NIT 1166 PMGSY Road Renewal Maintenance PKG No CG 24 M-56 District- Balrampur

Amount

Cutting of branches of trees shrubs and trimming of grass and weeds. Trimming of grass and weeds from the shoulder/berms and disposing off the same to suitable locations as per technical specification clause 1914.

Restoration of rain cuts Restoration of rain cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh material in layers not exceeding 250 mm and compaction with plate compactor or power rammer to restore the original alignment, level and slopes as per drawings and technical specifications Clause 1902

Scarifying Existing Granular bituminous Surface to a Depth of 100 mmScarifying existing granular/bituminous surface upto a depth of 100 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

Maintenance of WBM road including filling up of pot holes ,ruts and rectifying corrugated surface ,damaged edges and raveling as per technical specification clause 1906

Prime Coat Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Maintenance of Bituminous surface road (III) Repair to Pot holes and removal of loose material , trimming of sides, cleaning of surface by providing tack coat , 20 mm thick pre-mix carpet and seal coat type B specification clause 1904.2 (Deduct for seal coat Type B as per SOR Item No 11.14 1 (IV) By Mechanical Means Case - II :Type B (ii) Bitumen (VG-30))

Periodical Renewal to existing bituminous surface 1 Open graded Premix Carpet 20 mm thick (I) Tack coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503

Pre-mix carpet using bituminous (penetration grade modified bitumen) binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of aggregate 13.2mm size (passing 22.4mm size sieve & retained on 11.2mm sieve and 11.2mm size (passing 13.2mm sieve and retained on 5.6mm sieve) either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. By Mechanical Means (II) Bitumen (VG-30)

Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 Case - II : Type B (II) Bitumen (VG-30)

Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509, Viscocity grade (VG) Bitumen specification as per IS 73:2006 Type B (II) Bitumen (VG-30)

Construction of Plain Cement Concrete Drain with PCC grade M-15 including all shuttering/form work etc. complete as per drawings/technical specification and direction of engineer in chargePCC side drain of sectional area = 0.25 sqm. (sectional detail attached) RD- 0 M- 3600 M

Maintenance of Road Signs by way of cleaning and repainting of mandatory / regulatory /cautionary / informatory and place identifications sign board as per drawing and technical specification clause 1910.

Maintenance of 200 metre km stones by way of refitting of tilted stones repairing with cement mortars ,cleaning repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification clause 1912. (i) Painting two coats with synthetic enamel paint

Maintenance of 200 metre km stones by way of refitting of tilted stones repairing with cement mortars ,cleaning repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification clause 1912. (ii) Printing letters and figures of any shade with synthtic enamel paint of any approved colour to give an even shade

Cautionary, mandatory, informatory direction and place identification sign boards. Semi-Reflective Traffic signs more than 0.90 sqm sign board Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm of 12 SWG square tube of 3050 mm height duly strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Cautionary, mandatory, informatory direction and place identification sign boards. Semi-Reflective Traffic signs upto 0.90 sqm Direction and place indentification signs upto 0.9 sqm size board. providing and erecting direction and place identification of semi reflective sign boards as per IRC : 67 made of 2mm thick MS sheet duly stove enameled paint in white colour in front and grey colour in back with red reflective border of 70 mm width and required message , letters and figures with reflective engineering grade tape as per MORD specifications of required shades and colour . Supported and welded on 47mm x 47mm x 12 SWG square tube of 3050 mm height duly strengthened by 25mm X 5mm M/s Flat iron on edges on back firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600mm , 600 mm below ground level as per approved drawing and technical specification clause 1701.

Providing typical PMGSY informatory & Logo Board of PMGSY project (B) Providing and fixing of typical PMGSY informatory sign board with logo as per MORD specifications and drawing . Three MS platess of 1.6mm thick , top and middle plate duly welded with MS flat iron 25 mm x 5m size on back on edges . The lower plate will be welded with MS anfle iron frame of 25 mm x 25mm x 5mm . The angle iron frame of th elower most plate and flat iron frame of middle plate will be welded to 2 nos 75 mm of 12 SWG sheet tubes post duly embedded in cemen concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level . the top most diamond plate will be welded to middle plate by 47 mm x 47 mm of 12 SWG steel plate tube . All MS will be stoved enemeled on both sides . Lettering and printing arrows border etc will be painted with ready mixed synthetic enameled paint of superior quality in required shades and colour . ALL section of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1

Providing and fixing Citizen informatory board Of PMGSY project (A) Providing and fixing of typical PMGSY citizen informatory board with logo as per MORD specification and drawings made of 75 mm square or 75 mm dia circular steel tube of 12 SWG 3.2 m height and cross member 2 NOs. 1 m long fixed with angle iron 50 x 50 x 5 mm MS angle on the back .

Kilometer stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 (I) 5th KM stone (precast)

Reinforced cement concrete M15 grade Guard Stone of size 200 mm x 200mm x 800 mm fixing in position including painting and printing etc. as per drawing, Technical Specification and as per direction of Engineer in Charge. RD:- 0 M - 9000 M

Providing & Fixing of PMGSY 'Logo' board Providing and fixing of typical PMGSY logo board as per MoRD specifications and drawings.

Boundary Pillar Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704

Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908

Maintenance of Slab type Culverts by way of clearing, Cleaning, Erosion repair, repairs to cracks, parapet walls and Protection works as per drawing and technical specification Clasue 1908

Maintenance of Causeway by way of minor Surface repairs, replacing guide posts, repair of flood gauges, removal of debris, providing Boulders and protection work and painting as per technical specification Clause 1909

White washing two coats on parapet walls of CD and tree trunk including preparation of surface by cleaning scraping etc as per technical specification clause 1915.

Excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary Soil (i) Upto 3m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (I) P.C.C. grade M10 (Nominal Mix 1:3:6)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (II) P.C.C. grade M15 (Nominal Mix 1:2.5:5)

Bedding for Causeway/Pipes (II) Type B (First Class) Bedding Laying (First Class) Bedding with well compacted sand , moorum or approved granular material as per clause 1105(ii)

Providing and laying reinforced cement concrete pipe NP3 for Culverts/ Burried conduits on first class bedding of granular material including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1106. (A) 600 mm Dia

Dismentaling of Structures Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete , wood work , steel work, including T & P and scaffolding wherever necessary , sorting the dismentled material , disposal of unservicable material and stacking the serviceable material with all lift and lead of 1000 m as per technical specification clause 202. ( B ) Cement Concrete

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clause 802, 804, 805, 806, 807, 1202 & 1204 For hight up to 5m (i) P.C.C grade M 15 (1:2.5:5) Upto 3m depth

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height ,compacted to firm condition complete as per drawing and technical specification clause 1204.3.8

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification clause 614,709,1204.3.7

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 (I) Granular material

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 (I) RCC Grade M-20 (i) For Nominal Mix 1:2:4

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 (II) R.C.C M 25

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3

Filling in foundation trenches as per drawing and technical specification clause 1108 & 305.3.9 (II) Earth filling

Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications

Description of Item

Amount

Cutting of branches of trees shrubs and trimming of grass and weeds. Trimming of grass and weeds from the shoulder/berms and disposing off the same to suitable locations as per technical specification clause 1914.

Restoration of rain cuts Restoration of rain cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh material in layers not exceeding 250 mm and compaction with plate compactor or power rammer to restore the original alignment, level and slopes as per drawings and technical specifications Clause 1902

Scarifying Existing Granular bituminous Surface to a Depth of 100 mmScarifying existing granular/bituminous surface upto a depth of 100 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

Maintenance of WBM road including filling up of pot holes ,ruts and rectifying corrugated surface ,damaged edges and raveling as per technical specification clause 1906

Prime Coat Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Maintenance of Bituminous surface road (III) Repair to Pot holes and removal of loose material , trimming of sides, cleaning of surface by providing tack coat , 20 mm thick pre-mix carpet and seal coat type B specification clause 1904.2 (Deduct for seal coat Type B as per SOR Item No 11.14 1 (IV) By Mechanical Means Case - II :Type B (ii) Bitumen (VG-30))

Periodical Renewal to existing bituminous surface 1 Open graded Premix Carpet 20 mm thick (I) Tack coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503

Pre-mix carpet using bituminous (penetration grade modified bitumen) binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of aggregate 13.2mm size (passing 22.4mm size sieve & retained on 11.2mm sieve and 11.2mm size (passing 13.2mm sieve and retained on 5.6mm sieve) either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. By Mechanical Means (II) Bitumen (VG-30)

Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 Case - II : Type B (II) Bitumen (VG-30)

Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509, Viscocity grade (VG) Bitumen specification as per IS 73:2006 Type B (II) Bitumen (VG-30)

Construction of Plain Cement Concrete Drain with PCC grade M-15 including all shuttering/form work etc. complete as per drawings/technical specification and direction of engineer in chargePCC side drain of sectional area = 0.25 sqm. (sectional detail attached) RD- 0 M- 3600 M

Maintenance of Road Signs by way of cleaning and repainting of mandatory / regulatory /cautionary / informatory and place identifications sign board as per drawing and technical specification clause 1910.

Maintenance of 200 metre km stones by way of refitting of tilted stones repairing with cement mortars ,cleaning repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification clause 1912. (i) Painting two coats with synthetic enamel paint

Maintenance of 200 metre km stones by way of refitting of tilted stones repairing with cement mortars ,cleaning repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification clause 1912. (ii) Printing letters and figures of any shade with synthtic enamel paint of any approved colour to give an even shade

Cautionary, mandatory, informatory direction and place identification sign boards. Semi-Reflective Traffic signs more than 0.90 sqm sign board Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm of 12 SWG square tube of 3050 mm height duly strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Cautionary, mandatory, informatory direction and place identification sign boards. Semi-Reflective Traffic signs upto 0.90 sqm Direction and place indentification signs upto 0.9 sqm size board. providing and erecting direction and place identification of semi reflective sign boards as per IRC : 67 made of 2mm thick MS sheet duly stove enameled paint in white colour in front and grey colour in back with red reflective border of 70 mm width and required message , letters and figures with reflective engineering grade tape as per MORD specifications of required shades and colour . Supported and welded on 47mm x 47mm x 12 SWG square tube of 3050 mm height duly strengthened by 25mm X 5mm M/s Flat iron on edges on back firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600mm , 600 mm below ground level as per approved drawing and technical specification clause 1701.

Providing typical PMGSY informatory & Logo Board of PMGSY project (B) Providing and fixing of typical PMGSY informatory sign board with logo as per MORD specifications and drawing . Three MS platess of 1.6mm thick , top and middle plate duly welded with MS flat iron 25 mm x 5m size on back on edges . The lower plate will be welded with MS anfle iron frame of 25 mm x 25mm x 5mm . The angle iron frame of th elower most plate and flat iron frame of middle plate will be welded to 2 nos 75 mm of 12 SWG sheet tubes post duly embedded in cemen concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level . the top most diamond plate will be welded to middle plate by 47 mm x 47 mm of 12 SWG steel plate tube . All MS will be stoved enemeled on both sides . Lettering and printing arrows border etc will be painted with ready mixed synthetic enameled paint of superior quality in required shades and colour . ALL section of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1

Providing and fixing Citizen informatory board Of PMGSY project (A) Providing and fixing of typical PMGSY citizen informatory board with logo as per MORD specification and drawings made of 75 mm square or 75 mm dia circular steel tube of 12 SWG 3.2 m height and cross member 2 NOs. 1 m long fixed with angle iron 50 x 50 x 5 mm MS angle on the back .

Kilometer stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 (I) 5th KM stone (precast)

Reinforced cement concrete M15 grade Guard Stone of size 200 mm x 200mm x 800 mm fixing in position including painting and printing etc. as per drawing, Technical Specification and as per direction of Engineer in Charge. RD:- 0 M - 9000 M

Providing & Fixing of PMGSY 'Logo' board Providing and fixing of typical PMGSY logo board as per MoRD specifications and drawings.

Boundary Pillar Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704

Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908

Maintenance of Slab type Culverts by way of clearing, Cleaning, Erosion repair, repairs to cracks, parapet walls and Protection works as per drawing and technical specification Clasue 1908

Maintenance of Causeway by way of minor Surface repairs, replacing guide posts, repair of flood gauges, removal of debris, providing Boulders and protection work and painting as per technical specification Clause 1909

White washing two coats on parapet walls of CD and tree trunk including preparation of surface by cleaning scraping etc as per technical specification clause 1915.

Excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary Soil (i) Upto 3m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (I) P.C.C. grade M10 (Nominal Mix 1:3:6)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (II) P.C.C. grade M15 (Nominal Mix 1:2.5:5)

Bedding for Causeway/Pipes (II) Type B (First Class) Bedding Laying (First Class) Bedding with well compacted sand , moorum or approved granular material as per clause 1105(ii)

Providing and laying reinforced cement concrete pipe NP3 for Culverts/ Burried conduits on first class bedding of granular material including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1106. (A) 600 mm Dia

Dismentaling of Structures Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete , wood work , steel work, including T & P and scaffolding wherever necessary , sorting the dismentled material , disposal of unservicable material and stacking the serviceable material with all lift and lead of 1000 m as per technical specification clause 202. ( B ) Cement Concrete

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clause 802, 804, 805, 806, 807, 1202 & 1204 For hight up to 5m (i) P.C.C grade M 15 (1:2.5:5) Upto 3m depth

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height ,compacted to firm condition complete as per drawing and technical specification clause 1204.3.8

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification clause 614,709,1204.3.7

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 (I) Granular material

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 (I) RCC Grade M-20 (i) For Nominal Mix 1:2:4

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 (II) R.C.C M 25

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3

Filling in foundation trenches as per drawing and technical specification clause 1108 & 305.3.9 (II) Earth filling

Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications

Description of Item

Amount

Cutting of branches of trees shrubs and trimming of grass and weeds. Trimming of grass and weeds from the shoulder/berms and disposing off the same to suitable locations as per technical specification clause 1914.

Restoration of rain cuts Restoration of rain cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh material in layers not exceeding 250 mm and compaction with plate compactor or power rammer to restore the original alignment, level and slopes as per drawings and technical specifications Clause 1902

Scarifying Existing Granular bituminous Surface to a Depth of 100 mmScarifying existing granular/bituminous surface upto a depth of 100 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

Maintenance of WBM road including filling up of pot holes ,ruts and rectifying corrugated surface ,damaged edges and raveling as per technical specification clause 1906

Prime Coat Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Maintenance of Bituminous surface road (III) Repair to Pot holes and removal of loose material , trimming of sides, cleaning of surface by providing tack coat , 20 mm thick pre-mix carpet and seal coat type B specification clause 1904.2 (Deduct for seal coat Type B as per SOR Item No 11.14 1 (IV) By Mechanical Means Case - II :Type B (ii) Bitumen (VG-30))

Periodical Renewal to existing bituminous surface 1 Open graded Premix Carpet 20 mm thick (I) Tack coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503

Pre-mix carpet using bituminous (penetration grade modified bitumen) binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of aggregate 13.2mm size (passing 22.4mm size sieve & retained on 11.2mm sieve and 11.2mm size (passing 13.2mm sieve and retained on 5.6mm sieve) either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. By Mechanical Means (II) Bitumen (VG-30)

Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 Case - II : Type B (II) Bitumen (VG-30)

Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509, Viscocity grade (VG) Bitumen specification as per IS 73:2006 Type B (II) Bitumen (VG-30)

Construction of Plain Cement Concrete Drain with PCC grade M-15 including all shuttering/form work etc. complete as per drawings/technical specification and direction of engineer in chargePCC side drain of sectional area = 0.25 sqm. (sectional detail attached) RD- 0 M- 3600 M

Maintenance of Road Signs by way of cleaning and repainting of mandatory / regulatory /cautionary / informatory and place identifications sign board as per drawing and technical specification clause 1910.

Maintenance of 200 metre km stones by way of refitting of tilted stones repairing with cement mortars ,cleaning repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification clause 1912. (i) Painting two coats with synthetic enamel paint

Maintenance of 200 metre km stones by way of refitting of tilted stones repairing with cement mortars ,cleaning repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification clause 1912. (ii) Printing letters and figures of any shade with synthtic enamel paint of any approved colour to give an even shade

Cautionary, mandatory, informatory direction and place identification sign boards. Semi-Reflective Traffic signs more than 0.90 sqm sign board Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm of 12 SWG square tube of 3050 mm height duly strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Cautionary, mandatory, informatory direction and place identification sign boards. Semi-Reflective Traffic signs upto 0.90 sqm Direction and place indentification signs upto 0.9 sqm size board. providing and erecting direction and place identification of semi reflective sign boards as per IRC : 67 made of 2mm thick MS sheet duly stove enameled paint in white colour in front and grey colour in back with red reflective border of 70 mm width and required message , letters and figures with reflective engineering grade tape as per MORD specifications of required shades and colour . Supported and welded on 47mm x 47mm x 12 SWG square tube of 3050 mm height duly strengthened by 25mm X 5mm M/s Flat iron on edges on back firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600mm , 600 mm below ground level as per approved drawing and technical specification clause 1701.

Providing typical PMGSY informatory & Logo Board of PMGSY project (B) Providing and fixing of typical PMGSY informatory sign board with logo as per MORD specifications and drawing . Three MS platess of 1.6mm thick , top and middle plate duly welded with MS flat iron 25 mm x 5m size on back on edges . The lower plate will be welded with MS anfle iron frame of 25 mm x 25mm x 5mm . The angle iron frame of th elower most plate and flat iron frame of middle plate will be welded to 2 nos 75 mm of 12 SWG sheet tubes post duly embedded in cemen concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level . the top most diamond plate will be welded to middle plate by 47 mm x 47 mm of 12 SWG steel plate tube . All MS will be stoved enemeled on both sides . Lettering and printing arrows border etc will be painted with ready mixed synthetic enameled paint of superior quality in required shades and colour . ALL section of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1

Providing and fixing Citizen informatory board Of PMGSY project (A) Providing and fixing of typical PMGSY citizen informatory board with logo as per MORD specification and drawings made of 75 mm square or 75 mm dia circular steel tube of 12 SWG 3.2 m height and cross member 2 NOs. 1 m long fixed with angle iron 50 x 50 x 5 mm MS angle on the back .

Kilometer stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 (I) 5th KM stone (precast)

Reinforced cement concrete M15 grade Guard Stone of size 200 mm x 200mm x 800 mm fixing in position including painting and printing etc. as per drawing, Technical Specification and as per direction of Engineer in Charge. RD:- 0 M - 9000 M

Providing & Fixing of PMGSY 'Logo' board Providing and fixing of typical PMGSY logo board as per MoRD specifications and drawings.

Boundary Pillar Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704

Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908

Maintenance of Slab type Culverts by way of clearing, Cleaning, Erosion repair, repairs to cracks, parapet walls and Protection works as per drawing and technical specification Clasue 1908

Maintenance of Causeway by way of minor Surface repairs, replacing guide posts, repair of flood gauges, removal of debris, providing Boulders and protection work and painting as per technical specification Clause 1909

White washing two coats on parapet walls of CD and tree trunk including preparation of surface by cleaning scraping etc as per technical specification clause 1915.

Excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary Soil (i) Upto 3m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (I) P.C.C. grade M10 (Nominal Mix 1:3:6)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (II) P.C.C. grade M15 (Nominal Mix 1:2.5:5)

Bedding for Causeway/Pipes (II) Type B (First Class) Bedding Laying (First Class) Bedding with well compacted sand , moorum or approved granular material as per clause 1105(ii)

Providing and laying reinforced cement concrete pipe NP3 for Culverts/ Burried conduits on first class bedding of granular material including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1106. (A) 600 mm Dia

Dismentaling of Structures Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete , wood work , steel work, including T & P and scaffolding wherever necessary , sorting the dismentled material , disposal of unservicable material and stacking the serviceable material with all lift and lead of 1000 m as per technical specification clause 202. ( B ) Cement Concrete

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clause 802, 804, 805, 806, 807, 1202 & 1204 For hight up to 5m (i) P.C.C grade M 15 (1:2.5:5) Upto 3m depth

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height ,compacted to firm condition complete as per drawing and technical specification clause 1204.3.8

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification clause 614,709,1204.3.7

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 (I) Granular material

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 (I) RCC Grade M-20 (i) For Nominal Mix 1:2:4

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 (II) R.C.C M 25

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3

Filling in foundation trenches as per drawing and technical specification clause 1108 & 305.3.9 (II) Earth filling

Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications

Description of Item

Amount

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and fixing 'Citizen Information Board' of PMGSY Project (A) Providing and fixing of typical " PMGSY Citizen Information Board" with Logo as per MoRD specifications & drawings, made of 75 mm square or 75 mm dia circular steel tube of 12 SWG 3.2 m height and cross member 2 nos 1m long, fixed with angle iron 50x50x5 mm MS angle on the back

Providing & Fixing of PMGSY 'Logo' board Providing and fixing of typical PMGSY logo board as per MoRD specifications and drawings.

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

Cautionary, mandatory, informatory, direction and place indentification sign boards Semi-Reflective Traffic signs up to 0.90 sqm size Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour. Supported and welded on 47 mm x 47mm of 12 SWG Square tube of 3050 mm height duly strengthened by 25 mm x 5 mm M/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Reinforced cement concrete M15 grade guard stone of size 200mmX200mmX800mm fixing in position including painting and printing etc as per drawing and technical specification and as per direction of engineer in charge.

Excavation for Structure as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I)Ordinary soil i. Upto 3 m depth

Bedding for causeway / pipes (II) Type B (First class) bedding Laying (First class) bedding with well compacted sand, moorum or approved granular material as per clause 1105 (ii)

Providing concrete for plain/reinforced concrete in open foundation complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 I. P.C.C grade M 10 (Nominal mix 1:3:6)

Providing concrete for plain/reinforced concrete in open foundation complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 II. P.C.C grade M 15 (Nominal mix 1:2.5:5)

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 For height upto 5 m I. P.C.C grade M 15 (Nominal mix (1:2.5:5)

Laying Reinforced Cement Concrete Pipe NP3 as per drawing and technical specification Clause 1402.6 Providing and laying reinforced cement concrete pipe NP3 for culverts on first Class bedding in single row including fixing with cement mortar 1:2 but excluding excavation, bedding protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm DIA

Laying Reinforced Cement Concrete Pipe NP3 as per drawing and technical specification Clause 1402.6 Providing and laying reinforced cement concrete pipe NP3 for culverts on first Class bedding in single row including fixing with cement mortar 1:2 but excluding excavation, bedding protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (A) 600 mm DIA

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 I) Granular material

Construction of Plain Cement Concrete Drain with P.C.C. grade M-15 including all shuttering/form work etc. complete as per drawings/technical specification and direction of engineer in charge.

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 R.C.C. grade M 20 1:2:4 R.C.C. Cover in front of houses (Length/6 M)

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 II. R.C.C M 25 (Design mix)

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 (12 MM) 80 KG /Cum Item No. 3

Providing weepholes in brick masonry/stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Dismentalling of structures Dismentalling of existing structures like bridges, culvert, retaining wall and other structures comprising of masonry, cement concrete, wood work, steel work including T&P and scaffolding wherever necessary sorting the dismentalled materials , disposal of unservicable materials and stacking the servicable material with all lifts and leads of 1000m as per technical specificatiopn clause 202 (B) Cement concrete

Dismentalling of structures Dismentalling of existing structures like bridges, culvert, retaining wall and other structures comprising of masonry, cement concrete, wood work, steel work including T&P and scaffolding wherever necessary sorting the dismentalled materials , disposal of unservicable materials and stacking the servicable material with all lifts and leads of 1000m as per technical specificatiopn clause 202 (C) Reinforced Cement concrete

Granular sub base with well graded material (CBR 20 or more)(Table400.1) (a) Construction of granular sub base by providing well graded material having CBR 20 or more spreading in uniform layers with motor grader on prepared surface mixing by mix in place method by rotavator at OMC and compacting with vibratory roller of 80 to 100 KN static weight to achieve the desired density complete as per technical specification clause 401. For Grading Mention in table 400.1 (Grading III)

Wet mix macadam Providing laying spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in m achenical mixture (Plug mills) carries of mix material by tipper to site laying in uniform layers in sub base / base course on a well prepared subbase and compacting with smooth wheel roller of 80-100 KN weight t achieve the desired density including lighting, barricading and maintenance of divesion etc as per table 400.11 and 400.12 and technical specification clause 406

Cement Concrete Cell Fill Pavement Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Cutting of branches of trees shrubs and trimming of grass and weeds Trimming of grass and weeds from the shoulders/berms and disposing off the same to suitable locations as per technical specifications Clause 1914

Restoration of rain cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh material in layers not exceeding 250 mm and compaction with plate compactor or power rammer to restore the original.

Scarifying Existing Granular bituminous Surface to a Depth of 100 mmScarifying existing granular/bituminous surface upto a depth of 100 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

Maintenance of WBM road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and raveling as per technical specification Clause 1906.

Prime Coat Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Maintenace of bituminous surface road Repair to pot holes and removal of loose material, trimming of sides, cleaning of surface by providing tack coat, 20 mm thick pre-mix carpet and seal coat type B specification Clause 1904.2

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Bituminous macadam Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per table 500.4. Premixed with bituminous binder, transported to sitee laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to acchive the desired compaction as per technical specification clause 504 Bituminous S-65 (VG-30)

20mm thick Open-Graded Premix Carpet using Bituminous (VG/modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of aggregate 13.2mm size (passing 22.4mm size sieve & retained on 11.2mm sieve and 11.2mm size (passing 13.2mm sieve and retained on 5.6mm sieve) either using penetration grade/ VG bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508., Viscocity grade (VG) Bitumen specification as per IS 73:2006

Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510, Viscocity grade (VG) Bitumen specification as per IS 73:2006 Case - II : Type B (ii) (VG-30)

Construction of subgrade and earthen shoulders with approved material (granular material having CBR not less than 7 ) obtained from borrow pits with all lifts and leads transporting to site spreading grading to required slope and compacted to meet requirement of table 300.2 as per technical specification clause 303.1 for item No. 3.12 (a)&(b).

Road marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC: 35. The finished surface to be level, uniform and free from streaks and holes.)