recessed grid SQM 176.00 3,200.00 563,200.00

system (8mm recess)

Perforation: Unity 3, 3.5x3.5 Surface: Water-based acrylic paint ,Colour: White NCS 0701 Y24R, closet match to RAL 9003; gloss 5

TOTAL FALSE CEILING WORKS 1,087,351.60 563,200.00

3 WALL FINISHES WORKS

1 Digitally signed by AMIT

GLASS PARTITION (FIXED GLASS PARTITION WITH 10MM GLASS): Providing & Fixing of Modular Single glazed partitioning

frame make 45mm System, Using KL 45 001 (45mm x 25mm) as wall starter section, Using KL 45 001 & KL 45 002 (45mm x25mm) as

3.01 MR Top & bottom channel. Toughened Glass of thickness 10mm to be installed with required accessories ie glass to glass aluminium I SQM 30.00 4,400.00 132,000.00

sections, T section & 90 degree sections as per the requirement & Glass packing to adjust the floor level. Insertion of

silicon/Thermoplastic gasket to adhere the glass firm & airtight. Partition Height Considered is 2500mm

FRAMELESS HINGED GLASS DOOR: Providing & Fixing of Modular Aluminium single leaf Stile door frame of make 45 mm System

duly Anodized Aluminium Sections using KL 45 001 & KL 45 003 (45mm x 45mm) and Stile door of size 60x35mm as door frame with

3.02 MR Toughened Glass of Thickness 10 mm. Hardware as per make list and Lever Handle with Mortise Lock, Exposed Door Closer, Set of

4 Hinges, Door Stopper and required accessories ,Silicone/Thermoplastic Gaskets & Screw Caps.

WOODEN DOOR FRAMES : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed

9.1 and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

3.03 separately).

9.1.1 Second class teak wood CUM 1.00 142,949.70 142,949.70

FLUSH DOOR SHUTTERS : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

9.21 core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains

3.05 or cross bands and face veneers on both faces of shutters:

9.21.1 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 15.00 2,392.65 35,889.75

WOODEN LIPPING : Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

shutters (over all area of door shutter to be measured).

Providing and Fixing 22x922 mm D-type Handle Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of approved make

and model all complete as per the direction of Engineer-in-charge.

Providing and Fixing SS Mortise Lock Body SB/TB for door thickness 25-50 mm for of approved make and model all complete as per

the direction of Engineer-in-charge.

Providing and Fixing Double cylinder Floor Spring- with Closing Force EN 3 with Maximum door weight 105 Kg. Maximum door width

950mm.Closing speed : 130°

3.09 MR Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested with 5 Each 115.00 7,850.00 902,750.00

Years Warranty against manufacturing defect. CE certified for wooden doors all complete as per the direction of Engineer-in-charge.

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and

3.10 9.53 embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm EACH 24.00 228.85 5,492.40

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce

Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having

3.11 MR minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch SQM 50.00 1,200.00 60,000.00

(0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors). Contractors

payment wouldn't be released until & unless he/she produces orginal warranty certificate from the manufacturer.

ACOUSTIC PANELLING: PET Panels made of Polyester in size 2440x1220 mm with thicknesses of 9mm. Density is 1650 gsm for

9mm. The panel can plain/printed/ embossed/ customized to form different patterns. Panels can be cut to customize shape and size to

make different patterns. The acoustic panels should have an NRC of up to 0.3-0.6 Bollard PET Panels should be made of recycled

3.12 MR material and should be 100% recyclable. The panels need to be installed as per approved pattern and color on a plain wall. The panel SQM 50.00 2,620.00 131,000.00

needs to be glued or nailed with headless nails. Thickness: 9 Sheet Size: 2440mm x 1220mm Tolerance: +/- 5% Density: 1650 gsm

Fire Resistance: EN13501 – Class B s1, d0(SGS) NRC: 0.3 – 0.6mm, depending on the air gap between the wall and the panel

Shades: 36 shades available Material: 100% Polyester

LACQUERED GLASS: Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of approved color by Client /

Engineer in charge, fixed with compatible neutral grade silicon on a perfectly levelled 12mm thick water proof marine plywood / MDF /

Mineral fibre board which is mounted on RCC wall/any other structure. Lacquered glass must be made industrially (using curtain

3.13 MR coating process); opaque (if viewed against a support wall), uniformly coated with PU lacquer (50 micron thick coating or more); panel SQM 50.00 3,900.00 195,000.00

to panel colour consistency (measured by photo spectrometer); highly durable (passes hardness test for minimum 220 oscillations);

humidity resistance (conforms to BS EN 1036 1999 or equivalent) ; environmentally friendly having Low VOC (no lead, no arsenic,

no copper, no formaldehyde), low VOC content <100g/l. Silicone used should not react with lacquer coating (compatible neutral cure

2 Digitally signed by AMIT

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both

side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

9.105 and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with

3.14 nylon plugs at spacing of 450mm centre to centre, and fixing of boards to both side of frame work by 25mm long dry wall screws on

studs, floor and ceiling channels at the spacing of 300mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99mm width (0.9mm thick having two flanges of 9.5mm each) to be provided

at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush

finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two

coats of primer suitable for board as per manufacturer's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming

to IS: 2095: part 3 (Board with BIS certification marks)

ACRYLIC SOLID SURFACE CLADDING : Providing & fixing of straight Paneling for walls & Columns structures anchored in floor slab

& celling, cladded with Acrylic Solid Surface 6mm thick sheets straight fabricated on a single face, finished in matte finish, pasted with

industrial grade silicon on a robust substrate. Substrate shall be with suitable MS box sections [Appx. 15 to 20 kg/ Sqm] as per

3.15 MR structural requirement & duly painted with anti-rust red oxide coating and covered with 12 mm thick water proof ply as per the design SQM 20.00 9,210.00 184,200.00

and dimensions approved. The proposal includes the cost of preparing appropriate substrate surface over the civil structure provided,

along with material cost & installation / fixing on straight walls etc. FOR ALL WALL CLADDING, TABLE TOPS ETC. COMPLETE

ROLLER BLINDS : Providing & supplying of Window Blinds as per the approved sample in required shade and style consisting, of

Roller Blinds comprising of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m,

Thickness 0.67 mm, Yarn count 18-19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-5659-2 .The tear

resistance should be complying to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick,easy and

safe installation,moulded plastic with steel spring support and inserted into the tube end. It shall be driven by a ball chain pulley with

ball chain and can be positioned at right side or left hand side of the Shade. The Shade when lowering or raising, shall be

automatically locked in position upon release of the ball chain by means of a built in friction lock.Universal clutch for left and right

hand operation.Chain Gear Ratio of 1.75:1.The END PLUG shall be molded of plastic witha steel location pin. The plug shall be

3.16 MR inserted into the tube end. (Opposite to the Drive Unit) for ease of installation. TheSUPPORT BRACKETS shall be of coated steel & SQM 139.00 1,871.00 260,069.00

provided with covers and used in right hand or left hand positions differentiated by the acceptance of the of the rectangular drive unit

support or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket should be

protruding outside maximum of80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter & skin thickness

of 1mm and shall incorporate a key way integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom

made up of powder coated steel. The BALLCHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls moulded co-axially to

it on 6mm pitch to form an endless ballchain.It is used for raising or lowering action of the shades.hall be suitable for sill, face or side

facing. Cord Equalizer shall be injection melded from impact modified acrylic with a high flexural modulus

PELMET: Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed three layer or graded plain wood particle board

medium density grade I, ISi marked and conforming to IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming

3.17 9.42 to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with RM 56.00 600.55 33,630.80

25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet

and rawl plugs 75 mm long etc. all complete.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level

3.18 up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 5.00 1,123.80 5,619.00

3.19 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. Sqm 5.00 104.80 524.00

13.4 12 mm cement plaster of mix :

3.21 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth Sqm 360.00 262.70 94,572.00

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,

Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives

New work (Two or more coats applied @ 1.43 litre/10 sqm) over and including priming coat of exterior primer applied @ 0.90 litre/10

PLY: Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved primer on one face, and

3.23 fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type SQM 360.00 1,224.65 440,874.00

3 Digitally signed by AMIT

4MM THICK MDF BOARD: Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved

3.24 MR primer on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge

4mm thick MDF Board SQM 230.00 270.00 62,100.00

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section placed at 600mm centre to centre

3.25 MR both ways (horizontal & vertical) fastened to floor, ceiling and horizontal member. The item includes providing and fixing 50mm thick SQM 75.00 1,347.00 101,025.00

polyester synthetic insulation as insulation of 100 GSM.

LAMINATE: Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high

3.26 9.127.2 density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of SQM 230.00 897.30 206,379.00

adhesive of approved quality. 1MM THICK

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter

3.28 to be measured):

9.24.1 Rectangular or square SQM 20.00 199.15 3,983.00

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket

21.3 etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be

3.29 paid in basic item):

21.3.3 With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) SQM 14.40 1,685.40 24,269.76

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm

3.30 12.57 thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI SQM 360.00 358.50 129,060.00

wire etc. complete as per directions of Engineer-in-Charge.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade

10.27 (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in

3.31 frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.

TOTAL WALL FINISHING WORKS 1,363,184.41 2,469,292.00

4 MISCELLANEOUS WORKS

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C.,

kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of

4.03 22.3 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including SQM 0.00 769.60 0.00

rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per

sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to

each other with bitumen @ 1.7 kg/sqm).

SHOP DRAWINGS: Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions etc.

4.04 MR and any other details as and when desired by Engineer Incharge/ client. A qualified professsional for the purpose shall be appointed LS 0.00 250,000.00 0.00

after due appproval from Engineer InCharge.

TOTAL MISCELLANEOUS WORKS 0.00 0.00

4 Digitally signed by AMIT

SCHEDULE OF QUANTITIES (SANITARY/ PLUMBING)

TOTAL AMOUNT TOTAL AMOUNT

TOTAL AMOUNT TOTAL AMOUNT

DESCRIPTION OF ITEM QTY UNIT RATE DSR (INR) NON-DSR (INR)

17.10.1 Kitchen Sink with Drain Board

Providing and fixing P.V.C. waste pipe for sink or wash basin including

2 17.28 P.V.C. waste fittings complete.

17.28.2 Flexible pipe

3 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

17.70.2 Bottle trap 38 mm single piece moulded with height of 270

mm, effective length of tail pipe 260 mm from the centre of

the waste coupling, 77 mm breadth with 25 mm minimum 1 Each 375.65 375.65

water seal, weighing not less than 263 gms

Providing and fixing C.P. brass bib cock of approved quality to conforming

18.49.1 15 mm nominal bore 1 Each 506.80 506.80

Providing and fixing C.P. brass long body bib cock of approved quality

5 18.51 conforming to IS standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore 2 Each 798.95 1597.90

Providing and fixing C.P. brass stop cock (concealed) of standard design

6 18.52 and of approved make conforming to IS : 8931.

18.52.1 15 mm nominal bore 1 Each 670.45 670.45

Providing and fixing C.P. brass angle valve for basin mixer and gyser

points of approved quality conforming to IS : 8931

18.53.1 15 mm nominal bore 4 Each 574.30 2297.20

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm

high and 112 mm distance from wall of standard shape with bracket of the

8 17.71 same materials with snap fittings of approved quality and colour, weighing 1 Each 168.35 168.35

not less than 105 gms

Cutting chases in brick masonry walls for following diameter sand cast

iron/centrifugally cast (spun) iron pipes and making good the same with

9 17.61 cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone

aggregate 12.5 mm nominal size) including necessary plaster and

pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

10 18.76 Cutting holes upto 30 X 30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks 1 Each 416.80 416.80

1 Digitally signed by AMIT

Making chases upto 7.5 X 7.5 cm in walls including making good and

finishing with matching surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain &

brass threaded fittings, including fixing the pipe with clamps at 1.00 m

12 18.7 spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and testing of joints complete as per direction of Engineer

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes 10 M 335.00 3350.00

18.7.3 25mm nominal outer dia pipes 2 M 401.44 802.88

18.7.4 32mm nominal outer dia pipes 2 M 518.75 1037.50

18.7.5 40mm nominal outer dia pipes 2 M 702.95 1405.90

18.7.6 50mm nominal outer dia pipes 2 M 934.15 1868.30

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain &

brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

13 18.8 This includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls

18.8.1 15mm nominal outer dia pipes 10 M 497.80 4978.00

18.8.2 20mm nominal outer dia pipes 5 M 537.60 2688.00

18.8.3 25mm nominal outer dia pipes 2 M 627.25 1254.50

18.8.4 32mm nominal outer dia pipes 2 M 739.30 1478.60

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain &

14 18.9 brass threaded fittings. This incudes jointing of pipes and fittings with one

step CPVC solvent, trenching, refilling, and testing of joints complete as

per the direction of the engineer incharge

18.9.6 50mm nominal outer dia pipes 2 M 794.25 1588.50

Providing and fixing gun metal gate valve with C.I. wheel of approved

quality (screwed end).

18.17.1 25 mm nominal bore 1 Each 622.40 622.40

18.17.1A 20 mm nominal bore 1 Each 539.95 539.95

16 18.21 Providing and fixing unplasticised PVC connection pipe with brass unions.

18.21.1 30 cm length

18.21.1.1 15 mm nominal bore 4 Each 85.00 340.00

17 MR Supply Installation, Testing and Commisioing of 15 liter geyser 1 Each 15000 15000

2 Digitally signed by AMIT

Providing, fixing, jointing and testing in position of ISI marked UV

stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS :

13592 suitable for rubber ring joints, including all neccessary specials and

fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without

doors), reducers, WC connectors, couplers, expansion joints / bellows,

cowels, clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor

level supported by clamp & hangers etc. in concealed / inside duct / under

floor & basement ceiling / external work etc. including chase cutting as

18 MR required, excavation and back filling in all kind of soils, suspended from

floor under false ceiling or embedding the pipes laid under floors / building

in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) including cost of shuttering

for proper completion of the work, breaking and making good the walls

and floors etc. after pipes have been duly laid and tested. The rubber ring

shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts,

washers etc on 50x50x5 mm slotted angle. The cost will include all

support arrangements. The work includes commissioning of all pipes lines

as per drawings and specifications and as directed by engg-in-charge at

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 15.00 metre 536.00 8040.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 3.00 metre 416.00 1248.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985)

UPVC pipes of min 6 Kg/ Sqcm rating with fitting for waste pipe from

fixtures to floor trap including reduces, enlarger, socket, couplers, bends,

19 MR tees etc including fixing at wall/ ceiling level supported by clamp & hangers

etc. cutting holes in wall/ floors/ slabs and making good the same with

cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless

steel grating complete in all respects.

21 MR Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser 4 each 536.00 2144.00

Extra for providing & fixing 125 mm dia C.P. grating in place of C.I.

grating over floor traps.

Providing & fixing of SS Floor Cleanout, round or square with rubber seal

23 MR and flat round cover with screws and other required fitting complete as 4 each 1001.00 4004.00

3 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

1.10 conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

1.55 surface / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.3 1.12 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS Metre 4260 334.00 1422840.00

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

1.24 box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 388 122.00 47336.00

1.24.5 6 pin 15/16 amp socket outlet Each 36 197.00 7092.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

A.6 1.26 excluding modular plate as required. Each 10 40.00 400.00

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

1.5 sq. mm + 1 X 1.5 sq. mm earth wire

1 Digitally signed by AMIT

B.1 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 20 439.00 8780.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 60 1005.00 60300.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 60 1365.00 81900.00

Supplying and making end termination with brass compression gland and aluminium lugs for

9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

Conductor Cables :

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively &

C.2 ISI marked.

(c ) 3.5 C x 70 Sqmm XLPE cable 102.70 2054.04

(d) 3.5 C x 50 Sqmm XLPE cable RM 50 510.00 25500.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 50 378.00 18900.00

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

D.2 connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

D.4 required. (But without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 6 9081.00 54486.00

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

the existing MCB DB complete with connections, testing and commissioning etc. as required.

2 Digitally signed by AMIT

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supplying and fixing following modular switch / socket on the existing modular plate & switch

1.24 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 10 148.00 1480.00

1.24.6 Telephone socket outlet Set 87 148.00 12876.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 10 1639.26 16392.56

E.9 (b) 225mmx38mm(GI) - 3 compartment Mtr 20 1339.36 26787.18

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables

at the intersection of raceways supplied completely with base and cover plates, height

MR adjustable junction box 65- 90 mm including all accessories ss plate of 3mm thick complete

in all respect as per the directions of engineer in charge

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.11 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Meter 300 47.00 14100.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

1.21 surface/ recess including cutting the wall and making good the same incase of recessed

E.12 conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S.

cable trays of perforation of not more than 17.5% in convinient sections, joined with

4.1 connectors suspended from the cieling with MS suspenders including bolts and nuts painting

suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 10 1137.00 11370.00

E.14 1.18 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper

1.18.1 conductor,

1 Pair unarmoured telephone cable in the existing surface/ recessed steel/ PVC conduit Meter 1740 31.00 53940.00

Earthing with GI earth plate 600 mm X 600 mm X 6 mm thick including accessories, and

F.1 5.4 providing masonry enclosure with cover plate having locking arrangement and watering pipe SET 4 7472.00 29888.00

of 2.7 metre long etc. with charcoal/ coke and salt as required.

3 Digitally signed by AMIT

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 100 70.00 7000.00

G PANEL BOARDS

Floor Panels/HVAC Panel

Fabricating, Installing, Testing & Commissioning of automatic mains failure control

including auto by-pass panel, suitable for 125 KVA silent type DG set complete with

relays, timers, set of CTs for metering & protection and energy analyser to indicate

currents, phase and line voltages, frequency, power factor, KWH, KVARH & provision

for overload, short circuit, restricted earth fault, under frequency, control cabling from

AMF panel to diesel engine and elsewhere if required, all complete and inter locking

including the following:sheet steel cubicle type panels fabricated from 14 guage

thick CRCA sheet, dust and vermin proof, indoor type MV Panels with hinged lockable

Colour: Gray Powder Coated, as per approved sample.

Note: All MCCBs of 250 amps and below rating shall be provided with thermal

magnetic release

1nos, 160 Amps. & pole

Four MCCBs above

Moulded 250 Circuit

Case amps Breaker

rating shall be breaking

of fault providedcapacity

KA (ICS=100% ICU up to 433 V) completewith extended Rotary Mechanism and

Spreader Link Set with microprocessor release for O/L, S/C & E/F protection.- Mains

1nos, 160 Amps. Four pole Moulded Case Circuit Breaker of fault breaking capacity 36

KA (ICS=100% ICU up to 433 V) completewith extended Rotary Mechanism and

Spreader Link Set with microprocessor release for O/L, S/C & E/F protection.- DG

1 Nos. 300 Amp. 415 volt AC 3 duty 4 pole contactor - 2nos

1 No. 300 A 415V, AC , 4P Manual Changeover with Operating Handle

Auto/Manual/Test/Off selector switch

2 Nos. over voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay.

3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for

Energy analyser unit to indicate current voltage frequency power factor and KWH

Indicating lamps for load on mains and load on set

Fuse for instruments

Battery charger, complete with transformer/rectifier, D.C. voltmeter and ammeter,

selector switch

Main supply for trickle,

failure monitor off and boost and current adjustment.

Supply Failure Timer

Restoration Timer

Control unit with three impulse automatic engine start/stop and failure to start lockout

Impulse counter with locking and reset facility.

ON/OFF/Control circuit switch with indicator

Audio/Video annunciation for.

4 Digitally signed by AMIT

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

TPN aluminum bus bars of minimum of 250 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -2 Nos.

(b) 40 Amps, TPN, MCB - 6 nos

Panel complete as above Each 2 225000.00 450000.00

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2

16 2.21 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour on Nos. 2 269.00 538.00

front side as required

MR Supply, Installation, Testing and Commissiong of 10 KVA True Online UPS 3 Phase Input -

3Phase Output in Parallel Redundant N+1 Configuration IGBT Based Rectifier and IGBT

Based Inverter Batteries:12 V, SMF Amararaja/Exide with minimum VAH capacity of 15600

suitable for 15 minutes backup with each ups Along with Accessories Rack, Interlinks, SFU,

17 Parallel Kit, DC Cable Upto 5 Meters complete in all respect as per the directions of the Nos. 2 407100.00 814200.00

engineer in charge. UPS should have availability of Input /Output isolator, Inbuilt manual

bypass along with phase sequence corrector. UPS Efficiency shall not be less than 94% from

25% to 100% Load

Total of Electrical items 2587514.00 1732222.11

5 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR HVAC TOTAL TOTAL

S No 2019/DSR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

EM 2018 DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,

having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors

for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as

1 1.0 required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C per HP 82 16415.00 1346030.00

ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3

Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER

not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity 4-way flow

VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable

media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed

motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain

2 2.0 pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for

single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have

automatic force shut down provision in case of fire on receiving signal from BMS System.

The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature.

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High

wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low

noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil,

electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary

3 3.0 accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply,

complete as required. The unit shall have automatic force shut down provision in case of fire

on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

Digitally signed by AMIT

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T"

4 4 Joints i.e. Refnet Joints/ Header with Insulation for refrigearnt piping

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen

testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF

system, complete with fittings, with suitable adjustable ring type hanger supports,

jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with

Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness

as given below for Suction and Liquid lines, all accessories as per specifications etc. as

5.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 120 245.00 29400.00

5.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 340 331.00 112540.00

5.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 120 466.00 55920.00

5.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 340 588.00 199920.00

5.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60 707.00 42420.00

5.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60 865.00 51900.00

5.7 5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 40 1022.00 40880.00

5.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 40 1108.00 44320.00

5.9 5.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 5 1170 5850

6 5.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 5 1230 6150

6.1 5.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 5 1265 6325

6.2 5.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 5 1309 6545

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC

conduit as required.

Supply,installation,testing and commissioning of PVC drain water with necessary clamps,

fittings such as bends tees etc. and duly insulated.

Digitally signed by AMIT

Supply, Laying, Termination of ISI Certified 4 Core 1.0 sq.mm ATSC, FRLS ,PVC insulated,

Unarmored, Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable

10 MR with proper ferrules, lugs and other necessary accessories. The spec shall meet the system Rmt 480 280.00 134400.00

manufacturer specifications.

Total HVAC WORKS 2890668.00 544724.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO DSR/MR Description Unit QTY Rate DSR AMOUNT NON DSR AMOUNT

Supply, Installation, Testing and Commissioing of LED Pendant luminaire with

LED(Light Emitting Diode) system power: 28W, 120 LM/W system efficacy,

colour temperature of 4000K, neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, CRI>80,

luminous flux of 3360 lm, MacAdam 3, T.H.D≤10%, driver efficiency ≥ 88%,

surge protection of 2.5kV, direct light emission, Aluminium body, polyester

1 MR white powder coat applied over a 5-stage pre-treatment, Prismatic diffuser for no 122 5195.00 633790.00

glare-free uniform light, UGR<19, Electronic control gear

Protection class I, IP40, L =1195mm, B = 295mm, H = 67mm, PH = 1500mm

Supply, Installation, Testing and Commissioing of Recessed downlightwith

HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system

power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy,

Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours; energy-efficient

LEDs, direct light emission, housing in die-cast aluminium, Polyester powder

2 MR white coloured coat applied over a 5-stage pre-treatment trim, prismatic no 67 1394.00 93398.00

diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear,

Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm

Supply, Installation, Testing and Commissioing of Pendant/Recessed luminaire

with LED (Light Emitting Diode), system power 28 W, luminous flux of

luminaire 3080 lm, 110 LM/W system efficacy, direct light emission CRI>80,

colour temperature of 4000K, Neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, luminaire

profile in aluminium, Plastic moulded end caps, Polyester powder Aluminium

white coloured coat applied over a 5- stage pre-treatment, high efficiency glare-

3 MR free snap fit micro-prismatic diffuser for homogeneous light distribution, ZHLS no 12 4001.00 48012.00

(Zero Halogen Low Smoke) internal wiring, integral Electronic control gear,

adjustable suspender, including cost of all connectors to create continuous

cascading effect.

Protection class I, IP 20, L = 1199 mm, B = 75 mm, H = 90 mm, PL max =

1 Digitally signed by AMIT

Supply, Installation, Testing and Commissioing of Pendant/Recessed luminaire

with LED (Light Emitting Diode), system power 14 W, luminous flux of

luminaire 1500 lm, 110 LM/W system efficacy, direct light emission CRI>80,

colour temperature of 4000K, Neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, luminaire

profile in aluminium, Plastic moulded end caps, Polyester powder Aluminium

white coloured coat applied over a 5- stage pre-treatment, high efficiency glare-

free snap fit micro-prismatic diffuser for homogeneous light distribution, ZHLS

(Zero Halogen Low Smoke) internal wiring, integral Electronic control gear,

adjustable suspender, including cost of all connectors to create continuous

cascading effect.

Protection class I, IP 20, L = 599 mm, B = 75 mm, H = 90 mm,

Supply, Installation, Testing and Commisioning of Recessed downlight with

LED (Light Emitting Diode) system power: 5W, Luminous flux of luminaire 400

lm, Colour temperature of 4000 K, Warm white, CRI > 80, 230V constant

current driver, 70% of luminous flux after 50,000 operating hours; energy-

efficient LED, direct light emission, housing in die-cast aluminium, Polyester

powder white coloured coat applied over a 5-stage pre-treatment ceiling trim,

with reflector, beam angle of 24°, Electronic control gear,

Protection class II, IP 20,

Supply, Installation, Testing and Commisioning of Recessed with trim luminaire

with Pinspot light with LED(Light Emitting Diode) system power:

luminous flux of luminaire 640lm, colour temperature of 4000K,

CRI > 90, SDCM<3, THD<10%, 230V constant current driver,

6 MR 70% of luminous flux after 50,000 operating hours, direct light no 4 2400.00 9600.00

emission, aluminium housing with trim, polyester Black powder

coat applied over a 5 stage pre-treatment on trim, with lens and

a beam angle of 36° and external Electronic control gear

Protection class II, IP20

SITC of Strip Light LED 5W per meter

2 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - FIRE ALARM

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

Supplying, installation, testing & commissioning of intelligent analog addressable

1 17.2.4 photothermal detector complete with mounting base complete as required. No 41 2858.00 117178.00

Supplying, installation, testing & commissioning of response indicator on surface/recessed

MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector

with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as

Supplying, installation, testing & commisssioning of intelligent addressable programmable

5 17.2.6 sounder complete as required. No 2 2651.00 5302.00

Supplying, installation, testing & commissioning of addressable manual call point complete as

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed

7 17.5.2 copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath Mtr. 420 173.00 72660.00

complete as required

Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power Battery

backup complete as required.

TOTAL FIRE ALARM & PA WORKS 236544.00 11610.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL

MR AMOUNT AMOUNT

DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

18.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the

wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel

paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

18.21 quartzoid bulb type sprinklers of rating 68 degree

2 centigrade with required accessories :

18.21.1 Pendant type 96 Each 522.00 50112.00

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with maximum

working pressure of 175 PSI test pressure of 875 PSI

3 18.25 (Burst) with branch line (Inlet) 25mm NPT male thread

to sprinkler head (Outlet) 15mm NPT female thread with

reducer, nipple, 2 side brackets, center bracket,

stockbar of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire

4 Extinguishers complete with all accessories as per

manufacturer's specifications.

Digitally signed by AMIT

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 3 NOS 12912.00 38736.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: IT

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S No Description UNIT QUANTITY RATE

A. UTP Components for Data DSR (INR) NON-DSR (INR)

Supply, Fixing & Laying of CAT 6A UTP cable 23 AWG solid copper

1 conductors for Connectivity of Hub room to End Point.High Speed Gigabit Mtr 6030 58.00 349,740.00

Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6A cable

termination at Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply , Installtion , Testing and Comissioning of CAT6A patch cord 2 Mtr (7

3 feet) for information outlet (I/O) to end user device connectivity.High Speed Nos. 201 350.00 70,350.00

Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of CAT6A patch cord 1 Mtr (3

4 feet) for information outlet (I/O) to Rack End Redantant device Nos. 201 279.00 56,079.00

connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of 24 port Loaded Jack Panel

for CAT6A cable termination at rack end. Data Active

C. Backbone Component

6 SITC of Multimode Fiber Patch Cord Nos. 1 950.00 950.00

Network Rack and Other Accessories

SITC of 64U Rack Floor Mount with wheels

SITC of router with Aggregate Throughput (Default) 100mbps, Aggregate

8 Throughput (Performance License) 500Mbps, Total onboard WAN or LAN Nos. 1 150,000.00 150,000.00

10/100/1000 ports 2nos, RJ-45-based ports 4nos, SFP-based ports 2nos,

SITCslots 2nos, Default

of Access Switch memory DDR3 of

with minimum ECC DRAM

24x (data plane)

10/100/1000 2gb,ports, 4x

10 Gig SFP+ ports for uplink ports(supporting Single mode & Multi mode

SITC of(LX, LR, SX &

Hardware SR modules).

controller Should

managed have Non-blocking

Indoor Wi-Fi Accessswitch

Adapter for power supply

SITC of 1 Gig SR transceivers/equivalent LC connector MM

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: CCTV

Sr No Item Description UoM Rate Total Amount

Sr No Item Description UoM Rate Total Amount

SITC of 2MP, 1/2.8” CMOS image sensor, low illuminance, high image

definition, Outputs 2MP (1920 × 1080) @ 25/30 fps Built-in IR LED,

max IR distance: 30 m, Intelligent detection: Intrusion,

tripwire,Abnormality detection: Motion detection, video tampering, no

SD card, Supports max. 256 GB Micro SD card, IP67, IK10 protection

etc all complete.

SITC of 8 channel Smart H.265+/H.265/Smart H.264+/H.264/MJPEG

decoding format. · Max. decoding capability: 32 × 1080p@30 fps or 32

× 2MP@30 fps. · Max. 384 Mbps incoming/recording/outgoing

bandwidth. · Support AcuPick with Max. 16-Channel. · Support N+M

2 cluster. · AI by recorder: 2-channel face detection and recognition, 4- No's 1 11,845.00 11,845.00

channel perimeter protection, and 8-channel SMD Plus. · AI by camera:

Face detection and recognition, perimeter protection, SMD Plus,

metadata, ANPR, stereo analysis, heat map, and people counting etc

3 SITC of Hard Disk 16TB required for the above NVR etc all complete. No's 1 47,855.00 47,855.00

4 CAT6 Patch Chord in existing Network Rack No's 6 5,800.00 34,800.00

5 CAT6 IO / Connector at camera location No's 6 5,000.00 30,000.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: IPBAX

S No Item Description UoM Qty Rate DSR Amount Non DSR Amount

1 SITC of EPABX Intercom with 4 incoming lines and 128 Anolog Extensions complete in all respect Nos 1 110,000.00 110,000.00

2 SITC of Analog Phones Nos 87 1,500.00 130,500.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: Audio Visual

Unit rate Total

Sr No Item Description UoM

SITC of Cable Cubby with flip top, cover and 6 Pass

Through Holes for multi-format cables, 2 Universal Power

Socket , 1 HDMI, 1 USB-C for Data Transfer, made of

aluminium etc all complete etc all complete

SITC of 2m/6.5ft HDMI 2.0 Cable, 18Gbps 4K60Hz, Dolby

2 Vision & HDR, ARC,CEC, ALLM, VRR, | CL3 & VW-1 Rated No's 5 3,175.00 15,875.00

etc all complete

SITC of10m HDMI 2.0 AOC | 24Gbps | 4K60Hz | Dolby

3 Vision & HDR | ARC, CEC, ALLM & VRR | ISF Certified | FT4, No's 1 13,750.00 13,750.00

CL4 etc all complete

SITC of 2m/6.5ft USB-C to C Cable | SuperSpeed USB

20Gbps | 4K60 Alt-Mode | 100w PD etc all complete

5 SITC of Various Cables & Connectors etc all complete No's 1 11,950.00 11,950.00

Total 98,550.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES-ART WORKS

S NO MR DESCRIPTION UNIT QUANTITY RATE

DSR (INR) NON DSR (INR)

Providing and fixing theme artwork/ any other as per direction and

site requirement from the local artisans as per the selection of the

1 MR client and the architect.

Panels of various sizes No. 15 3000.00 45000.00

TOTAL ART WORKS 0.00 45000.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FURNITURE

DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

TABLE FOR ZONAL / REGIONAL MANAGER

TABLE- W 2300 x D 1000 x H 750mm SIDE TABLE- W 1400 x D 550 x H 750mm

Main Table: The table top dimensions will be 2300x 1000x750 mm made in PLB (Pre laminated Fibreboard)

with the density of 680kg/m³ and 25mm thick one side pre-laminate board confirming to IS-14587:1998.

Surface: CPL (continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be

confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

12823:1990. 2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The edge band

material should have Shore D hardness of 79± 4. The Hot melt glue used for fixing the PVC edge band

should have ISO 9001- 2015 quality certification confirming to ASTM D 4499 standards for viscosity and

thermal stability. The top surface will have 30 mm aluminium channel ( Z Section) all round the main table at

the edges below the top surface. There will be a support pedestal extended by 200 mm on the right side

below the main table thus achieving over all dimension of 2300 x1000 mm.

The return table will be 1300x550 mm in PLB confirming to IS- 14587:1998. Surface: CPL( continuous

pressure laminate) in 0.5mm thickness. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003

standards and approved shade confirming to IS-12823:1990. 2 mm thick PVC edge band confirming to DIN

68861 for resistance to clearers. The edge band material should have Shore D hardness of 79± 4.. The hot

melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification confirming to

ASTM D 4499 standards for viscosity and thermal stability. The return table will be connected to the main

table by structurally engineered MS connector of thickness 2mm which has undergone zinc passivation

confirming to IS:1573 – 1986. Two connectors will be used.

Support bracket: The main table and the return table will be supported by 130 mm high aluminium die cast

structural bracket designed in “V” shape to withstand at optimum load, made in LM6 (Al-Si12 - EN1706 AC-

44100), confirming to BS 1490:1988 LM6, The structural bracket will have suitable design to rest on the

support pedestal and the Gable End panel. The aluminium bracket will be powder coated as per the

approved colour. The aluminium bracket should undergo 7 step rust resistance pre treatment process viz

degreasing, pickling as per IS standard.

Modesty panel: The table will be provided with Modesty panel connecting the support pedestal and the

gable end- size 1420x 450 mm. The modesty will be made in PLT(laminated both sides) 18 mm thick

confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

12823:1990. The modesty have 2 mm thick PVC edge band confirming to DIN 68861 for resistance to

clearers. The edge band material should have Shore D hardness of 79± 4.

Support pedestal: The support pedestal size 600(W) x 850(D)x 590(H)will be made in PLB confirming IS-

14587:1998. The PLB will be 25 mm thick PLT. Pedestal construction will be in three equal drawer box

construction made in 12 mm PLT in black finish . Drawer facia will be made of 25mm thick PLB one side pre-

laminate board confirming to IS-14587:1998. Drawer telescopic channel will have extension of 450 mm with

silver anodised finish. The slides will be cycle tested to BIFMA standards- minimum 50000 times .

Gable End: The under structure will have on one side gable end support 50 mm thick in PLT(Laminated

both sides) confirming to E-1 grade as per IS- 12823:1990. The 50 mm thick Gable end shall comprise of 25

mm PLT + 25 mm PLB as per IS: 12823. The edges will have 2 mm PVC edge band confirming to DIN

68861 for resistance to clearers. The edge band material should have Shore D hardness of 79± 4.. The hot

Digitally signed by AMIT

HIGH BACK CHAIR FOR REGIONAL MANAGER

SPECIFICATION:-

Seat is made out of 9 layer 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-

nuts and revited in to the wood.Gaslift - Class 4

tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm dia castors compling to ANSI /

BIFMA X 5.1 – 2002.Specially designed metal base 5 pronged structure forged out of CR Sheets of 2 mm

thick. Base of diameter 26 inches for complete stability, extreme durability, sturdiness and pleasant

aesthetic looks. Reinforced with CO2 welding to provide additional strength and support. Tested prudently

and rigorously as per ANSI/BIFMA X5.1-2011

General Purpose Office Chair Standards.Upholstery: Cushion with pre moulded foam of 50 - 60 density in

the shape of plywood with leatherette tapestery. Density -- 52 kg/m3 / Hardness -- 12.6kgf at

2 25%.Distinctively and characteristically designed tilt mechanism offering a very smooth and fluidic reclining 2 NOS ₹ 24,022.80 ₹ 48,045.60

with tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back

support.Multilock mechanism is fabricated from CR Sheets, undergo through CO2 welding process

imparting uniform surface finish and tensile strength. The components are processed with high degree of

precision and care so as to assemble with other parts in perfect harmony to give smooth and effortless

reclining experience. Tension springs are made out Grade II material conforming to Indian Standards. Also

provided with release levers for lockingmechanism and height adjustment of seat. Mechanism aides to

operate the height adjustment, and has been equipped with 4 locking positions,

back rest “ Return Prevention” function .Cusioned Back with Leatherette tapestery used for back upholstery

With Unique Dynaflex Two Piece Back Construction , Dya Flex provides a comfotable cushioning that

stimulates the spine & abdominal muscles to promote a healthy posture & back . Inbuilt body flex lumbar

VISITOR CHAIR FOR ZONAL / REGIONAL MANAGER

Supply and Placing in position of Visitor Chairs of approved make. The seat is cushioned seat made of injection molded

plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density

45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The

back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm,

3 upholstered with leatherette. The back size is 47.7 W cm x 60.1 D cm. The tubular frame is cantilever type and made of 6 NOS ₹ 14,910.30 ₹ 89,461.80

Ø2.54±0.03cm x 0.2±0.016 cm thick SS 202 tube. The back connected to frame through chrome plated high pressure die

casted connector pipe. All the dimensions will be as per the Original Manufacturer's Specifications. The product should be of

BIFMA compliance, ISO 9001:2015 and ISO 14001:2015 complete as per approved sample and as per the direction of

EngineerIn-charge.

SOFA 3-SEATER FOR REGIONAL MANAGER

SPECIFICATION:-

Seat Foam: the sofa is made up of fine quality leatherette.The structure is made up of silver wood and pine

wood.The Seat is made of PU Foam with Density 32 to 40 +/- 2 kg/cu .mtr Seat is upholstered wuth

4 Leatherite.Back Foam: The Back is made of PU Foam with Density 32 to 40 +/- 2 kg/cu, Backis upholstered 2 NOS ₹ 53,015.40 ₹ 106,030.80

with Leatherite.Unterstructure is made up of silver wood or pine wood , 4mm Dia zigzag Spring is mounted in

the understructure for support and additional cushioning purpose. Legs should be made up of solid wood

having pu matt finish.

Digitally signed by AMIT

TABLE FOR ASSISTANT MANAGER

TABLE SIZE: 1350W X 600D X 750HT

Specifications:

MAIN TABLE:- The main table shall be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998.

Soft closing access flap with in-built power box to be provided on work surface for wire management. Return table Work

Surface should be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998. PLB will be E1-P2

grade and approved shade. Confirming to IS-12823:1990. 2 mm thick PVC edge band will confirm to DIN 68861 for

resistance to clearers. The edge band material should have Shore D hardness of 79± 4. The Hot melt glue used for fixing the

PVC edge band should have ISO 9001- 2015 quality certification confirming to ASTM D 4499 standards for viscosity and

thermal stability. The edges should be PVC Edge banded with matching finish or have an option of reverse water fall

edges.Modesty Panel shall be made of 18mm thick PLT both sides pre-laminate board confirming to IS-14587:1998.The

height of modesty shall be 450 mm.The modesty panel will be connected to the main table by 2 nos special Aluminum

extruded brackets. The modesty will be fixed 150 mm from the edge of the table.

Wire Management:Continuous PVC Cable Tray with provision to mount switches and sockets as per client requirement.

Vertical wire entry cover for wire uptake from floor to cable tray and 300mm Aluminium Flip Up for swicth access.

Legs and Supports:- The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor

undulations- +/- 20 mm. ERW Tube confirming to IS 4923 : 1997 – 16g. Main leg members will be connected through a

horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the horizontal

tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using

Argon & Co2 gas mixture on a Robotic welding machine to ensure adequate welding strength with consistency.• The legs will

be connected with Cross beams to take care of the bending stress catering up to 1800 mm length and up to 900 mm depth of

the work surface.

Finish:- All metal components & aluminum die cast parts will be powder coated by Nano ceramic surface treatment process

compiled to a Bend test-ASTM D3451 – 06, Adhesion -DIN EN 14901 Salt spray test- DIN EN ISO 9227, which is non-

hazardous, environmental friendly and will have uniform powder coating thickness of 50-60-micron thickness.

MOBILE PEDESTAL:-400W X 450D X 600HT The pedestal shall be made up of Pre-laminated particle board of grade II of IS

CUBICALS WITH TABLE AND SIDE STORAGE

CUBICAL SIZE:-2400W X 1500D X 1200HT

SIZE - 1800W X 750D X 750HT

COM SIDE STORAGE - 900W X 450D X 750HT

MAIN TABLE:- The main table shall be made of 25mm thick PLB one side pre-laminate board confirming to IS-

14587:1998. Soft closing access flap with in-built power box to be provided on work surface for wire management.

Return table Work Surface should be made of 25mm thick PLB one side pre-laminate board confirming to IS-

14587:1998. PLB will be E1-P2 grade and approved shade. Confirming to IS-12823:1990. 2 mm thick PVC edge

band will confirm to DIN 68861 for resistance to clearers. The edge band material should have Shore D hardness of

79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification

confirming to ASTM D 4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded

with matching finish or have an option of reverse water fall edges.Modesty Panel shall be made of 18mm thick PLT

both sides pre-laminate board confirming to IS-14587:1998.The height of modesty shall be 450 mm.The modesty

panel will be connected to the main table by 2 nos special Aluminum extruded brackets. The modesty will be fixed

150 mm from the edge of the table.

Wire Management:Continuous PVC Cable Tray with provision to mount switches and sockets as per client

requirement. Vertical wire entry cover for wire uptake from floor to cable tray and 300mm Aluminium Flip Up for

Legs and Supports:- The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor

undulations- +/- 20 mm. ERW Tube confirming to IS 4923 : 1997 – 16g. Main leg members will be connected

through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical

and the horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg

will be fabricated using Argon & Co2 gas mixture on a Robotic welding machine to ensure adequate welding strength

Digitally signed by AMIT

HEAD CHAIR FOR CUBICALS AND CONSULTANT

Chair's Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and

revited in to the wood.Gaslift - Class 4 tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm dia castors

compling to ANSI / BIFMA X 5.1 – 2002.The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced

with bottom ribbing for additional buttress and strength.Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011

General Purpose Office Chair Standards.Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density -- 52

kg/m3 Hardness -- 12.6kgf at 25%.This mechanism is manufactured out of cold Rolled Carbon Steel IS 513-1994 Sheets,The

7 steel components are manufactured with highly precision tools For accuracy in matching other parts for smooth functioning. 13 NOS ₹ 12,800.00 ₹ 166,400.00

The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher tensile

strength. Springs are made out of Grade II material. Composite release levers for locking mechanism & Gas lift height

adjustment. Release lever mechanism for Locking and Gas lift height adjustment. Back Frame is upholstered with Thinner

Mesh Adjustable Lumbar Support Allows you to adjust the lumbar support position for good back support and blood

circulation.Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable -

Height Adjustable.Chair will have adjustable headrest. Tension control is below the Seat.Seat are duly upholstered with

approved fabric. Chair Should be BIFA Certified.

VISITOR CHAIR FOR CUBICALS AND CONSULTANT

Medium back Visitor chair Seat is made out of 9 layer 12mm molded hot pressed plywood in ergonomic shape fitted with

Imported T-nuts and revited in to the wood.Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose

Office Chair Standards.Back Frame is upholstered with Thinner Mesh Adjustable Lumbar Support Allows you to adjust the

8 lumbar support position for good back support and blood circulation.Moulded self skinned polyurethene Arms confirming to IS 28 NOS ₹ 10,000.00 ₹ 280,000.00

7078 with steel insets for long life.The steel components are fabricated by using Co2 welding process for giving uniform

surface finish with higher tensile strength. Springs are made out of Grade II material.Fixed steel base of 25mm dia pipe of 1.5

mm thickness with Chrome with PVC shoes.Chair dimensions should be Width- 63.5 cm ,Depth- 57 cm , Height- 86 cm,Width

(Arm to Arm)- 46 cm ,Seat Depth- 49 cm Width- 49.5 cm. Chair Should be BIFMA Certified.

WORKSTATIONS WITH PEDESTAL

Table Top - All table tops will be made out of PLB will be E1- P2 25mm Pre-laminated particleboard (PLB) confirming to IS-

12823:2018 with 2 mm PVC edge banding. The table top will be made in PLB( Pre laminated board) with the density of

680kg/m³ and 25mm thick one side pre-laminate board confirming to IS-12823: 2018. Surface: CPL( continuous pressure

laminate) in 0.5mm thickness in melamine finish. The PVC edge band will be confirming to to IS 4892 standards. Edge band

used have good resistance to light fastness, impact resistant and highly resistant to heat and solvents.2 mm thick PVC edge

band will confirm to DIN 68861 for resistance to clearers. The edge band material should have Shore D hardness of 79± 4.

The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification confirming to ASTM D

4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded with matching finish or have an

option of reverse water fall edges.

Support - The PLB Gable end supports are offered in both 18 mm PLT (laminated in the same finish both sides). The PLB will

be confirming to IS 12823 : 2018. MS leg support should confirm to IS 4923 : 1997, IS 3074.

Wiremanagement - Cable management.The system should have effective Cable management system. The data and the

power cables should be at different levels (called Raceways) to maintain the separations as per the IT norms minimum 300

mm apart. The wire management slots in the frames are large enough to manage high volume of data cables (CAT-6) -

approx- 40-50 CAT-6 cables. Vertical movement of the cables in addition to the two/ three levels of horizontal passage should

be possible. The raceway covers should be designed as “clip on” raceway which permits easy removal and fixing. No

screws/nut bolt should be used. The Skirting raceways are 120 mm and the raceways at the table top level are of 120 mm.

Digitally signed by AMIT

screws/nut bolt should be used. The Skirting raceways are 120 mm and the raceways at the table top level are of 120 mm.

The length of the raceways will be matching to the frame width. All standard electrical/Data faceplates should be capable of

being be mounted on the raceways at both the levels. The raceways will be provided with cut outs as per the requirement of

9 the switches/sockets. The switches /sockets to fixed fixed “staggered” to ensure electrical safety. Option of additional raceway

should be available to accommodate more cables (if >50 CAT-6 cables) or sockets.

PARTITION:-The partition based system will be with main spine in 50 mm thick made by 1,2 mm thick CRCA sheet confirming

to IS 513: (2008), IS 13871:1993. The end and intermediate spines could be 50 mm or with an option of 33 mm thick. The

profile of verticals should be able to slide the tiles thickness of 6 mm. The verticals will have multiple slots for carrying the

data and power cables and provision for fixing MS brackets.There will be minimum three slots at different levels to

accommodate raceways at skirting and table top levels. There should be options of carrying the cables both above and

below the table top as per the requirement. The slot provided should be of size- 150x 25 mm. the slot cut out should made by

CNC machines to avoid sharp edges and burr. There will be minimum four horizontal members in each frame- top , middle

levels and at the skirting level. The horizontal members will be made from CRCA sheets formed in “C” shape in hydraulic

press. The CRCA sheets will be confirming to IS 513: (2008), IS 13871:1993.All the Frames are duly powder coated in

charcoal black color or color of choice to a thickness of 50-60 microns confirming to ASTMB – 117, ISO – 1520 and ISO –

1518 & ASTMD - 2794. The powder coating will be done with NANO Ceramic coating.All the Frames are duly powder coated

in charcoal black color or color of choice to a thickness of 50-60 microns confirming to ASTMB – 117, ISO – 1520 and ISO –

1518 & ASTMD - 2794. The powder coating will be done with NANO Ceramic coating.

Workstation is provided with Fabric Magnetic, Glass Marker and Laminate tile.

• Glass Marker tiles: 5mm Glass with white Vinyl Backing. The glass will confirm to ASTM C1036.

• Laminate Tile: Constructed out of 6mm thick Pre-laminated Particle board confirming to IS – 12923.

• Fabric Tile: Constructed out of 5.5mm thick Medium Density Fiber Board (MDF) confirming to IS – 12406 and covered with

Fabric of choice. The fabric used will be confirming to BS EN 1021-1, BS 7176 & ISO 105-B02. The glue used for upholstery

are made with advanced adhesives confirming to ASTM D 1500, ASTM 1298 standards. Sprayed with upgraded machines to

ensure uniformity and best adhesion.

Magnetic tile: Constructed out of 0.8mm Galvanized sheet confirming to IS 277, ASTM A653 specifications. Sheets are post

L-SHAPE WORKSTATION

CHAIR FOR WORKSTATIONS

Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited

in to the wood.Gaslift - Class 4 tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm dia castors

compling to ANSI / BIFMA X 5.1 – 2002.The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced

with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011

10 General Purpose Office Chair Standards.Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of 67 NOS ₹ 9,261.00 ₹ 620,487.00

plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25%.Self Calibrating Multilock Mechansim Tested as per BIFMA

Standards.Back Frame is upholstered with Thinner Mesh Adjustable Lumbar Support Allows you to adjust the lumbar support

position for good back support and blood circulation.Moulded self skinned polyurethene Arms confirming to IS 7078 with steel

insets for long life. one way adjustable - Height Adjustable.Chair should have Adjustable Headrest.Tension control is below

the Seat.Seat are duly upholstered with approved fabric.hair Should be BIFA Certified.

Digitally signed by AMIT

CONFERENCE TABLE

OVERALL SIZE - 4800W X 1800D X 750HT

MAIN TABLE SIZE - 1800W X 750D X 750HT(QTY-01)

SIDE TABLE SIZE - 1350W X 600D X 750HT(QTY-06)

Specifications:

Conference table in completely knock down conditions that is to be assembled at site. The construction of the main table shall

be with minifix dowels, pins and MS brackets. table tops will be made out of PLB will be E1- P2 25mm Pre-laminated

particleboard (PLB) confirming to IS-12823:2018 with 2 mm PVC edge banding. The table top will be made in PLB( Pre

laminated board) with the density of 680kg/m³ and 25mm thick one side pre-laminate board confirming to IS-12823: 2018.

Surface: CPL( continuous pressure laminate) in 0.5mm thickness in melamine finish. The PVC edge band will be confirming

to to IS 4892 standards. Edge band used have good resistance to light fastness, impact resistant and highly resistant to heat

and solvents.2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The edge band material should

11 have Shore D hardness of 79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality 1 NOS ₹ 128,561.00 ₹ 128,561.00

certification confirming to ASTM D 4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded

with matching finish or have an option of reverse water fall edges.

Support - The PLB Gable end supports are offered in both 18 mm PLT (laminated in the same finish both sides). The PLB will

be confirming to IS 12823 : 2018. MS leg support should confirm to IS 4923 : 1997, IS 3074.The table top shall be supported

on particle board base gable end. The end and mid wall of the table on the side shall be topped by gable end. It should be

made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge

banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty

panel shall be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. Wire

carrier shall be provided below the table top for power connection having size 60mm X 125mm made of 0.8mm thick high

yield strength of CRCA sheet of grade 'D' confirming to IS:513 with duly powder coated. There shall be buffers provided at the

base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in

between. meeting long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending

CONFERENCE TABLE

OVERALL SIZE - 10200W X 1800D X 750HT

MAIN TABLE SIZE - 1800W X 750D X 750HT(QTY-01)

SIDE TABLE SIZE - 1350W X 600D X 750HT(QTY-14)

Specifications:

Conference table in completely knock down conditions that is to be assembled at site. The construction of the main table shall

be with minifix dowels, pins and MS brackets. table tops will be made out of PLB will be E1- P2 25mm Pre-laminated

particleboard (PLB) confirming to IS-12823:2018 with 2 mm PVC edge banding. The table top will be made in PLB( Pre

laminated board) with the density of 680kg/m³ and 25mm thick one side pre-laminate board confirming to IS-12823: 2018.

Surface: CPL( continuous pressure laminate) in 0.5mm thickness in melamine finish. The PVC edge band will be confirming

to to IS 4892 standards. Edge band used have good resistance to light fastness, impact resistant and highly resistant to heat

and solvents.2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The edge band material should

have Shore D hardness of 79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality

certification confirming to ASTM D 4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded

with matching finish or have an option of reverse water fall edges.

Support - The PLB Gable end supports are offered in both 18 mm PLT (laminated in the same finish both sides). The PLB will

be confirming to IS 12823 : 2018. MS leg support should confirm to IS 4923 : 1997, IS 3074.The table top shall be supported

on particle board base gable end. The end and mid wall of the table on the side shall be topped by gable end. It should be

made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge

banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty

panel shall be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. Wire

carrier shall be provided below the table top for power connection having size 60mm X 125mm made of 0.8mm thick high

yield strength of CRCA sheet of grade 'D' confirming to IS:513 with duly powder coated. There shall be buffers provided at the

base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in

between. meeting long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending

tested as per Indian standard. Product should be BIFMA Compliance.

Digitally signed by AMIT

MEETING ROOM TABLE CIRCULAR

SIZE:-1350MM@DIA X 750HT

SPECIFICATION:-

Table top - The work surface will be in PLB 25mm thick one side pre-laminate board confirming to IS-

14587:1998. The density of PLB will be 680kg/m³. Surface: CPL( continuous pressure laminate) in 0.5mm

thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards

and approved shade confirming to IS-12823:1990.PVC edge band will be minimum 2 mm thick, will be

imported, quality confirming to DIN 68861, 53388 standards. The edge band will be fixed to the work surface

edges all round with Imported Hot melt Glue confirming to ISO 9001- 2008 and certified by ANSI for quality.

Under Structure - • The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater

for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 : 1997 – 16g. Main leg members will be

13 connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 1 NOS ₹ 15,139.80 ₹ 15,139.80

4923: 1997. The vertical and the horizontal tubes will be welded with CO2 MIG welding process confirming to

IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic welding

machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross

beams to take care of the bending stress catering.• The number of cross beams will be based on the depth

of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16 g.

• The Engineering plastic components will be made with Acrylonitrile butadiene styrene (ABS) which are

confirming to ASTM D256 for Izod Impact (1/4”) for Leg shoe and levelers.

Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.Cable Trays

will be provided when the cable access is required from the top through ‘Flip ups”. The Switch/socket slots

are provided as a part of the “Flip Up” design just below the flip covers.

The “flip up” should be made in aluminum flip covers with soft closing arrangement. The “Flip up” cover will

FOR CONFERENCE ROOMS

Chair's Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and

revited in to the wood.Gaslift - Class 4 tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm dia castors

compling to ANSI / BIFMA X 5.1 – 2002.The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced

with bottom ribbing for additional buttress and strength.Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011

General Purpose Office Chair Standards.Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density -- 52

kg/m3 Hardness -- 12.6kgf at 25%.Distinctively and characteristically designed tilt mechanism offering a very smooth and

fluidic reclining motion with tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back

support.Multilock mechanism is fabricated from CR Sheets, undergo through CO2 welding process imparting uniform surface

14 finish and tensile strength. The components are processed with high degree of precision and care so as to assemble with 52 NOS ₹ 11,000.00 ₹ 572,000.00

other parts in perfect harmony to give smooth and effortless reclining experience. Tension springs are made out Grade II

material conforming to Indian Standards. Also provided with release levers for locking mechanism and height adjustment of

seat. Mechanism aides to operate the height adjustment, and has been equipped with 4 locking positions, back rest “ Return

Prevention” function. Back Frame is inserted with Mesh & Adjustable Lumbar Support.Tension control is below the

Seat.Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long Moulded self skinned polyurethene Arms

confirming to IS 7078 with steel insets for long life. one way adjustable - Height Adjustable.Seat is duly upholstered with

approved fabric.Chair Should be BIFA Certified.Seat: Depth- 51.5 cm Width- 44.5 cm

Width- 51.5 cm Depth- 53.5 cm Minimum Height- 99.5 cm Maximum Height- 108.5 cm Minimum Seat Height- 44.5 cm

Digitally signed by AMIT

TABLE SIZE: 1800W X 900D X 750HT

Specifications:

For Cafeterias - 18mm thk prelaminated Hydrosheild table top/ ISO Table top.

For Office / meeting tables - 25mm thk prelaminated particle board with 2mm edge banding finishSupport:

End Legs: Chrome Finished understructu

Chair is molded from GF 20% Polypropylene conforming to ASTM D 638 STD & Complying to ROHS. Seat &

back design will be integrated as a single unit. The chair shall be injection molded with 2500 tonnage press.

The chair should weigh about 3.9 kg. The back will be designed with triangular structural trusses & narrowed

at the top to provide strength & comfort to the chair with good air circulation to the user. The back should be

designed to provide ergonomic comfort with precise curvature to offer good lumbar support. The seat profile

should be designed with water fall to provide necessary comfort in popliteal region.

The design of the chair will be provided with four U shaped legs ensuring good strength to the chair. Chair

shall be tested for minimum load bearing capacity of 150 KG. The design should have the capability to

stack.Chair should be BIFMA and Green Guard certified.

RECEPTION TABLE

SIZE:-2400W X 750D X 1050HT

SPECIFICATION:-

17 RECEPTION TABLE with 900mm L Acrylic counter 1 NOS ₹ 111,522.60 ₹ 111,522.60

Specifications - Made up of prelam particle board

Prelam hanging drawer 2 Number

SOFA FOR RECEPTION

Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of

PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leatherette.Back Foam: The Back is

18 made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 1 NOS ₹ 23,793.00 ₹ 23,793.00

23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/-

0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and

additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

Digitally signed by AMIT

SOFA FOR RECEPTION

Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of

PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leatherette.Back Foam: The Back is

19 made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 2 NOS ₹ 39,482.10 ₹ 78,964.20

23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/-

0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and

additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

SOFA FOR RECEPTION

Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of

PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leatherette.Back Foam: The Back is

made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density

23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/-

0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and

additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

Center table with an overall size L 1200 X W 600 X H 425 mm. The top of the table shall be made up of

21 12mm thick toughened glass. The top profile shall be in square shape with bevelled edges. The top shall be 2 NOS ₹ 14,604.00 ₹ 29,208.00

supported on vacuum caps situated over SS 202 grade pipe frame. The under structure shall have SS with

shiny chrome finish pipe frame having dia. 20-25.4mm with 2mm thick. There shall be good quality PPCP

shoe provided to avoid scratches on the floor.Top glass is partial tempered glass.

Corner table with an overall size L 600 X W 600 X H 505 mm. The top of the table shall be made up of

22 12mm thick toughened glass. The top profile shall be in square shape with bevelled edges. The top shall be 3 NOS ₹ 9,808.00 ₹ 29,424.00

supported on vacuum caps situated over SS 202 grade pipe frame. The under structure shall have SS with

shiny chrome finish pipe frame having dia. 20-25.4mm with 2mm thick. There shall be good quality PPCP

shoe provided to avoid scratches on the floor.Top glass is partial tempered glass.

Digitally signed by AMIT

SPECIFICATION:-

The storage will be made in 18 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick

one side pre-laminate board confirming to IS 12406 : 2013. Surface: CPL ( continuous pressure laminate) in

0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003

standards and approved shade confirming to IS-12823:1990.The back of storage will be made in 9 MM PLB

(Pre laminated board) with the density of 680kg/m³ and 18 mm thick one side pre-laminate board confirming

to IS 12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm thickness in melamine finish.

Storgage will be provided with edge banding 2 mm thick PVC edge band will confirm to DIN 68861 for

resistance to clearers. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015

quality certification and confirm to ASTM D 4499 standards for viscosity and thermal stability. The edge band

material should have Shore D hardness of 79± 4. storage will have two adjustable shelves making 3

MEDIUM HT STORAGE

Digitally signed by AMIT

Schedule of Quantities: Signages

S No Description Unit Qty Unit price

1 RECEPTION 3D ACRYLIC SIGNAGE

Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of

required size and shape with arrangement of screws in the letters itself for

mounting on the walls or pasting using Tape. Fixing complete as per

directions of the engineer. The sizes would be calculated in Sqft as per Logo Each 1 25,624.00 25624.00

Design provided.

Tentative Size 42"x60"

2 NAME SIGNAGE CHANGEABLE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with textured

wood finish pasted /White milky acrylic 3mm laser cut pasted on top with

proper names/ Departments written using plottercut vinyl or laser cut acrylic

letters in approved colour.Inserting provision for changing names .Fixing Each 13 1,281.00 16653.00

provision using double sided tape as required.

Signage Size 12"x5"

3 TOILET ICONS

Providing and fixing of Acrylic signage made of 5mm Acrylic with textured

wood finish pasted /White milky acrylic 3mm laser cut pasted on top with

proper icons using plottercut vinyl or laser cut acrylic letter in approved colour. Each 3 1,025.00 3075.00

Fixing provision using double sided tape as required.

Signage Size :8"x8"

4 FIRE SAFETY SIGNAGE

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun board

sheet at base with photoluminescent film self adhesive & colored vinyl (

Red/Green) Plotter cut and pasted on top. Both side / Single Side facing

Complete including fixing on wall with screws and washers or hanging on

ceiling with GI chain/GI Bar complete as per technical specifications and

a directions of Engineer.

Photoluminescent, Fire Hose Reel - 10"x8" Each 1 384.00 384.00

b Photoluminescent, Fire Exit / Escape Sign - 18"x6" Each 1 384.00 384.00

c Photoluminescent, Floor Level - 18"x6" Each 1 384.00 384.00

d Photoluminescent, Fire Alarm Call Point - 10"x8" Each 1 384.00 384.00

e Photoluminescent, Fire do not use lift- 10"x8" Each 1 384.00 384.00

f Photoluminescent Signs, Fire Extinguishers - 10"x8" Each 3 384.00 1152.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: HORTICULTURE

S NO DESCRIPTION Qty Unit Rate DSR AMOUNT NON DSR AMOUNT

Supply and Planting Lolina plant having 2-3 ft height with Coco-

peat, mud and manure complete.

Supply and Planting Seaforthia Palm having ht. 90cm to 1.20 m

2 with 6-8 suckers, well developed, fresh and healthy lush green 10 Each 1500.00 15000.00

leaves from bottom to top complete.

Supply and Planting Rhapis Palm having ht. 90cm to 1.20 m with

3 15 to 18 equal suckers, well developed, full of fresh and healthy 10 Each 1500.00 15000.00

leaves from bottom to top complete.

Supply of full soil fill conical shaped planters of specified volume

and dimensions in stone finish or equivalent. planters to be

indigenously made by rotational moulding, with homogeneous

recyclable, industrial grade polymer-resin mix, and textured

surface. planters should have an integrated water outlet hole &

4 plug, single layered peel-proof construction, light weight, rust

proof, uv stabilized, anti-frost feature without any joints, and

easy to clean. planter supplier must give 1 year warranty against

any fading or cracking for both indoor and outdoor use. green

plant and laying is extra. potting instructions as per company

5 Artificial Vertical Garden on wall 10 Sqm 2562.00 25620.00

6.1 Supply and installation of Natural Plants with sand, fertilizer etc. 30 LS 500.00 15,000.00

Digitally signed by AMIT

Interior fit out works in the office space of AICL, Guwahati

S NO DESCRIPTION AMOUNT AMOUNT

2.00 SANITARY/ PLUMBING WORKS 0.00 21,802.00

3.00 ELECTRICAL WORKS 1,830,192.00 1,563,745.76

5.00 WI-FI & LAN WORKS (ACTIVE & PASSIVE) 0.00 1,536,255.00

8.00 FIRE ALARM SYSTEM 244,206.00 15,480.00

11.00 AV and VC Connectors and Cables only 0.00 120,745.00

Total (DSR +MR) 20,523,817.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

DSR ITEM NON DSR ITEM

1 FLOORING WORKS

VITRIFIED TILES : Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the manufacturer) with

water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick

11.41A cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white

1.04 cement and matching pigments etc., complete. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be

done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

Size of Tile 600x600 mm

VITRIFIED TILES : Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water

absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12

mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the

joint with white cement & matching pigments etc. complete.

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all

complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1

cement: 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with

pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the

11.51.1 Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. SQM 0.60 6,603.35 3,962.01

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness

1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement,

including cement slurry, but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 5.00 614.20 3,071.00

TOTAL FLOORING WORKS 89,445.66 38,570.00

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and

consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

2.01 12.45 perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all

as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but

12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) SQM 926.00 1,355.80 1,255,470.80

ACOUSTIC CEILING: Providing and fixing suspended Demountable acoustic ceiling in recessed grid system -Danoline: Belgravia 300

x 1200 x12.5mm E with Unity 3,square 3.5mm holes, with 0.80 NRC* Material: High Grade Glassfiber Reinforced Perforated

2.04 MR plasterboard with Cleaneo Technology Board type: Ceiling tile Length x width x thickness: 300x1200x12.5mm Edge: E recessed grid SQM 165.00 3,200.00 528,000.00

system (8mm recess)

Perforation: Unity 3, 3.5x3.5 Surface: Water-based acrylic paint ,Colour: White NCS 0701 Y24R, closet match to RAL 9003; gloss 5

Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

DSR ITEM NON DSR ITEM

TOTAL FALSE CEILING WORKS 1,255,470.80 528,000.00

3 WALL FINISHES WORKS

GLASS PARTITION (FIXED GLASS PARTITION WITH 10MM GLASS): Providing & Fixing of Modular Single glazed partitioning frame

make 45mm System, Using KL 45 001 (45mm x 25mm) as wall starter section, Using KL 45 001 & KL 45 002 (45mm x25mm) as Top

3.01 MR & bottom channel. Toughened Glass of thickness 10mm to be installed with required accessories ie glass to glass aluminium I SQM 30.00 4,400.00 132,000.00

sections, T section & 90 degree sections as per the requirement & Glass packing to adjust the floor level. Insertion of

silicon/Thermoplastic gasket to adhere the glass firm & airtight. Partition Height Considered is 2500mm

FRAMELESS HINGED GLASS DOOR: Providing & Fixing of Modular Aluminium single leaf Stile door frame of make 45 mm System

duly Anodized Aluminium Sections using KL 45 001 & KL 45 003 (45mm x 45mm) and Stile door of size 60x35mm as door frame with

3.02 MR Toughened Glass of Thickness 10 mm. Hardware as per make list and Lever Handle with Mortise Lock, Exposed Door Closer, Set of 4

Hinges, Door Stopper and required accessories ,Silicone/Thermoplastic Gaskets & Screw Caps.

SLIDING FRAMELESS GLASS DOOR: Providing & Fixing of Modular Aluminium single leaf Stile door frame of make 45 mm System

duly Anodized Aluminium Sections using KL 45 001 & KL 45 003 (45mm x 45mm) and Stile door of size 60x35mm as door frame with

3.03 MR Toughened Glass of Thickness 10 mm. Hardware as per make list and Lever Handle with Mortise Lock, Exposed Door Closer, Set of 4

Hinges, Door Stopper and required accessories ,Silicone/Thermoplastic Gaskets & Screw Caps.

i) Sliding Door Size: 1200x2400mm NOS. 1.00 52,000.00 52,000.00

WOODEN DOOR FRAMES : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed

9.1 and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood CUM 1.00 142,949.70 142,949.70

FLUSH DOOR SHUTTERS : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

9.21 core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or

cross bands and face veneers on both faces of shutters:

9.21.1 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 22.00 2,392.65 52,638.30

WOODEN LIPPING : Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

shutters (over all area of door shutter to be measured).

Providing and Fixing 22x922 mm D-type Handle Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of approved make and

model all complete as per the direction of Engineer-in-charge.

Providing and Fixing SS Mortise Lock Body SB/TB for door thickness 25-50 mm for of approved make and model all complete as per

the direction of Engineer-in-charge.

Providing and Fixing Double cylinder Floor Spring- with Closing Force EN 3 with Maximum door weight 105 Kg. Maximum door width

950mm.Closing speed : 130°

3.09 MR Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested with 5 Each 20.00 7,850.00 157,000.00

Years Warranty against manufacturing defect. CE certified for wooden doors all complete as per the direction of Engineer-in-charge.

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and

3.10 9.53 embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm EACH 72.00 228.85 16,477.20

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-

blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having

3.11 MR minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch SQM 51.00 1,200.00 61,200.00

(0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors). Contractors

payment wouldn't be released until & unless he/she produces orginal warranty certificate from the manufacturer.

Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

DSR ITEM NON DSR ITEM

ACOUSTIC PANELLING: PET Panels made of Polyester in size 2440x1220 mm with thicknesses of 9mm. Density is 1650 gsm for

9mm. The panel can plain/printed/ embossed/ customized to form different patterns. Panels can be cut to customize shape and size to

make different patterns. The acoustic panels should have an NRC of up to 0.3-0.6 Bollard PET Panels should be made of recycled

3.12 MR material and should be 100% recyclable. The panels need to be installed as per approved pattern and color on a plain wall. The panel SQM 35.00 2,620.00 91,700.00

needs to be glued or nailed with headless nails. Thickness: 9 Sheet Size: 2440mm x 1220mm Tolerance: +/- 5% Density: 1650 gsm

Fire Resistance: EN13501 – Class B s1, d0(SGS) NRC: 0.3 – 0.6mm, depending on the air gap between the wall and the panel

Shades: 36 shades available Material: 100% Polyester

LACQUERED GLASS: Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of approved color by Client /

Engineer in charge, fixed with compatible neutral grade silicon on a perfectly levelled 12mm thick water proof marine plywood / MDF /

Mineral fibre board which is mounted on RCC wall/any other structure. Lacquered glass must be made industrially (using curtain

3.13 MR coating process); opaque (if viewed against a support wall), uniformly coated with PU lacquer (50 micron thick coating or more); panel SQM 35.00 3,900.00 136,500.00

to panel colour consistency (measured by photo spectrometer); highly durable (passes hardness test for minimum 220 oscillations);

humidity resistance (conforms to BS EN 1036 1999 or equivalent) ; environmentally friendly having Low VOC (no lead, no arsenic,

no copper, no formaldehyde), low VOC content <100g/l. Silicone used should not react with lacquer coating (compatible neutral cure

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both

side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

9.105 and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon

3.14 plugs at spacing of 450mm centre to centre, and fixing of boards to both side of frame work by 25mm long dry wall screws on studs,

floor and ceiling channels at the spacing of 300mm centre to centre. The boards are to be fixed to the frame work with joints staggered

to avoid through cracks, M.S. fixing channel of 99mm width (0.9mm thick having two flanges of 9.5mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish

with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of

primer suitable for board as per manufacturer's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to

IS: 2095: part 3 (Board with BIS certification marks)

ACRYLIC SOLID SURFACE CLADDING : Providing & fixing of straight Paneling for walls & Columns structures anchored in floor slab

& celling, cladded with Acrylic Solid Surface 6mm thick sheets straight fabricated on a single face, finished in matte finish, pasted with

industrial grade silicon on a robust substrate. Substrate shall be with suitable MS box sections [Appx. 15 to 20 kg/ Sqm] as per

3.15 MR structural requirement & duly painted with anti-rust red oxide coating and covered with 12 mm thick water proof ply as per the design SQM 20.00 9,210.00 184,200.00

and dimensions approved. The proposal includes the cost of preparing appropriate substrate surface over the civil structure provided,

along with material cost & installation / fixing on straight walls etc. FOR ALL WALL CLADDING, TABLE TOPS ETC. COMPLETE

ROLLER BLINDS : Providing & supplying of Window Blinds as per the approved sample in required shade and style consisting, of

Roller Blinds comprising of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m,

Thickness 0.67 mm, Yarn count 18-19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-5659-2 .The tear

resistance should be complying to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick,easy and

safe installation,moulded plastic with steel spring support and inserted into the tube end. It shall be driven by a ball chain pulley with ball

chain and can be positioned at right side or left hand side of the Shade. The Shade when lowering or raising, shall be automatically

locked in position upon release of the ball chain by means of a built in friction lock.Universal clutch for left and right hand

operation.Chain Gear Ratio of 1.75:1.The END PLUG shall be molded of plastic witha steel location pin. The plug shall be inserted into

3.16 MR the tube end. (Opposite to the Drive Unit) for ease of installation. TheSUPPORT BRACKETS shall be of coated steel & provided with SQM 200.00 1,871.00 374,200.00

covers and used in right hand or left hand positions differentiated by the acceptance of the of the rectangular drive unit support or the

round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket should be protruding

outside maximum of80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter & skin thickness of 1mm

and shall incorporate a key way integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom made up

of powder coated steel. The BALLCHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on

6mm pitch to form an endless ballchain.It is used for raising or lowering action of the shades.hall be suitable for sill, face or side facing.

Cord Equalizer shall be injection melded from impact modified acrylic with a high flexural modulus

Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

DSR ITEM NON DSR ITEM

PELMET: Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed three layer or graded plain wood particle board

medium density grade I, ISi marked and conforming to IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming

3.17 9.42 to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 RM 56.00 600.55 33,630.80

mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and

rawl plugs 75 mm long etc. all complete.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up

3.18 to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 5.00 1,123.80 5,619.00

3.19 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. Sqm 5.00 104.80 524.00

13.4 12 mm cement plaster of mix :

3.21 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth Sqm 575.00 262.70 151,052.50

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,

Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives

New work (Two or more coats applied @ 1.43 litre/10 sqm) over and including priming coat of exterior primer applied @ 0.90 litre/10

PLY: Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved primer on one face, and

3.23 fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type SQM 657.00 1,224.65 804,595.05

4MM THICK MDF BOARD: Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved

3.24 MR primer on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge

4mm thick MDF Board SQM 510.00 270.00 137,700.00

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section placed at 600mm centre to centre

3.25 MR both ways (horizontal & vertical) fastened to floor, ceiling and horizontal member. The item includes providing and fixing 50mm thick SQM 329.00 1,347.00 443,163.00

polyester synthetic insulation as insulation of 100 GSM.

LAMINATE: Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high

3.26 9.127.2 density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of SQM 553.00 897.30 496,206.90

adhesive of approved quality. 1MM THICK

3.28 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to

9.24.1 Rectangular or square SQM 22.00 199.15 4,381.30

3.29 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc.

21.3 complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in

21.3.3 With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) SQM 3.00 1,685.40 5,056.20

3.3 Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm

12.57 thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI SQM 329.00 358.50 117,946.50

wire etc. complete as per directions of Engineer-in-Charge.

3.31 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield

10.27 strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-charge.

Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

DSR ITEM NON DSR ITEM

TOTAL WALL FINISHING WORKS 2,455,192.05 2,212,727.00

4 MISCELLANEOUS WORKS

MODULAR KITCHEN - UNDER COUNTER STORAGE CABINETS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient

number of drawers made of 18 mm thk. ISI Marked comm. ply, all ply to be laminated with 0.8 mm laminate.All shelves should be

supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia

shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high

gloss acrylic of approved. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs which will be

covered with PVC skirting in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/ slab

using metal screws of appropriate size and rawl plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be

considered for measurement and payment. Cabinet boxes size would be varies from 400x560x710MM to 1000x560x710MM (approx.)

and join together as per site requirements etc.

MODULAR KITCHEN - OVERHEAD STORAGE WALL UNITS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient

number of drawers made of 18 mm thk. ISI Marked comm. ply. All ply to be laminated with 0.8 mm laminate.All shelves should be

supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia

4.02 MR shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high SQM 3.00 5,125.00 15,375.00

gloss acrylic of approved. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front

face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size

would be varies from 400x560x710MM to 1000x560x710MM (approx.) and join together as per site requirements etc.

4.02A MR Providing and fixing of Innotech with metal sides and quadro channels Each 5 3,548.00 17,740.00

4.02B MR Providing and fixing baskets Each 5 4,013.00 20,065.00

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C.,

kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of

4.03 22.3 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including SQM 6.00 769.60 4,617.60

rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per

sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to

each other with bitumen @ 1.7 kg/sqm).

DISMANTLING: Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of

unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-Charge.

TOTAL MISCELLANEOUS WORKS 4,617.60 172,398.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR/ MR TOTAL AMOUNT TOTAL AMOUNT

DSR/ MR TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT QUANTITY RATE

2023 DSR (INR) NON-DSR (INR)

1 Supply Installation, Testing and Commisioing of Handicap Toilet special fixtures

to the complete satisfaction of the engineer in charge

MR (a) SITC of Grab Bar vertical swing white(Ref. Jaquar Cat. No. WAC-WHT-BG0800 Each 1 9867.00 9867.00

OR approved equivalent)

MR (b) SITC of Grab Bar Left/Right 90 angle, White (Ref Jaquar WAC-WHT-BAD090 Each 1 7271.00 7271.00

MR (c ) SITC of Grab Bar 842mm long white, White (Ref Jaquar WAC-WHT-BRO750) Each 1 4664.00 4664.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

1.10 conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

1.55 surface / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.3 1.12 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS Metre 2415 334.00 806610.00

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

1.24 box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 263 122.00 32086.00

1.24.5 6 pin 15/16 amp socket outlet Each 32 197.00 6304.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

A.6 1.26 excluding modular plate as required. Each 20 40.00 800.00

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

1.5 sq. mm + 1 X 1.5 sq. mm earth wire

1 Digitally signed by AMIT

B.1 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 20 439.00 8780.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 45 1005.00 45225.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 45 1365.00 61425.00

Supplying and making end termination with brass compression gland and aluminium lugs for

9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

Conductor Cables :

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively &

(b) 3.5 C x 95 Sqmm XLPE cable RM 5 864.00 4320.00

(c ) 3.5 C x 70 Sqmm XLPE cable RM 20 102.69 2053.88

(d) 3.5 C x 50 Sqmm XLPE cable RM 10 510.00 5100.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 10 378.00 3780.00

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

D.2 connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

D.4 required. (But without MCB/ RCCB/ Isolator)

2 Digitally signed by AMIT

MR 12 way (4 + 36), Double door Each 5 9081.00 45405.00

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

the existing MCB DB complete with connections, testing and commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supplying and fixing following modular switch / socket on the existing modular plate & switch

1.24 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 9 148.00 1332.00

1.24.6 Telephone socket outlet Set 51 148.00 7548.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 5 1639.26 8196.30

E.9 (b) 225mmx38mm(GI) - 3 compartment Mtr 10 1339.36 13393.59

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables

at the intersection of raceways supplied completely with base and cover plates, height

MR adjustable junction box 65- 90 mm including all accessories ss plate of 3mm thick complete

in all respect as per the directions of engineer in charge

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.11 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Meter 270 47.00 12690.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

1.21 surface/ recess including cutting the wall and making good the same incase of recessed

E.12 conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S.

cable trays of perforation of not more than 17.5% in convinient sections, joined with

4.1 connectors suspended from the cieling with MS suspenders including bolts and nuts painting

suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 20 1137.00 22740.00

E.14 1.18 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper

conductor, unarmoured telephone cable in the existing surface/ recessed steel/ PVC conduit

3 Digitally signed by AMIT

Earthing with GI earth plate 600 mm X 600 mm X 6 mm thick including accessories, and

F.1 5.4 providing masonry enclosure with cover plate having locking arrangement and watering pipe SET 4 7472.00 29888.00

of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 200 70.00 14000.00

G PANEL BOARDS

Fabricating, Installing, Testing & Commissioning of automatic mains failure control

including auto by-pass panel, suitable for 125 KVA silent type DG set complete with

relays, timers, set of CTs for metering & protection and energy analyser to indicate

currents, phase and line voltages, frequency, power factor, KWH, KVARH & provision

for overload, short circuit, restricted earth fault, under frequency, control cabling from

AMF panel to diesel engine and elsewhere if required, all complete and inter locking

including the following:sheet steel cubicle type panels fabricated from 14 guage

thick CRCA sheet, dust and vermin proof, indoor type MV Panels with hinged lockable

Colour: Gray Powder Coated, as per approved sample.

Note: All MCCBs of 250 amps and below rating shall be provided with thermal

100 Amps. & pole

Four MCCBs above

Moulded 250 Circuit

Case amps Breaker

rating shall be breaking

of fault providedcapacity

100 Amps. up pole

Four to 433 V) completewith

Moulded extended

Case Circuit BreakerRotary Mechanism

breaking capacity 36

KA (ICS=100% ICU up to 433 V) completewith extended Rotary

1 Nos. 300 Amp. 415 volt AC 3 duty 4 pole contactor - 2nos Mechanism and

1 No. 300 A 415V, AC , 4P Manual Changeover with Operating Handle

Auto/Manual/Test/Off selector switch

2 Nos. over voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay.

3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for

Energy analyser unit to indicate current voltage frequency power factor and KWH

Indicating lamps for load on mains and load on set

Fuse for instruments

G.1 MR Battery charger, complete with transformer/rectifier, D.C. voltmeter and ammeter,

supply for trickle,

failure monitor off and boost and current adjustment.

Supply Failure Timer

Restoration Timer

Control unit with three impulse automatic engine start/stop and failure to start lockout

Impulse counter with locking and reset facility.

ON/OFF/Control circuit switch with indicator

Audio/Video annunciation for.

4 Digitally signed by AMIT

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

TPN aluminum bus bars of minimum of 200 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -4 Nos.

(b) 40 Amps, TPN, MCB - 6 nos

Panel complete as above Each 1 195000.00 195000.00

30 OUTDOOR PANEL FOR VRV

MR Fabricating, Installing, Testing & Commissioning of automatic mains failure control

including auto by-pass panel, suitable for 125 KVA silent type DG set complete with

relays, timers, set of CTs for metering & protection and energy analyser to indicate

currents, phase and line voltages, frequency, power factor, KWH, KVARH & provision

for overload, short circuit, restricted earth fault, under frequency, control cabling from

AMF panel to diesel engine and elsewhere if required, all complete and inter locking

including the following:sheet steel cubicle type panels fabricated from 14 guage

thick CRCA sheet, dust and vermin proof, indoor type MV Panels with hinged lockable

doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz

AC supply with rear / bottom access for cable alley and with segregated bus-bar

chamber and including supplying and fixing following switchgears, meters and

accessories, inter-connections, bonding to earth, bottom base channel of MS section

not less than 100mmx50mmx5mm (thick). Fabrication shall be done in transportable

section ,entire panel shall have a common earth busbar at rear with 2 nos earth stud

cable alleys, cable gland plates powder coated painting of approved shade after

antirust treatment (with min seven tanks ) and marking as specified. Switch boards

complete as per schematic diagram:

Colour: Gray Powder Coated, as per approved sample.

Note: All MCCBs of 250 amps and below rating shall be provided with thermal

magnetic release & MCCBs above 250 amps rating shall be provided with

Microprocessor based release. (All MCCBs shall be fitted with extended type rotary

handles and spreader links)

1nos, 160 Amps. Four pole Moulded Case Circuit Breaker of fault breaking capacity 36

KA (ICS=100% ICU up to 433 V) completewith extended Rotary Mechanism and

Spreader Link Set with microprocessor release for O/L, S/C & E/F protection.- Mains

5 Digitally signed by AMIT

1nos, 160 Amps. Four pole Moulded Case Circuit Breaker of fault breaking capacity 36

KA (ICS=100% ICU up to 433 V) completewith extended Rotary Mechanism and

Spreader Link Set with microprocessor release for O/L, S/C & E/F protection.- DG

1 Nos. 300 Amp. 415 volt AC 3 duty 4 pole contactor - 2nos

1 No. 300 A 415V, AC , 4P Manual Changeover with Operating Handle

Auto/Manual/Test/Off selector switch

2 Nos. over voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay.

3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for

Energy analyser unit to indicate current voltage frequency power factor and KWH

Indicating lamps for load on mains and load on set

Fuse for instruments

Battery charger, complete with transformer/rectifier, D.C. voltmeter and ammeter,

selector switch for trickle, off and boost and current adjustment.

Main supply failure monitor

Supply Failure Timer

Restoration Timer

Control unit with three impulse automatic engine start/stop and failure to start lockout

Impulse counter with locking and reset facility.

ON/OFF/Control circuit switch with indicator

Audio/Video annunciation for.

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

250 Amps TPN aluminium bus bars with heat shrinkable coloured sleeves and i/c DMC/SMC

bus bars supports at required intervals complete for cross section, size supports & their

(a ) 63 Amps, TPN MCB +ELCB- 3 nos

(b ) 40 Amps, TPN MCB + ELCB - 3 nos Each 1 225000.00 225000

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2

16 2.21 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour on Nos. 4 269.00 1076.00

front side as required

6 Digitally signed by AMIT

MR Supply, Installation, Testing and Commissiong of 10 KVA True Online UPS 3 Phase Input -

3Phase Output in Parallel Redundant N+1 Configuration IGBT Based Rectifier and IGBT

Based Inverter Batteries:12 V, SMF Amararaja/Exide with minimum VAH capacity of 15600

suitable for 15 minutes backup with each ups Along with Accessories Rack, Interlinks, SFU,

18 Parallel Kit, DC Cable Upto 5 Meters complete in all respect as per the directions of the Nos. 2 407100.00 814200.00

engineer in charge. UPS should have availability of Input /Output isolator, Inbuilt manual

bypass along with phase sequence corrector. UPS Efficiency shall not be less than 94% from

25% to 100% Load

Total of Electrical items 1830192.00 1563745.76

7 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR HVAC TOTAL TOTAL

S No 2019/DSR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

EM 2018 DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,

having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors

for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as

1 1.0 required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C per HP 70 16415.00 1149050.00

ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3

Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER

not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity 4-way flow

VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable

media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed

motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain

2 2.0 pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for

single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have

automatic force shut down provision in case of fire on receiving signal from BMS System.

The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature.

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High

wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low

noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil,

electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary

3 3.0 accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply,

complete as required. The unit shall have automatic force shut down provision in case of fire

on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

Digitally signed by AMIT

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T"

4 4 Joints i.e. Refnet Joints/ Header with Insulation for refrigearnt piping

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen

testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF

system, complete with fittings, with suitable adjustable ring type hanger supports,

jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with

Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness

as given below for Suction and Liquid lines, all accessories as per specifications etc. as

5.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 150 245.00 36750.00

5.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 240 331.00 79440.00

5.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 150 466.00 69900.00

5.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 240 588.00 141120.00

5.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 30 707.00 21210.00

5.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 30 865.00 25950.00

5.7 5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 20 1022.00 20440.00

5.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 20 1108.00 22160.00

5.9 5.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 20 1170 23400

6 5.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 20 1230 24600

6.1 5.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 10 1265 12650

6.2 5.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 10 1309 13090

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC

conduit as required.

Supply,installation,testing and commissioning of PVC drain water with necessary clamps,

fittings such as bends tees etc. and duly insulated.

Digitally signed by AMIT

Supply, Laying, Termination of ISI Certified 4 Core 1.0 sq.mm ATSC, FRLS ,PVC insulated,

Unarmored, Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable

10 MR with proper ferrules, lugs and other necessary accessories. The spec shall meet the system Rmt 390 280.00 109200.00

manufacturer specifications.

Total HVAC WORKS 2538278.00 530016.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO DSR/MR Description Unit QTY Rate DSR AMOUNT NON DSR AMOUNT

Supply, Installation, Testing and Commissioing of LED Pendant luminaire with

LED(Light Emitting Diode) system power: 28W, 120 LM/W system efficacy,

colour temperature of 4000K, neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, CRI>80,

luminous flux of 3360 lm, MacAdam 3, T.H.D≤10%, driver efficiency ≥ 88%,

1 MR surge protection of 2.5kV, direct light emission, Aluminium body, polyester no 23 5195.00 119485.00

white powder coat applied over a 5-stage pre-treatment, Prismatic diffuser for

glare-free uniform light, UGR<19, Electronic control gear

Protection class I, IP40, L =1195mm, B = 295mm, H = 67mm, PH = 1500mm

Supply, Installation, Testing and Commissioing of Recessed downlightwith

HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system

power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy,

Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours; energy-efficient

2 MR LEDs, direct light emission, housing in die-cast aluminium, Polyester powder no 59 1394.00 82246.00

white coloured coat applied over a 5-stage pre-treatment trim, prismatic

diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear,

Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm

Supply, Installation, Testing and Commissioing of Pendant/Recessed

luminaire with LED (Light Emitting Diode), system power 28 W, luminous flux

of luminaire 3080 lm, 110 LM/W system efficacy, direct light emission CRI>80,

colour temperature of 4000K, Neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, luminaire

profile in aluminium, Plastic moulded end caps, Polyester powder Aluminium

3 MR white coloured coat applied over a 5- stage pre-treatment, high efficiency glare- no 65 4001.00 260065.00

free snap fit micro-prismatic diffuser for homogeneous light distribution, ZHLS

(Zero Halogen Low Smoke) internal wiring, integral Electronic control gear,

adjustable suspender, including cost of all connectors to create continuous

cascading effect.

Protection class I, IP 20, L = 1199 mm, B = 75 mm, H = 90 mm, PL max =

1 Digitally signed by AMIT

Supply, Installation, Testing and Commissioing of Pendant/Recessed

luminaire with LED (Light Emitting Diode), system power 14 W, luminous flux

of luminaire 1500 lm, 110 LM/W system efficacy, direct light emission CRI>80,

colour temperature of 4000K, Neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, luminaire

profile in aluminium, Plastic moulded end caps, Polyester powder Aluminium

4 MR white coloured coat applied over a 5- stage pre-treatment, high efficiency glare- no 5 2800.00 14000.00

free snap fit micro-prismatic diffuser for homogeneous light distribution, ZHLS

(Zero Halogen Low Smoke) internal wiring, integral Electronic control gear,

adjustable suspender, including cost of all connectors to create continuous

cascading effect.

Protection class I, IP 20, L = 599 mm, B = 75 mm, H = 90 mm,

Supply, Installation, Testing and Commisioning of Recessed downlight with

LED (Light Emitting Diode) system power: 5W, Luminous flux of luminaire 400

lm, Colour temperature of 4000 K, Warm white, CRI > 80, 230V constant

current driver, 70% of luminous flux after 50,000 operating hours; energy-

efficient LED, direct light emission, housing in die-cast aluminium, Polyester

powder white coloured coat applied over a 5-stage pre-treatment ceiling trim,

5 MR with reflector, beam angle of 24°, Electronic control gear, no 4 1200.00 4800.00

Protection class II, IP 20,

Supply, Installation, Testing and Commisioning of Recessed with trim

luminaire with Pinspot light with LED(Light Emitting Diode) system power: 8W,

luminous flux of luminaire 640lm, colour temperature of 4000K,

CRI > 90, SDCM<3, THD<10%, 230V constant current driver,

70% of luminous flux after 50,000 operating hours, direct light

emission, aluminium housing with trim, polyester Black powder

coat applied over a 5 stage pre-treatment on trim, with lens and

a beam angle of 36° and external Electronic control gear

2 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - FIRE ALARM

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

Supplying, installation, testing & commissioning of intelligent analog addressable

1 17.2.4 photothermal detector complete with mounting base complete as required. No 43 2858.00 122894.00

Supplying, installation, testing & commissioning of response indicator on surface/recessed

MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector

with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as

Supplying, installation, testing & commisssioning of intelligent addressable programmable

5 17.2.6 sounder complete as required. No 1 2651.00 2651.00

Supplying, installation, testing & commissioning of addressable manual call point complete as

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed

7 17.5.2 copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath Mtr. 450 173.00 77850.00

complete as required

Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power Battery

backup complete as required.

TOTAL FIRE ALARM WORKS 244206.00 15480.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

18.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the

wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint

of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

18.21 quartzoid bulb type sprinklers of rating 68 degree

2 centigrade with required accessories :

18.21.1 Pendant type 80 Each 522.00 41760.00

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with maximum

working pressure of 175 PSI test pressure of 875 PSI

3 18.25 (Burst) with branch line (Inlet) 25mm NPT male thread to

sprinkler head (Outlet) 15mm NPT female thread with

reducer, nipple, 2 side brackets, center bracket, stockbar

of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire

4 Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 2 NOS 12912.00 25824.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: IT

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S No Description UNIT QUANTITY RATE

A. UTP Components for Data DSR (INR) NON-DSR (INR)

Supply, Fixing & Laying of CAT 6A UTP cable 23 AWG solid copper

1 conductors for Connectivity of Hub room to End Point.High Speed Gigabit Mtr 3125 58.00 181,250.00

Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6A cable

termination at Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply , Installtion , Testing and Comissioning of CAT6A patch cord 2 Mtr (7

3 feet) for information outlet (I/O) to end user device connectivity.High Speed Nos. 125 350.00 43,750.00

Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of CAT6A patch cord 1 Mtr (3

4 feet) for information outlet (I/O) to Rack End Redantant device Nos. 125 279.00 34,875.00

connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of 24 port Loaded Jack Panel

for CAT6A cable termination at rack end. Data Active

C. Backbone Component

SITC of Multimode Fiber Patch Cord

D. Network Rack and Other Accessories

7 SITC of 32U Rack Wall Mount Nos. 1 30,000.00 30,000.00

SITC of router with Aggregate Throughput (Default) 100mbps, Aggregate

Throughput (Performance License) 500Mbps, Total onboard WAN or LAN

10/100/1000 ports 2nos, RJ-45-based ports 4nos, SFP-based ports 2nos,

9 NIM slots 2nos, Default memory DDR3 ECC DRAM (data plane) 2gb, Nos. 1 150,000.00 150,000.00

Maximum memory DDR3 ECC DRAM (control/servic es plane) 16gb, Default

flash memory 8gb, USB console port -type B mini (up to 115.2 kbps) 1nos

SITC of Access Switch with minimum of 24x 10/100/1000 Base-T ports, 4x

10 Gig SFP+ ports for uplink ports(supporting Single mode & Multi mode

10 1G/10G (LX, LR, SX & SR modules). Should have Non-blocking switch Nos. 3 250,000.00 750,000.00

fabric, IPv6 Ready with RPS 1 years warranty support for Access Switches.

SITC of Hardware controller managed Indoor Wi-Fi Access Point with

Adapter for power supply

12 SITC of 1 Gig SR transceivers/equivalent LC connector MM Nos. 6 15,374.00 92,244.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: CCTV

Total Estimate

Sr No Item Description UoM Estimate Amount

SITC of 2MP, 1/2.8” CMOS image sensor, low illuminance, high image definition, Outputs 2MP

(1920 × 1080) @ 25/30 fps Built-in IR LED, max IR distance: 30 m, Intelligent detection: Intrusion,

tripwire,Abnormality detection: Motion detection, video tampering, no SD card, Supports max. 256

GB Micro SD card, IP67, IK10 protection etc all complete.

SITC of 8 channel Smart H.265+/H.265/Smart H.264+/H.264/MJPEG decoding format. · Max.

decoding capability: 32 × 1080p@30 fps or 32 × 2MP@30 fps. · Max. 384 Mbps

incoming/recording/outgoing bandwidth. · Support AcuPick with Max. 16-Channel. · Support N+M

cluster. · AI by recorder: 2-channel face detection and recognition, 4-channel perimeter protection,

and 8-channel SMD Plus. · AI by camera: Face detection and recognition, perimeter protection,

SMD Plus, metadata, ANPR, stereo analysis, heat map, and people counting etc all complete.

3 SITC of Hard Disk 10TB required for the above NVR etc all complete. No's 1 31,855.00 31,855.00

4 CAT6 Patch Chord in existing Network Rack No's 4 5,800.00 23,200.00

5 CAT6 IO / Connector at camera location No's 4 5,000.00 20,000.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: IPBAX

Sr No Item Description UoM Rate DSR Amount Non DSR Amount

1 SITC of EPABX Intercom with 4 incoming lines and 64 Anolog Extensions complete in all respect No's 1 55,000.00 55,000.00

2 SITC of Analog Phones No's 51 1,500.00 76,500.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: Audio Visual

Unit rate Total

Sr No Item Description UoM

SITC of Cable Cubby with flip top, cover and 6 Pass Through Holes for multi-

1 format cables, 2 Universal Power Socket , 1 HDMI, 1 USB-C for Data Transfer, No's 2 17,850.00 35,700.00

made of aluminium etc all complete etc all complete

SITC of 20 Meter Conference system extend cable between terminals, 8-pin high-

density cable with one Side Male Connector & one Female Connector

SITC 2 Meter Conference system extend cable between terminals, 8-pin high-

3 density cable with both Side Male Connectors to Connect Controller with Extended No's 4 1,320.00 5,280.00

SITC of 2m/6.5ft HDMI 2.0 Cable, 18Gbps 4K60Hz, Dolby Vision & HDR,

ARC,CEC, ALLM, VRR, | CL3 & VW-1 Rated etc all complete

SITC of 5 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to

5 18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4 video resolution, High Dynamic No's 3 4,575.00 13,725.00

Range (HDR10), Dolby Vision and Hybrid log–gamma (HLG) video etc all complete

SITC of10m HDMI 2.0 AOC | 24Gbps | 4K60Hz | Dolby Vision & HDR | ARC, CEC,

ALLM & VRR | ISF Certified | FT4, CL4 etc all complete

SITC of Microphone Cable, 2 Conductor 22 AWG Tinned Copper, PE Insulation,

7 85% Tinned Copper Braid Shield, Cotton Braid, PVC Jacket (as per actual) etc all Meter 50 180.00 9,000.00

SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper conductors,

PVC/Nylon insulation, PVC jacket (as per actual) etc all complete

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

TABLE FOR ZONAL / REGIONAL MANAGER

TABLE- W 2300 x D 1000 x H 750mm SIDE TABLE- W 1400 x D 550 x H 750mm

Main Table: The table top dimensions will be 2300x 1000x750 mm made in PLB (Pre laminated Fibreboard) with the

density of 680kg/m³ and 25mm thick one side pre-laminate board confirming to IS-14587:1998. Surface: CPL

(continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as

per the JIS A 5905-2003 standards and approved shade confirming to IS-12823:1990. 2 mm thick PVC edge band will

confirm to DIN 68861 for resistance to clearers. The edge band material should have Shore D hardness of 79± 4. The

Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification confirming to

ASTM D 4499 standards for viscosity and thermal stability. The top surface will have 30 mm aluminium channel ( Z

Section) all round the main table at the edges below the top surface. There will be a support pedestal extended by

200 mm on the right side below the main table thus achieving over all dimension of 2300 x1000 mm.

The return table will be 1300x550 mm in PLB confirming to IS- 14587:1998. Surface: CPL( continuous pressure

laminate) in 0.5mm thickness. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and

approved shade confirming to IS-12823:1990. 2 mm thick PVC edge band confirming to DIN 68861 for resistance to

clearers. The edge band material should have Shore D hardness of 79± 4.. The hot melt glue used for fixing the PVC

edge band should have ISO 9001- 2015 quality certification confirming to ASTM D 4499 standards for viscosity and

thermal stability. The return table will be connected to the main table by structurally engineered MS connector of

thickness 2mm which has undergone zinc passivation confirming to IS:1573 – 1986. Two connectors will be used.

Support bracket: The main table and the return table will be supported by 130 mm high aluminium die cast

structural bracket designed in “V” shape to withstand at optimum load, made in LM6 (Al-Si12 - EN1706 AC-44100),

confirming to BS 1490:1988 LM6, The structural bracket will have suitable design to rest on the support pedestal

and the Gable End panel. The aluminium bracket will be powder coated as per the approved colour. The aluminium

1 bracket should undergo 7 step rust resistance pre treatment process viz degreasing, pickling as per IS standard. 1 NOS ₹ 154,611.00 ₹ 154,611.00

Modesty panel: The table will be provided with Modesty panel connecting the support pedestal and the gable end-

size 1420x 450 mm. The modesty will be made in PLT(laminated both sides) 18 mm thick confirming to E-1 Grade as

per the JIS A 5905-2003 standards and approved shade confirming to IS-12823:1990. The modesty have 2 mm thick

PVC edge band confirming to DIN 68861 for resistance to clearers. The edge band material should have Shore D

hardness of 79± 4.

Support pedestal: The support pedestal size 600(W) x 850(D)x 590(H)will be made in PLB confirming IS- 14587:1998.

The PLB will be 25 mm thick PLT. Pedestal construction will be in three equal drawer box construction made in 12

mm PLT in black finish . Drawer facia will be made of 25mm thick PLB one side pre-laminate board confirming to IS-

14587:1998. Drawer telescopic channel will have extension of 450 mm with silver anodised finish. The slides will be

cycle tested to BIFMA standards- minimum 50000 times .

Gable End: The under structure will have on one side gable end support 50 mm thick in PLT(Laminated both sides)

confirming to E-1 grade as per IS- 12823:1990. The 50 mm thick Gable end shall comprise of 25 mm PLT + 25 mm

PLB as per IS: 12823. The edges will have 2 mm PVC edge band confirming to DIN 68861 for resistance to clearers.

The edge band material should have Shore D hardness of 79± 4.. The hot melt glue used for fixing the PVC edge

band should have ISO 9001- 2015 quality certification confirming to ASTM D 4499 standards for viscosity and

thermal stability. The gable end will support the main table with the aluminium die cast bracket as per the design

required confirming to EN 573-3:2009 with alloy 6063 A grade. The aluminium bracket should be powder coated as

the required criteria.

Wire management: the main table will be provided with soft closing “Flip up” on the right side above the support

pedestal- The “Flip up” will be 300 mm having an aluminium cover with soft closing arrangement and three side

accesses for the cables. The “flip up” will be in anodised in silver finish. The “flip up” will be a PVC cable tray for

cable management and termination.

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

HIGH BACK CHAIR FOR REGIONAL MANAGER

SPECIFICATION:-

Seat is made out of 9 layer 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in

to the wood.Gaslift - Class 4

tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 –

2002.Specially designed metal base 5 pronged structure forged out of CR Sheets of 2 mm thick. Base of diameter 26 inches

for complete stability, extreme durability, sturdiness and pleasant

aesthetic looks. Reinforced with CO2 welding to provide additional strength and support. Tested prudently and rigorously as

per ANSI/BIFMA X5.1-2011

General Purpose Office Chair Standards.Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of

plywood with leatherette tapestery. Density -- 52 kg/m3 / Hardness -- 12.6kgf at 25%.Distinctively and characteristically

2 designed tilt mechanism offering a very smooth and fluidic reclining motion 1 NOS ₹ 24,022.80 ₹ 24,022.80

with tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back support.Multilock

fabricated from CR Sheets, undergo through CO2 welding process imparting uniform surface finish and tensile strength. The

processed with high degree of precision and care so as to assemble with other parts in perfect harmony to give smooth and

effortless reclining

experience. Tension springs are made out Grade II material conforming to Indian Standards. Also provided with release

levers for locking

mechanism and height adjustment of seat. Mechanism aides to operate the height adjustment, and has been equipped with

4 locking positions,

back rest “ Return Prevention” function .Cusioned Back with Leatherette tapestery used for back upholstery With Unique

VISITOR CHAIR FOR REGIONAL MANAGER

SPECIFICATION:-

Supply and Placing in position of Visitor Chairs of approved make. The seat is cushioned seat made of injection molded

plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density

45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The

back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm,

upholstered with leatherette. The back size is 47.7 W cm x 60.1 D cm. The tubular frame is cantilever type and made of

3 Ø2.54±0.03cm x 0.2±0.016 cm thick SS 202 tube. The back connected to frame through chrome plated high pressure die 3 NOS ₹ 14,910.30 ₹ 44,730.90

casted connector pipe. All the dimensions will be as per the Original Manufacturer's Specifications. The product should be of

BIFMA compliance, ISO 9001:2015 and ISO 14001:2015 complete as per approved sample and as per the direction of

EngineerIn-charge.

SOFA 3-SEATER FOR REGIONAL MANAGER

SPECIFICATION:-

Seat Foam: the sofa is made up of fine quality leatherette.The structure is made up of silver wood and pine wood.The Seat is

made of PU Foam with Density 32 to 40 +/- 2 kg/cu .mtr Seat is upholstered wuth Leatherite.Back Foam: The Back is made

of PU Foam with Density 32 to 40 +/- 2 kg/cu, Backis upholstered with Leatherite.Unterstructure is made up of silver wood or

pine wood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Legs

4 should be made up of solid wood having pu matt finish. 1 NOS ₹ 53,015.40 ₹ 53,015.40

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

CORNER TABLE FOR REGIONAL MANAGER

SPECIFICATION:-

The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in square shape with bevelled

edges. The top shall be supported on vacuum caps situated over SS 202 grade pipe frame. The under structure shall have

5 SS with shiny chrome finish pipe frame having dia. 20-25.4mm with 2mm thick. There shall be good quality PPCP shoe 2 NOS ₹ 9,808.20 ₹ 19,616.40

provided to avoid scratches on the floor.Top glass is partial tempered glass.

ADMIN ROOM TABLE

TABLE SIZE:-1650W X 750D X 750HT

EXTENTION:-900W X 450D X 750HT

BACK STORAGE:-3200W X 450D X 750HT

SPECIFICATION:-

MAIN TABLE:- The main table shall be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998.

Soft closing access flap with in-built power box to be provided on work surface for wire management. Return table Work

Surface should be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998. PLB will be E1-P2

grade and approved shade. Confirming to IS-12823:1990. 2 mm thick PVC edge band will confirm to DIN 68861 for

resistance to clearers. The edge band material should have Shore D hardness of 79± 4. The Hot melt glue used for fixing the

PVC edge band should have ISO 9001- 2015 quality certification confirming to ASTM D 4499 standards for viscosity and

6 thermal stability. The edges should be PVC Edge banded with matching finish or have an option of reverse water fall 2 NOS ₹ 67,630.50 ₹ 135,261.00

edges.Modesty Panel shall be made of 18mm thick PLT both sides pre-laminate board confirming to IS-14587:1998.The

height of modesty shall be 450 mm.The modesty panel will be connected to the main table by 2 nos special Aluminum

extruded brackets. The modesty will be fixed 150 mm from the edge of the table.Wire Management:Continuous PVC Cable

Tray with provision to mount switches and sockets as per client requirement. Vertical wire entry cover for wire uptake from

floor to cable tray and 300mm Aluminium Flip Up for swicth access.Legs and Supports:- The MS supports are made of 50

x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW

tube confirming to IS 4923: 1997. The vertical and the horizontal tubes will be welded with CO2 MIG welding process

confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic welding

machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care

TABLE stress catering

FOR ASSISTANT MANAGERup to 1800 mm length and up to 900 mm depth of the work surface.Finish:- All metal

TABLE SIZE: 1350W X 600D X 750HT

Specifications:

MAIN TABLE:- The main table shall be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998. Soft closing

access flap with in-built power box to be provided on work surface for wire management. Return table Work Surface should be made of 25mm

thick PLB one side pre-laminate board confirming to IS-14587:1998. PLB will be E1-P2 grade and approved shade. Confirming to IS-

12823:1990. 2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The edge band material should have Shore D

hardness of 79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification confirming to ASTM D

4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded with matching finish or have an option of reverse

water fall edges.Modesty Panel shall be made of 18mm thick PLT both sides pre-laminate board confirming to IS-14587:1998.The height of

modesty shall be 450 mm.The modesty panel will be connected to the main table by 2 nos special Aluminum extruded brackets. The modesty

will be fixed 150 mm from the edge of the table.

Wire Management:Continuous PVC Cable Tray with provision to mount switches and sockets as per client requirement. Vertical wire entry

7 cover for wire uptake from floor to cable tray and 300mm Aluminium Flip Up for swicth access. 6 NOS ₹ 25,370.00 ₹ 152,220.00

Legs and Supports:- The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm.

ERW Tube confirming to IS 4923 : 1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 50x25 cold

formed ERW tube confirming to IS 4923: 1997. The vertical and the horizontal tubes will be welded with CO2 MIG welding process confirming to

IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic welding machine to ensure adequate welding

strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering up to 1800 mm length and

up to 900 mm depth of the work surface.

Finish:- All metal components & aluminum die cast parts will be powder coated by Nano ceramic surface treatment process compiled to a Bend

test-ASTM D3451 – 06, Adhesion -DIN EN 14901 Salt spray test- DIN EN ISO 9227, which is non-hazardous, environmental friendly and will

have uniform powder coating thickness of 50-60-micron thickness.

MOBILE PEDESTAL:-400W X 450D X 600HT

The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and

drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operatedDigitally signed by AMIT

with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to Page

3 of 10 operation. The drawer SINGH

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

HIGH BACK CHAIR FOR DEPUTY MANAGER AND AUDIT ROOM

SPECIFICATION:-

Chair's Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and

revited in to the wood.Gaslift - Class 4 tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm dia

castors compling to ANSI / BIFMA X 5.1 – 2002.The 640mm dia (26 inches) five pronged base is made out of GF nylon –

Reinforced with bottom ribbing for additional buttress and strength.Tested prudently and rigorously as per ANSI/BIFMA X5.1-

2011 General Purpose Office Chair Standards.Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density --

8 52 kg/m3 Hardness -- 12.6kgf at 25%.This mechanism is manufactured out of cold Rolled Carbon Steel IS 513-1994 7 NOS ₹ 10,800.90 ₹ 75,606.30

Sheets,The steel components are manufactured with highly precision tools For accuracy in matching other parts for smooth

functioning. The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher

tensile strength. Springs are made out of Grade II material. Composite release levers for locking mechanism & Gas lift height

adjustment. Release lever mechanism for Locking and Gas lift height adjustment. Back Frame is upholstered with Thinner

Mesh Adjustable Lumbar Support Allows you to adjust the lumbar support position for good back support and blood

circulation.Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable -

Height Adjustable. Tension control is below the Seat.Seat are duly upholstered with approved fabric.

VISITOR CHAIR FOR DEPUTY MANAGER AND AUDIT ROOM

SPECIFICATION:-

Supply and Placing in position of Visitor Mesh back Chairs of approved make. The seat shall be made of 1.4 +/-0.1 cm thick

hot pressed plywood upholsterd with fabric and moulded polyurethane foam. It shall have fixed seat Seat size shall be 50.0

cm W x 49.0 cm D. The back shall be injection moulded in glass filled polyamide which shall be upholstered with mesh

fabric. The back shall consist adjustable lumbar support made of injection moulded polypropylene having an adjustment of

9 6.0 +/- 0.1 cm. Back size shall be 50.0 cm W x 68 .0 cm H. The polyurethane foam for seat shall have a density of 55 +/- 5 14 NOS ₹ 10,449.90 ₹ 146,298.60

kg/m³. The height adjustable armrest shall be made of polyamide structure and polypropylene housing with moulded PU arm

top having an adjustment of 7.0 +/- 0.3 cm. The sled base frame shall be Chrome plated welded tubular frame made of dia

2.8 +/- 0.03 cm X 0.2 +/- 0.02 cm thick MS round tube. The frame shall be fitted with plastic capsmade of injection moulded

glass filled polypropylene. Overall size of the chair shall be 62.0 cm W x 58.0 cm D x 97.0 cm H x 42.0 cm Seat Height. All

the dimensions will be as per the Original Manufacturer's Specifications. The product should be certified with BIFMA,

Greenguard, ISO 9001:2015 and ISO 14001:2015 complete as per approved sample and as per the direction of Engineer-In-

SOFA 2-SEATER FOR AUDIT ROOM

SPECIFICATION:-

Seat Foam: the sofa is made up of fine quality leatherette.The structure is made up of silver wood and pine wood.The Seat is

made of PU Foam with Density 32 to 40 +/- 2 kg/cu .mtr Seat is upholstered wuth Leatherite.Back Foam: The Back is made

10 of PU Foam with Density 32 to 40 +/- 2 kg/cu, Backis upholstered with Leatherite.Unterstructure is made up of silver wood or 1 NOS ₹ 35,343.00 ₹ 35,343.00

pine wood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Legs

should be made up of solid wood having pu matt finish.

SPECIFICATION:-

The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in square shape with bevelled

edges. The top shall be supported on vacuum caps situated over SS 202 grade pipe frame. The under structure shall have

SS with shiny chrome finish pipe frame having dia. 20-25.4mm with 2mm thick. There shall be good quality PPCP shoe

provided to avoid scratches on the floor.Top glass is partial tempered glass.

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

CONFERENCE TABLE

OVERALL SIZE - 4800W X 1800D X 750HT

MAIN TABLE SIZE - 1800W X 750D X 750HT(QTY-01)

SIDE TABLE SIZE - 1350W X 600D X 750HT(QTY-06)

Specifications:

Conference table in completely knock down conditions that is to be assembled at site. The construction of the main table shall be with minifix

dowels, pins and MS brackets. table tops will be made out of PLB will be E1- P2 25mm Pre-laminated particleboard (PLB) confirming to IS-

12823:2018 with 2 mm PVC edge banding. The table top will be made in PLB( Pre laminated board) with the density of 680kg/m³ and 25mm

thick one side pre-laminate board confirming to IS-12823: 2018. Surface: CPL( continuous pressure laminate) in 0.5mm thickness in melamine

finish. The PVC edge band will be confirming to to IS 4892 standards. Edge band used have good resistance to light fastness, impact resistant

and highly resistant to heat and solvents.2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The edge band

material should have Shore D hardness of 79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality

certification confirming to ASTM D 4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded with matching

finish or have an option of reverse water fall edges.

Support - The PLB Gable end supports are offered in both 18 mm PLT (laminated in the same finish both sides). The PLB will be confirming to

IS 12823 : 2018. MS leg support should confirm to IS 4923 : 1997, IS 3074.The table top shall be supported on particle board base gable end.

The end and mid wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board

and the profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which

provide structural support for the table. The modesty panel shall be 18mm thick pre-laminated particle board with appropriate PVC edge

banding connected with both end. Wire carrier shall be provided below the table top for power connection having size 60mm X 125mm made of

0.8mm thick high yield strength of CRCA sheet of grade 'D' confirming to IS:513 with duly powder coated. There shall be buffers provided at the

base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. meeting long

time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per Indian standard. Product

should be BIFMA Compliance.

MEETING ROOM TABLE CIRCULAR

SIZE:-1350MM@DIA X 750HT

SPECIFICATION:-

Table top - The work surface will be in PLB 25mm thick one side pre-laminate board confirming to IS-14587:1998. The

density of PLB will be 680kg/m³. Surface: CPL( continuous pressure laminate) in 0.5mm thickness in melamine finish. The

PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

12823:1990.PVC edge band will be minimum 2 mm thick, will be imported, quality confirming to DIN 68861, 53388

standards. The edge band will be fixed to the work surface edges all round with Imported Hot melt Glue confirming to ISO

9001- 2008 and certified by ANSI for quality.

Under Structure - • The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor

undulations- +/- 20 mm. ERW Tube confirming to IS 4923 : 1997 – 16g. Main leg members will be connected through a

horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be

fabricated using Argon & Co2 gas mixture on a Robotic welding machine to ensure adequate welding strength with

consistency.• The legs will be connected with Cross beams to take care of the bending stress catering.• The number of cross

beams will be based on the depth of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16 g.

• The Engineering plastic components will be made with Acrylonitrile butadiene styrene (ABS) which are confirming to ASTM

D256 for Izod Impact (1/4”) for Leg shoe and levelers.

Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.Cable Trays will be provided

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

CHAIR FOR MEETING ROOM AND CONFERNCE ROOM

SPECIFICATION:-

Chair's Seat and back is made out of 9 layer 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-

nuts and revited in to the wood.Gaslift - Class 4 tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm

dia castors compling to ANSI / BIFMA X 5.1 – 2002.Specially designed metal base 5 pronged structure forged out of CR

Sheets of 2 mm thick. Base of diameter 26 inches for complete stability, extreme durability, sturdiness and pleasant aesthetic

looks. Reinforced with CO2 welding to provide additional strength and support. Tested prudently and rigorously as per

ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards.Upholstery: Seat Cushion with pre moulded foam of 50 - 60

density Density -- 52 kg/m3 Hardness -- 12.6kgf at 25%.Distinctively and characteristically designed tilt mechanism offering a

very smooth and fluidic reclining motion with tension adjust knob and importantly offering seat to back recline ratio of 3:7,

optimal for good back support.Multilock mechanism is fabricated from CR Sheets, undergo through CO2 welding process

imparting uniform surface finish and tensile strength. The components are processed with high degree of precision and care

so as to assemble with other parts in perfect harmony to give smooth and effortless reclining experience. Tension springs

are made out Grade II material conforming to Indian Standards. Also provided with release levers for locking mechanism and

height adjustment of seat. Mechanism aides to operate the height adjustment, and has been equipped with 4 locking

positions, back rest “ Return Prevention” function. Back Frame is inserted with Mesh & Adjustable Lumbar Support.Tension

control is below the Seat.Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long Moulded self skinned

polyurethene Arms confirming to IS 7078 with steel insets for long life.one way adjustable - Height Adjustable.Seat is duly

WORKSTATION WITH PEDESTAL

SPECIFICATION:-

Table Top - All table tops will be made out of PLB will be E1- P2 25mm Pre-laminated particleboard (PLB) confirming to IS-

12823:2018 with 2 mm PVC edge banding. The table top will be made in PLB( Pre laminated board) with the density of

680kg/m³ and 25mm thick one side pre-laminate board confirming to IS-12823: 2018. Surface: CPL( continuous pressure

laminate) in 0.5mm thickness in melamine finish. The PVC edge band will be confirming to to IS 4892 standards. Edge

band used have good resistance to light fastness, impact resistant and highly resistant to heat and solvents.2 mm thick PVC

edge band will confirm to DIN 68861 for resistance to clearers. The edge band material should have Shore D hardness of

79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification confirming to

ASTM D 4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded with matching finish or

have an option of reverse water fall edges.

Support - The PLB Gable end supports are offered in both 18 mm PLT (laminated in the same finish both sides). The PLB

will be confirming to IS 12823 : 2018. MS leg support should confirm to IS 4923 : 1997, IS 3074.

Wiremanagement - Cable management.The system should have effective Cable management system. The data and the

power cables should be at different levels (called Raceways) to maintain the separations as per the IT norms minimum 300

mm apart. The wire management slots in the frames are large enough to manage high volume of data cables (CAT-6) -

approx- 40-50 CAT-6 cables. Vertical movement of the cables in addition to the two/ three levels of horizontal passage

should be possible. The raceway covers should be designed as “clip on” raceway which permits easy removal and fixing. No

screws/nut bolt should be used. The Skirting raceways are 120 mm and the raceways at the table top level are of 120 mm.

The length of the raceways will be matching to the frame width. All standard electrical/Data faceplates should be capable of

being be mounted on the raceways at both the levels. The raceways will be provided with cut outs as per the requirement of

the switches/sockets. The switches /sockets to fixed fixed “staggered” to ensure electrical safety. Option of additional

15 raceway should be available to accommodate more cables (if >50 CAT-6 cables) or sockets.

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

15 raceway should be available to accommodate more cables (if >50 CAT-6 cables) or sockets.

PARTITION:-The partition based system will be with main spine in 50 mm thick made by 1,2 mm thick CRCA sheet

confirming to IS 513: (2008), IS 13871:1993. The end and intermediate spines could be 50 mm or with an option of 33 mm

thick. The profile of verticals should be able to slide the tiles thickness of 6 mm. The verticals will have multiple slots for

carrying the data and power cables and provision for fixing MS brackets.There will be minimum three slots at different levels

to accommodate raceways at skirting and table top levels. There should be options of carrying the cables both above and

below the table top as per the requirement. The slot provided should be of size- 150x 25 mm. the slot cut out should made by

CNC machines to avoid sharp edges and burr. There will be minimum four horizontal members in each frame- top , middle

levels and at the skirting level. The horizontal members will be made from CRCA sheets formed in “C” shape in hydraulic

press. The CRCA sheets will be confirming to IS 513: (2008), IS 13871:1993.All the Frames are duly powder coated in

charcoal black color or color of choice to a thickness of 50-60 microns confirming to ASTMB – 117, ISO – 1520 and ISO –

1518 & ASTMD - 2794. The powder coating will be done with NANO Ceramic coating.All the Frames are duly powder coated

in charcoal black color or color of choice to a thickness of 50-60 microns confirming to ASTMB – 117, ISO – 1520 and ISO –

1518 & ASTMD - 2794. The powder coating will be done with NANO Ceramic coating.

Workstation is provided with Fabric Magnetic, Glass Marker and Laminate tile.

• Glass Marker tiles: 5mm Glass with white Vinyl Backing. The glass will confirm to ASTM C1036.

• Laminate Tile: Constructed out of 6mm thick Pre-laminated Particle board confirming to IS – 12923.

• Fabric Tile: Constructed out of 5.5mm thick Medium Density Fiber Board (MDF) confirming to IS – 12406 and covered with

Fabric of choice. The fabric used will be confirming to BS EN 1021-1, BS 7176 & ISO 105-B02. The glue used for

upholstery are made with advanced adhesives confirming to ASTM D 1500, ASTM 1298 standards. Sprayed with upgraded

machines to ensure uniformity and best adhesion.

• Magnetic tile: Constructed out of 0.8mm Galvanized sheet confirming to IS 277, ASTM A653 specifications. Sheets are post

treated with NC (Noncromat coating - Cr free coating) and covered with Fabric of choice. The fabric used will be confirming

to BS EN 1021-1, BS 7176 & ISO 105-B02. The glue used for upholstery are made with advanced adhesives confirming to

LINEAR WORKSTATION

SIZE:-1200W X 600D X 1200HT

L-SHAPE WORKSTATION

SIZE:-1500/1500W X 600D X 1200HT

CHAIR FOR WORKSTATION

SPECIFICATION:-

The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in

OCP-QLTA-P14-18

and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0

cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x

0.2±0.016cm thk. MS

16 ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric 37 NOS ₹ 9,261.00 ₹ 342,657.00

with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density=45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one piece armrests shall be injection

moulded from black Co-polymer Polypropylene. The mechanism shall be designed with 360° revolving type, 17±2° maximum

tilt m pivot at centre,

Upright position locking., Tilt tension adjustment. The pneumatic height adjustment shall has

an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection

moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass filled Nylon66 and fitted with 5

nos. twin wheel

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

SPECIFICATION:-

The storage will be made in 18 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick one side pre-

laminate board confirming to IS 12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm thickness in melamine

finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

17 12823:1990.The back of storage will be made in 9 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm

thick one side pre-laminate board confirming to IS 12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm

thickness in melamine finish. Storgage will be provided with edge banding 2 mm thick PVC edge band will confirm to DIN

68861 for resistance to clearers. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality

certification and confirm to ASTM D 4499 standards for viscosity and thermal stability. The edge band material should have

Shore D hardness of 79± 4. storage will have two adjustable shelves making 3 compartments.The shutters are fitted with

HThinges.Central

STORAGE locking system , levellers & other necessary hardware are priovided.Handles will be hand

MEDIUM HT STORAGE

MEDIUM HT STORAGE

RECEPTION TABLE

SIZE:-2400W X 750D X 1050HT

SPECIFICATION:-

RECEPTION TABLE with 900mm L Acrylic counter

Specifications - Made up of prelam particle board

Prelam hanging drawer 2 Number

CHAIR FOR RECEPTION

SPECIFICATION:-

The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in

OCP-QLTA-P14-18

and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0

cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x

0.2±0.016cm thk. MS

ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric

19 with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR 2 NOS ₹ 9,261.00 ₹ 18,522.00

polyurethane foam shall be moulded with density=45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one piece armrests shall be injection

moulded from black Co-polymer Polypropylene. The mechanism shall be designed with 360° revolving type, 17±2° maximum

tilt m pivot at centre,

Upright position locking., Tilt tension adjustment. The pneumatic height adjustment shall has

an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection

moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass filled Nylon66 and fitted with 5

nos. twin wheel Digitally signed by AMIT

castors. The pedestal is 66.3 ±0.5cm. pitch center dia. (76.3 ±1.0cm with castors). The twin wheel

10 shall be injection

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

SOFA 2-SEATER FOR RECEPTION AREA

SPECIFICATION:-

Seat Foam: the sofa is made up of fine quality leatherette.The structure is made up of silver wood and pine wood.The Seat is

made of PU Foam with Density 32 to 40 +/- 2 kg/cu .mtr Seat is upholstered wuth Leatherite.Back Foam: The Back is made

of PU Foam with Density 32 to 40 +/- 2 kg/cu, Backis upholstered with Leatherite.Unterstructure is made up of silver wood or

pine wood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Legs

20 should be made up of solid wood having pu matt finish. 1 NOS ₹ 39,482.10 ₹ 39,482.10

CENTER TABLE FOR WAITING

SPECIFICATION:-

Center table with an overall size L 1200 X W 600 X H 425 mm. The top of the table shall be made up of 12mm thick

toughened glass. The top profile shall be in square shape with bevelled edges. The top shall be supported on vacuum caps

situated over SS 202 grade pipe frame. The under structure shall have SS with shiny chrome finish pipe frame having dia.

20-25.4mm with 2mm thick. There shall be good quality PPCP shoe provided to avoid scratches on the floor.Top glass is

partial tempered glass.

CORNER TABLE FOR WAITING

SPECIFICATION:-

Corner table with an overall size L 600 X W 600 X H 505 mm. The top of the table shall be made up of 12mm thick

toughened glass. The top profile shall be in square shape with bevelled edges. The top shall be supported on vacuum caps

situated over SS 202 grade pipe frame. The under structure shall have SS with shiny chrome finish pipe frame having dia.

20-25.4mm with 2mm thick. There shall be good quality PPCP shoe provided to avoid scratches on the floor.Top glass is

partial tempered glass.

TABLE SIZE: 1800W X 900D X 750HT

Specifications:

For Cafeterias - 18mm thk prelaminated Hydrosheild table top/ ISO Table top.

For Office / meeting tables - 25mm thk prelaminated particle board with 2mm edge banding finishSupport:

End Legs: Chrome Finished understructu

Digitally signed by AMIT

SL NO DESCRIPTION/ SPECIFICATIONS QTY UNIT UNIT PRICE AMOUNT

SPECIFICATION:-

Chair is molded from GF 20% Polypropylene conforming to ASTM D 638 STD & Complying to ROHS. Seat & back design

will be integrated as a single unit. The chair shall be injection molded with 2500 tonnage press. The chair should weigh about

3.9 kg. The back will be designed with triangular structural trusses & narrowed at the top to provide strength & comfort to the

chair with good air circulation to the user. The back should be designed to provide ergonomic comfort with precise curvature

25 to offer good lumbar support. The seat profile should be designed with water fall to provide necessary comfort in popliteal 16 NOS ₹ 2,744.10 ₹ 43,905.60

The design of the chair will be provided with four U shaped legs ensuring good strength to the chair. Chair shall be tested for

minimum load bearing capacity of 150 KG. The design should have the capability to stack.Chair should be BIFMA and Green

Guard certified.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES-ART WORKS

S NO MR DESCRIPTION UNIT QUANTITY RATE

DSR (INR) NON DSR (INR)

Providing and fixing theme artwork/ any other as per direction and

site requirement from the local artisans as per the selection of the

1 MR client and the architect.

Panels of various sizes No. 15 3000.00 45000.00

TOTAL ART WORKS 0.00 45000.00

Digitally signed by AMIT

Schedule of Quantities: Signages

S No Description Unit Qty Unit price

1 RECEPTION 3D ACRYLIC SIGNAGE

Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of

required size and shape with arrangement of screws in the letters itself for

mounting on the walls or pasting using Tape. Fixing complete as per

directions of the engineer. The sizes would be calculated in Sqft as per Logo Each 1 25,624.00 25624.00

Design provided.

Tentative Size 42"x60"

2 NAME SIGNAGE CHANGEABLE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with textured

wood finish pasted /White milky acrylic 3mm laser cut pasted on top with

proper names/ Departments written using plottercut vinyl or laser cut acrylic

letters in approved colour.Inserting provision for changing names .Fixing Each 13 1,281.00 16653.00

provision using double sided tape as required.

Signage Size 12"x5"

3 TOILET ICONS

Providing and fixing of Acrylic signage made of 5mm Acrylic with textured

wood finish pasted /White milky acrylic 3mm laser cut pasted on top with

proper icons using plottercut vinyl or laser cut acrylic letter in approved colour. Each 3 1,025.00 3075.00

Fixing provision using double sided tape as required.

Signage Size :8"x8"

4 FIRE SAFETY SIGNAGE

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun board

sheet at base with photoluminescent film self adhesive & colored vinyl (

Red/Green) Plotter cut and pasted on top. Both side / Single Side facing

Complete including fixing on wall with screws and washers or hanging on

ceiling with GI chain/GI Bar complete as per technical specifications and

a directions of Engineer.

Photoluminescent, Fire Hose Reel - 10"x8" Each 1 384.00 384.00

b Photoluminescent, Fire Exit / Escape Sign - 18"x6" Each 1 384.00 384.00

c Photoluminescent, Floor Level - 18"x6" Each 1 384.00 384.00

d Photoluminescent, Fire Alarm Call Point - 10"x8" Each 1 384.00 384.00

e Photoluminescent, Fire do not use lift- 10"x8" Each 1 384.00 384.00

f Photoluminescent Signs, Fire Extinguishers - 10"x8" Each 3 384.00 1152.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: HORTICULTURE

S NO DESCRIPTION Qty Unit Rate DSR AMOUNT NON DSR AMOUNT

Supply and Planting Lolina plant having 2-3 ft height with Coco-

peat, mud and manure complete.

Supply and Planting Seaforthia Palm having ht. 90cm to 1.20 m

2 with 6-8 suckers, well developed, fresh and healthy lush green 10 Each 1500.00 15000.00

leaves from bottom to top complete.

Supply and Planting Rhapis Palm having ht. 90cm to 1.20 m with

3 15 to 18 equal suckers, well developed, full of fresh and healthy 10 Each 1500.00 15000.00

leaves from bottom to top complete.

Supply of full soil fill conical shaped planters of specified volume

and dimensions in stone finish or equivalent. planters to be

indigenously made by rotational moulding, with homogeneous

recyclable, industrial grade polymer-resin mix, and textured

surface. planters should have an integrated water outlet hole &

4 plug, single layered peel-proof construction, light weight, rust

proof, uv stabilized, anti-frost feature without any joints, and

easy to clean. planter supplier must give 1 year warranty against

any fading or cracking for both indoor and outdoor use. green

plant and laying is extra. potting instructions as per company

5 Artificial Vertical Garden on wall 10 Sqm 2562.00 25620.00

Supply and installation of Natural Plants with sand, fertilizer etc.

Digitally signed by AMIT