PROVN OF TOILET BLOCK IN TRG AREA AT PW DIV URINAL IN TRG AREA AT SW DIV DRAIN AT DEO OFFICE PARKING SHED AT BUNGLOW NO 45 AND ADDN ALTN TO PLUMBING WORKS AND CONNECTED ITEM AT CERTAIN YOS WING ACCN UNDER GEMIS MHOW

Amount

Surface excavation n.exc 30cm deep and avaraging 15cm deep and getting out in any type of soil.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5m depth for foundation, for shafts,wells cesspits, manholes, pier holes, etc n.exc 10Sqm on plan & n.exc 1.5m in depth & getting out in any soil complete all as specified.

M&L for plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rought finished surface of concrete.

M&L for reinforced design mix concrete M 25 grade in foundation, footings, plinth beam and similar RCC works all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for formwork to sides of concrete flat or curves sides of pillars,posts, struts,piers,columns and stanchions , rough finished surface of concrete complete all as specified.

M&L for reinforced design mix concrete M-25 grade in column, pillars, piers, posts and struts all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for form work to sides and soffits of floor or roof beams haunching, lintel, column, cantilevers shelves includig supported over hangs etc , rough finished flat surfaces of concrete complete all as specified

M&L for reinforced design mix concrete M25 as in beams, cantilevers. brussumers, lintels over 1.50 Span all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for use and waste of formwork to sides and soffits of slab such as roof slab,floor slab,landing and similar work not exceeding 200mm thick , rough fnished surface of concrete flat complete all as specified.

M&L for reinforced design mix concrete M25 as in slab supported on wall , landings, beams canopies, deck slabs and shelves etc complete. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for mild steel TMT bars 6mm to 8mm dia cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

All as per item No 13 above but 5 mm to 10 mm dia as in Stirrups,spaces & binders complete all as specified.

M&L for brick work with fly ash brick using modular size brick, straight or cured on plan exc 6m mean radious built in CM 1:6 complete as specified.

M&L for brickwork with fly ash bricks using modular size brick,straight or curved on plan to any radious in half brick thick walls built in CM 1:4 all as specified

M&L for moorum / red bajri filling in floor or paving laid in layers n.exc 15cm thick spread,levelled and rammed including watering complete all as specified

Returing filling in soil including spreading,levelling watering & well ramming in layers not exc 25cm.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

M&L for hardcore with broken stone or boulders of gauge n. exc 63mm, deposited spread and levelled in layers n exc 15cm thick, watered and rammed to true surface complete all as specified.

M&L for 75 mm thick, PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub base, floor and foot path including necessay formwork etc complete all as specified.

M&L for 40mm thick plain cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in floor, leveling course etc complete all as specified.

M&L for non Skid coloured ceramic tiles 7 to 8mm thick (Square / Rectanguler ) area of each tile exceeding 0.06 Sqm but not exceeding 0.18 Sqm.in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including screed bed or bedding layer in cment mortal 1:6 complete all as specified

M&L for Glazed ceramic coloured tile (glossy series ) of size 300X450mmX7mm thick on vertical surfaces such as dado,skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile including 10mm thick rendering in CM 1:4 all as specified .

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with water proofing compound @ 200ml per 50 Kg of cement, finished even and smooth without using extra cement complete all as specified. NOTE : WPC shall be measured and paid separately under relevant item.

Supply only liquid water proofing compound.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection, finished concrete topping even and fair (without using extra cement) including making joint at every 3 m interval and at corner and filled with mixture of bitumen and sand , laid in alternate bays complete all as specified.

S&F Powder coated anodised aluminium ventilator ( Louvers type) including louver glass and glass stay, section weighing 0.55Kg/m including necessary joining cleats, glazing clips for fixing of wiremesh,rubber neoprene packing,anodised aluminium snap beading screws etc.complete all as specified and directed. NOTE : Minimum thicknes of powder coating shall be 50 micron.

S&F Solid PVC Door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, as per specification and directed.

S& F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F Aluminium, anodised, barrel tower bolts of length 150mm extruded section and fixed

S & F 150 mm long Aluminium handles, cast type, anodised

S&F butt hinges 100mm size medium weight, cold rolled mild steel and fixed.

S&F Aluminium alloy,anodized sliding door bolt of lenght 250mm with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed all as specified.

S&F PVC Pipe 110mm dia single socketed in any length with rubber ring joints, laid in floors all as specified.

S&F PVC (SWR) bend any radious 110mm bore.

S&F PVC (SWR) 110mm bore junction single (Single T)equal or unequal all as specified.

S&F 75mm dia PVC (SWR) multi floor trap plain with grating including jointing with solvent cement

S&F 100X100mm size Salt-glazed stoneware gully trap,square or round mouthed ,type ,P, complete all as specified.

S&F PVC Pipe 75mm bore single socketed,in any length rubber ring joints,laid in floors complete all as specified.

S&F PVC (SWR) bend 75mm bore

S&F PVC (SWR) junction single (Single T) equal or unequa 75mm bore

S&F GI tubes 15mm dia medium grade with all fitting fixed to walls and ceiling or in floor all as specified

All as per Item No 44 above but for 20mm bore

All as per Item No 44 above but for 25mm bore

S& F Gunmetal valve globe or gate valves with iron wheel head,screwed both ends for iron pipe of 25mm dia and fixed.

S&F Rotational moulded polythene water storage tanks three layered of capacity 500 litres (cylindrical vertical with closed top) hoisted and fixed in position completed all as specified.

S&F 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass complete all as specified.

S&F Vitreous china wash down water closet pan ( Pedestal pattern), white (excluding ,flushing cistern and flush pipe) including connection to drain (out going pipe) "P' or 'S' trap, flush pipe, antisyphonage pipe etc complete all as specified and directed

S&F 15mm bore chromium plated two way tab with flange fancy type,cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions complete all as specified. Make : Jaqual,plumber , parryware

S&F 15mm bore chromium plated health faucet including flexible pipe 1.00 m long wall mounted with brass CP nuts complete all as specified Make ; Jaquar,Parryware , Plumber

S&F PVC valveless syphonic action type flushing cistern 10 litres capacity low level white.with inlet ball valve, float and handle including brackets complete all as specified.

S&F Vitreous china urinal half stall type white coloured with urinal spreader of CP suitable for fixing 15mm dia pipe,( Minimum weight 60 gms) including providing and fixing plugs,bedding urinal against wall in cement mortar 1;2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in white cement, including connection to flush pipe,grating and union for discharge pipe (excluding supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F vitreous china wash hand basin of size 550 x 400mm oval shaped, under counter etc including brackets complete all as specified .

S&F 15mm dia swan neck pillar tap fancy type,cast copper alloy,with capstain heads,chromium plated screwed down high pressure,with or without lettered 'HOT' or 'COLD" with long screwed shanks and fly-nuts screwed for iron pipe compete all as specified.

S&F Brass chromium plated waste fitting 32mm bore complete all as specified.

S&F PVC waste down pipe of suitable size for wash hand basin/Urinals

S&F for PVC connection 15mm size with PTMT nuts of length 450mm

S&F granite tiles (of any type) 20mm thick machine cut,bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified.

S& F in repairs CP fancy type angle cock one way, brass chromium plated, fixed to iron pipe or for unions 15mm bore complete all as specified.

S&F bib taps cast copper alloy chromium plated with crutch or butterfly handle,fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified.

S&F brass chromium plated tubuler towal rail,20mm dia D type 60cm long between flanges.

M&L for rendering 10mm thick in cement mortar 1:3 on concrete surfaces in ceiling finished even and smooth without using extra cement all as specified.

M&L for preperation of new plastered surfaces of ceiling and applying three coat of white wash all as specified.

M&L for applying two coats of tack coat with industrial bitumen 85/25 grade at the rate of 1.20Kg per Sqm each coat including cleaning and preparing surfaces complete all as specified. NOTE : Ist coat for bonding of material belwo membrane and second coat on top of membrance. Two coats of tack coat shall be measured as one unit lenght.

M&L for laying APP based polymeric membrane minimum weighing 3 Kg / Sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/Sqm) laid on priimed surface by forced torch application complete all as specified.

M&L for applying two coats of bitumen based aluminium paint over a coat of primer on APP membrane including preparation of surfaces complete all as specified.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of wall care putty complete all as specified.Note: Wall care putty shall be mesured and paid separately under relevant item.

M&L for applying 1mm thick white cement based wall care putty on wall finished even and smooth for painting complete all as specified.

M&L for preparation of newly plastered surface of wall,pilasters,cornices etc and applying two coats of Anti fungal weather coat acrylic emulsion paint over a coat of primer (X2) complete all as specified Make : (a) Asian (Apex ultima).berger weather coat all gaurd. ICI Dulex (Weather sheild Max), Nerolac (Excel total) Make of primer : Asin (X2) or other equivalant as approved by GE. Note : (a) Each stages i.e Preparation of primer application of first coat and second coat of Apex be passed by Engineer-in-charge (b) Written warrenty for four years shall be funished by the contractor. (c) Work shall be carried out upto G+3 storied building.

M&L for Machine pressed rubber moulded precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M 35 Grade with grey cement and no pigment laid over dry screened stone dust complete all as specified and directed. NOTE : Stone dust shall be measured and paid separately under relevant item.

M&L for stone dust under floors or in foundation including spreading , levelling , watering in layers n.exc 25 cm thick all as specified.Note: Thickness shall be measured after punning .

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggrgate) as in mud stops kerbs etc rounded or chamfered edges complete all as specified.

M&L for construction of septic tank for 100 users including earth work exacavation in any type of soil ,returning filling ,removing soil,foundation with PCC 1:2:4 type B2 ,brick work in CM 1:4 ,RCC 1:2:4 cover Slab including 6mm plate embedded all around to hold cover slab / Fibre reinforced cover with angle iron frame ,Vent shaft and sludge chambers etc. complete all as specified and shown on TD drawing No CEJZ/TD/57 sheet No 1/4 to 4/4 dated 05/05/2000

M&L for concrete bed in PCC 1:4:8 type D2 (using 40mm graded stone aggregate) including packing under & haunching against the sides of pipes after they are laid and tested complete all as specified .

M&L for Reinforced concrete pipes 150 mm bore class NP2 laid and jointed with collar all as specified.

S&F FRC manhole cover including rectangluer frame of size 44''X26'' md-10 fixed at site as per direction of Engineer-in-charge.

M&L for brick work with fly ash brick using modular size brick, striaght or curved on plain exceeding 6m mean radius built in cement mortal 1:4 complete all as specified.

M&L for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in coping,bearing course,manhole /drain channels etc including necesarry form work complete all as specified.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in surface channel including form work complete all as specifed.

M&L for rendering 15mm thick in cment mortal 1:4 on fair fixes of brick work or concrete surface, finished even and smooth without using extra cment all as specified.

S & F in repair Rotational moulded polythylene water storage tanks(double layer) 2000 Litres capacity, (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 25mm bore complete all as specified. Make:- Syntex/Polywell.

All as per item No 84.00 above but for 1000 litres capacity.

S&F in repair of gun metal gate valves 20 mm with lever arm screwed both ends for iron pipes complete all as specified .

S&F in repair of gun metal gate valves 25 mm with lever arm screwed both ends for iron pipes complete all as specified

S & F in repair CP fancy type Stop Valve ( Concealed type),cast copper alloy, screwed both ends for iron pipe or for union of 15mm bore complete all as specified.

Taking up or down steel tubing 15mm bore including connection complete all as specified.

Taking up or down steel tubing 20mm bore including connection complete all as specified.

Taking up or down steel tubing 25mm bore including connection complete all as specified.

S & F in repairs CP Brass fancy type shower rose 15mm dia with 125mm long CP Nipple of approved quality complete all as specified. Make : Plumber/Parryware.

Dismantling floor or wall tile including cement mortar backing and removing rubbish off the premises complete all as specified.

S&F in repair PVC (SWR) pipes 150 mm bore single socketed in any length with rubber ring joints laid on wall / floor including clamps complete all as specified.

Surface dressing n exc 15 cm deep in soft/loose soil including removing soil to a distance n.exc 50m and depositing where directed .

M&L for plain Cement concrete 1:3:6 type C2 using 40mm graded stone aggregated as in filling, sub base, complete all as specified.

M&L for reinforced design mix concrete M25 grade as in chajjas complete all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified.

S&F vitreous china wash hand basins of size 550 x 400mm flatl back or angle back type including cutting for and pinning in ends of brackets complete all as specified.

S&F vitreous china urinal half stall type 350x390x600 mm (minimum) including providing & fixing of plugs, bedding urinal against wall in cement mortar 1:2 ,pointing around urinal back in white cement complete all as specified.

S&F CP brass urinal spreader for fixing with 15 mm dia pipe.

S&F urinal partition with HPL board material 10 to 12mm thick,of size 900x450x350 mm fixed with brackets complete all as specified.

S&F PVC pipe 40 mm dia, in any length and in any position such as walls, ceiling or laid in floor or trenches etc. complete all as specified.

S&F PVC bend suitable for PVC pipe 40 mm dia complete all as specified.

S & F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete.

S&F in repair SS tubular towel rail, 60 cm long, 20mm bore,complete all as specified.

S&F in repair SS Toilet paper holder,complete all as specified.

M&L for preparation of surfaces for applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete.

M&L for on site LLDPE septic tank designed to carry sewage and sluge water for 10 users including excavation in any type of soil,returning filling in soil,removing , PCC 1:4:8 foundation, Vent shaft, connection. etc complete all as specified by Engineer-in-charge

M&L for Soakage wells of size 1.2m dia, 1.5m depth including excavation, in any type of soil, returning filling in soil,removing ,foundation in PCC 1:3:6, walls of honey combed masonry built in CM 1:4 with top ring of M25 grade concrete including intercepting chamber and screen chamber made of brick masonry in 1:4 CM, RCC cover slab in M25 / SFRC cover, interconnecting pipes of RCC/DWC filled with brick bats complete all as specified and directed by Engineer-in-charge.

S&F PVC pipe 40 mm dia, in any length and in any position such as walls, ceiling or laid in floor or trenches etc. complete all as specified.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum getting out in any type of soil including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface etc complete.

S&F Mild steel work in roof trusses (framed), trussed, purlins, rafter,crane ganrties, rails and fastening and heavy bracket framing including distance pieces, cleats etc Fe 410-W-(Gde-E 25) quality A complete

S&F Pre-painted galvalume aluminium zinc GI based profile pattern steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified

S&F mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410-W (gde-E-250) Quality-A)

M&L for preparation of new or previously untreated steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base , floor etc complete all as specified

M&L for rubber moulded cement concrete tile of size 40cm x 40cm x 25mm thick with grey cement and pigment ,set , jointed and pointed in neat cement slurry as in floor over and including 15mm thick screed bed in CM 1:6 complete all as specified

M&L for plain cement concrete 1:2:4 type B2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete.

M&L for preparation of new plastered surface of walls and applying two coats of cement base paint all as specified

M&L for Glazed ceramic coloured tile of size 300mm X200mm X7mm thick on vertical surfaces such as dado,skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile including 10mm thick backing coat in CM 1:4 all as specified .

Supply and laying LT cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core.

Supply, laying and jointing GI pipe 'light grade' 40 mm bore in trenches / under floors or roads / along poles/ on wall including clamps for protection of cables complete all as specified.

M&L for clean and dry sand (un-washed) in trenches including spreading and levelling for cushioning of UG cable complete all specified.

M&L for brick sub class ‘B’ (modular size), laid flat in trenches for protection of cable complete all as specified.

M & L for Point wiring with FR LS PVC insulated PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc for following. Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian .

One light point controlled by one switch

One Exhaust fan point controlled by one switch

One 5Amps socket out let point controlled by one switch on same board with other switches.

One 5Amps socket out let point on independent board controlled by one switch.

All as per item No 128 above but PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

S&F switch piano flush button single pole one way 6 Amp 240 volt complete

S&F socket outlet flush type 5 pin, 6 amps, 230 volts complete.

S&F switch piano flush button single pole one way 15 Amp 240 volt complete.

S&F socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete.

S&F ceiling rose surface bakelite three terminal complete.

Supply and fix integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or equivalent in Wipro

Supply and fix integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed .Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH or equivalent in Wipro

Supply and fix LED street light fittings 1x30 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed .Make:- Havells Cat No.LHEXAYP7PN6K030 Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2

Supply and fix double door SPN DBs 4 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din rail complete all as specified and directed by Engr-in-Charge.

Supply and fix double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din rail complete all as specified.

S & F MCB SPN 6 to 32 Amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified.

M&L for Sub main wiring with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including FR LS PVC insulated unsheathed 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge.

Supply and fixing Exhaust fan 200mm sweep, AC single phase 230 Volts, non metallic type, complete with louver including electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model: Ventil Air-DX white or equivalent in /Bajaj/Crompton

M & L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type c-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion including taking down/dismantling the existing complete all as specified and directed.

Chitragupta Construction

Goyal Construction

Bharadwaj Builders

sunway associates