PROVN OF CONSTRUCTION OF EQUIPMENT ROOM BATTERY ROOM RADIO RECEIVER ROOM CIPHER ROOM AND STORE ROOM ALONGWITH TOILET AT 2 UD DETACHMENT OF 60 WEU AND PROVN OF ONE GUARD REST ROOM AT HANUT COLONY AND PROVN OF COMPLETE REWIRING ALUMIMIUM TO COPPER IN B

Amount

Excavation in trenches , n exc 1.5m wide and n exc 1.5m in depth for wall foundation etc or for shaft, well, cesspits, manholes, pier holes etc n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified.

M & L PCC 1:4:8 Type D2 using 40 mm thick greded stone aggregate as in foundations,filling and mass concrete complete all as specified.

M & L brick work with fly ash bricks (old size) straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified.

Removing excavated material n.exc 50 mtr & depositing where directed at a level n.exc 1.5 mtr above/below the starting point.

M & L 40mm thick Damp proof course to horizontal or vertical surface incl necessary formwork with PCC 1:2:4 type B-0 & mixing of water proofing compound as per manufacturer's instructions complete all as specified.

Supply only of integral water proofing powder complete all as specified.

Earth filling under floors or in foundation incl watering, ramming and consolidation complete as directed.

M & L for design mix RCC M-25 (20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified.

M & L for design mix RCC M-25 (20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified.

M & L for design mix RCC M-25 (20 mm thick greded stone aggregate) in slab supported on walls, beams and coloums in roofs, floors, balconies, canopies desk slabs and in selves etc complete as specifed.

M & L for M-25 (20 mm graded stone aggregate) design mix in beams, chajja, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter complete all as specified.

M & L for formwork to sides of pillars, posts, struts, piers,columns, and stanchions complete all as specified.

M & L formwork to sides and soffits of floor or roof beams, chajja, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M & L for form work in soffits of suspended slabs such as roofs slabs, landing,and similar work not exc 200mm thick flat finished rough to obtain plaster complete all as specified.

M & L for form work to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide complete all as specified.

M & L for Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to cmplete as specified.

Ditto all as per item no 18 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified.

M&L for 10mm thick rendering (screeding) over roof slab in CM 1:6, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished fair & even, complete all as specified and as directed. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.

Supply only liquid water proofing compound ISI Mark complete. Make: Dr. Fixit or Equivalent.

M & L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 litre/sqm and provide a layer of APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) laid on primed surface complete all as described in Para 11.44.5 of SSR Part-I, complete all as specified and as directed. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps.

M & L for Lime concrete terracing in roof with minimum thickness at edge 40 mm and increasing uniformly towards ridges to obtain a chain slope of (1:40) as described in Para 11.27.2 of MES Schedule Part-I complete all as specified & as directed.

M & L for 40 mm thick brunt clay brick tiles bedded on cement mortar and joints grouted flush in cement and sand mortar (1:3) mixed with integral water proofing compound IS 2645 : 2003 @ 3% by wt of cement as complete all as specified and as directed.

M & L for 5 mm thick cement plaster in CM 1:3 on concrete surface of ceiling finished even and smooth complete all as specified and as directed.

M & L for three coats of white wash on roof ceiling including preparation of newly plastered surfaces complete all as specified.

M & L cement plastering 15mm thick in CM 1:6 on other than fair face of brick work surface finished even & smooth w/o using extra cement complete all as sepcified.

M & L for two coats of distemper oil emulsion on walls on newly plaster surfaces of walls incl preparation of surfaces and a layer of wall care putty with primer complete all as specified.

M & L cement plastering 15mm thick in CM 1:4 on other than fair face of brick work surface finished even & smooth w/o using extra cement complete all as specified.

M & L for two coats of cement base paint over a coat of priming coats including preparation of new plastered surfaces complete all as specified and as directed.

M & L 75mm thick PCC 1:4:8 type D2 using 40 mm thick graded stone aggregate as sub base in floors all as specified.

M & L 25mm thick PCC 1:2:4 Type-B0 using 20 mm thick graded stone aggregate as in flooring complete all as specified.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M & L for non Skid ceramic tiles 7 to 8mm thick (squares/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in CM 1:4 complete all as specified.

M & L Glazed ceramic colour tiles of size 300x450x7mm thick as in dado/ skirting jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 10mm thick screeding/ bed plaster in CM 1:4 complete all as specified and directed.

M & L for acid resistant tiles 15mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors over and incl a layer of 15 mm thick screed bed in CM 1:4 complete all as specified.

S & F Steel windows box type with side hung shutters including projecting type hinges with steel handles and steel pay stay, complete with glazing bars/without glazing bars, dovetailed or welded complete all as specified.

S & F box type steel ventilator with top hung shutter including hinges steel peg stay complete.

S & F M S Guard bars of 10mm square bars welded to steel frame of windows complete all as specified.

M & L preparation of steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exec 0.5 sqm in each pane.

S & F 4mm thick sheet glass pin headed type and glazing with oil putty in square n exec 0.5 sqm in each pane.

S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S & F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per specification.

S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, including making good the disturbed surfaces of wall etc in CM 1:4, complete as specified & as directed.

S & F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, including making good the disturbed surfaces of wall etc in CM 1:4, complete as specified & as directed.

M & L PCC 1:3:6 type C-1 using 20mm graded aggregate as in bed blocks etc for fixing windows, doors frames or other structural section as directed.

S & F 35mm thick Second class hardwood factory made plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete.

S & F 2nd class HW 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauge etc (w/o sash bars) complete all as specified.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

M & L for preparing new or previously untreated surfaces of wood and wood based materials of any decription exceeding 10 cm in width or girth when un-connected with other painting or when painted in different tint and applying two coats of synthetic enamel paint over & including a coat of pink primer complete all as specified.

Supply & fixing 100 mm MS butt hinges medium weight cold rolled mild steel complete all as specified.

S & F 100 mm aluminium Butt hinges, extruded aluminium alloy, with galvanised mild steel hinge pin, anodised and fixed, type B-21 and will be fixed to the frame with stainless steel screws with triangular head all as spd and dircted.

S & F aluminum cast type handles 150mm size complete all as specified.

S & F 200mm long alumimium barrel tower bolts extruded section complete all as specified.

S & F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300 mm

S & F galvanised steel tubing medium grade 15mm bore fixed to walls or laid in floors,walls complete all as specified.

S & F galvanised steel tubing medium grade 20mm bore fixed to walls or laid in floors,walls complete all as specified.

S & F in repairs, vitreous china squatting pan “ORISSA” pattern size 580x440mm white with integral foot rests including connection to trap, and to flushing pipe, etc. complete including making good to floor alongwith flush pipe and P-trap complete all as specified.

S & F wash hand basin vitreous china size 550x400mm white flat back including waste, chain plug, PVC connection, PVC waste pipe complete all as specified.

S & F for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe,grating and union for discharge pipe and all fitting.

S & F PVC low level flushing cistern.valve .less, syphonic action type 10 liters capacity with inlet, ball valve, float and handle with including brackets and PVC bend pipe 90cm long etc. supplied and fixed.

S & F rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) Double layered ISI marked hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, all as specified.

S & F Ball valves 20mm bore high pressure of PTMT with epoxy coated alum rod and high density plastic ball screwed for iron pipe and fixed.

S & F CP Bib taps cast copper alloy fancy type with crutch or butterfly handle screwed for iron pipe of 15mm bore and fixed.

S & F tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between flanges and fixed complete all as spd and directed.

S & F pillar tap cast copper alloy fancy type screwed for iron pipe on both ends of 15mm bore and fixed.

S & F in repairs, 15 mm bore chromium plated concealed type stop valves cast copper allay, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes complete all as specified.

S & F Stop cock cast copper alloy with crutch or butterfly handle screwed for iron pipe on both ends of 20mm bore and fixed.

S & F Chromium plated 80 mm long shower rose with or without swivel joints, any size, incl fixing to steel pipe or union as in repairs.

S & F 15 mm bore chromium plated angle cock cast copper allay, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes.

S & F PVC connections 15mm size with brass nuts of length 450mm complete all as specified.

S & F PVC (SWR) pipe of 100mm bore fixed to wall or laid in trenches complete as specified and as directed.

S & F PVC (SWR) pipe of 75mm bore laid in floors or trenches complete all as specified.

S & F PVC (SWR) bend any radius of 75mm bore jointed with solvent cement

S & F PVC (SWR) junction double (Single tee) of size 75mm bore jointing with solvent cement.

S & F PVC (SWR) floor trap plain with grating including jointing with solvent cement of size 75mm outlet.

M & L for framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S & F built in almirah of large size complete all as specified & as directed by Engr-in-Charge.

S & F powder coated aluminium snap grid frame work of size 605 x 605 mm for false ceiling including necessary notching. The snap grid shall consist of powder coated aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with powder coated aluminium angle of size 35 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 6 mm thick gypsum boards of Make Everest or euivalent. (designer/ pattern shall be as approved by the Engineer-in -charge) boards in grid fixed as false ceiling grid made of aluminium as per specification incl 6 mm dia MS round bar as in suspension to support snap grid.all as specified and as directed.

Demolition of stone/boulder masonry, built in cement mortar or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles incl removing from site complete all as specified.

M & L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed

M & L plinth protection 75mm thick PCC 1:3:6 C1 on 75mm thick PCC 1:5:10 E2 on rammed earth as directed.

M & L sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all as specified and directed.

Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid, including intercepting chamber, screen chamber Brick work in CM, Stone patti cover slab, filling with brick bats complete of size 1.80 M dia X 3.0 M deep complete all as specified and as directed.

M&L concrete bed to drain pipe in PCC 1:4:8 type D2 using 40mm graded stone aggregate incl packing under and hunching against sides of pipe after they are laid on slope and tested for 150mm dia bore sewer pipe line ( earth work excavation and sewer pipe line will be measured and paid separately)

Supplying and laying salt glazed stoneware pipe confirming to IS 651-1972 in tranches and jointed in cement mortar 1:1 complete all as shown on drawings for 150mm internal dia of pipe ( excavation and earth work measured separately)

M & L precast cement concrete but in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces Type B1 1:2:4 (20 mm graded aggregate Set in Cement Mortar 1:4 complete all as specified.

Surface excavation (not exceeding 30cm deep) and averaging 15 cm , getting out in any type of soil.

Excavation in trenches for foundation etc not exc 1.5m wide and not exc 1.5 m in depth in any type of soil all as specified.

Form work to edges of concrete flats, breaks ,conc railing nexc 200mm wide finished roughthick

M&L for Reinforced cement concrete M-25 design mix as in chajjas incl necessary formwork and the like, all as specified and directed by Engr-in-Charge.

M&L for TMT bars 6mm to 8mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for 75 mm thick plain cement concrete typeB-2 ,1:2:4 , using 40 mm graded crushed stone aggregate as in flooring finished even and smooth w/o using extra cement

M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified.

M&L for machine cut kota stone 16-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry over and including 10mm thick rendering in CM 1:4 ,mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and 5 mm thick in CM 1:4 as second layer incl. mixing water proofing compound and finished fair and even without using extra cement.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges where directed and providing 6 mm thick joints through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 grade and three parts of fine sand (all by weight) complete.

S&F factory made mild steel Window box type with side huge shutters incl pintol hinges,steel handles, steel peg stay and all locking and with glazing/wire mesharrangement and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n exe 0.5 sqm each pane all as specified

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and avg width of aperture1.18mm

S&F 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.

S&F 150mm size extruded aluminium handles fabricated type, anodised and fixed.

S&F mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with and incl. A minimum of 6bolts and nuts four on bolt plate and two on staple plate of 250mm long.

300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F PVC (SWR) pipes 110mm bore single sockted in any length with rubber rings joints fixed to walls as in rain water pipe.

S&F 110 mm bore PVC (SWR) bends with and incl oval acess any radius

Stack clamp out of 50mm x5mm flat iron/ PVC stays including bolt and nuts and securing ends of stays to walls or roof for 50mm bore piece.

S&F stainless steel Peg Set of Six of standard size (not less than 300mm long) fixed to wall with two rawl plugs and chromium plated brass screws complete all as specified & as directed. Make :- Cat Part No BEA-30 of make – Prayag or equivalent in makes mentioned in Appendix 'B' here-in-after.

Preparing surface of wood of any description over 10cm width ot girth and applying two coats of synthetic enamel paint.

M & L ANTI-TERMITE TREATMENT with Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area .

M & L ANTI-TERMITE TREATMENT with Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured).

M & L M & L ANTI-TERMITE TREATMENT with Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface.

M & L M & L ANTI-TERMITE TREATMENT with Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area.

M&L for framed works as in stairs including stringers, treads, hand rails etc including cleats, brackets etc complete.

S&F anodised aluminium alloy harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.

Supply only M S Chromium plated Brackets for Curtain rails including screws etc.

Supply only M S /PVC chromium coated Fancy type Globes for Curtain Rods.

M&L for 80 mm thick machine pressed precasted conc interlocking tiles/paver blocks any shape size conforming to IS 15658-2006 of M-40 grade laid over and incl 25mm thick sand cushioning with grey cement or mixed with pigment .

S&F MS Work in detached work such as for mosquito nets, straining bolts nuts washers and G I wire etc and fixing to straining bolts, hooks, eyes, etc.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed.

Taking down submain wiring Aluminium/ copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed.

Taking down old U/S existing DB TPN 4 way and DB SPN 8 way including MCB/MCCB of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of PVC concealed conduit with accessories with laminated top cover fixed on GI sunken box with cover plate for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling ,including paitnt,etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge for the following :- (a) One Light/fan/ex-fan point controlled by one switch.

(b) One 3 pin 5 amps socket on independent board.

(c) One 3pin 5 amps socket point on the same board complete

Ditto all as per item No 126 above but with 2.5 sqmm copper wire for 3 pin socket outlet 15 Amp on independent board complete and all as directed by Engr-in-charge.

Ditto all as per item No 126 above but with 4.0 sqmm copper wire for 3,5 pin socket outlet 15 Amp on independent board complete and all as directed by Engr-in-charge.

S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

Supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

Removing and Refixing LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed by Engr-in-charge.

S&F sheet metal enclosure MCB DB, double door, vertical TPN 4 way with 200 Amps rated busbar all as specified and as directed. Make:- Hegar/Legrand/Seimens

S&F sheet metal enclosure MCB DB, double door, vertical TPN 8 way with 200 Amps rated busbar all as specified and as directed. Make:- Hegar/Legrand/Seimens

S&F MCCB 100 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

S&F MCCB 200 amps, 4 pole, 415 volts, Adjustable type breaking capacity 36KA complete all as specified and as directed by Engr-in-charge.

M&L for submain wiring using 2 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 2runs of 6 Sqmm of voltage rating 1100V for Single phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-2 runs of single core FRLS PVC cable 6sqmm for Single phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit)

M&L for submain wiring using 4 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 4runs of 10 Sqmm of voltage rating 1100V for three phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-4 runs of single core FRLS PVC cable 10sqmm for three phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit)

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70sq mm 3.5 core complete all as specified and directed.

Taking down Exhaust fan,sealing cable end,dismantling blades and removing fan and blades & refixing Exhaust fan of any make, any sweep , keeping side in store in safe custody for painting of Exhaust fan complete,in situ with synthetic enamel paint byspraying including filling cavities with filler,one coat after cleaning all dust and reassembling the fan complete including writing MES No at the site.

Taking down fan,sealing cable end,dismantling blades and removing fan and blades & refixing ceiling fan of any make, any sweep , keeping side in store in safe custody for painting of ceiling fan complete,in situ with synthetic enamel paint by spraying including filling cavities with filler,one coat after cleaning all dust and reassembling the fan complete including writing MES No at the site.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16sq mm 4 core complete all as specified and directed.

S&F switch piano type, 5 Amp, single pole one way, 230 Volts, flush type complete all as specified and as directed by Engr- in -charge.

S&f Switch piano flush type single pole, one way 15/20 Amps 230 Volts complete all as specified & directed by Engr-in-Charge.

M&L socket outlet 3 Pin 5 Amps flush type 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L for socket outlet 2 in 1, 3 Pin, 5 & 15 Amps, 230 Volts t complete all as specified & directed by Engr-in-Charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.HAVELLS CAT PART NO-ENDURALINEARNEOBS10WLED865SPCWH/WIPRO CAT PART NO-LL20-111-XXX-65NE3/BCLSB 10 WH

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W.

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings .

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SPN, 6-32 Amps, 240 volts, breaking capacity 16KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB SP, 6-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

supply and fixing fan regulator electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as directed by Engineer-In-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-charge.

Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

S & F water heater storage type 25 Ltr capacity, BEE 5 star and 8 bar pressure rated stainless steel (minimum wall thickness 2 mm) tank with feroglass coated inner container energy saving high density PUF insulation vertical ABS shock proof plastic body grouting of studs in wall in cement motar (1:3) nuts, washers, provision of two Nos PVC braided connection 450mm long heavy duty with brass nuts and two Nos brass chromium plated angular valve,thermostate,NRV ,TOP PLUG 20AMP with valve flange suitable for 15mm bore pipe for water supply connection complete. Make : Havells (Model -Monza EC) Cat part No GHWAMFSWH025/Bajaj calenta storage/Cromton solarium Qube

Supply & Fixed on walls and ceiling or laid in floor/in tranch and jointing GI tubes, 15 mm dia medium grade in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in wall complete all as specified and directed by Engr-in-charge .

supply and fixing Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F MCCB 63 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

M&L for submain wiring using 4 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 4runs of 6 Sqmm of voltage rating 1100V for three phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-4 runs of single core FRLS PVC cable 6sqmm for three phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit)

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380 mm sweep with, blades, and frame and louvers

S&F MCCB125 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

M & L for submain (single phase) wiring complete with and including 4.0 sqmm two single core, fire retardant, PVC insulated and unsheathed multistranded copper conductor cable, 1100 Volts grade, drawn through PVC conduit of suitable size including accessories and fixed on walls and 2.5 sqmm, fire retardant, PVC insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by Engr-in-Charge. Note :- (i) Two runs of 4.0 sqmm PVC insulated wire and one run of 2.5 sqmm wire and one run of PVC conduit shall be measured as one unit length. (For MCB DB SPN Circuit)

M&L for copper electrode chemical earthing with high conductive ,corrosion resistant ,CPRI tested and CE certified maintenance free chemical earthing pit (pipe in pipe technology based) in which primary conductor (pipe) having 40 mm dia and Secondary conductor and between secondary and primary conductor of earthing electrode crystalline compound is to be injected .The length of this electrodes is min 3000mm (3 Metre) having 45 kg of ground enhancement compound, it contain a homogenous mixture of conductive cement ,electrolyte carbon , hydrous Aluminium cilicate and other electrolyte compound complete and 60 Kg contain a homogenous mixture of conductive cement,Coal powder ,electrolyte carbon , hydrous Aluminium cilicate and other electrolyte compound . Filled in earth pit of bore hole of 200 to 250 mm dia and depth up to 6.15 metres min length of electrode will be increase with connecting of 32x6 mm copper strip and extra up to 7.50 metres, and total depth of earthing electrodes in min 6.15 metre for achive resistance valve less than or equal tob1.0 Ohm including RCC earth pit cover having 450x 450 CL chamber with handle 6 mm dia and arrangement ,funnel with wire mesh complete as per direction of Engr in Charge.

Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m width for laying of cable lines etc and getting out in hard/ dense soil complete all as specified.

Supply and laying Sand coarse dry as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 cm (15 cm under the cable & 8 cm over the cable) and gently punned down to 18 cm thickness all complete as specified and as directed.

Supply and laying bricks (old size) for cable protection by using common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry flat across length of the cable with width of the trenches equal to length of bricks and all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6sq mm 2 core complete all as specified and directed.

S&F GI tubing light grade 40mm dia for protection of cable on pole/ wall etc complete all as specified and as directed by Engr in charge.

Supply and fix copper wound voltage stabiliser of 4 KVA capacity for automatic operation , single phase naturaly air cooled indoor type and designed for input variation between 170 to 270 volts with out put voltage stabilised at 230 volts with accuracy +/- 1% , Operating frequency 50 Hz.

Supply and laying galvanized steel water tubing medium grade of 25 mm bore with & including all fittings complete, complete all as specified and directed.

S&F 25 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, icomplete all as specified and directed by engr -in- charge.

S&F brass valves ,high pressure ,with polythene float and flynut complete ,screwed both side ends for iron pipes or brass ferrule and fixed complete all as spoecified and directed.

Boring of holes under road , pavement , hard standing by trench less technology using ultra sounding technique and necessary machine including all accessories as required as per site complete all as specified.

Supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 40 to 100mm bore GI/DI water pipe line including drilling and welding of 25/50mm G I socket and necessary rubber insertion, nut, bolts & washers complete all as directed.

ALPHA ENGINEERING COMPANY

SUBHAM ENTERPRISES