SPECIAL REPAIR TO CERTAIN REGIMENTAL SHOPS P 152

Amount

Demolition of brick work or stone/boulder masonry built in cement mortar complete all as specified and directed by Engr In Charge.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 M mean radius built in CM 1:6 complete all as specified and directed by Engr In Charge.

Demolition reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas, RCC Jali and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed

Material and labour for false ceilings using GI snap grid system with roll-formed out of hot dip galvanised steel caping (powder coated) main runner 38 x 24 mm , cross Tee 29 x 24 mm and wall angle 24 x 24 mm members suspended with 4mm dia GI wire, carry maximum load up to 8.10 Kg/Sqm with 4mm thick designer ceiling board , pre painted Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions size 595 x 595mmx 4mm thick any texture (Lake and Hill, oceaniccascade or Electra) as approved by GE all as per , Everest Ceiling grid system 'Regular T-2430' or its equivalent make of "'Ramco, Charminar/Armstrong'' at any height complete all as specified and as directed by Engr-In-Charge.

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortal 1:6 on fair faces of brick work or concrete surfaces etc including finished even and smooth without using extra cement including taking down cement plaster complete all as specified and directed by Engr In Charge.

M&L rendering 15mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces finished even and fair without using extra cement complete all as specified and directed by Engr In Charge.

M & L rendering 5mm thick on ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed by Engr In Charge.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) area exc 1.5 sqm and not n.exc 4.0 sqm (including make good with CM 1:4 and hold fast) complete all as specified and directed by Engr In Charge.

All as per Item No 10 here in before but not exc 1.5 Sqm .

S&F for size 105x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, hold fast, lock strike plate, etc., complete as specified,complete all as specified and directed by Engr In Charge.

S&F windows/ventilators section of frame 72 X 55 fixed to wall or concrete surface with ms hold fast (30 x 5 section) 150 mm long made of galvanised steel powder coated and section of shutter 47 X 20 mm mulion section 72 X 50 mm (Base steel as per IS 513 "D" quality galvanised as per IS 277 with zinc of 120 gms/ Sqm ) glazed or guaged and wire guage shutter prepare to recieve wire mess to the shutters ( Double door shutter) with total coated thickness of 0.60 mm including powder coated grill/guard bars made of surface bars 10 mm dia at 100 c/c horizontal spacing fixed in ms flat frame ( 30 x 5 mm ) fixed to windwods frames with screws incl 4 to 5 mm thick sheet glass, 0.36 mm stainless steel wire cloth with 1.40 mm aparture neccessary fittings and all builders hard ware such as handles ,tower bolts, and stays and cooler opening shall be provided with double side shutter with grill and design of window shall be approved by Engr-in-Charge etc. complete all as specified and shown in Drg No : CEAF/STD-191/2014 Sheet No 1/2 and 2/2 dated 11-12-2014 including taking down existing window/ventilator and making good

M & L for cement concrete 1:3:6 (using12.5 mm graded stone aggregate) in door and windows frames, any size, single or double rebated, including ar- rangement for fixing of hinges and fixtures as required complete all as specified and directed by Engr In Charge.

S & F 35mm factory made plain framed, Flush shutters, solid core construction, with block board core and plywood face panels, commercial particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr In Charge.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified and directed by Engr In Charge.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face complete all as specified and directed by Engr In Charge.

S&F 150mm long Aluminium anodised, barrel tower bolts of ex- truded section and fixed complete and specified and directed by engr-in -charge.

S&F 150mm long aluminium handle cast type polished bright complete and specified and directed by engr-in -charge.

S&F 100 mm long butt hinges medium weight, stenless steel, and fixed complete and specified and directed by engr-in -charge.

S&F for 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete and specified and as directed by engr-in -charge.

Dismantling stone slab and granite of any description or thickness in floors etc and removing the debries outside the MOD land complete all as specified and directed by Engineer-in-Charge.

M & L 15 mm thick screed bed or bedding layer of cement mortar (1:4), for laying of granite complete all as specified and directed by Engr In Charge.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in flooring, steps, jambs, pillars, win- dow-cills, cooking plat- forms and like in cement mortar (1:4) including point- ing in white cement (1:2) us- ing marble dust with admix- ture of pigment to match with shade of granite complete all as spd .

Supply only integral water proofing compound as per manufactures instructions complete all as specified and directed by Engr In Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and by Engr In Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr In Charge.

M&L Glazed ceramic coloured tiles in vertical surface 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl back plaster 10 mm thick in cm 1:4 complete all as specified and directed by Engr In Charge.

M&L for scratch free vitrified ceramic tiles 10mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M & L for providing type B-0 1:2:4 cement concrete (using 12.5mm graded stone aggregate) as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete and specified and as directed by engr-in -charge.

M&L for preparation of new plastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of alkali resistant primer specified and as directed by engr-in -charge.

Complete removal of existing treatment on walls and applying two coat of approved shade of oil emulsion distemper over a coat of alkali resistant primer all as specified and directed by Engr-in-Charge.

M&L preparation of new plastered or unplastered surface and applying three coats of white wash on ceiling complete and all as specified and directed by engr-in -charge.

M & L preparation of old plastered surface and applying two coats of white wash on ceiling complete and all as specified and directed by engr-in -charge.

Preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

M&L Preparation of new wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr In Charge.

M&L one coats of synthetic enamel paint including preparation of old wooden surfaces complete all as specified and directed by Engr In Charge.

Material & labour for preparation of new plastered surfaces and applying two coat of exterior grade modified antifungal water based weather proof acrylic emulsion dirt cleaning property paints on wall, fins, facias, chajjas over a coat of primer incl 3mm thick wall care putty etc upto and including 4th storyed high building complete all as specified and as directed by the Engr-in-Charge.

Material & labour for preparation of new plastered surfaces and applying two coat of exterior grade modified antifungal water based weather proof acrylic emulsion dirt cleaning property paints on wall, fins, facias, chajjas over a coat of primer including 4th storyed high building complete all as specified and as directed by the Engr-in-Charge.

Material & labour for preparation of old decorated plastered surfaces and applying two coat of exterior grade modified antifungal water based weather proof acrylic emulsion dirt cleaning property paints on wall, fins, facias, chajjas incl 3mm thick wall care putty etc upto and including 4th storyed high building complete all as specified and as directed by the Engr-in-Charge.

Taking down steel tubing or removing from site of 15mm bore pipe all as specified and directed by Engineer-in-charge.

All as per Item No 41 here in before but 20mm bore.

S&F for 15mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.

All as per Item No 43 here in before but 20mm bore

Dismantling water tanks exc 250 but not exc 500 ltrs capacity and removing to store complete all as specified and directed by Engr In Charge.

S&F Rotational moulded polyethylene 500 Ltr water storage tanks as per IS (cylindrical vertical with closed top) hoisted and fixed in position including necessary fittings complete all as specified and as directed by Engr-in-Charge.

S &F for 20 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass errule and fixed complete all as specified and directed by Engr In Charge.

S&F in repair vitreous china squatting pan “orrisa” pattern of size 580mmx440mm “white” with integral foot rest (excluding flushing cistern and flush pipe) incl provision of cement concrete bedding, ‘P’ trap 100mm dia connection to trap , anti-syphonage complete all as specified and directed by Engineer-in-charge.

S&F in repair for vitreous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding fixing bolts, flushing cistern and flush pipe) complete all as specified.

S&F in repairs10 ltr capacity PVC flushing cistern coloured with accessories Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete and specified and directed by engr-in -charge.

S & F in repairs for 125mm dia Steelness steel grating doom with or without waste hole for waste pipe ( minimum weight 40 gram) complete all as specified and directed by Engr In Charge.

S/F in repairs 15 mm Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated with long shank and cup (concealed type)all as per specified and directed by Engr-in-Charge.

S & F in repairs 15mm CP bib tap fancy type copper alloy with crutch or butterfly handle , screwed down, screwed for iron pipe etc complete all as specified and directed by Engr In Charge.

M&L in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engr In Charge.

S&F in repairs vitreous china wash hand basin of size 550mm x 400mm white, flat back including angle iron brackets with two coats of synthetic enamel paints including PVC waste pipe of 32mm dia of suitable length, CP fancy type pillar cock, PVC connection of 15mm dia & 450mm long with PTMT nuts, and 32mm dia brass waste fitting complete all as specified.

S&F 15mm dia PVC Connection 450 mm long with nuts complete all as specified and directed by Engr In Charge.

S&F in repair for vitreous china urinal half stall type white complete all as specificed and directed by Engr-in-Charge.

M & L for complete removal of existing roof treatment with mud faska including bedding layer in cement mortar complete all as specified and directed by Engr In Charge.

M&L for Providing, cement concrete type B-0 1:2:4 (12.5 mm graded aggregate) in roof kerbs or mud stops, padding, rounded or chamfered on edges without using extra cement complete all as specified and directed by Engr In Charge.

M&L for 10 mm thick cement mortar 1:4 on fair faces of brick or concrete surfaces with integrlal water proofing compound as per manufacturers instructions complete all as directed and specified. Note : WPC shall be paid and measured seperately under relavent item

M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatement complete all as specified and directed by Engineer-in-Charge.:- (a) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface. (b) Laying of 3mm thick prefabricated APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 170 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc. Note:- This treatement shall be done by the approved authorized applicators and guarantee of treatement shall be minimum 10 years complete all as specified and directed by Engr In Charge.

M&L applying two coats of water proofing aluminium paint over APP membrane complete all as directed by Engineer-in-Charge.

Dismantling of aluminium door, partition, window & ventilator including all necessary fittings complete all as specified and as directed

S&F fabricating coloured powder coated aluminium frame work,door shutter ,windows , ventilators, partitions with one or more rebates sections of approved tint as required for partions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified and directed.

S&F aluminium coloured powder coated door shutters, aluminium section weighing min 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, pad lock, hinges, anodised aluminium snap beading screws etc complete all as specified and directed. .

S&F Aluminium( extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as directed and specified.

S&F for double action floor spring hydraulically regulated mode lap of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed to shutter complete all as specified and directed by Engr-in-Charge.

S&F brass body Mortice lock, vertical type,size 100 mm 4 lever, incl escutcheon plate and two No keys fixed complete all as specified and directed by Engr-in-Charge.

S&F 5.5 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium doors/window/partition incl necessary cutting / moulding and chamferring of edges for service window/counters complete all as specified and directed.

Dismantling of corrugated steel sheeting any gauge, thickeness including nainital or similar roof coverings complete all as specified and as directed.

S & F moulded pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified.

S & F moulded pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in eaves sheeting /cladding to wall, fixed with self tapping screws as specified.

S & F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161 1979 grade St-240

M&L Machine pre polished cut kota stone flooring 20 mm(+-2mm) thick in tread of steps, and similar over cement screed 20 mm thick in cm 1;4 base laid and jointed with grey slurry mixed with pigment to match the slab including rubbing and polishing complete all as specified and directed by Engr In Charge.

S&F 5mm thick ACP wall cladding sheet in colour as directed by Engr-in Charge. Fixed on existing MS frame of any size The size of each panel not exc 1.5 sqm. Including all necessary repairing work as reqd. Letters on the existing sign board removing safely and fixing the same on new ACP sheet including denting, painting & polishing.

M&L for glossy finished chequered cement concrete coloured tiles (300mm x 300mm) 25mm thick confirming to IS -1237 (rubber moulded) in floor setc, set, jointed & pointed with cement slurry 15mm thick bedding layer of cement sand mortar (1:6) including dismentling of existing tiles complete all as specified by Engr-in-Charge.

S&F precast machine pressed PCC interlocking paver block of 60 mm thickness, M-35 grade of any shape and size confirming to IS -15658-2006 with grey cement and pigment as approved and 100mm thick plain cement concrete, type D-2, 1:4:8, (using 40mm graded stone aggregate) as in sub base flooring, surface finished even and rough to receive floor topping including sand cusion and including dismentling of existing paver block complete all as specified and directed by Engineer-in-Charge.

M&L Sand filling under floors or in foundation including watering and consolidtion complete all as specified and directed.

Taking down carefully copper/aluminium point wiring light ,fan, light fittings,socket or power complete, such as switches, ceiling roses, pendents, regulators, sockets etc.removing materials to store for keeping in safe costudy or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge.

M&L for light/fan/bell point wiring with single core PVC insulated unsheathed 1100 volt grade cable with multi strand copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through and including non metallic rigid PVC concealed conduit, medium grade, ISI marked not less than 20mm dia, concealed in wall, ceiling with GI saddles GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and provision of pressed steel terminal modular box powder coated of suitable size for mounting modular switch/sockets and regulators and drawing continuous earth wire of PVC insulated unsheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) for light/fans/bell controlled by one well push button complete all as specified and directed. Note: Cost for cutting, chasing and making good to existing surfaces are deemed to be included in the Quoted Rate.

All as per item No-81 here in before but for one 3 pin socket out let, 6 Amps on same board with the cable 1.5 Sqmm size.

All as per item No-81 here in before but for one 3 pin socket out let, 6 Amps on Independent board with the cable 1.5 Sqmm size.

All as per item No 81 here in before but with 2.5 Sq mm cable for Independent bd one 3 pin 15 Amps socket outlet including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR LS cable for continuous earth wire connected to earh terminal as required size all as specified and directed by Engineer-in-Charge.

S & F Modular switch 1 way 6A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Socket, 6A - 2/3 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S&F Modular switch 1 way 16A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Socket, 16A - 2/3 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,3 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,6 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,8 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of ceiling roses, surface bakelite 65x50mm 3 terminals , PVC/Polycarbonate, isolated body fixed on PVC round block complete all as specified and directed by Engineer-In- Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing holders & LED bulb suitable for wall sas specified and directed by the Engineer- In- Charge.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

M & L for in replacement submain wiring with two run of 6.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 6.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified - Note :- 2 Runs of 6.0 Sqmm single core and one run of 6.0 sqmm single core cable for earth continuity conductor with 1 Run of PVC conduit shall be measured as one unit for measurement purpose.

M & L for in replacement submain wiring with two run of 10.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 10.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified - 2 Runs of 10 Sqmm single core and one run of 10 sqmm single core cable for earth continuity conductor with one run of PVC conduit shall be measured as on unit for measurement purpose.

Taking down unserviceable submain wiring of alluminium copper three/two runs of any size cable including batten/conduit complete etc and making good distrub surfaces complete all as specified and directed.

Supply and fixing in replacement load line vertical distribution board 'A' frame made out of CRCA sheet,double door, surface mounting TPN 4 way 415 volts 125 Amps rated bus bar and stove enamels dust and vermin proof suitable forTP/FP 'A' frame MCCB of 40/63 Amps =01 No MCCB for outgoing complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.

Supply and fixing in replacement MCB distribution board with Bus bar 200A neutral link , earth bar made out of CRCA mild steel sheet surface mounting SPN 12 way 230 volts double door type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.

Supply and fixing in replacement MCB distribution board with Bus bar 200A neutral link , earth bar made out of CRCA mild steel sheet surface mounting SPN 8 way 230 volts double door type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.

Supply and fixing in replacement MCB distribution board with Bus bar 200A neutral link , earth bar made out of CRCA mild steel sheet surface mounting SPN 4 way 230 volts double door type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.

Taking down old unsv MCB DB of any size. Complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode 60cmx60cmx6.3mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with top edge of the plate not less than 1.5 meter below normal ground level, connected to and including galvanized iron strip 4 mm dia as earth lead by means of GI bolts, nuts, check nuts and washers earth pit surrounded by picked layer of coal dust and 15 mm thick mixture in equal ratio of magnesium sulphate & copper sulphate in all around bottom and top and watering pipe 20mm bore of GI medium grade with funnel all as shown in electrical plate NO 3 of SSR Part I (2010) and connecting to earthing test point, including CI cover, frame and PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in earthing pit with CI cover and framing including necessary earth work etc, complete all as specified Note :- PCC chamber shall be constructed at least one meter away from building shall be provided in slanting manner.

Supply and fix in replacement of fixed thermal and fixed magnetic settings, 4 pole MCCB 100 Amps, 50 HZ, 415 volts with rupturing capacity 16 KA complete all as specified and directed by Engineer-in-charge.

Taking down unserviceable SP/SPN MCBs of any capacities from the MCCB DBs /MCB DBs after disconnecting the electric supply,complete all as specified.

S&F MCB SP 5 to 32 Amps 10 KA, 240 volt 'C' Series all as specified and directed by engineer-in-charge.

S&F MCB SPN 40 Amps 10 KA, 240 volt 50 HZ 'C' Series all as specified and directed by engineer-in-charge.

shakti construction

M/S MG GROUP

Ashish Sehgal and Co.

Hindustan Co.Co

J D ENTERPRISES

SURESH KUMAR SHARMA & CO

Mahesh Enterprises