REPAIR AND MAINT OF LT PANELS APFC PANELS AND CONNECTED WORK AT ZONE I AND ZONEII AND VARIOUS ASCON NODES AND REPAIRS TO DOORS WINDOWS PLASTERING AND CERTAIN OTHER WORK IN ZONEII UNDER GE ARMY JAISALMER

Amount

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 20 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls, including suitable range of MCBs for Capacitor, contactor, AFPC relay etc with locking arrangement made out of 3.15 mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 25 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls, including suitable range of MCBs for Capacitor, contactor, APFC relay etc with locking arrangement made out of 3.15mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 30 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls, including suitable range of MCBs for Capacitor, contactor, APFC relay etc with locking arrangement made out of 3.15 mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 40 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls, including suitable range of MCBs for Capacitor, contactor, APFC relay etc with locking arrangement made out of 3.15 mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 60 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls,including suitable range of MCBs for Capacitor, contactor APFC relay etc with locking arrangement made out of 3.15mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 90 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls, including suitable range of MCBs for Capacitor, contactor, APFC relay etc with locking arrangement made out of3.15 mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 120 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls, including suitable range of MCBs for Capacitor, contactor, APFC relay etc with locking arrangement made out of 3.15 mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

Supply, installation, testing and commissioning of Capacitor panel board to adjust the capacity of 160 kvar capacitor bank cubical type suitable size depth not less than 0.60 M fatory made (CPRI approved), out door use double door , back side& front both side openabile in to two halve, inner door for individual controls, including suitable range of MCBs for Capacitor, contactor, APFC relay etc with locking arrangement made out of 3.15 mm thick CRCA Sheet supported on , 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof,well ventelated with exhaust fan of suitable size complete, powder coated with aluminium bus bar 4 Nos,300 Amps capacity duly PVC sleaved with colour coading mounted on porcelain insulators with suitable size of PVC insulated copper cable control wiring and lugs duly mounted on PCC foundation to match the existing feeder pilar complete and including dismantling and taking down old unserviceable existing LT capacitor panel board to accommodate and including the following :-

S&F APFC relay, 5 VA, 415 Volts, AC 8 Steps, testing, installation & programing complete and including taking down existing relay all as specified & directed by Engr-in-Charge. (Make :- L&T Cat Part No. ERPML08D500 or equvalent Havells/Siemens).

S&F APFC relay, 5 VA, 415 Volts, AC 12 Steps,testing, installation & programing complete and including taking down existing relay all as specified & directed by Engineer-in-charge. (Make :- L&T Cat Part No. ERPML12D500 or equivalent Havells/Siemens as approved by GE).

S & F LT cable route indicator made out of cast iron plate of 150 mm dia 4 thick having embosed wiriting LT cable fixed on MS angle iron 30x30x5 mm of 900 mm long with two nuts,bolts and grouting 500 mm length under ground and splitted and bent to shape and embedded in ground with PCC (15 cmx 15cm x 15 cm complete all as specified and directed.

S&F programmeable Digital meter (VAF type) for digital parameter such as voltage, Ampere, Power factor, Frenquency, KWH, 3 Phase, Class 0.5, 5 Amps complete, testing, installation & programing complete and including taking down existing meter all as specified & directed by Engr-in-Charge. (Make :- L&T Cat Part No WDV 303FC000/Legrand, Havells/Selec).

S&F in repair MCCB, 100 Amps, four pole,16 KA, 415 volt with fixed thermal maganetic release including taking down old existing MCCB all as specified and directed by Engineer-in- Charge. Note: ICS = ICU 100%.(Make:-L&T/ Legrand/ABB/Siemens).

S&F in repair MCCB, 160 Amps, four pole, 16 KA, 415 volt with fixed thermal maganetic release including taking down old existing MCCB all as specified and directed by Engineer-in- Charge. Note: ICS = ICU 100%.(Make:-L&T/Legrand/ABB/Siemens).

S&F in repair MCCB, 200 Amps, four pole, 25 KA, 415 volt with fixed thermal maganetic release including taking down old existing MCCB all as specified and directed by Engineer-in- Charge. Note: ICS = ICU 100%.(Make:- L&T/Legrand/ABB/Siemens).

S&F in repair MCCB, 250 Amps, four pole, 35 KA, 415 volt with fixed thermal maganetic release including taking down old existing MCCB all as specified and directed by Engr-in- Charge.Note: ICS = ICU 100%.(Make:- L&T/Legrand/ABB/Siemens).

S&F MCB three pole, 32 Amps, three pole, 415 Volts, 10 KA complete including taking down old existing MCB all as specified & directed by Engr-in-Charge. (Make : - Havells/L&T/Legrand/ ABB).

S&F capacitor MO C type contactor, low operating losses high withstand capacity for upto 8.5 KVAR complete including taking down old existing capacitor all as specified & directed by Engr-in-Charge. (Make :- L&T/Havells/Legrand/C&S).

S&F capacitor MO C type contactor, low operating losses high withstand capacity for upto 12.5 KVAR complete including taking down old existing capacitor all as specified & directed by Engr-in-Charge. (Make :- L&T/Havells/Legrand/C&S).

S&F capacitor MO C type contactor, low operating losses high withstand capacity for upto 15 KVAR complete including taking down old existing capacitor all as specified & directed by Engr-in-Charge. (Make :-L&T/Havells/Legrand/C&S).

S&F Auxilary contacts 415 Volt, 10A complete fixing with contactor of suitable size complete all including taking down old existing Axilary contacts as specified and directed by Engr-in-Charge.(Make : L&T/Havells/C&S/Legrand).

S&F in replacement of following standard duty power capacitors suitable for 440 Volt complete fixing to existing capacitor Panel complete including taking down old existing capacitors all as specified and directed by Engr-in-Charge.

(a) 10 Kvar

(b) 5 Kvar

(c) 2 Kvar

(d) 1 Kvar

Taking down the old existing unsv LT Cable of any size etc all as specified and directed by Engr-in-Charge.

Supply,Laying of XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) with aluminium conductor 1100 volts grade 50 Sqmm 3.5 core complete all as specified and directed by Engr-in-Charge.

--- ditto --- all as per item No. 24.00 above but of 70 Sqmm 3.5 Core.

--- ditto --- all as per item No.24.00 above but of 95 Sqmm 3.5 Core.

Excavation in trenches in soft/disintegrated rocks not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of cable/pipe etc or soil for shaft, walls, cesspts, manholes, pier holes etc not exceeding 10 sqm on plan and getting out complete all as specified & directed by Engr-in-Charge.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as directed by Engr-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick soft/disintegrated soil in any type of soil all as specified & directed by Engr-in-Charge.

M&L for sand cushioning to underground PVC/XLPE cable with tibba sand and punning to provide required cover complete all as directed by Engr-in-Charge.(Note :- For the purpose of payment only punned thickness will be measured).

Supplying and laying Jodhpur stone quarry faced stone slab cover 25 to 30 cm in width, 50 to 60 cm long and 40 to 50 mm thick, laid dry and abutting each other with gap between adjacent slab not exceeding 10 mm over under ground cables for protection complete all as specified & directed by Engr-in-Charge.

Supply,jointing and testing outdoor type heat shrinkable end teriminal cable joint including all material and accessories suitable for 3.5 core 16 to 35 Sqmm of 1100 Volts grade all as per manufacture recommendation complete all as specified and directed.Make :- Dension/M seal/Raychem.

All as per item No 32 above here-in-before but suitable size for 3.5 Core 50 to 95 Sqmm.

All as per item No. 32 above here-in-before but suitable size for 3.5 Core 120 to 185 Sqmm.

Taking down the old existing unsv LT Panel of any capacity size etc all as specified and directed by Engr-in-Charge.

Supply, installation, commissioning and testing of LT FP box (CPRI Approved) outdoor type 415 Volts, 50 Hz, 3 Phase 4 wire supply Padastal mounted double door center opening with lockng arrangement , factory assembled,CPRI approved, weather and vermin proof (protection class IP-54) canopy on top, outer door made out of 3.15 mm thick CRCA sheet for individual hinged type door for MCCBs , powder coated and supported on 50 mm x 50 mm x 6 mm angle iron frame and 3.15 mm thick MS rubber beading , complete to accommodate including the following:-

Supply, installation, commissioning and testing of LT FP box (CPRI Approved) outdoor type 415 Volts, 50 Hz, 3 Phase 4 wire supply Padastal mounted double door center opening with lockng arrangement , factory assembled,CPRI approved, weather and vermin proof (protection class IP-54) canopy on top, outer door made out of 3.15 mm thick CRCA sheet for individual hinged type door for MCCBs , powder coated and supported on 50 mm x 50 mm x 6 mm angle iron frame and 3.15 mm thick MS rubber beading , complete to accommodate including the following:-

Supply, installation, commissioning and testing of LT FP box (CPRI Approved) outdoor type 415 Volts, 50 Hz, 3 Phase 4 wire supply Padastal mounted double door center opening with lockng arrangement , factory assembled,CPRI approved, weather and vermin proof (protection class IP-54) canopy on top, outer door made out of 3.15 mm thick CRCA sheet for individual hinged type door for MCCBs , powder coated and supported on 50 mm x 50 mm x 6 mm angle iron frame and 3.15 mm thick MS rubber beading , complete to accommodate including the following:-

Supply, installation, commissioning and testing of LT FP box (CPRI Approved) outdoor type 415 Volts, 50 Hz, 3 Phase 4 wire supply Padastal mounted double door center opening with lockng arrangement , factory assembled,CPRI approved, weather and vermin proof (protection class IP-54) canopy on top, outer door made out of 3.15 mm thick CRCA sheet for individual hinged type door for MCCBs , powder coated and supported on 50 mm x 50 mm x 6 mm angle iron frame and 3.15 mm thick MS rubber beading , complete to accommodate including the following (12RSR):-

Supply, installation, commissioning and testing of LT FP box (CPRI Approved) outdoor type 415 Volts, 50 Hz, 3 Phase 4 wire supply Padastal mounted double door center opening with lockng arrangement , factory assembled,CPRI approved, weather and vermin proof (protection class IP-54) canopy on top, outer door made out of 3.15 mm thick CRCA sheet for individual hinged type door for MCCBs , powder coated and supported on 50 mm x 50 mm x 6 mm angle iron frame and 3.15 mm thick MS rubber beading , complete to accommodate including the following (12RSR):-

Taking down Chowkhats or frames n.exc 1.50sqm each with shutters (without taking off shutters from the frames) including taking off the old fasts complete all as specified.

Taking down Chowkhats or frames .exc 1.50sqm but n.exc 4sqm each with shutters (without taking off shutters from the frames) including taking off the old fasts complete all as specified.

Taking down shutters of any description n.exc 1.0sqm each.

All as per item No.3 above but exc 1.0sqm and n.exc 2.0sqm each.

Hacking out old broken glass (any thickness, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads.

All as per item No.5 above but from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

S & F Steel windows with side hung sgutters uncluding projecting type hinges with steel handles, and steel peg stay complete with glazing bars, dovetailed or welded.

All as per item No.47 above but without glazing bars.

S & F Steel Ventilators with top hung shutters including hinges, steel peg stay complete.

S&F Steel windows or ventilators, fixed type, with glazing bars.

S&F Mild steel framed work such as grills, gratings, etc with ends of bars shiuldered and/or riveted, or forged into spikes, framed guard bars, etc conforming to Fe-290, Gde-E-165.

S&F Mild stell work as in hold fasts complete conforming to Fe-290, Gde-E-165.

S&F 105mm X 600mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified.

S&F 125mm X 600mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified.

S&F Factory made solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fixinf in openings as per specifications & drawings.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes eor top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rails & bottom rails on either side & as gap insert eor top rail & bottom rail. panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVc sheet beading, and jointed together with solvent cement, supplied and fixing in the frame at site as per specifications & drawings.

S&F 35mm thick 2nd class hard wood factory made plain framed, panneled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stiles as per IS-1003 (Part-I0, kiln seasoned and chemically pressure treated.

M&L 35mm thick 2nd class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (with out sash bars), edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSr Part-I, section 8, clause 8.24(a) supplied and fixed to chowkhats.

M&L 30mm thick 2nd class hard wood factory made glazed and skelton shutters divided into squares with plain chamfered or rounded mitred and rebate sash bars any numbers in wendow, ventelator etc provided with stiles rails all as specified.

S&F 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

M&L fixed in repair 18/19 thick Prelaminated Particle board, interior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work.

S&F 1st class hard wood small fittings such as bracjets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labour, articles n.exc 200cu cm each.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel and fixed.

All as per item No.63 above but 75mm size.

All as per item No.63 above but 50mm size.

S&F brass 40mm(width of flaps) Continuous (piano) hinges.

S&F 40mm dia ,brass cup board knobs fixed with nut, screwand washer of brass.

S&F 125mm Hasp and staple,safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws.

S&F300mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed.

S&F150mm long aluminium anodised barrel tower bolts of extruded section and fixed.

S&F125mm long aluminium anodised barrel tower bolts of extruded section and fixed.

S&F150mm size extruded aluminium alloy handles, fabricated type, anodised.

S&F125mm size extruded aluminium alloy handles, fabricated type, anodised.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, overall length of cover plare 140mm.

S&F mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel nut & bolt to steel window / ventilater.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aserture 1.40mm and fixed with stainless steel note both to steel window/ventilator and wire staple on wooden frame fixed in repair.

S&F 3mm thick sheet glass ordinary qyality and glazing with oil putty in square n.exc 0.50 sqm in each pane.

M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in bed blocks for hold fasts etc.

M&L for two coats of synthetic enamel paint over a coat of wood primer on new wooden surfaces of any description, not other wise described, over 10cm width or girth including preparation of surfaces.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description, not other wise described, over 10cm width or girth including preparation of surfaces.

Taking down aluminium anodised door,window and ventilator.

S&F Aluminium anodised frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F aluminium anodised window and ventilator shutters,fixed type without sash bar aluminium section wt 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised snap beading , screws etc, complete all as specified.

S&F Anodised aluminium door shutters,aluminium section wt 0.55 kg/m including necessary jointing cleats ,glazing clips rubber neoprane packing ,handles 2 Nos in each door hinges, anodised aluminium snap beading screws etc complete all as specified.

S&F 5.5mm thick sheet glass ordinary quality.

S&F solar control film 50 micron reflective type sicked to glass panes as per instruction of manufacturers.

S&F Aluminium anodised butt hinges 125mm long.

S&F 100mm brass 4 Levers mortice lock vertical type.

S&F in repair 100mm brass 4 Levers mortice lock vertical type.

S&F Aluminium (Die cast ) body door closer hydraulically regulated, desigantion No. 3, universal type, Suitable for door shutters of 851 to 1000mm in width and weight between 61to 80Kg.

S&F in repair Aluminium (Die cast ) body door closer hydraulically regulated, desigantion No. 3, universal type, Suitable for door shutters of 851 to 1000mm in width and weight between 61to 80Kg.

S&F mild steel 300mm,ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F megnatic catch for cup board shutter.

M&L Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover,governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

Taking down cement plaster on brick walls , including racking out joints, hacking for key, scrubbing down with water etc.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for 25mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in flooring.

M&L for 10mm thick rendering in CM 1:4 for backing coat for laying wall tiles.

M&L for 15mm thick screed bed or bedding layer of cement mortar in CM 1:6 for laying floor finish.

Material and labour for 300x300x7mm thick non skid joint less ( vertical joints) ceramic tiles coloured set and jointed in neat cement slurry and pointed in coloured cement as in floor all as specified.

Material and labour for 450 x 300 x 7mm thick joint less (vertical joint ) glazed ceramic tiles coloured set and jointed in neat cement slurry and pointed in coloured cement as in skirting/dado all as specified.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth with out using extra cement.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth with out using extra cement.

M&L for threecoats of white wash on newly plastered wall surfaces including preparation of surfaces.

M&L for one coat of white wash on old wall surfaces including preparation of surfaces.

M&L for two coats of oil bound distemper on newly plastered surfaces over a coat of chalk whiting , including preparation of surfaces.

M&L for one coat of oil distempering on old wall surfaces including preparation of surfaces.

M&L for two coat of cement base paint on newly plastered surface .

Supply only Integral water proofing compound.

S&F factory made sloid PVC core plastic ply 18mm thick with plain colour laminated PVC sheet on both face fixed in repair Make-: Rajshri/Sintex

S&F solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing

S&F 5mm thick PVC sheet fillet of width 50mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing

M&L for repairs of rolling shutter any type (push pull or manual or gear operated ) after opening hood cover and without taking down rolling shutter by cleaning greasing oiling and replacement of rusted nut bolts including welding as requires for smooth function for area n exc 5 Sqm each

All asper item no 115 above but exc 5 Sqm but n exc 10sqm each

M&L for oiling and greasing to the MS shutters by removing the scales and to make the shutters swing freely

Repairs to MS door shutter weighing 750-1000 kg to swing freely which obstructing the movement due to pintel hinges is inclined inner words to align the shutter by means of hammering/welding/oiling /lifting the shutter by means of pully or crane by taking saftey measures.

S&F in repairs MS wheel of size 125mm dia and 32mm thick to the bottem of MS shutter by welding /nut & bolting by taking fire safety precautions

Taking down unserviceable rolling shutters of any descrioption any size height upto 4 meters

Taking down unserviceable rolling shutters of any descrioption any size height more than 4 meters

S&F steel rolling shutters without ball bearig as specified incl top cover, anchoring rod, Hasp and stapple and one shop coat of primer, erected in position as indicated, complete push pull or manual type using 1.25 mm thick laths

All as per item no 122 above but gear operated type with bevel gear box and crack handle

S&F Ball bearing for rolling shutter

S&F rolled mild steel framed work as in door or gates of angle or other section confirming to Fe 410-S with gusset plates, rail braces etc complete drilled for fixing of steel sheeting or other covering and hanging and fixing complete.

S&F safety lever lockers mild steel with 4 levers for rolling shutters

S&F in repair MS powder coated drapery rod 25mm dia decorative manner all as per sample and all as specified and directed by Engr in charge

S&F for Brackets powder coated fancy type for drapery rod all as specified and directed by Engr in charge.

M&L for ceiling with 12mm thick Gypsum Board incl GI frame works etc all as specified and cornices at junctions and 2 coat of plastic emulsion paint over a coat of primer incl cornices moulding etc fixed in repairs, all as specified and directed by Engr in charge.

Repair of steel window shutter not exc 1.5 Sqm each by replacing projected type unserviceable hinges, with welding new hinges or welding of existing broken hinges and handles to window frames and easing of shutters to proper closing with oiling to hinges and painting at welded portion to match the existing surfaces each.

All as item 130 above but ventelator shutter not exc 1 Sqm each.

Resecuring or easing and adjusting shutters of any description exc 1 Sqm and not exc 3 Sqm each without taking down of sutters.

Supply and fix in repairs Aluminiumn anodised barrel tower bolts 200mm length of extruded section

All as item 133 above 125 mm length

S&F in repairs Aluminium alloy, anodised, sliding door bolt plate with hasp and staple (bolt type), 300mm size and fixing in clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as specified.

S&F in repairs butt hinges 100mm size medium weight cold rolled ms in any type of chowkat or frame including welding if required all as specified and as directed.

All as item 136 above 75mm size

S&F in repairs 300mm, ordinary rat tail rod pattern springs, including roller and rooler plate complete including welding if required for fixing in case of pressed steel chowkat all as specified and as directed.

S&f in repairs 150mm size extruded aluminium alloy handles fabricated type, anodised.

All as item 139 above but 100 mm size

Repair of aluminium shutter of any description and size including taking out the shutters and refixing in the same opening and easing of shutters to proper closing with oiling to hinges, floor springs etc all as specified and as directed by Engr in charge

M&Lsteel door stoper double shoe fixed in door shutters all as directed fixed in repairs.

S&Fin repair steel window handle left and right complete fitting

S&Fin repair steel window stopper peg stay complete.

Steel lock with two keys as per Godrej pattern.

S&F in repair 3mmthick looking glass for built-in almirah.

Dismantling (AC corrugated , semi corrugated etc ) AC sheets in roof coverings complete all as specified & directed by Engineer in charge.

S&F Pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet/ semi corrugated 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws as specified.

JASOL MAA ENTERPRISES

M/s Shree Construction Company

S R ENTERPRISES

Sachiyay maa Electricals

M/S SHRI HARI CONSTRUCTION COMPANY

M/S JAGDAMBA ENTERPRISES

M/S PRASHANT BENIWAL