REPAIRS TO ROOF, JOINERY, FLOORING, PLUMBING, TILLING, PLASTERING, CEILING, SANITARY FITTING AND ALLIED INFRA, MD ACCN AT ALBERT EKKA, JIB, CHHETRI COMPLEX UNDER AGE BR-I,GE (SOUTH) UDHAMPUR

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoines arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar beddig not backing complete all as specified and directed.

Providing 50 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

Providing 50 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in floor/sub-base and finished even and smooth without using extra cement complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as, copings, benching and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Form work to soffit of suspended slabs such as roof slab floor slab landing and similar work not exceeding 200 mm thick surface horizontal or sloping rough finished surface of concrete complete all as specified and directed.

Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild Steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and directed.

Random rubble masonry built in cement mortar 1:6, uncoursed, well bonded, bedded and solidly hearted complete all as specified and directed.

All as per ser item No 13 hereinbeore above but except stones complete all as specified and directed.

10 mm thick rendering on ceiling in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and directed.

15 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

15 mm thick rendering in two layer (10 mm + 5 mm) on fair faces of brick/concrete/ stone surfaces including facia chhajja etc.surfaces in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and directed.

15 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 and finished even and fair to receive tiles without using extra cement complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor and finished even and fair complete all as specified and directed.

Non-skid coloured ceramic tiles (square/ rectengular) 7 to 8 mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Glazed ceramic coloured tiles in vertical surfacaes 300 x 450 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface as approved and complete all as specified and directed by GE.

Granite slab 16 to 18 mm thick as in pillars, window cill, cooking platform and the like in cement mortar 1:4 including painting in white cement 1:2 using marble dust with a mixture of pigment to match the shade of granite including cutting polishing and moulding on edges complete all as specified and directed.

Pre glazed cloured chequered cement concrete tiles 300 mm x 300 mm x 20 mm thick, machine pressed; set, jointed and pointed in neat cement slurry, with grey cement and pigment in floors complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated) etc sheets in roof covering including ridges complete all as specified and directed.

Dismantling wall and ceiling boards, fibre pulp insulation etc) or insulation boards/ slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

AC designer composite ceiling board 4 to 6 mm thick in 600 x 600 mm panel confirming to IS-14682 type-B category-3 including GI frame, holdfast & suspenders complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates confirming to grade Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

6 mm thick asbestos cement corrugated or semi corrugated sheets in roof, walls etc. fixed with 'L' type or 'J' type hooks or cranked hook bolts complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each including cutting holes for taking out hold fasts, dismantaling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each including cutting holes for taking out hold fasts, dismantaling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified and directed.

Taking down shutters of any description exceeding 1 square metre not exceeding 2 square metre each complete all as specified and directed.

Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube and fixed in opening as per specification and drawing complete all as specified and directed.

Factory made solid panel PVC Moulded door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing. Clause No. 8.B.1 to 8.B.10 and drawing on page No 156 and 157 of MES SSR-2010 Part-II complete all as specified and directed.

35 mm thick factory made, 2nd class hard wood , plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

Mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290.Gde-E-165 complete all as specified and directed.

Steel window (Box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified. Note : (i) The window shall be fabricated as per Drg CEUZ/TD/1269/2008 Sh 1/3. (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

All as per ser item No 39 here in before but without glazing bar complete all as specified and directed.

Mild steel ventilators (Box type) factory made with top hung shutters and bottom fixed type shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg CEUZ/TD/1269/2008 Sh 1/3. (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt complete all as specified and directed.

Aluminium alloy, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Aluminum handles cast type, anodised, 150 mm size complete all as specified and directed.

Mild steel, 300 mm, ordinary rat tail rod pattern door spring including roller and roller plate, fixed to frame complete all as specified and directed.

Pressed steel frames for doors made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, 12 mm bar thresh hold etc. complete, of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

Pressed steel frames for doors made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, 12 mm bar thresh hold etc. complete, of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

Door closer hydroulically regulated desigination No-3 universal type alm extruded section body complete all as specified and directed.

Hacking out old broken glass panes (any thickness, size quality or description) from wooden frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

5 mm thick Figured glass pin headed type and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Drapery rod of 25 mm dia powder coated decorative along with brackets and end caps of quality as approved and complete all as specified and directed by GE.

18/19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Block boards grade 1 quality exterior grade commercial type fixed with screws to timber frame work 25 mm thick including decorative laminate type 1 of surface finish colour and pattern as approved with adhesive 1.5 mm thick complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finishor electrogalvanised width of flaps (when open) 30 mm complete all as specified and directed.

100 mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

10 ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed. Make : CERA/Prayag/Parryware

Supply only flush pipe of polyethylene of low or high density or PVC, 32 mm dia, for low level cistern complete all as specified and directed.

Brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed with 15 mm bore pipe complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to storeyard complete of bore 15 mm complete all as specified and directed.

All as per ser item No 64 hereinbefore but 20 mm bore pipe complete all as specified and directed.

Refixing 15 mm dia old steel tubing and connecting in new or old position (Walls, ceiling, floors etc and making good, cutting not exceeding 10 cm girth) complete all as specified and directed.

Refixing 20 mm dia old steel tubing and connecting in new or old position (Walls, ceiling, floors etc and making good, cutting not exceeding 10 cm girth) complete all as specified and directed.

Steel water tubing of nominal bore 15 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and directed.

All as per ser item No 68 hereinbefore but 20 mm bore pipe complete all as specified and directed.

Demolition and breaking up drain pipes 100 mm dia (Salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

PVC (SWR) pipe single socketed in any length with rubber rings joints fixed to walls for 110 mm bore pipe complete all as specified and directed.

110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

Vitreous China wash basin, white, flat back, size 550 mm x 400 mm excluding tap, chain, plug and porcelain stopper but including brackets and cutting for and pinning in ends of brackets complete all as specified and directed. Make : CERA, Cat Part No - 1025, 1108

Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed. Make : Nirali

Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

Vitreous China wash down water closet pan (pedestal pattern anglo indian type), white (excluding fixing bolts, flushing cistern and flush pipe) with P or S trap but including plastic water closet seal, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device including connection to drain and flush pipe complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including a provision of concrete bedding complete all as specified and directed. Make : Cera/Hindware/Johnson

Dismantling water tanks capacity in exceeding 250 and not exceeding 500 ltrs complete all as specified and directed.

All as per ser item No 78 hereinbefore but exceeding 500 ltrs and not exceeding 1000 ltrs capacity complete all as specified and directed.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories complete all as specifed and directed.

All as per ser item No 80 hereinbefore above but 1000 ltrs capacity complete all as specified and directed.

PVC grating 100 mm dia fixed to floor trap in repair complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plate bracket guard and railing 60 cm long in repair complete all as specified and directed.

Bib taps 15 mm bore, fancy type, cast copper alloy chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Waste fittings 32 mm/40 mm bore, brass, chromium plated for basins etc with long screwed shanks and fly nuts, flange and bed deal in red lead cement and other end as in repair complete all as specified and directed.

PVC connection 15 mm size with PTMT (Make-Prayag) Nuts of length 450 mm complete all as specified and directed.

PVC tank lid for 1000 to 2000 litre capacity including all locking arrangements, nuts, bolts etc for fixing complete all as specified and directed by Engr-in-Charge.

GI Nipple 20 mm suitable for HDPE water tank complete all as specified and directed.

Ball valves of size 15 mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 142 gms) screwed for iron pipe and fixed including necessary fitting as required at site complete all as specified and directed by Engr-in-Charge.

Ball valves of size 20 mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as required at site complete all as specified and directed by Engr-in-Charge.

Brass ball valves of size 20 mm bore dia high pressure of with polyetylene floatand flynut screwed for iron pipe and fixed including necessary fitting as required at site complete all as specified and directed by Engr-in-Charge.

Stop valves/angle valve cast copper alloy 15 mm, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions including necessary fitting as required at site complete all as specified and directed by Engr-in-Charge.

Roughening of old concrete surfaces by picking, sweeping clean and washing down with water, fanning dust etc and taking down tarfelt and brushing neat cement slurry with 3.00 kilogram of cement per square metre including 20 mm thick screed bed or bedding layer in cement mortar 1:4 finished even and smooth including mixing with integral WPC complete all as specified and directed. Note : Supply only water proofing compound shall be measured and paid separately under the respective Item.

Priming the roof surface with bitumenous primer @ 0.4 litres/Sqm and applying a coat of semi hot blown 85/25 grade bitumen @ 1.2 Kg/Sqm and thereafter supply and laying Polymeric membrane 3.00 mm, five layered of weight not less than 3.50 Kg per Sqm with centre layer core of 90 micron high molecular density polyethylene film and bonded completely to the surface with overlap of 10 cm (overlap to be thermo fused by frame) followed by another coat of semi hot blown 85/25 grade bitumen @ 0.7 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm and applying a coat of aluminium paint complete all as specified and directed. Note :- Water proofing treatment will be done by IWL or through a specialized agency which will further have to give a five years warranty for rectification of any defect if incurred at a later stage, otherwise no payment shall be made to the contractor if water proofing treatment is executed by engaging local labour.

Preparation of old steel and iron surfaces of any discription exceeding 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of new steel and iron surfaces of any discription exceeding 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed.

Preparation of new wood or wood based surfaces of any discription not otherwise described exceeding 10 cms width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparation of old painted wood or wood based surfaces exceeding 10 cms width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coat of oil emulsion distemper over one coat of primer complete all as specified and directed.

Preparation of surfaces and applying two coats of white wash on newly plaster surfacescomplete all as specified and directed.

Preparation of surfaces and applying two coats of white wash on ceiling on newly plaster surfaces complete all as specified and directed.

Preparation of newly plaster surfaces and applying two coats of cement base paint on walls complete all as specified and directed.

Preparation of new/old surface as on walls and applying two coat of wheather proof emulsion over a coat of primer complete all as specified and directed.

Preparation of new and old surfaces on wall and applying a coat of wall putty (JK/Birla) to make the surface smooth and even complete all as specified and directed.

Pre painted galvalume aluminium zinc coating GI based corrugated sheets 0.60 mm thick of any colour having tensile strenght of 550/MPA as in roof covering, cladding to wall fixed with self taping screws complete all as specified and directed.

All as per ser item No 105 hereinbefore above but plain sheets as in ridges complete all as specified and directed.

Supply only (LW+) water proofing liquid solution of Dr fix it/sikka or equivalent make complete all as specified and directed.

M/S ASHOK KUMAR PACHIALA

vijay constrction co

SODHI TRADING CORPORATION

RAMAN CONSTRUCTION CO

ashok kumar