REPAIRS TO WATER SUPPLY LINES JOINERIES ROOF SHEETS AND OTHER B R REPAIRS TO CERTAIN BULIDINGS AND REPAIRS CLEANING OF SEWAGE LINES MANHOLES SEPTIC TANK SOAK WELLS ETC IN AT COLLEGFE AREA AT DSSC WELLINGTON

Amount

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises (including removed demolition materials from site within 1 km radius from site) complete all as specified and directed

Demolition of cement concrete (unreinforced ) of any description and in any postion not otherwise spcifically provided etc (below or above ground level)/sunken floors pavings and removing debris off the site complete all as spcified and as directed.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Material and labour for Rendering in Cement Mortar 1:6, 15mm thick on stone masonry or other than fair faces of brick work wall surfaces, finished even and smooth without using extra cement complete all as specified and as directed..

Material and labour for rendering 20mm thick in Cement Mortar 1:4 mixed with liquid water proofing compound as per manufacturers' instructions on stone masonry surfaces of wall, finished even and smooth without using extra cement complete all as specified and as directed. Note: Liquid water proofing compound shall be measured and paid separately.

Material and labour for Rendering in Cement Mortar 1:3, 5mm thick ceiling surface of concrete etc finished even and smooth without using extra cement complete all as specified and as directed..

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of mortar in cement plaster 1:4 all as specified and directed. MAKe : Khajaria/Somany/Rak ceramics

All as per item No 07 above but in skirting/dado over 15 mm thick screed bed or bedding layer of mortar in cement plaster 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 300 x 600 x 6 to 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match placed in 10mm thick CM 1:3 complete all as specified and directed.MAKe : Khajaria/Somany/Rak ceramics

M&L for Light shade coloured Virified Ceramic tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors and scantling etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and directed.Make : Khajaria/Somany/Rak ceramics

M&L for Light shade coloured Virified Ceramic tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors and scantling etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screed bed in CM 1:3 complete all as specified and directed.Make : Khajaria/Somany/Rak ceramics

M&L for 25mm thick PCC type B-0 1:2:4, using 12.5mm graded crushed stone aggregate as in flooring to receive tiles etc complete all as specified and directed

M&L for providing and laying water proofing treatment to sunken floor portion of WC ,Bathroom etc,by applying first layer of slurry of cement @0.488 kg/Sqm mixed with Dr fixit or Equivalent Acrylic based polymer modified cementitious (PMC) composite compound @ 0.253kg/sqm and second layer of slurry of cement 0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @0.126kg /sqm complete all as specified and as directed.

M & L 20mm thick cement screed in cement mortar 1:3 mixed with liquid water proofing compound FOSROC's complast 421 IC @ 130ml per bag of cement including a bonding coat of FOSROC's Nito bond AR cement slurry for roofcslab/ floor complete all as specified (liquid water proofing compound are measure seperately)

M&L PCC 1:4:8 type D2 with 40mm graded stone aggregate as in sunken floor/toilet floor /kitchen floor concrete finished the surfaces fair and even to receive top layer all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid and bedded in any mortar complete .

M&L for Granite of 18-20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl 15mm thick screed bed in CM 1:4 including polishing, rounding /notching of ends and making hole for gas pipe complete all as specified and directed

S & F in repairs 15mm bore medium grade tubes, galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors incl taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore complete all as specified and directed

S & F in repairs 20mm bore medium grade tubes, galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors incl taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed

S&F in repairs 5.50mm thick looking mirror of size 600x450mm on 6mm thick (Teak/PVC beading) (Water proof plywood/AC sheet backing) including framing with 1st class hard wood of size 40x40mm decorative type polished complete all as specified and directed

Supply and Fix in repair, 1000 litres capacity triple layered Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement including making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part -I (2009) complete all as specified and as directed. Make: Sintex/Polycon/Vectus

Supply and Fix in repair, 500 litres capacity Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, three layered (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement including making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part -I (2009) etc., complete all as specified and as directed.

S&F 25mm bore, Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed,weight 455 gms complete as specified and as directed.

S&F 25mm bore, Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and as directed.

S&F 20mm bore, Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and as directed.

Disconnecting existing tanks, of setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position tank storage capacity Exc 250 but n.exc 500 Ltr capacity complete.

Disconnecting existing tanks, of setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position tank storage capacity Exc 500 but n.exc1000Ltr capacity complete.

Supply and fix in repair PVC tank cover for PVC water storage tank of capacioty exc 250 ltr but not exc 500 Ltr including necessary fittings complete .

Supply and fix in repair PVC tank cover for PVC water storage tank of capacioty exc 500 ltr but not exc 1000 Ltr including necessary fittings complete .

S&F in repairs 15mm dia bib tap long body with flange complete all as specified. Make : CERA ,Cat part No : F2002152 or ESSCO Cat part No : ORB-105107 complete all as specified and directed

S&F in repairs 15mm dia angle cock with flange complete all as specified. Make : CERA ,Cat part No : F2002201 or ESSCO cat part No :ORB-105053 complete all as specified and directed

S&F in repairs 15mm dia centre hole basin Quarter turn mixer w/o pop up waste system complete all as specified Make : Cat part No : Jaquar cop-167BPM or CERA F1003461 of Equivalent.

S&F in repairs 15mm dia wall mixer with L bend (Provision for OH shower) complete all as specified Make : Prayag Cat No 7275 or equivalent in Parryware/Hindware)

S&F in repairs 15mm dia wall mixer 3 in 1 (Provision for OH shower & Hand shower) complete all as specified Make : CERA cat part No:F1018401 or Essco cat part No: 105281

Supply and fix in repairs two way Bib cock 15 mm bore, cast copper alloy, chromium plated, fancy type with flange and crutch or butterfly handle conforming to IS as per Cat No.CON-041 of Jaquar or T3534A1 of Parryware screwed down high pressure with fly nuts, screwed for iron pipes or for brass ferrule etc., complete all as specified and as directed.

S&F in repair health faucet Make:Cat No. E8342A1of Parryware /F160001 of Hindware/ ALD-CHR 565 of Jaquar including 1.2m long flexible tube and wall hook complete all as specified and as directed.

S&F in repairs 15mm dia 4" overhead shower with 225mm arm & flange complete all as specified Make : CERA cat part No: F7010102 or

S&F in repairs corner glass shelf 300mm (with ABS brackets) complete all as specified Make : Prayag Cat No BEA-46 or equivalent in Parryware/Hindware)

S&F in repairs PVC connection with brass nut 600mm long complete all as specified Make :Parryware/Hindware)

S&F in repairs Towel rail complete all as specified Make : Prayag Cat No BA-01 or equivalent in Parryware/Hindware)

S&F in repair soap dish holder of Make: Cat No T6902A1 of Parryware/ F580004 of Hindware/ ACN 1131N of Jaguar or equivalent all as specified and directed .

S&F in repair toilet paper holder Make: Cat No T6906A1 of Parryware/ F890003 of Hindware/ CAN-1151N of Jaquar fixed to walls with chromium plated (CP) brass screws all as specified and directed .

Supply and fix in repairs stainless steel tubular towel rack 600mm long without lower hangers but with three hooks, Chromium plated as per Cat No.ACN-1181FHS of Jaquar or T6008A1 of Parryware fixed on walls complete all as specified and as directed .

S&F in repairs corrugated waste pipe 31/32 x 800mm complete all as specified Make : Prayag Cat No 327 or equivalent in Parryware/Hindware)

Supply and fix in repairs, stainless steel plate racks made of stanless steel 0.80mm thick sheet standard size 24'x36x10" and design as approved by GE, complete all as specified and as directed. Make: Nirali/Parryware .

S&F sinks made of stainless steel lmm thick kitchen or laboratory with sink coupling, plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm Make : Nirali/Parrywara/Bule star

S & F in repairs, stainless steel 1 mm thick kitchen sink & draining board over all size 915mm x 460mm with bowl size of 410mm x 330mm x160mm high grade stainless steel 304 (18/8) 18% chrome & 18% Nickel Rust proof with plug washer and waste coupling & waste pipe, including bedding in cement mortar to dwarf wall or on brackets and connecting union pipe, fixed on including taking down vitreous china sink complete all as specified and as directed.Make--Nirali/Prayag/Blue star

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as directed

M&L 0.63mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.Make : TATA/ JSW

M&L 0.80 mm Galvanised, plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified. Make : TATA/JSW.

S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet crumped where ever required 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings fixed with self tapping screws complete all as specified and as directed.Make :JSW

S & F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet crumped where ever required 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings fixed with self tapping screws complete all as specified and as directed.Make: Tata/JSW

M & L for mild steel work as in tubular roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat, square tube etc sections) including distance pieces, cleats etc. Fe 410-W (Gde-E- 250) quality- A complete all as specified and as directed.

Dismantling of single layer mangalore pattern roofing tiles all as directed.

M&L for roof tile, Mangalore pattern, interlocking at side joints, laid dry all as specified

M&L for preparation of new mangalore pattern tile surfaces and appying two coats of tile guard over one coat of primer all as specified.

M/L preparing new surface of steel and appling two coats of synthetic enamel paint over a coat of primer red oxide

Taking down chowkhats or frame n.exc 1.5 Sqm each without taking off shutters from frame, and making good surface as directed by Engr-in-chrage

Taking down chowkhats or frame exc 1.5 Sqm but n exc 4 Sqm each without taking off shutters from frame complete all as specified and directed

Taking down shutter of any description n.exc 1 sqm each complete all as specified and directed

Taking down shutter of any description exc 1 sqm but n. exc 2 sqm each complete all as specified and directed

Resecuring or easing and adjusting without taking down shutters of any description n exc 1 sqm complete all as specified and directed

Resecuring or easing and adjusting without taking down shutters of any description exc 1 sqm but n exc 2 sqm complete all as specified and directed

Taking down and refixing in same opening after resecuring or easing and adjusting shutters of any description n exc 1 sq m complete all as specified and directed

Taking down and refixing in same opening after resecuring or easing and adjusting shutters of any description exc 1 sqm but n exc 2 sqm complete all as specified and directed

S&F for 2nd class hard wood plain solid ,straight chowkhats and frames wrought, framed, rebated on the solid rounded or chamfered put together with glue pinned at joints. complete all as specified and directed

S&F 35 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Glazed and skeleton shutter 35mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc, sizes of me-mbers of shutters as specified in SSR Part I, Section8, clause 8.24 (a) supplied and fitted to chowkats. complete all as specified and directed

S&F for 2nd class hard wood made plain framed panalled door shutter 35 mm thick (any number of panel) with veneered particle board medium density, wood particl board with commercial face venners. complete all as specified and directed

S&F for 2nd class HW glazed and skeleton, shutters,divided into squares to receive glass, gauge etc(with sash bar) with plain chamfered or rounded,mitredand rebated sash bars,any numbers the size of member of shutter as specified in SSR Pt-I clause 8.24 (b) window & ventilaters shutters thickness 30 mm and fitted to chowkat. complete all as specified and directed

S& F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing Make : Syntex/Rajshri plastiwood Pvt Ltd

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Taking down old PVC solid /Prelaminated partition from the floor/wall portion and refix the same after tiling etc incl necessary drilling,bolting and making good the surface complete all as directed by the Engr In charge.

M&L for Providing Gypsum board False ceiling using 12mm thick Gypsum board panels of size as approved by GE, fixed with staples on powder coated standard galvanized iron snap grid frame work of size suitable to fixing Gypsum board using 'T' and angle sections made out of 0.5mm thick PGI sheet, grade of zinc coating 220, bent to shape required as in main member, secondary member, perimeter angle section including provn of G I channel suspender fixed to roof members at the rate of 1200mm c/c and interspaced at 610mm c/c, the main fixing channel shall be fixed through fasteners clips as per manufacturer's instructions with and including plaster of Paris decorative type cornice all around at the junction of wall and ceiling including taking down and refixing of electrical fittings etc., complete all as specified and as directed. Note: The unit rate quoted shall be deemed to include the cost of taking down and refixing of the electrical fittings such as ceiling fan, light fittings etc., and keep in safe custody of same till refixing. The unit rate includes taking down of existing false ceiling completely.(ii) The unit rate includes taking down of existing false ceiling of any description completely. Make : Armstrong/Aerolite/gyproc

M&L for Preparing of gypsum board false ceiling with primer and applying 3 mm thick wall care putty and applying two coat of OBD over one coat of primer complete all as manufacturer instructions and as directed

S&F 9/10mm thick PVC ceiling/wall panels of interlocking types, width 250/255 mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner trim, coner cove,F/J edge trims where required fixedwith hidden screws to steel/wooden frame work complete all as specified and as directed.

Supply and fix UPVC Partition consisting of 7mm thick coloured solid UPVC ply sheet reinforced with frame work made from 60mm x 60mm Casement frame including necessary drilling,jointing and fill the gap with necessary solvent,and fixing all required cleats,brackets ,channels etc all as specifed and directed by the Engr In charge.

Supply and fix Supply and fixing factory made uPVC coloured (approved by GE) side hung/sliding pattern with frame of size 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 8.00 sqm upto 10.00 sqm) comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.l fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.all as specified and directed

UPVC windows : Factory made UPVC colour sliding Windows with glazing all as per manufacturer's direction and following specifications :- (i) UPVC Window frame shall be made of PVC material confirming to IS 10151, the Window frame shall be made of extruded UPVC section having overall dimension of 112 x 52 having wall thickness 2.5 mm ± 0.2 mm . (ii) Corners of wall frame shall be shall be joined by MS galvanized brackets. Joints shall be mitred and plastic welded. (iii) The hinge side of vertical outer frame shall be reinforced with galvanized MS tube of wall thickness 1 mm ± 0.1 mm and the tie rod shall be provided at the bottom of the frame. (iv) The profiles should be two or three chamber system which shall provide high insulation properties. (v) Glazing shall be provided with 5mm thick Plain / frosted glass fixed with appropriate size beading as per manufacurer's specifications. (vi) Stainless steel wire mesh 0.36mm nominal dia and average width of aperature 1.40mm shall be provided with each window shutter. Make : Madhu Industries / AMD overseas Ltd/ Gadli Industries/ Simta Astrix. . Note: The unit rate quoted by contractor includes cost of glass/wire netting and all other connected accessories. Net opening will be measured for payment purpose.(II) The unit rate quoted by contractor includes cost of glass/wire netting and all other connected accessories. Net opening will be measured for payment purpose.

S&F Sheet glass,ordinary qualityand glazing 5.5mm thick with oil putty in square n exc 0.5 sq. m in each pane fixed on UPVc/Almn frame complete including all fitinngs.

Preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of pink primer.

S&F for galvanised mild steel wire cloth of 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with Tinned Tacks or wire staple as directed by Engineer in Charge.

Descruption all as per per item No 82 above, but fixed in repairs (wooden frames/steel frames)

M&L 3 mm thick Figured glass, pin head, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

S&F MS Butt hinges medium weight cold rolled & fixed 100 mm long

S&F MS Butt hinges medium weight cold rolled & fixed 75 mm long

S&F 150mm extruded aluminium alloy handles, fabricated type, anodised

S&F 200mm aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 150mm aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Dismantling boarding any description fixed in any position with nails.

M&L for prelaminated particle board exterior grade 18/19 mm thick prelaminated one side with decorative choice lamination one side and balancing white lamination on other side fixed with screw with timber frame including teak wood lipping 6mm thick all around complete all as specified and directed

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flange 40 mm .

S&F magnetic catcher for cubboards all as specified and directed by Engr in Charge

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

S&F fancy type decorative drapray rod 20 mm dia incl side caps and brackets, as in repairs complete all as specified.

Hasp and staple (Safety type) aluminium anodised including bolt to hinge plate and fixed with screws, 100mm size, complete all as specified and directed by Engr-in-charge.

S&F 300 mm, MS ordinary rat tail rod pattern springs including roller and roller plate complete

S&F MS work as in hold fast etc conforming (Fe-290 Gde-165) complete all as specified and directed

M&L for PCC type B-0 (1:2:4) as in filling of steel chowkats or frames complete all as specified and as directed by Engr-in-charge.

S&F in repair stainless steel door stopper 75mm to 125mm size with rubber as approved by Engr-in-charge

Dismantling of PVC or reinforced cement concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as spd and directed

S&F PVC ( SWR) pipes single socketed in any length with rubber ring joints, fixed to walls or floor 75 mm mm dia

S&F PVC ( SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors 110 mm mm dia

S&F PVC ( SWR) pipes single socketed in any length with rubber ring joints,fixed to walls 110 mm mm dia

S&F PVC (SWR) bends any radius 110 mm bore.

S&F PVC (SWR) bends any radius 75 mm bore.

S&F in repairs stainless steel grating 100mm dia fixed in white cement complete all as specified and directed

S&F in repairs stainless steel grating 100mm dia with hole fixed in white cement complete all as specified and directed

S&F PVC (SWR) floor trap plain with grating incl. jointing with solvent cement (100 mm bore)

S & F in repairs, using HDHMR Board Board 18mm thick both side laminated any colour, as in PVC Bedding Shutter vertical support and horizontal shelfs including necessary fittings of screws/MS Brackets in kitchen cupboard complete all as spd and directed. Make :- EBCO/Green ply/Kitchen

S & F in repairs soft close stainless steel hinges 75mm complete all as specified and as directed . Make : EBCO/GODREJ/KAFF

S & F in repairs Gunmetal handle 150mm complete all as spd and as directed. Make : EBCO/GODREJ/Hettich

S & F stainless steel telescoping channel for drawer including necessary fiiting upto length upto 600mm complete all as spd and directed. Make : EBCO/GODEJ/Hettich

Supply only integral water proofing compound all as specified.

S&F in repairs white vitreous china squatting pan orissa pattern of size 580mm x 440 mm, with integral foot rest and P or S trap connection to trap and to flushing pipe front or back inlet including, trap and taking out old WC & connections incl 110mm PVC (SWR) WC connector with lip ring etc complete (Excl flush tank) Make : CERA/Parryware/Handware

S&F as in repairs Viterous china wash down water closet pan (pedestal pattern) and 'P' or 'S' trap including fixing bolts, PVC bend, seat cover and connecting to PVC (SWR) pipe, complete all as specified (Excl flush tank): . Make : Cat No C-8854 P(180) of Parryware/ Cat No SLS WHT-67515 & SLS WHT-6201 of Jaquar,

S&F in repairs wash hand basin oval counter top type of size 520 x 450mm fixed in existing granite of any size complete all as specified and directed. Make : CERA/Parryware/Hindware.

S&F as in repairs PVC valveless, symphonic action type low level flushing cistern white with inlet, ball valve, float and handle etc complete capacity 10 litres including brackets and upto 1mtr long PVC pipe of 40mm dia and bend complete all as specified and directed. Make : CERA/Parryware/Hindware.

S & F in repairs seat cover for pedestal pan white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed

S & F in repairs vitrious china wash basin, white, flat back, size 580 x 450mm (excluding taps, waste , chain and plug and procelain stopper) but including brackets, cutting for and pinning in ends of brackets or erecting stand all as specified and directed. Make : CERA/Parryware/Hindware.

S& F Pillar cock cromium plated with wall flange complete .screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete all as specified and directed.Make : CERA ,Cat part No : QTF2006101 or Jaquar cat part No-35001PM or equivalent.

S & F in repairs low density polyethelene pipes (LDPE) of pressure Rating 2 Kgs/Sqcm fixed complete to walls 50mm bore with clamps incl bend and socket all as specified and directed

Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc complete, all as specified.

M&L for Providing precast cement concrete solid building blocks masonry with 10cm thick (with plain or interlocking joints as directed) type B-1 (using 20mm graded stone aggregate) setting in mortar, complete, in walls set in cement mortar (1:4) complete all as directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished the surfaces even and smooth without using extra cement.

Welding, Easing, providing hinges and adjusting without taking down steel shutters of any description

Repair to existing rolling shutters, without ball bearing, spring as specified including top cover, anchoring rod, hasp and staple; erected in position as indicated, complete; push pull or manual type and rewelding, rops, stoppers, oiling, greasing, easying etc including necessary replacement of profile, if required grid channel complete all as specified and as directed.

Dismantling alluminium doors including glass pane/prelam particle board.

S&F anodised aluminium powder coated frame for doors, windows ventilators with one or more rebates necessary joining cleats, glazing clips, rubber neoprene packing for fixing etc. complete all as specified.

S&F aluminium powder coated door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified

S&F aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F 5 mm thick Sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane

S&F 9 mm thick prelaminatd particle board, ixterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium/timber frame work

Cleaning Man Holes of depth upto 600 mm, any size, removing the clogged mud, musk etc and throwing the waste/ mud outside MoD land to a distance not less than 50 mtrs all as directed by Engr-in-Charge. Note : (1) Cleaning of manhole shall be carried out by mechanically and the rate quoted shall deemed to be included this aspect (2) Contractor will deploy his superviser to collect the compliants from AGE B/R-III complaints cell in morning 0900 o'clock and after completed in evening submit to compliants cell. No complaints will remains pending more than 06 hrs (Except major complaints) else necessary recovery will be made against contractor as per CA provisions.

Labour only for cleaning Man Holes of depth exc 0.60 mtr but n.exc 1.50 mtr in deep, any size, removing the clogged mud, musk etc and throwing the waste/ mud outside MoD land to a distance not less than 50 mtrs all as directed by Engr-in-Charge. Note : (1) Cleaning of manhole shall be carried out by manually / mechanically and the rate quoted shall deemed to be included this aspect (2) Contractor will deploy his superviser to collect the compliants from AGE B/R-III complaints cell in morning 0900 o'clock and after completed in evening submit to compliants cell. No complaints will remains pending more than 06 hrs (Except major complaints) else necessary recovery will be made against contractor as per CA clause.

Labour only for cleaning Man Holes of depth exc 1.50 mtr but n.exc 3.0 mtr in deep, any size, removing the clogged mud, musk etc and throwing the waste/ mud outside MoD land to a distance not less than 50 mtrs all as directed by Engr-in-Charge. Note : (1) Cleaning of manhole shall be carried out by manually / mechanically and the rate quoted shall deemed to be included this aspect (2) Contractor will deploy his superviser to collect the compliants from AGE B/R-III complaints cell in morning 0900 o'clock and after completed in evening submit to compliants cell. No complaints will remains pending more than 06 hrs (Except major complaints) else necessary recovery will be made against contractor as per CA clause.

Labour only for cleaning of blocked sewage line /soil pipe upto 150mm bore by means of rodding with steel rods / bamboos / wire etc, in order to make the line functional and including bailing out water /sewage by mechanical pump and removing the deposited /residue sludge /debris to outside MoD land as directed by Engr-in-Charge. Note : (1) Cleaning of manhole shall be carried out by manually / mechanically and the rate quoted shall deemed to be included this aspect (2) Contractor will deploy his superviser to collect the compliants from AGE B/R-III complaints cell in morning 0900 o'clock and after completed in evening submit to compliants cell. No complaints will remains pending more than 06 hrs (Except major complaints) else necessary recovery will be made against contractor as per CA clause.

M & L for cleaning the cogged mud , muk etc from septic tank including desludging of existing septic tank including removing the mud /muk etc to a distance exceeding 500 mtrs and removing the deposited /residue sludge /debris to outside MoD land of any capacity and burried in earth all as directed by Engr-in-Charge.

M & L for precast cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) block masonry with solid blocks, exc 10 cm in width and set in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M & L for providing PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundations, fillings and mass concrete all as specified and directed by Eng-in Charge.

M & L for 15 mm thick rendering in CM (1:4) mixed with water proofing compound on brick /concrete surfaces, finished even and smooth with using extra cement complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for such as RCC post, manholes, landings etc (reinforcement cut as required to facilitate demolition) and removing debris off the premises all as specified and directed by Engr-in-Charge

Material and labour for Precast RCC cover slab cement concrete, 1:2:4, type B1, using 20mm graded stone aggregate as in slabs with plain faces including setting in CM 1:4 .

S & F Mild steel TMT bars 6 to 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed by Engr-in-Charge.

All as per item No 148 above but 10mm and over complete all as specified and directed by the Engr-in-Charge.

Excavation in trenches, n. exc 1.5m wide and n.exc 1.5 m in depth; for foundation etc; or for shafts, wells, cesspits, manholes, pier holes etc n. exc 10 Sqm on plan and n. exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and as directed.

Returning filling including spreading leveling watering and well ramming in layers not exc 25 cm hard and dense soil

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed

M & L for PCC (1:3:6) type C-2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore all as specified and directed by Engr-in-Charge.

M & L for PCC (1:3:6) type C-2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 100 mm bore all as specified and directed by Engr-in-Charge.

Material & labour for cutting into existing manholes for connecting new drains (internal dia pipe 150mm), making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-I smooth finished, and reforming benching all as directed by the Engr-in-Charge.

Cleaning of blocked gully trap/floor trap etc of any size by rodding thoroughyly to manhole and well flushing with water after cleaning and including remove of sludge and other materials obtained from cleaning, garbage to a pit made for this purpose and filling upto the earth complete as as specified and as directed.

Supply and fixing in repair white vitreous china wash down water closet pan (pedestal pattern) EWC, of size 520 x 360 x 390 mm with ‘P’ or `S' trap, including fixing bolts, Plastic water closet seat and cover, closed pattern with flat bottom, and mild steel chromium plated or aluminium anodised hinging device, making all necessary connections and making good the disturbed surfaces of floor complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S & F in repairs PVC pipe 160mm dia (CL-2) 0.4 Mpa (4 Kg/Sqcm) fixed with suitable MS brackets on walls or in floors all as specified and as directed

S&F PVC (SWR) bends any radius 160 mm bore all as specified and directed

S&F PVC (SWR) bends any radius 110mm bore with access door all as specified and directed

S&F PVC (SWR) bends any radius 75mm bore with access door all as specified and directed

Labour for fixing only for 110 mm dia PVC (SWR) pipes, type 'B', single socketted, in any length, fixed to walls with suitable MS clamps all as specified and as directed.

Labour for fixing only for 75 mm dia PVC (SWR) pipes, type 'B', single socketted, in any length, fixed to walls with suitable MS clamps all as specified and as directed.

M& L for for PCC type C-2(1:3:6) using 40mm graded stone aggregate as in surface channels and drains including necessary form work complete all as diercted by the Engr In charge.

M & L for PCC (1:2:4), type B-1, (using 20mm graded stone aggregate) as in coping /benching, cills, bands, kerbs etc including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M & L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) 75 mm thick, as in plinth protection /pavings finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M & L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) 75 mm thick, as in sub base without using extra cement complete all as specified and as directed.

M & L for PCC (1:2:4) type B-2 (using 40mm graded stone aggregate) 100 mm thick, as Foot Path finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

S & F Chequered cement concrete colour tiles 30 cm by 30 cm by 25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors , over 20 mm thick screed bed in CM 1 :4 all as specified and directed

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade ' B'

M & L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested for pipes of 300 mm bore.

M&L for Reinforced concrete pipes,300mm bore, class NP2, laid in trenches and jointed as specifiedcomplete with collars all as specified and directed

Sree Constructions