SPECIAL REPAIR TO ROOF IN BUILDING NO ET 13, ETA 73 AND ET 45 AND CERTAIN MINOR WORKS OF ASC CENTRE AND COLLEGE UNDER AGE B/R I IN GE (CENTRAL) BANGALORE

Amount

B/R PORTION : - Dismantling of Asbestos Cement Corrugated or Semi-corrugated sheeting, any gauge, thickness, in roof covering including ridges complete as directed. (measured flat overall)

Dismantling timber scantlings 40 Sq.cm and over in section (unframed work), in any position complete all as specified and directed.

Dismantling timber boarding, any description, fixed in any position with nails complete all as specified and directed.

Dismantling of timber batten for roof tiles, sheets etc of any size including tilting fillets in section in any position fixed with nails spaced exc 15 cm

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of reinforced cement concrete any description and in any position not otherwise specifically provided for etc, cutting reinforcement steel to facilitate demolition of concrete including removing the materials out side MD land complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD landcomplete all as specified and directed

S & F 20 mm thick, second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with screws/nails in any situation as in eaves board, etc complete all as specified and directed.

Fixing only second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with by using new screws/nails in any situation as in eaves board, etc complete all as specified and directed. Note : - Old serviceable timber boarding retrived under item No 03 shall be used.

S & F second class hard wood scantling, clean sawn timber fixed with nails etc complete all as specified and directed.

S & F second class hard wood, clean sawn timber batten sectional area exc 5 sq.cm but not exc 15 sq.cm at 30 cm centre to centre fixed with nails etc complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating (AZ 150) GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating (AZ 150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base of floor, foot path etc complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as surface channels and drains complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, manhole etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

Providing cement concrete type B-1, 1:2:4 mix (using 20 graded stone aggregate) as in roof kerb, filling gap between roof sheet and wall and the like including necessary formwork.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer including minimum 2mm thick wall care putty complete all as specified and directed.

M&L complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of primer to plastered and other surfaces including providing wall care putty two coats in minimum 2 mm thick on plastered surface complete all as specified.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of creosote oil complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of 100% premium acrylic emulsion paint having VOC not less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of approved tint/shade (Company depot tinted) with silicon additive @ 1.43 litre/ 10 Sqm over and including applying priming coat of exterior primer @ 0.90 litre/10 Sqm over new/old surfaces of wall complete all as specified.

M&L preparation of plastered surfaces of wall and applying two coats of 100% premium acrylic emulsion paint having VOC not less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of approved tint/shade (Company depot tinted) with silicon additive @ 1.43 litre/ 10 Sqm over and including priming coat exterior primer applied @ 0.90 litre/10 Sqm over new surfaces of wall complete all as specified.

M & L for surface excavation averaging 15cm deep and n.exc 30cm deep and getting out as in soft/loose soil including removing the soil to a distance exc 250M but not exc 500 M and depositing where directed complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil each n. exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface as directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance exc. 1.50 KM but not exc 5 KM and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for ATT by treating the top surface of filled earth at the rate of 5.00 litres of emulsion per square metre of surface area.

M & L for ATT by treating the soil under plinth protection at the rate of 5.00 litres of emulsion per square metre of surface area.

M & L for ATT by treating the soil along wuth external perimeter of building at the rate of 2.50 litres of emulsion per metre of the perimeter wall. Make name ATT chemical for item No 31 to 33 :- DURSBAN/LETHAL/TRISUL

M & L for precast machine pressed interlocking paver block any shaped and size conforming to IS- 15658-2006, 60mm thick, M-35 grade concrete with grey cement and no pigment, set and jointed in dry sand including providing 75mm thick dry sand filling below paver blocks complete all as directed

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Cutting into existing manholes for inserting new drain pipe, 150mm bore and making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B1 finished to match with existing complete all as directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for extra for forming fair finished to concrete surface of drain 30cm inner girth in cement including forms, mould, mitred/stopped etc complete all as specified and as directed.

Supply and fixing RCC pipe, 150mm bore, class NP-3, laid and jointed with collar complete all as directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggragate) as in bed to drain pipes and forming cradles against the sides of pipes after they are laid and tested complete for 150 mm bore RCC/PVC/DWC drain pipes complete all as specified and directed.

M & L reinforced cement concrete M-25 nominal mix as in foundation, incl rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs under reamed piles and mass concrete.

M & L for Reinforced Cement Concrete M-25 nominal mix as in columns, pillars, piers, post and struts etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in beams, cantilevers, lintel beam etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in slabs supported on walls, beams and column in floors, roofs, landings, balconies and in shelves and the like complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in chajjas etc complete all as specified and directed.

M & L for use & waste Form work to sides of concrete foundations, footings, raft beams, sides and soffits of plinth beams and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides of concrete columns, pillars, piers, post and struts and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings, balconies and in shelves and the like for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to soffits and sides of beams, lintel beam for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides and soffits of concrete chajjas and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides/edges of concrete flats, floor and roofs, in walls, horizontal or slopeing and the similar work, 10cm to 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

S & F TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for moorum/sand/red bajri filling under floors or in foundations laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 150mm/100mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub-base of floor, etc complete all as specified and directed.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, level course etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M&L for 40mm thick Cement concrete type B0 1:2:4 (using 12.5mm graded stone aggregate) mixed with integral water proofing compound by weight of cement as per manufacturer's instructions, as in damp proof course to horizontal or vertical surfaces including necessary formwork complete. (Note : WPC shall be measured and paid separately against respective item as supply only).

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 100 mm size, butt hinges, stainless steel with cadmium coated screws complete all as specified and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F box type steel windows/ventilators double side shutters ie glass and wire mesh shutter, including pressed steel frames made out of CRCA sheet of 80X60X1.25mm thick double rebated, shutters box type made out of CRCA sheet of 40X20X1.0mm thick, 12mm square guard bar/grill welded to steel frame, window shutters side hung, ventilator shutters top hung, box type hinges, aluminium die cast handles for glass shutters, iron flat type handles for mesh shutters, telescopic stays etc complete all as specified in TD drawing No TD/539 dated 09.02.2004 of Chief Engineer Chennai Zone and as directed. NOTE:- (i) Qouted rate under this item shall deemed to be inclusive of steel frame, both side steel shutters, guard bars/grills, handles, stays, beading/fillets for fixing glass/wire mesh including cost elements for fixing of glass & wire mesh and mearurement/ pament shall be considered as one unit by comprising all these elements. (ii) Glass and wire mesh shall be measured and paid as supply only underseparately under respective item.

S & F powder coated aluminium (Minimum thickness of powder coating 50 micron) frame work and shutters for doors, windows, ventilators, including frame for partitions with extruded built up standard tubular section/appropriate Z section and other sections of approved make conforming to IS-733 and IS 1285 fixing with dash fasteners of required dia and size including necessary filling gaps at junction ie at top, bottom and sides with required EPDM rubber/neoprene gasket etc including providing and fixing hinges/ pivots. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat, angle, aluminium snap beading for glazing/ paneling, CP brass/ Stainless steel screws, rollers, handles, locking arrangement etc. complete all as specified. Note : (i) Glass panes and particle board will be measured and paid seperately. (ii) The quoted rate shall be inclusive of cost of rubber beading however it will not be weighed and not paid seperately. (iii) All other minor details including cost of locking arrangement shall deemed to be included in the quoted rate.

S & F 10 mm thick, toughened glass as in hinged doors, partition automatic doors and the similar works including cutting in shape, grinding and drilling holes as required in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 12mm thick prelaminated particle board interior grade with one side decorative choice lamination and other side balancing white lamination fixed to aluminium frame work complete all as directed.

S & F 4 mm thick, sheet glass, ordinary quality glass and glazing with aluminium beading in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 5.5 mm thick, sheet glass, ordinary quality glass and glazing with aluminium beading in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 4 mm thick, sheet glass, figured/ pin headed glass and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F Rolled mild steel work as inpost, trusses, purlins, rafter etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

M & L for granite stone slab, table rubbed and polished (of any type) 18 to 20mm thick, machine cut, as in steps, jambs, pillars, cooking platform and the like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortar 1:4 & cutting, polishing complete all as specified and directed.

M & L for roundings to edges of stone slabs, one edge, such as in steps, cooking platform and other similar situation complete all as directed.

M & L for Vitrified ceramic, nominaled, coloured tiles, Grade B I(b), 10 mm thick, (square/rectangular) polished, area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors, etc including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, joint free of matt finish, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, jint free of matt finish, coloured tiles 8 to 10mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles, 300x600 X7 to 8mm thick as in skirting/dado/steps including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L Rendering 15mm thick on fair faces of brick masonry or concrete surfaces in CM 1:4 surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm in CM 1:6 + 5mm thick in CM 1:4) on fair faces of brick work or concrete surfaces, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceilings (sunshed, chajja, fins etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for roof treatment by rendering 10mm thick in CM 1:4 mixed with water proofing compound by weight of cement as per manufacturer's instruction, applying oil bound bitumen primer @ 1.5 Kg/Sqm and providing 3 mm thick APP membrane weighing not less than 3.6 kg/sqm reinforced with non woven polyester matt weighing not less than 180 gm /sqm having softening point not less than 140 centigrade, having tensile strength of 650N/sqm and 350 N/sqm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap, applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.2 Kg /Sqm on top of membrane surface and then finished with solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm complete all as specified and as directed. NOTE: - Water proofing compound shall be measured and paid separately under respective item.

S&F Vitreous China Wash hand basin , one piece white size 460mmx310mmx220mm including a pair of rag bolts assy, mounted/embeded in counter, providing Pillar Tap 15 mm bore Chromium plated fancy type long neck cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & 32 mm dia LDPE PVC waste pipe, PVC connection 15 mm size 450 mm long complete all as specified & directed by Engineer-in-charge. Make of WHB PRAYAG Cat No 4793 or equivalent of CERA/Hindware/Parryware

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

Supplying and laying of 16mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F rotational moulded polyethylene water storage tanks 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 20 mm water tank nipple, union suitable for HDPE water tank, 20mm bore gun metal gate/globe valve with iron wheel head complete all as specified and directed.

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern),P or S trap type, white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with white PVC seat and cover and 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make PRAYAG Cat No 4125 or equivalent of CERA/Hindware/Parryware

S&F Vitreous China Urinal, Half stall type, (approximate size 375x390x590mm), white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar; fixing flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to urinal/flushing cistern, trap and waste pipe). Make : Prayag Cat No 4998 or equivelent of Parryware/Hindware/CERA Cat No S4020112

S & F Vitreous China (white) urinal partition of approximate size 90X320X720 mm. Make CERA Cat No S4090101 or equivelant of make Parryware/Prayag/Hindware as approved by GE.

S&F 2 way 15 mm bore bib taps with double handle quarter turn fancy type with flange cast copper alloy chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO F1018163 or equvelent of Make Hindware/Parryware/PRAYAG

S&F pillar taps, 15 mm, brass with capstan heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed in repair, complete all as specified and directed. Make: PRAYAG Cat No 8902/F1016101 of CERA or equivelent of PARRYWARE/HINDWARE as approved by GE.

S&F 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001201 or equvelent of Make Hindware/Parryware/PRAYAG

S & F 20 mm flush cock, cast copper alloy, chromium plated, screwed for iron pipe for urinal complete all as specified and directed. Make : PRAYAG Cat No BEA 34 or equivalent of Hindware/Parryware/CERA

S & F brass chromium plated tubular towel ring, fancy type complete all as specified and directed. (Make: PRAYAG Cat NO BA-21 or equivalent of Parryware /Hindware/Cera)

S & F health faucet brass body including wall hook, cast copper alloy & 1 metre long flexible stainless steel braided connection pipe suitable for 15mm bore pipe complete all as specified and directed. Make CERA Cat No F 8030301 or equvelent of Make : Hindware/Parryware/Prayag

S&F in repair 110 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S & F 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

E/M PORTION : - (EARTH WORKS AND CONCRETE WORKS IF ANY RELATED TO E/M WORKS SHALL BE MEASURED AND PAID UNDER RESOECTIVE ITEM CATERED IN B/R PORTION) : Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium grade) on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor (FRLS) earth continuity conductor to common earth and connecting to earth dolly all as specified for :- One light or fan point controlled by one 5 Amps switch one way

All as per item No 106 above but for one 3 pin socket point 5 Amp on independent board

Supply and fix Switch piano, flush button single pole, 5 Amps one way. Make : Anchor/Cabtree/Legrand/ Standard

Supply and fix Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC blocks. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Fan regulator electronic, step & socket type 230 volt, suitable for 1200/1400mm sweep ceiling fan. Make : Anchor/Cabtree/Legrand/ Standard

Supply and fix Sheet metal enclosure (ISI marked) distribution board for 240 volts, 2 way with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

S&F in replacement Pride plus inverter batten of make Havells, LED tube light fitting of 20 watts 6500K , 230 volt, with polycarbonate channel , lithium Ion battery with charging time 8-10 hours and back up time 4 hours complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Havells Cat No LHEXACP7FN1W020 OR equivelant of make Shakti/Crompton Greaves/Bajaj

S&F in replacement ULTRA SLIM square profile E-lite LED pride plus neo tube light fitting of make Havells, 9/10 watts 6500K , 230 volt, with polycarbonate channel environmental freindly, energy efficiency complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Havells Cat No LHEXACP7IN1W010 OR equivelant of make Shakti/Crompton Greaves/Bajaj

S&F new generation energy saving environmental friendly long life, with high power LED building street light/security light 1x 30/25 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 protection and impact resistant of IK7 prewired with all accessories and connection up with 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make:- Superb street light of Havells Cat No LHEXAYP7PN6K030 or equivelent of Bajaj/phillips/CG

S&F security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply & Fixing star rated energy saving ceiling fan 1200mm sweep (white) with all accessories and hanging the ceiling fan from fan hook with 3 core flexible copper wire 24/0.20 sqmm from ceiling rose, etc all as directed. Make : Model ES-50 of Havells or equivalent in Usha/Orient/Crompton.

Supply and Fixing exhaust fan, 300mm sweep metal body, AC single phase 230/240 Volt including bird free louver shutter cut to fit with hole for exhaust fan including providing holes grouting bolts and 3 core flexible copper conductor cable of size 24/0.20 sqmm connecting up from ceiling rose to exhaust fan terminal complete all as directed. Make : - Usha/almonard/Crompton/Khaitan/Bajaj. NOTE: - Quoted rate deemed to be inclusive of making hole for providing exhaust fan in wall including making good and necessary fixing arrangement of louvre using nut, bolts, washers etc complete.

S & F 25 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 455 gms) complete all as specified and directed.

M & L for Sand cushioning and covering with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, locally available best quality bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

S&F in replacement mild steel galvanized pipe light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 40mm bore dia.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, 2 core, nominal cross sectional area of main conductor 10 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

M&L, Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

SRI MAHALAKSHMI CONSTRUCTIONS

SHREE BANASHANKARI ASSOCIATES

Srisrinivasaenterprises