Development of ICE Skating cum Roller Skating Rink at SHIMLA (HP).

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. -- All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth at approved dumping site by mechanically & manual upto all lead & lift and as per direction of Engineer incharge dumping site/disposel site shall be arranged by the contractor at own cost and nothing shall be paid extra -- Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil at approved dumping site by mechanically & manual upto all lead & lift and as per direction of Engineer incharge dumping site/disposel site shall be arranged by the contractor at own cost and nothing shall be paid extra.All kinds of soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils at approved dumping site by mechanically & manual upto all lead & lift and as per direction of Engineer incharge dumping site/disposel site shall be arranged by the contractor at own cost and nothing shall be paid extra. -- Ordinary rock

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : --- (a) 1:2:4 (1 Cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : --- (a) 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20mm nominal size) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Retaining walls in plum concrete with front of hardstone and rest in cement concrete mix in 1:4:8 (1 cement:4 sand :8 aggregate 25mm nominal size with stone plums at regular intervals as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Boulder filling dry hand packed behind Retaining wall complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. --- (a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : ---- (a) Cement mortar 1:6 (1 cement : 6 coarse sand) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. --- (a) Cement mortar 1:4 (1 cement :4 coarse sand) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.. (The payment of RCC band and reinforcement shall be made for seperately).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : --- (a) Cement mortar 1:6 (1 cement : 6 coarse sand) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying 20 cm. Thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6(1 cement :6 sand) and concrete backing with cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stone aggregate 20 mm. nominal size) on inner face of walls including centring,shuttering and propping complete up to floor two level as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make like KAJARIA,NEXON,NITCO,STANZA of size 600 x 300 mm , in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make like KAJARIA,NEXON,NITCO,STANZA, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. -- Size of Tile 1000x1000 mm

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : -- Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying hard stone pavers blocks size assorted sizes minimum100x200x75 mm over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete including carriage of materials with in all lead and lifts.(Sub base concrete floor to be paid for separately) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing flooring of local stone 37 mm to 50 mm thick laid down as per pattern by the Architect as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.. 1.20 m width over plinth protection with 20 mm thick cement mortar (1:4) including skirting of minimum 230 mm wide.

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Prov. & Fixing 10 mm thick Unistone/durostone cladding Tiles with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement Complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions consisting of: Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofingcompound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg.per sqm of area. IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be easured from top of shoe to the bottom of pile cap) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : -- 750 mm dia piles

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. --- (a) Second class teak wood

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. --- (a) Sal wood

Providing and fixing ornamental wooden facia/ carving of 1st class deodar wood of section size 230 x 450 mm including fixing in position complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing 9 mm ply under ceiling with necessary screws/nuts & bolts/ nails fixed on wooden /steel frame work, complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.(Frame work shall be paid for separately).

Providing and fixing 12 mm thick readymade Pine wood planks in ceiling with tongued and grooved jointing and screws .(frame work and cover fillets to be easured and paid for separately) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing plain lining with tongued and groved jointing and screws including beading (frame work and cover fillets to be measured and paid for separately with. - 1st class 6 mm teak ply of approved shade over 12 mm water proof commercial ply Complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.--- (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. :- 2nd class teak wood - 50x12 mm

Providing and laying 8 mm thick pergo extra ac - 5 authentic oak class 32 as per EN 13329 in flooring , profiles & skirting including foam density 35+/- 5 kg cubic meter under flooring used as a moisture and sound barrier, the panels having a click system tongue and groove joint with the edges duly impregnated with paraffin complete as per the directions of the manufactureres specifications as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing cup board by using 19 mm water proofing board of approved manufacture for shutters, vertical and horizontal partitions (teak board) etc. and fixing 6 mm thick water proof ply backing, internal finished with 4mm thick mica sheet of approved colour and make, 2nd class deodar wood edge beading, moulding including painting/polishing on edge beading and moulding, brass handles, cachers M.S. piano hinges & Godrej lock etc. complete as per Architectural/sketch drawings and as per the direction of the Engineer-in-Charge including carriage of materials in all leads and lifts (Greenply/Kitply).

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing ISI marked oxidised Stainless steel heavy duty Sliding door bolts with nuts and screws etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : -

Providing and fixing tower bolts, ISI marked, Stainless steel heavy duty with necessary screws etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. :

Providing and fixing handles, ISI marked, Stainless steel heavy duty with necessary screws etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. :

Providing and fixing Keyless mortice door locks on toilet doors of godrej or equivalent 100 mm with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing bright finished ISI marked, Stainless steel heavy duty hooks and eyes as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : 300 mm

Providing and fixing ISI marked, Stainless steel heavey duty hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. --- (a) Twin rubber stopper

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) - - Fenista make

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.. (Single / double glass panes and silicon sealent shall be paid separately). NOTE :- For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with self drilling screws with washers etc. complete with all accesoriees as required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with self drilling screws with washers etc. complete with all accessories as required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with self drilling screws complete with all accessories as required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing 15 cm. wide 45 cm. overall semi circular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. - 0.63 mm thick sheet

Providing and fixing button / remote operated Retractable sliding Roof of NIHVA make of Aluminium Alloy Profiles, Stainless Steel Fasteners and Poly carbonate Sheet Fillings including doors, Locking systems, Rubber seals, etc. complete as per manufacturar's specifications as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. -- In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

15 mm cement plaster on the rough side of single or half brick wall of mix as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : ---- (a) 1:6 (1 cement: 6 fine sand)

Polishing two coats with lacquer polish on wood and wood based surfaces to give an even surface including cleaning the surface of all dirt , dust and sand papered smooth and including a coat of wood filler as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : --- (a) Two or more coats on new steel work over an under coat of suitable steel primer of approved brand and manufacture.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : --- (a) Two or more coats on new wood work over an under coat of suitable wood primer of approved brand and manufacture.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. --- Two Coats

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : - Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : - With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DISMANTLING AND DEMOLISHING - Demolishing cement concrete manually/ by mechanical means including disposal of material as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. -- Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. -- In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : Of area beyond 3 sq. metres

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : - Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : - Of area beyond 3 sq. metres

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.f: - G.S. Sheet

Dismantling tile work in floors and roofs laid in cement mortar including stacking material as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. : - In cement mortar

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming toAISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875-1987, ISO 800-1984 and IS:801- 1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7 / STAAD PRO-V8i / Architek V 2.5.16 / Revit architecture -2011 or equivalent. Proper usage of ConnectionAccessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

requirement duly punched with dimple / slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping screws for joining the members shall have a Type II coating in accordance withASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm.

The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming toAISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above.

Providing and fixing internal wall panels on Light gauge steel frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on 8mm thick fiber cement board conforming to IS 14862:2000 of category III type B (High pressure steam cured) as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of semi unitised glazing system with 6 mm AIS essence plus tempered + 20 mm Aegon gas and Cappillary tube + 8 mm tempered having VLT -71% , SF -53, SC-61 & U value 1.8 kg/watt degree Kelvin Hermetically sealed IGU System And having section 76x75 mm visible Curtain wall section & required subframe with EPDM gaskets. Silicone is to be used high performance all weather 789 grade Dow Corning with accessories. as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Dehumidifier, Industrial Desiccant Dehumidifier with in built Air Handling unit AMS model 10000 CFM capacity made up with desiccant rotor, process motor, & blower, reactivation motor& blower, reactivation heaters, steam coil, gear reduction unit, filter, electric control panel , extruded all frame with powdre coated thermal break, PP corner, G.I powder coated panels 24/ 24 swg., ss sheet with puf insulated panels, ss drain pan, cooling coil. micro filter, after filter,final filter, PP handles,with hinges , inspection door. sticking type leak proof gasket, anti vibration mounting pads, internal cabling vibration canvass, metal alloy alien bolts with nutserts for panel fixing, door interlock for blower and base frame as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing PUF insulated continuous sand wich panel roofing of total thickness 10 to 20mm and width 1.0 , made out from continue line method on automatic plant. Panel shall have pre coated G.I. sheet on both side of polyurethane foam confirming to IS 12436:1988. The precoated sheet shall be of minimum 240 mpa steel grade confirming IS 14246:1995 and shall have zinc coating of minimum 120 gsm as per IS 277: 1992, 5-7 microns epoxy primer on both side of the site and polyster top coat 15-18 micron. The PPGI sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. The panel shall be vertically joint together by tongue and groove joints. the PU foam shall be self extinguishing, fire retardant type having minimum density of 40 KG /cu.mt(+,-2 Kgs) including 0.25 mm thick craft paper edging on both edges. The panel shall be fixed to the steel frame structure with minimum 5mm thick self tapping GI screws of required length and nos. with minimum spacing of 300mm c/c complete in all respect PPGI sheet 0.5 mm thick skin on both sides as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

WATER SUPPLY AND SANITARY INSTALLATION- Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

75 mm nominal inner dia Pipes

100 mm nominal inner dia Pipes

150 mm nominal inner dia Pipes

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

4050 (50 mm OD) pipe

Providing and fixing 110 mm X 4 Kgf pvc Poly plast sewarage pipe of working pressure not less than 4.5 kg per sqcm (Four point five kilogramme per sqcm) including filling the joints with approved adhesive complete including carriage of material as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. -- 110mm dia pipes

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. -- 110 mm diametre

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Coupler -- 110 mm

Single tee with door -- 110x110x110 mm

Bend 87.5° -- 110 mm bend

Shoe (Plain) -- 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised PVC pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Sintex or equivalent.

Providing and fixing viterous china water closet Jaguar make Cat No. RS-WHT-37953BIUFSM incld. Concealed cisterncat. No. JCS- WHT-2400NS and cover plate JCP-CHR- 392415 including all fittings and accessories, Hindware /Cera make or equivelent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing viterous china water closet Jaguar make ARS-WHT-39953BIUFSM single piece wc with pp soft close seat cover, hinges, fixing accessories set and cistern fittings size 360x640x685 mm including all fittings and accessories, Hindware /Cera make or equivelent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing counter top vitreous china wash basin Jaguar make Cat No.DRS - WHT- 37601 including c.p. waste and waste pipe complete set Hindware /Cera make or equivelent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing white vitreous china URS-WHT-13253N Urinal (Back Inlet) With Fixing Accessories, Size: 385x325x635 mm Jaquar make, FLV-1093NSQ, Metropole Flush Valve Regular, 40mm Size (Concealed Body) with Exposed Shut Off Provision &, 100mm Square Plate or equivalent make with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Urinal Partitions, JSE-CHR-110UC450X, H: 900 W: 450 jaquar make or equivalent including all charges for cost, carriage,and labour for fixing and making the wall good as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing NIRALI make stainless steel kitchen sink of size 1040 x 545 (Opal) including cutting and making good thw walls wherever required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing 32mm dia PVC pipe for wash basin as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Click Clack Waste 32mm Size Half Thread With 80mm Height - ALD-709 including Bottle Trap 32mm Size with 250mm & 190mm Long Wall Connection Pipes & Wall Flange ALD-769L250x190 as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. 32mm dia

Providing and fixing 125 mm stainless steel square grating of approved brand including cutting and making good the walls wherever required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing bevelled edge miror of superior glass Saint Govind/Modi guard or TATA make with C.P. set of stud and brass screws and washers as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing & fixing C.P. Towel ring Jaguar make Cat No. AKP-35721P or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing C.P. Towel rack with lower hanger Jaguar make AKP-35781 PS or equivelent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing ACN-1111SM Single Towel Rail 600mm Long, Stainless Steel Jaquar make or equivalent including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Bib cock (strainght line model) with wall flenge Jaguar make Cat No. FLR-5047N or equivalent with all accessaries including cutting and making good the walls wherever required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing C.P. pillar cock with base flenge Jaguar make Cat No. KUP35001PM or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Faucet Range FON-40053 angular stop cock with wall flange, Jaguar make or equivalent with all accessories including cutting and making good the walls wherever required as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Aqua Max Wall mixer OPP-15683KPM Single Lever Exposed Parts Kit of Hi-flow Diverter Consisting of Operating Lever, Cartridge Sleeve, Wall Flange (with Seals), Button Assembly Sleeve & Button Jaquar Make with ALD-683 Aquamax Concealed Body of Thermostatic Shower Mixer with 3-way diverter, But without Exposed Parts, overhead shower OHS-1619 200x200mm, hand shower jaquar make Maze Hand Shower 95X95mm, Square Shape Single Flow, (Face Plate Stainless Steel, & ABS Body) with Rubit Cleaning System and 15mm NRV for shower system, SPJ-15463PM Bathtub Spout with Button Attachment for Hand Shower with Wall Flange, Aquamax Concealed Body of Thermostatic Shower Mixer with 3-way diverter HSH-1717 of Jaguar make or equivelent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Thermostatic mixer no. ARC-87681 K Aquaman Exposed part kit of Thermostatic Shower Mixer with concealed body of Mixer no. ALD- 661, with spout no. OHS - 35495 , overhead shower 150x150 square with Rubit cleaning system and shower arm dia 20mm & 600 mm long round shape with 90 deg. bend for wall mounted shower with flange no. SHA-479L600 and spout no. SPJ-81429 spout with wall flange as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing & fixing shower mixer exposed part jagaur ORP-10681KPM and concealed body of single lever shower mixer ALD - 681 and shower no OHS - 1629 with shower arm 45 cm, and spout SPJ-10429 PM of Jaguar make or equivelent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing KITCHEN FAUCET ORP-10173BPM Single Lever Sink Mixer with Swinging Spout (Table Mounted) with 450mmm Long Braided Hoses, jaquar make or equivalent in with all accessories including cutting and making good the walls wherever require including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing FAUCET RANGE OPP-15011BPM Single Lever Basin Mixer without Popup waste with 450mm Long Braided Hoses, jaquar make or equivalent in with all accessories including cutting and making good the walls wherever require including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing & Fixing hand shower (health faucet) Jaguar make Cat No. ALD-573 with 8 mm dia, 1.2 m long flexible tube & wall hook or equivelent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing shower basket large ACN-1179 N of Jaguar or equivalent including cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing corner shower basket ACN -1175 N of Jaguar or equivalent including cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Paper towel dispenser with c/z folds wall mounted no. PTD-SAP-DT0106CS capacity 400 to 600 c/z towels material SISI 304 stainless steel finish satin as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing HDR-SSF-AK2803D Bolt touch-free infrared hand dryer with 1150W rated power & carbon stainless finish satin of Jaguar make including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Essco Jaquar Brass Jet Spray Nozzle (Chrome) with 1 Meter PVC Tube essco, Jaquar make or equivalent including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing ACN-1131N, Soap Dish Holder, jaquar Make or equivalent including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing ACN-1137N, Soap Dispenser with Metallic Bottle, jaquar make or equivalent including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing ACN-1153S, Toilet Roll Holder with Stainless Steel, Flap jaquar make or equivalent including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Double Coat Hook Jaquar make Cat No. AQN-7761 or equivalent including cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing DIS-WHT-93753P180UF Rimless Bowl For Coupled WC with UF Soft Close Seat Cover, Hinges, Fixing Accessories, Size:390x610x800mm, P Trap- 180 mm, jaquar make and DIS-WHT-93201Cistern with Dual Flush Cistern Fitting for WC seat of Jaquar make or equivalent including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts. - For Specially Abled

Providing and fixing Wall Hung WC with UF Soft Close Seat Cover, Hinges, Accessories Set, Size : 350x750x340 mm cat. No. DIS-WHT-93951UF including Single Piece Slim Concealed Cistern Body with Installations Kit & “S-Type” drain pipe connection set for Wall Hung WC (without Flush Control Plate) cat.-No. JCS-WHT-2400S and Control Plate D’arc cat No. - JCP-CHR-372415 including painting of fittings and brackets, cutting and making good the walls wherever require including all cost, conveyance and labour charges etc complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Grab bar-Vertical Swing-Satin Jaquar make Cat no. WAC-SAP-BG0800CS wall mounted or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

REFRIGERATION WORK- Designing, Supplying, installation, testing and commissioning of following ice skating items with Operation and Maintenance for Five Years including MEP design, consultation services, CAD drawings, equipment specification and site instructional data to assist site architect and site engineer complete in all respect. It includes mandatory site visit every two months after first installation of the ice skating rink equipment including professional training to personnel for the operation and maintenance of the ice skating rink equipment and mandatory site visit at the commencement and end of every season. The rates shall include all import duties, and taxes as applicable including transporation complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of Propylene Glycol with not less than specification of water ,wt% : 4.0 MAX, Test Method: D-1123, specific gravity, 60/60F: 1.05 MIN.-1.06 MAX., Test method: D-1122, reserve alkanity ml: 10.5 MIN.-14.0 MAX, Test Method: D-1121, ph, 33% solution: 9.5 MIN. - 10.5 MAX Test method: D-1287, freezing point 50% vol, F,C: -30 (34), Test Method: D-1177, SITC of Ice rink divider, 30x30x30 cm, length 5 m with not less than following specifications Colour: Blue Prism shaped elements filled with plastic foam; Velcro fastener and carrying straps included. Easy to install. The ice rink can be divided in different topics (e.g. Eisstock, skating, ...). Colour: Blue Sioen B6000 5003 Weight: 18 kg, SITC of Circle for the setting of Marking Strips with not less than following specifications A circle device to roll out 5 cm wide ice hockey marking strips. The circle device is made of a high-grade steel construction with an integrated water tank. The device is fitted with a brake, in order that the marking strip stays tight when being rolled. A sponge - behind a guide pully - wets the lines, which then directly freeze. With the delivered radius bar, the circle markings of 4500 mm and 1800 mm can easily, cleanly and quickly be produced. SITC of Ice Expert Set Basic Equipment not less than following specifications The basic equipment for the ice rink expert in a rugged plastic box consisting of: -Measuring laser for ice thickness measurement in its own case -Universal retainer for laser -Measuring stick -Universal spray nozzle (spray or hard stream) -20 meter hose 1" with Geka-connection sockets -Repair set for ice mats in plastic case -Ice-maintenance instruction manual, SITC of ICE Colour Powder, white, 27.5 kilos not less than following specifications for the colouring of ice surfaces. A white ice surface reflects lighted ice, which then requires less freezing and lighting energy. The contents of one package - mixed with 250 litters of water - is sufficient to cover ice surfaces of 150 m² at triple coats. SITC of Rubber Surface: Skate Proof, Skate resistant rubber surfacing made from high grade vulcanized not less than following specifications and new rubber 1 cm thick. Colour: black,Durability: approx. 65 Shore A,Surface: Grip 1 mm,Bottom Side: smooth,Weight: 11.7 kg/ Unit i.e. 13.0 kg m2, Connection: sturdy puzzle connection, SITC of Marking set for ice hockey rinks for 2 fields marking set for ice hockey rinks for 2 fields made of disposable material excellent noticeability on ice due to eye-catching colours Easy and quick laying not less than following specifications, Ice hockey goal area marking according to the IIHF rules 2018, light-blue surrounded with red line. Digital print ready for use, reusable 244x183 cm, Logo printed on mesh for centre circle

ICE Colour Powder, white, 27.5 kilos for the colouring of ice surfaces. A white ice surface reflects lighted ice, which then requires less freezing and lighting energy. The contents of one package - mixed with 250 litters of water - is sufficient to cover ice surfaces of 150 m² at triple coats. Supply, Installation, Testing and Commissioning of ONE Scoreboard Black Box, Supply, Installation, Testing and Commissioning of Goal lights,Supply, Installation, Testing and Commissioning of External Start/Stop Controller,Supply, Installation, Testing and Commissioning of External 4 Button Controller,Supply, Installation, Testing and Commissioning of TWO TONE HORN (power 112 dB / 130 dB),Supply, Installation, Testing and Commissioning of Splitter for 4 monitors, Supply, Installation, Testing and Commissioning of Cooling surface of Ice Hockey Rink of area appx 30m x 60m with absorber mats / refrigerant piping system of EPDM 120/6 including headers & collectors at long side all complete as per manufactures specification and methodology. Supply, Installation, Testing and Commissioning of Fully Insulated collector pipes (approx. 32mm), with especially produced manifolds made of PE for connecting the refrigerant piping system/Ice mats with all connecting sleeves, etc. Insulation of the pipes shall be with closed-cell rubber material (32mm). The collector pipes shall be installed on steel-consoles or on steel pipe supports in the collector channel. Supply, Installation, Testing and Commissioning of Monoethylene glycol pure mixed with water in the ratio 40:60 shall be filled in pipes as refrigerant.Supply, Installation, Testing and Commissioning of HDPE connection piping DA180 insulated 32mm Inlet and outlet piping insulated with closed-cell rubber material, 32 mm, including all fittings and connection pieces.Supply, Installation, Testing and Commissioning of Expansion tank 1800 L insulated with steel-frame and bypass-piping galvanized steel-tank with cover on a steel-frame, isolated with closed-cell rubber material, 32 mm. Bypass-piping with armatures for optional operation for an open or closed system. Expansion tank: LxBxH: 2.200 x 1.000 x 1.200m height from the frame: 1.400m, Providing & laying of XPS insulation of 50 mm under the base layer (concrete/sand) of the ice mats. (approx. 3700 sqm), Providing & laying of 100 mm for thickness of cement concrete mixed with integral water proofing compound and 75 mm thick PCC below and providing sand base as per site requirements. (1800 sqm), SUPPLY & INSTALLATION OF ANTI-SKID / SLIP RESISTANT / SPIKE RESISTANT/CUSHIONED / SOUND ABSORBENT INTERLOCKING RUBBER MATTS IN THE WALK AREA OF THE PLAYERS OUTSIDE THE RINK AREA.(approx. 400 sq m.)

Ice Hockey Dasher boards - pro series Supply, Installation, Testing and Commissioning of one ice surfacer gate, Supply, Installation, Testing and Commissioning of three access gates,Supply, Installation, Testing and Commissioning of standard board frames sizes,Supply, Installation, Testing and Commissioning of player boxes, penalty boxes and scorer box,Supply, Installation, Testing and Commissioning of all stainless hardware ( e.g. fasteners, hinges, latches, locks etc.),Supply, Installation, Testing and Commissioning of stainless frames for dasherboards for a life time service, materials:- Supply, Installation, Testing and Commissioning of stainless rectangular frames not less than: 4"x 2" @ 2 mm thick , Supply, Installation, Testing and Commissioning of Cladding not less than: 10 mm clear poly carbonate facing,Supply, Installation, Testing and Commissioning of Caprail not less than: 1/2blue high density polyethylene,Supply, Installation, Testing and Commissioning of fasteners not less than: stainless bolt with cap nut on both ends,Supply, Installation, Testing and Commissioning of hinges and locks not less than : all polished stainless 304 ,Supply, Installation, Testing and Commissioning of anchors not less than: (for perimeter board panels) Zinc plated steel.Supply, Installation, Testing and Commissioning of spectators sheilding not less than : high tempered glass ,Supply, Installation, Testing and Commissioning of spectators sheilding support not less than : ASTM B221,60OS - TS Alloy and temper ,Supply, Installation, Testing and Commissioning of fabrication not less than: custom design as per site requirements. board panels -Supply, Installation, Testing and Commissioning of Typical size not less than: 96" long by 42" high,Supply, Installation, Testing and Commissioning of anchors not less than : two 1/2" diameter anchor bolts.Glass shielding -Supply, Installation, Testing and Commissioning of Spectator shielding shall be high tempered glass ,Supply, Installation, Testing and Commissioning of 6 ft , 3/4 " thick tempered glasssheilding for the ends and radius corners of the rink complete with two piece anodized aluminium sheild supports.Supply, Installation, Testing and Commissioning of Glass sheild supports will be within 6" of the top of glass .Gates-Supply, Installation, Testing and Commissioning of Access gastes are 3 ft. wide and are built into an 8 ft board panel, with a choice of left or right swing. The gate latch will be equipped with a counter balanced mechanism so that the gate may be closed and latched in a single movement.Supply, Installation, Testing and Commissioning of resurfacer gate is a double leave of 5 ft each, with a 10 ft total width. Each equipoment gate unit is equipped with one locking clamp and two retactable locking pins.Supply, Installation, Testing and Commissioning of Each equipment gate is equipped with adjustable heavy duty swivel caster and adjustable tie rod assemblies ,Supply, Installation, Testing and Commissioning of Player gates are 3 ft wide with heavy duty stainless hinges and lift latches. All gate hinge assemblies are conbstructed of stainless steel. The hinge pins are heavy pins are heavy duty. 1" thick HDPE (high density polythylene) thresholds on equipment , player, and access gates.

Boxes- Player boxes -Supply, Installation, Testing and Commissioning of Two 40 ft (12000 mm) long and 5 ft (1500 mm) deep two player gates on the ice side for each player box.Penalty Boxes -Supply, Installation, Testing and Commissioning of two 16 ft (4800 mm ) long and 5 ft (1500 mm ) deep one access gate for each penalty box. Time keeper box - Supply, Installation, Testing and Commissioning of 16 ft (4800mm ) long and 5 ft (1500mm) deep with long side divider panels

Engine room - Supply, Installation, Testing and Commissioning of Glycol Expansion Tank not less than: Stainless, 3 mm thick, 1 metre diameter, 1.73 m meter high .Supply, Installation, Testing and Commissioning of Skid not less than: 6" Steel C channel,2.88meterx 2.82 m, Top Cladded with 3 mm Checkered plate.Supply, Installation, Testing and Commissioning of Pump not less than: 2 units, close coupled centrifugal,120ft. TDH, 800 gallons per minute.Electrical supply: as per site requirements.Supply, Installation, Testing and Commissioning of Y- strainer not less than: ASTM 6".Supply, Installation, Testing and Commissioning of Isolation valves not less than: ASTM 6".Supply, Installation, Testing and Commissioning of Check Vave not less than : ASTM 6 ".Supply, Installation, Testing and Commissioning of Byepass Valve not less than: ASTM 3" .Supply, Installation, Testing and Commissioning of Air Seperation not less than : ASTM 1/2 " Ball Valve.Supply, Installation, Testing and Commissioning of Glycol Charging port not less than: 1" Ball Valve.Supply, Installation, Testing and Commissioning of Level Detector not less than: 1/2" glass tube with brass fittings.Supply, Installation, Testing and Commissioning of Electrical Box .: Double Door, IP 55.Supply, Installation, Testing and Commissioning of Control : Variable frequency Drive and Direct on line.Supply, Installation, Testing and Commissioning of Insulation not less than : 2" rubber insulation for the Glycol Expansion Tank and piping.Supply, Installation, Testing and Commissioning of Cladding : Aluminium cladding for Glycol expansion tank and piping.Supply, Installation, Testing and Commissioning of paint : Custom color.Portable Ice Rink Refrigeration Pipe Grid-Supply, Installation, Testing and Commissioning of material not less than following specifications : Virgin high density polyethylene elongation : 395% ,operating temperature : -40 C to 65.6 C ,Durometer :-(Shore A) ,94,Tensile Strength : 4,298 psi,Heat Transfer Effeciency : 127%(Ice Rink Area to Pipe Surface Area),Pipe Spacing : 1" (centre to centre) ,Diameter 1/2" (o.D.) 1.5mm thick.total number of pipes 2180 pipes.Design : Pipe cut based on ice rink shape,Hose Barbs: None,Connectors: Full Flow push fit connectors and multi seal Technology,Pipe Chairs : Virgin high density Polythylene, Custom made , 1 ft. spacing.

Portable, Reverse - Return Header (Side Header)- Supply, Installation, Testing and Commissioning of material not less than following specifications : Sch. 80 Polyvinyl Chloride Diameter: 6",Standard : ASTM D1785,Design: Pre- fabricated with custom -groove for Victaulic Coupling Mount,Thread : 1/2" NTPF, 48 holeslength : 4 ft (end to end), Refrigerant Transmission Pipe System -Supply, Installation, Testing and Commissioning of material not less than following specifications :SCh. 80 polyvinyl Chloride Diameter: 6" ,Standard : ASTM D1785,Design : Pre-fabricated with custom -groove for victaulic coupling mount ,Standard length: 20 ft. (end to end),Pressure Gauges: 100 to 300 PSI Range (reading) mounted to the pipe with isolation valves ,Isolation Valves : Standard Butterfly Valve for 6" Diameter,Flow Meter: Standard Device up to 1500 gallons/minute reading.

Chiller Supply, Installation, Testing and Commissioning of material not less than following specifications, Capacity ; 330 tons general design :- three packaged units,110 tons each.compressor: screw type compressor.control system: programmable logic controller, individual controller for each unit user interface: colored touch screen evaporator: shell and tube condenser : aluminium finned tube , air condensed system, high speed fan glycol leaving temperature : -15 C glycol entering temperature : -13 C maximum ambient : 40 C The Chiller will have programmable logic controller central processing unit and touch screen user interface. Supply Installation, Testing and Commissioning of Chiller unit complete with chiller, compressors, refrigerant, pumps sets, water coolers, electrical panels, incomer MCCB, etc. all complete. Chiller unit appx 450KW ,Frame unit shall be designed to install indoor machinery room with refrigeration and coolers to be placed on the roof of the machinery room.

All parts of the cooling unit and pumping set shall be installed on the same frame . Refrigeration unit and pumping set shall be controlled by a common control panel. Apart from compressors and heat exchangers the cooling unit shall contains but not limited to the following systems and facilities:• Compressor capacity control based on brine return temperature measurement• Evaporator injection control system• Refrigerant emergency discharge system• Brine booster pump for ice rink cooling piping• Ice rink piping automatic venting system• Brine flow control system and circulation pump control system• Brine thermal expansion compensation system• Automatic condensation pressure maintenance system• Free cooling system

Refrigerating unit shall be completely factory tested and test run. Refrigerating unit shall be made according to CE rules and shall be installed separately from the refrigerating unit Fillings - 1 set synthetic refrigerant oil for two filling 80 l- 1 set refrigerant filling approx. 200kg or refrigerant as per chiller specification. Skid: 6" Steel C channel,2.88meterx 2.82 m, Top Cladded with 3 mm Checkered plate.Pump: 2 units, close coupled centrifugal,120ft. TDH, 800 gallons per minute.Electrical supply: as per site requirements,Y- strainer: ASTM 6",Isolation valves: ASTM 6",Check Vave : ASTM 6 ",Byepass Valve: ASTM 3" ,Air Seperation : ASTM 1/2 " Ball Valve,Glycol Charging port: 1" Ball Valve,Level Detector: 1/2" glass tube with brass fittings.Electrical Box.: Double Door, IP 55,Control : Variable frequency Drive and Direct on line.Insulation : 2" rubber insulation for the Glycol Expansion Tank and piping.Cladding : Aluminium cladding for Glycol expansion tank and piping.paint : Custom color,custom built pump station with dual pump (one running, one standby) expansion tank, pre-welded piping and built in electrical control panel. Each pump will be driven by variable fequency drive (VFD) for variable flow of the system.

Other Items -Supply, Installation, Testing and Commissioning of material not less than following specification : Ice Building Equipment, Maintenance Tools and Ice Paint, to install your first ice sheet, all the tools needed to professionally install and maintain ice sheet .Three ice product mixing tubs, a 1.5 h.p. electric pump, a patented ice building two nozzle set, a 19 mm make up water hose, a stirring paddle, three 19 litres pails, and a 25.4 mm diameter applicator (for the full length of the rink)are included.Ice chipper: this heavy duty tool is a must for chipping away any unwanted ice building-up as around doors .Ice Scraper: this stainless steel tool is used to shave off the ice unwanted items (like split ice paint or blood paint).Rink Squeegee: with a true radius design makes this push squeegee the best in the market for clearing ice of excess water, like around the resufacer gate.Hand snow plow: a 48" (1.2 m) wide and is used to push, from the ice, the snow droppings from the ice resurfacer at the equipment gate . In the event of a break down of the ice resurfacer, several hand snow plows can quickly clear the rink) .Snow Scoop: a large mouth, heavy duty, high impact and easily scoops up the snow droppings from the ice, left by the resurfacer at the equipment gate . This heavy duty snow scoop offers years of service as it will not bend or corrode.

Supply, Installation, Testing and Commissioning of Ice Making Products not less than following specification:instant ice : is blended into water to create a slurry of slush, which is used to seal the porous sand rink floor with an instant ice glaze.Slush ice: is added to form a room temperature slush. When installing the intial ice sheet it seals the seam where the boards meet the rink floor. During the season it is used to repair cracks and divots in the ice. Ice building Additive: is a liquid concentrate, which is added to the cold ice building water when installing the intial ice sheet each season. Hot water for building is eliminated because IBA reduces the tendency of the water to produce ridges when building ice.With IBA the cold treated water flows evenly across the ice for a smooth ice surface. IBA also allows entrapped air to escape from the ice building water thus creating a denser ice sheet. This denser ice is more energy effecient, all season long.Base ice:- This powder is added to water to form a thickened ice solution which is sprayed onto the rink floor to opaque out(white over) the dark colour of the rink floor with layers of white ice. The Base ice secret is the use of only titanium dioxide crystals, as the pigment: this provides the whitest ice available. Slick ice:- a liquid concentrate that is mixed with cold resurfacing water and eliminates costly hot water ice resurfacing. Thisa unique internationally patented, prtoduct not only saves energy but also provides an improved shiny and faster ice surface. Slick ice resurfacing cuts down on the fogging of the rink air. The first month supply shall be included.

Supply, Installation, Testing and Commissioning of Professional Ice Resurfacer not less than following specification:Rapid Blade - charge system,Patented worms washing system,CAN BUS control with color touch screen,Maintainance free A/C (alternating current) electric motors.Ice BOOST - snow crusher for screw conveyors,Side brushes,Signal tone when reversing, opening/ closing of the snow tank,Servo Driven oil immersed brakes in front and rear with mechanically operated parking brake ,Snow tank capacity 3.0 m3,Water tank in PE - HD with capacity 1,000 ltrs. 80V, 805 Ah battery ,high frequency battery charger,2 standard blades,2 wipes,Led headlights front and rear,LED snow tank headlights,LED rotating beacon,Sprung adjustable drivers seat with armrests,USB port,Rear Mirror,CE Compliant. Providing and commissioning of Full size Ice surfacer, Electric or Diesel operated. Make: Mammoth, Zamboni, Olympia, or equivalent - Blade width: 2.300 mm- Snow tank: 3 m³ compacted 3,7 m³- Speed: 0 - 13 km/h

Supply, Installation, Testing and Commissioning of STANDARD EQUIPMENT not less than following specifications:- PLC control- 5.7 inch colour display: high resolution with 5 control buttons for setting following functions: time, water tank level, switching of delays for washing system, events, service / maintenance- Present indicators on main screen: Battery state of charge, current consumption, driving speed, outdoor temperature, water tank temperature, water tank level, cutting depth planning blade, time, various indicator lights- Button for automatic modus: Operations start automatically in a fixed order- Function for automatic water fi ling system with immobilizer (water stop valve as optional)- Electrical snowbin inspection hatch- Audible signal for reverse, snow bin cover operation, reverse of the screw conveyors and blade exchange- Spring-suspended and height-adjustable drivers seat (fabric) with armrests- Spring suspended passenger seat- Easily accessible engine compartment (tiltable) with cap support- High performance traction batteries with cells with tubular positive plates- Electric battery water refi ling system with 50 litres tank- Maintenance-free a.c. electromotors- Water tank made of PE- Coated snow bin- Service brake with hydraulic brake force booster- Hydraulic negative parking brake- Hydraulically driven and swivelling side brush- Board guide pulley- Side mirror, rear- Snow bin headlight, side headlight- Flashing warning light- Led daytime running light- System for water stabilization also in curves- Constant grinding pressure planning system- Quick-Change-System for a fast blade replacement- One-piece blade made of high-speed steel HSS (one set contains 2 pieces in a wooden box)- Factory-mounted connections for WM attachments- 2 wiping clothes- CE certify cation- User manual with spare part list,Stainless steel edger, spring borne with electric height adjustment, Blade = 2300 mm,Connections for attachments,Side mirror front left,Side mirror front right,Snow bin wash system,Horizontally screw conveyor wash system,Vertically screw conveyor wash system,Proportional water metering with pump inclusive device for washing systems,Ice washing system,Electrically powered cloth support,Spare wheel 16“ with cross-key,Diagnostic cables for online support,Water stop valve 1" 1/4 for water filling system,JPKFP Wiper cloth = 2300 mm,Driver‘s seat heating seat pad and backrest,Tool set,Lifting jack with bar 10 t (long version), Spare parts for Ice Surfacer ,Introduction- Supply, Installation, Testing and Commissioning of tools for ice resurfacing not less than following specifications - Blade sharpening machine for Ice resurfacer Length: 3000mm,Width: 440mm

Supply, Installation, Testing and Commissioning of Other Equipment not less than following specifications -ONE Scoreboard Black Box,Goal lights,External Start/Stop Controller,External 4 Button Controller,TWO TONE HORN (power 112 dB / 130 dB),Splitter for 4 monitors. Supply, Installation, Testing and Commissioning of Other Equipment Skate sharpener not less than following specifications- Blade master Model BRC2005, 2-IN-1 COMBO SKATE SHARPENER (TRAVEL MODEL),Grinding wheel red 60/80,Grinding wheel blue 60/80,Diamond,Blade Angle Tester,400 pairs of ice rental skates various sizes .

ELECTRICAL INSTALLATIONS WORK- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm HR-FRLS-H-LF (HEAT RESISTANT FLAME RETARDANT LOW SMOKE HALOGEN - LEAD FREE) PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm HRFRLS-LR PVC insulated copper conductor single core cable etc. as required. (Polycab/Havells/Finolex for wires and Legrand/Hager/Siemens for switch make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

a) Group A.

b) Group C.

Wiring for twin control light point with 1.5 sq.mm HR-FRLS-H-LF (HEAT RESISTANT FLAME RETARDANT LOW SMOKE HALOGEN - LEAD FREE) PVC insulated copper conductor single core cable in surface recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm HR-FRLS-H-LF PVC insulated copper conductor single core cable etc. as required (Polycab/Havells/Finolex for wires and Legrand/Hager/Siemens for switch make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Group C.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm HR-FRLS-H-LF (HEAT RESISTANT FLAME RETARDANT LOW SMOKE HALOGEN - LEAD FREE) PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, and earthing the point with 1.5 sq. mm HRFRLS-LR PVC insulated copper conductor single core cable etc as required. (Polycab/Havells/Finolex for wires make or equivalent or as approved by site engineer)

Group A

Group C

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections (Legrand/Hager/Siemens make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required (Legrand/Hager/Siemens make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. (Legrand/Hager/Siemens make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing PVC batten/ angle holder including 9W Led Blub and complete connections (Anchor/Havells/Philips make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. (Polycab/Legrand/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

1 run of cable

Supplying and drawing following sizes of HRFRLSH-LF PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. (Polycab/Havells/Finolex make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

1 x 1.5 sq. mm

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of HR-FRLS-H-LF PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Polycab/Havells/Finolex make as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of HR-FRLS-H-LF PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Polycab/Havells/Finolex make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. (Precision pipes/Jindal/Di-plast make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

20 mm dia. ISI marked, PVC conduit

25 mm dia. ISI marked, PVC conduit

32 mm dia. ISI marked, PVC conduit

40 mm dia. ISI marked, PVC conduit

Supplying and fixing 6 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required (Legrand/Schneider/L&T make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Single pole

Double pole 32Amp

Triple pole and neutral 32Amp

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required (Legrand/Schneider/L&T make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

25 Amps. Cat-A

40 Amps. Cat-A.

63 Amps. Cat-A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required (Legrand/Schneider/L&T make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

40 Amps. Cat-A.

63 Amps. Cat-A.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (Legrand/Schneider/L&T make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Double door-4 way

Double door-6 way

Double door-8 way

Double door-12 way

Supplying and fixing following way, Horizontal type/Vertical type (As per site) three pole and neutral, sheet steel, MCB distribution board, 415V,on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (Legrand/Schneider/L&T make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Double door-4 way (4+12),horizontal type

Double door-6 way (4+18),horizontal type

Double door-8 way (4+24),horizontal type

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan with BLDC Motor, making good the damages, connections, testing and commissioning etc (Usha/Atomberg/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Exhaust Fan, Light duty, Sweep 20 cm (200 mm) Usha make Striker High Speed Exhaust

Exhaust Fan, Metal Heavy duty, 300 mm sweep, Usha make TURBO HEAVY DUTY

Providing and installation of stationary storage type Electric water heater Andris Slim 30 ltrs Geyser Racold Make (Geyser) by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc.(Racold/Bajaj/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

30 Liter capacity water heater (Cat-A) 4 Star

50 Liter capacity water heater (Cat-A)

6 Liter capacity instant water heater 5 Star

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-(Legrand/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

2 modules (78mmx78mmx50mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections (Legrand/Hager/Siemens make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Telephone Socket outlet modular type Legrand Make 6792 62 RJ11

T.V. Socket outlet modular type Legrand Make 6792 60

RJ-45 Legrand make 6792 64 connector

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required (Polycab/Havells/Finolex make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required (Polycab/Havells/Finolex make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase, 230 volts complete as required (Bajaj/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Earthing including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

G.I. earth plate 600 mm X 600 mm X 6 mm thick

Copper earth plate 600 mm X 600 mm X 3 mm thick

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts..(For vertical run

Providing and fixing following size copper strip on surface or in recess for connections etc. as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

25 mm X 5 mm

32 mm x 6 mm

Providing and fixing 8 SWG dia Copper wire on surface or in recess for loop earthing along with existing surface/ recessedconduit/ submain wiring/ cable as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size:- (Polycab/Havells or ISI make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Armoured cable 6sq. mm (2 core)

Armoured cable 10 sq. mm (4core)

Armoured cable 16 sq. mm (3.5 core)

Armoured cable 35 sq. mm (3.5 core)

Armoured cable 50 sq. mm (3.5 core)

Armoured cable 150 sq. mm (3.5 core)

Armoured cable 240 sq. mm (3.5 core)

Armoured cable 300 sq. mm (3.5 core)

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation and refilling the trench etc.as required, but excluding sand cushioning and protective covering:- (Polycab/Havells or ISI make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Armoured cable 6 sq. mm (2 core)

Armoured cable 10 sq. mm (4core)

Armoured cable 16 sq. mm (3.5 core)

Armoured cable 35 sq. mm (3.5 core)

Armoured cable 50 sq. mm (3.5 core)

Armoured cable 150 sq. mm (3.5 core)

Armoured cable 240 sq. mm (3.5 core)

Armoured cable 300 sq. mm (3.5 core)

Providing and fixing following type of Surface fixture MONDO HEXA Havells make Cat no. MONDO600HEXP/S36WLED830SPSWH, 36 Watt 3000K complete with all accessories, connections, testing and commissioning etc. as required. (Havells/Jaquar/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing following type of Surface fixture Sleek Surface Downlight Philips make SM251C LED20S- 3000 PSU WW 20 watts complete with all accessories, connections, testing and commissioning etc. as required. (Philips/Jaquar/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing following type of Recess ARUMI Panasonic make Cat No. PDLM26203 20W 3000K WW colour complete with all accessories, connections, testing and commissioning etc. as required. (Panasonic/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of HARROW PLUS AL Panasonic make Cat no. PBTM17228, 22W, 4000K Tub, LED batten for surface and suspended applications. Aluminium housing, high transmissibility diffuser with high lumen output, complete with all accessories including connections, testing and commissioning as required (Panasonic/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of Surface mounted TRUSS ADV Panasonic make Cat No. PBTM05404, 40W, 4000K IP65 Batten with inbuilt heat sink, polycarbonate housing equipped with anti-glare diffuser & energy efficient electronices driver complete with all accessories including connections, testing and commissioning as required (Panasonic/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of Mondo Havells Make Cat No. MONDO400RDP/S25WLED830SPSWH, 25 Watt, WW Coloiur, Dia 400 mm, Height 70 mm, including connections, testing and commissioning as required (Havells/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of Wall bracket (light) Jaquar make Cat No. 300.00.NGG, Pisa Wall Light E-27 (including E-27-20 Watt bulb-3000lm Warm White colour) complete with all accessories including connections, testing and commissioning as required (Jaquar/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying, storing, assembling, fixing, testing & commissioning of chandeliers including cost of hangers, chains or any other item required for fixing, including flexible wire from outlet to fitting, Jaquar make or its equavalent as approved by the engineer Incharge for indoor application suitable for installing on existing ceiings etc for designer lighting purpose complete in all respect. The work involves assembly, fixing, connecting, commissioning and testing of the fixtures. including carriage of material in all leads, lifts and heights through mechanical or manual trasport CONCEALED LIGHT CHANDELIER: Starling Jaquar make Cat No. CHL-GLD-AS80881B, Starling chandelier with asfour almaaza crystal (D 500 x H 180 ), Color: Gold, Material: Brass casting, No. of heads: 3, Cap type: E14, Wattage: 3 x 4 W LED, (Jaquar/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of Philips make 11Watt model no. 31165 Mirror Light complete with all accessories including connections, testing and commissioning as required. (Philips/Jaquar/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing of Gate Light Post Top Vista LP09S, Product Code: LP09S-501-XX-57-XX, 4000K, 45Watt Wipro Make and complete with all accessories including making connections, testing etc. as required (Wipro/Philips/Havells as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying,installation,testing and commissioning of Astronomical time switch Havells make Cat No. DHTQB01016 2 output per phase and suitable for single,capable of following output in feeder pillars / Lighting DBs for automatic switching On & OFF of street lights at sun set & sun rise or twilight (Auto ON, Auto OFF, Auto) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming and with Magnetic Contactor 4 Pole Power Contactors with AC Coil 2NO + 2NC Cat No. IHPHC032122, at site complete as required. (Legrand/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supply, Installation, testing and commissioning three phase Bus-Bar chamber with specific MCCB and space for incoming/outgoing cables, wall mounting type, front operated all complete with interconnections and painted with powder coated as per direction and approval of the site engineer including all leads and lifts. (Havells/L&T make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

63 AMP three phase Bus Bar Chamber Havells make Cat No. IHBC006308 with Havells make Cat No. IHDA6TBF0063 ,63 Amp FP, MCCB

100 AMP three phase Bus Bar Chamber Havells make Cat No. IHBC010008 having with Havells make Cat No. IHDA6TBF0100,100 Amp FP, MCCB

200 AMP three phase Bus Bar Chamber Havells make Cat No. IHBC020008 having with Havells make Cat No. IHD2HTBF0200, 200 Amp FP, MCCB

Supply, Installation, testing and commissioning of 100 Amp FP Changeover switch in SS enclosure, Havells Make Cat no. IHCNFE0100 having space for incoming/outgoing cables, wall mounting type, front operated all complete with inter connections and painted with powder coated as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.(Havells/L&T make or equivalent)

Supplying and fixing of Boundary wall Light Havells LEXO (PRISMATIC) Cat No. LHFOGAE1T11F0, high grade unbreakable polycarbonate material suitable for 20 W LED lamp B22 base. including 0.30 mtr. 40mm G.I.pipe for fixing, containing one no. 2way MCB DB ,6 Amp. MCB, painting complete with all accessories including 5W LED lamp including making connections, testing etc. (Havells/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing of following fixtures complete with all accessories including making connections, testing etc. as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Suspended Bulk Head Well Glass Jaquar make Cat No. LWGL01X040XC, 40 Watts, Dia: Ø 130 mm, Height: 206 mm, (Jaquar/Havells/Philips make or equivalent )

Bulk Head Jaquar make cat No. LBLK02X010XW, 10Watts, WW in Colour, Length: 193 mm Width: 118 mm, Height: 56 mm (Jaquar/Havells/Philips make or equivalent )

Providing and fixing following type of Recess Fixture Wipro make Mollis LD06, Cat No. LD06-151-XXX-57-XX, Warm White, 12Watt complete with all accessories, connections, testing and commissioning etc. (Wipro/Philips/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing following type of Surface Fixture Wipro make Mollis Surface LD06, Cat No. LD06-151-XXX-57SMG1, Warm White, 12Watt complete with all accessories, connections, testing and commissioning etc. (Wipro/Philips/Havells make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Fire Alarm System- SITC of 1 Loop Analogue Addressable Fire Alarm Control Panel Ceasefire make expandable upto 2 Loop, loop current 500mA maximum per loop, dual flash based microprocessor, supports to connect 240 addressable devices one each loop via fully digital communication protocol, equipped with a white backlit display (240x64 pixel resolution) graphical LCD Display with atleast 6 lines of information, 200 fire zones (soft zones), fully programmable via alphanumeric keypad or configuration software, dedicated USB and RS-232 serial port for direct or PC connection, 5500 events storage, loop current 500 mA, panel shall be equipped with in-built multimeter for live monitoring of loop current, earth voltage, loop voltage etc., installer's logo application, can be networked to compatible addressable panels and repeater panels by adding a network card, features battery charger status and temperature, supports programmable cause / effect on outputs, panel housing meets IP30 ingress protection classification. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of Intelligent Sounder Interface Module Ceasefire make allows to connect conventional Sounder or Sounder Beacon to addressable loop, with in-built short circuit isolator, allows for two stage alarm capability, addressed through auto and manual options, approved by LPCB for EN 54-17 & EN 54-18 standard. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Intelligent Analogue Optical Smoke Detector Ceasefire make with advanced optical chamber and smoke inlet design to provide resistance to entry of dust to provide immunity to false alarms, programmable multiple smoke senstivity level setting, bi-directional in-built short circuit isolator to protect against cable faults, dual bi-colour LED's with 360 degree view of status, auto-addressable/electronically addressed, utilises fully digital communication addressable protocol with high noise rejection approved by LPCB for EN 54-7 & EN 54-17 standard, complete with Standard Detector Base for mounting the compatible addressable detectors. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Intelligent Analogue Multi-Criteria (combination of smoke and heat) Detector Ceasefire make with special algorithms to utilise information from both smoke and heat sensing elements to ensure high level of immunity to false alarms without compromising genuine alarm sensing performance, programmable multiple smoke senstivity level and 9 modes of operation, bi-directional in-built short circuit isolator to protect against cable faults, dual bi-colour LED's with 360 degreeview of status, auto-addressable/ electronically addressed, utilises fully digital communication addressable protocol with high noise rejection approved by LPCB for EN 54-5, EN 54-7, & EN 54-17 standard, Complete with Standard Detector Base for mounting the compatible addressable detectors. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Intelligent Analogue Manual Call Point Ceasefire make with resettable operating element, with in-built bi-directional short circuit isolator, Bi-Colour LED for local indication of device status, single action operation, reset to normal condition using special reset key, clearly visible alarm flag in the activated state. Approved by LCPB for EN 54-11 standard. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Single Loop Driver Card Ceasefire make designed for use with compatible analogue addressable panels, provides control and connection/communication to maximum 240 addressable device per loop. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Intelligent Sounder Interface Module Ceasefire make allows to connect conventional Sounder or Sounder Beacon to addressable loop, with in-built short circuit isolator, allows for two stage alarm capability, addressed through auto and manual options. Approved by LPCB for EN 54-17 & EN 54-18 standard. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Translator module Ceasefire make, shall allow addressable loop communication to 32 wireless field devices, system devices can be configured through translator module or software, loop powered, two orthogonal antennas for safe and reliable wireless communication, shall have high wireless tranmission range with wireless field devices of max. 150 meter in open space, maximum radiated power 5dBm (3mW), enabled with 7 operating frequency channels for bi-directional wirelesss communication, operating frequency range 865MHz, IP 65 rated. Approved by LPCB for EN 54-18 and EN 54-25 standard. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of follwoing items including carriage upto all lead and lift and as per direction of the Engineer in Charge.

Mounting Accessories like back box for detectors, devices & cable glands, etc. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent),

24V 3A DC adapter Ceasefire make for expander. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent),

SITC of Response Indicators outside the rooms for getting fire indications of detectors installed above false ceiling / for particular zone / for Loop devices / as a Panel to loop cable complete as required. (MAKE: Ceasefire/Siemens/Honeywell or Equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Talk back receiver AHUJA CCS-2300, 2-WAY COUNTER COMMUNICATION SYSTEM as per specification complete (MAKE: Ahuja or equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Ceiling/ Wall Mount Speaker with operations 6 Watts, (Black LBD 3902 Bosch 6W Wall Mount Speaker) (MAKE: Ahuja, JBL or equivalent), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

Supplying & Fixing of Energy saving display EXIT sign board Glass type specially designed for classic décor with excellent quality high efficiency and long life for single / both side display, well ventilated, powder coated having nominal size LED lamp, battery backup 6 hour to be installed on wall / ceiling etc. complete as required. (MAKE: FGE/ LEGRAND/ ABB), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

Providing & installing self glow signs luminescent U-1000 Alu. sheet with 2 mm thickness sheet on the wall / ceiling etc for the size of (4''x12'' ) as reqd.(Make : Nightglow/FGE), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

Supplying and laying of 1.1 KV Grade 2 X 1.5 sq.mm. copper cables on surface / conduit complete with clamps etc as reqd. (MAKE: Polycab/ KALINGA/ GRANDLAY), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

Supplying and laying of 4 x 1.5 sq.mm. PVC insulated PVC sheathed copper conductor armoured control cable of 1.1 KV grade complete as required. (From Main Fire Control Panel to the Repeater Panel). (MAKE: Polycab/ KALINGA/ GRANDLAY), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

Providing and fixing of following size of black enamelled MS conduit in recess / on surface including all accessories, proper saddling at every 1200 mm intervals and hooks, where imbedded in the wall, MS junction / pull boxes, GI fish wire, complete as required, including carriage upto all lead and lift and as per direction of the Engineer in Charge.

40 mm dia Conduit

32 mm dia Conduit

25 mm dia Conduit

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. (Polycab, Havells or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Speaker cable Single pair, 2-core, 1.5 sqmm

EPABX System- SITC of Digital Hybrid IP-PBX System configured for 02 Analog Trunk Connectivity, 02 Digital Extensions, 16 Analog Extensions. It should be possible to reach the capacity of system to 48 ports and 99 IP users without any add-on CPU or chassis/hardware platform. System should have two Gigabit Ethernet ports for LAN and WAN to separate out local and VoIP traffic on external network.It should be suitable for DTMF as well as the FSK type of telephone instruments. It should have built-in multi-party conferencing without any software licensing. It should be possible to carry out 15 conferences of 3-participants at a time. The system shall have built-in web based software programming tool for system administration. The call ringing sequence would be programmable and have options such as simultaneous, hunting off, round robin and delayed simultaneous.The system shall support flexible numbering for extensions such as it may have extensions with 1 digit, 2 digits and up to 6 digits numbers as well as in combination of all.The system should have built-in outgoing Call Log buffer of 6000 calls, incoming call log buffer of 5000 and call log buffer of 1000 internal calls. Operator features shall have the assistance to extension, attended call transfer, call intercept, indication of call waiting, night service control etc. should be available by default.complete including carriage upto all lead and lift and as per direction of the Engineer in Charge. (Matrix/Dlink or equivalent)

SITC of Operator-cum maintenence console with large Backlit Display of 240x60 Pixels Graphic LCD, 4 Context Sensitive- Keys, Built-in 16 DSS Keys, High Quality Full Duplex Speaker Phone Features Call Forward, Waiting, Transfer, Hold, Conference, Redial, Ringer Lamp and must have storage for minimum 20 calls per call log in the consolen itself. (Matrix/Dlink or equivalent) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of Main Distribution Frame (MDF) with Integrated Protection Module (IPM) complete as required, including carriage upto all lead and lift and as per direction of the Engineer in Charge. (Matrix/D-link or equivalent or as approved by the Engineer incharge)

SITC of 3KVA UPS on line, ON LINE UPS 3KVA 1PH:1PH 72V MAX+SKU: 899-601-3001 | CATEGORY: ONLINE UPS Microtek High Frequency, provides Uninterrupted Pure Power for Critical Applications such as Computer Network, Servers, Cyber Cafes, ATM Machine, Labs etc. High Frequency and Double Conversion Online Technology, High End IGBT Based. & Micro Controller Based, Wide Input Voltage Range & Advanced PFC Technology, Advanced Battery Management & Battery Charging in UPS Off Mode, Short Circuit and Overload Protection & SNMP Card Slot (Optional), Smart RS232 Communication with monitoring software, Over Temperature Protection. & EMI / RFI Noise Filter, LCD/LED Display simultaneously & Generator Compatible Specially designed to suit Indian Power and Environment Condition, Isolation Transformer (Optional) & Different Output Voltage settings., Output, Frequency fixed at 50Hz or can be synchronized with Input Frequency., Static Bypass Enable, Disable & Outlets Programmable & Non Programmable, Protection from DC Fan failure & In-built Over Voltage Cut-Off Device, including required no of batteries for 30 mintues of backup (Make: Microtek/Emerson/ MITSUBISHI), including carriage upto all lead and lift and as per direction of the Engineer in Charge.

SITC of Telephone instruments of Panasonic cat no. KX -TSC60SXB Black, Landline Phone, with necessary cable etc, complete as required, including carriage upto all lead and lift (Panasonic/Beetel/Motorola or equivalent or as approved by the Engineer incharge)

Surveillnace System (CCTV)- SITC of HIKVISION IP 4MP COLORVU BULLET CCTV (DS-2CD1047G0-L) 4 MP ColorVu Fixed Turret Network Camera, High quality imaging with 4 MP resolution, Excellent low-light performance, Efficient H.265+ compression technology, Water and dust resistant (IP67), 24/7 colorful imaging, 12V, one year Warranty and as per direction of Engineer-in charge and specifications as required including carriage of material in all lead and lifts through mechanical and manual transport. (Hikvision/Samsung/Sony or equivalent or as approved by the Engineer incharge)

SITC of HIKVISION IP 4.0MP DOME NETWORK CCTV CAMERA (DS-2CD1343G0E-I) 4 MP ColorVu Fixed Turret Network Camera, High quality imaging with 4 MP resolution, Excellent low-light performance, Efficient H.265+ compression technology, Water and dust resistant (IP67), 24/7 colorful imaging, 12V, one year Warranty and as per direction of Engineer-in charge and specifications as required including carriage of material in all lead and lifts through mechanical and manual transport. (Hikvision/Samsung/Sony or equivalent or as approved by the Engineer incharge)

SITC of HIKVISION IP 4MP 25X 100MTRS PTZ SPEED DOME CAMERA (DS-2DE4425IW-DE) 4-inch 4 MP 25X Powered by DarkFighter IR Network Speed Dome, 1/2.8" progressive scan CMOS, High quality imaging with 4 MP resolution, Excellent low-light performance with powered-by-DarkFighter technology, 25× optical zoom and 16× digital zoom provide close up views over expansive areas, WDR, HLC, BLC, 3D DNR, defog, regional exposure, regional focus, Expansive night view with up to 100 m IR distance, Support H.265+/H.265 video compression, one Year Warranty, as directed by Engineer-in charge and specifications as required including carriage of material in all lead & lifts through mechanical & manual transport (Hikvision/Samsung/Sony or equivalent or as approved by the Engineer incharge)

SITC of HIKVISION 32 CHANNEL 4K H. 265+ NVR (DS-7732NI-K4), Third-party network cameras supported upto 8 Megapixels resolution recording, Support 1-ch HDMI, 1-ch VGA, HMDI at up to 4K (3840x2160) resolution, incoming bandwidth: 256Mbps; Outgoing bandwidth: 160Mbps, Support H.265+/H.264/MPEG4 video formats, 4 SATA Port of 8TB each, including minimum length of 3mtrs Honeywell make or equivalent Ultra High Speed HDMI 2.1 Cable with Ethernet, Ultra High Speed HDMI Cable 48GBPS, Supports 3D/4Kx2K/8K Ultra High Definition @60Hz and NVR with one year Warranty complete and as directed by Engineer-in charge and specifications as required including carriage of material in all lead & lifts through mechanical & manual transport or its equivalent as approved by the Engineer in Charge. (Hikvision/Dahua/Samsung or equivalent or as approved by the Engineer incharge)

SITC of Power Supply ISI MARK including 1 year maintenance and as per direction of Engineer-in charge and specifications as required including carriage of material in all lead and lifts through mechanical and manual transport or its equivalent as approved by the Engineer in Charge.

SITC of following POE switch including 1 year maintenance as per required specifications as per direction of Engineer-in charge, including carriage of material in all lead and lifts through mechanical and manual transport, as approved by the Engineer in Charge.

HIKVISION 16 Port Giga PoE Switch Cat No. (DS-3E0518P-E/M) (Hikvision/Samsung/Dlink make or equivalent)

HIKVISION 8 Port PoE Switch (DS-3E0109P-E/M) (Hikvision/Samsung/Dlink make or equivalent)

SITC of DC Connector including 1 year maintenance and as per direction of Engineer-in charge and specifications as required including carriage of material in all lead and lifts through mechanical and manual transport or its equivalent as approved by the Engineer in Charge.

Providing and fixing Samsung 108 cm (43 inches) Crystal 4K Neo Series Ultra HD Smart LED TV UA43AUE65AKXXL (Black) including one year maintenance and as per direction of Engineer-in charge and specifications as required including carriage of material in all lead and lifts through mechanical and manual transport . (Samsung/Sony/LG make or its equivalent as approved by the Engineer incharge)

Providing and fixing Polycab make cctv 4+1 wiring for fixing of cameras in the existing PVC conduit as per requirement & one year maintenance and as per direction of Engineer-in charge and specifications as required including carriage of material in all lead and lifts through mechanical and manual transport. (Polycab/Finolex make or its equivalent as approved by the Engineer incharge)

Providing Hard disk (8TB hard disk WD make) including 1 year maintenance and as per direction of Engineer-in charge and specifications as required including carriage of material in all lead and lifts through mechanical and manual transport. (WD/Seagate or equivalent or as approved by the Engineer incharge)

Providing and fixing of Crotomak make 6U NVR Network Rack with 4 Power Socket and AC Axial Cooling Fan -Transparent Glass Door, Metal Cabinet Box Wall mount (Size 6: 45 X 55 X 35 cm) including connections, testing and commissioning as required (Crotomak/Plantex/Lepose make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Fire Fighting System Dry Type- Providing and fixing of Fire bucket stand Minimax make item code I00000089 for 4 buckets with four nos. fire buckets Minimax make I00016356 MMX 10 Litre complete in all respect.or as per norms of fire deptt as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of Fireman Axe with Insulated Handle Minimax make item code I00003814 (Agni/Suraksha/omex make) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing fixing, testing and commissioning PORTABLE ABC TYPE FIRE EXTINGUISHERS ”Minimax” Gas Cartridge Type Fire Extinguisher, ISI Marked (IS15683:2018), CE and EN Certified, Cat No. I00016798 MMX ABC 9 Kg IS:15683 Gas Cartridge (MAP 90) (Fire Rating 6A233B) Pure Polyester Powder Coated Body with internal and external coating, Forged brass valve with in bult Pressure Relief Device, Aluminium Siphon tube and diffuser for Dry Powder Models and Stainless Steel with Strainer for Water & Mechanical Foam Models, Stainless Steel safety pin, High durablility Vinyl label (3M make), QR Code label with printed serial number, Individually packed in 7 Ply corrugated paper box together with Wall Bracket, screws & plugs and service manual (Minimax/Ceasefire make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing fixing, testing and commissioning of PORTABLE STORED PRESSURE FIRE EXTINGUISHERS Minimax make I00014861 MMX Foam Based Watermist Low Pressure Fire Extinguisher 9L - IS:15683 (Fire Rating 4A, 75F 233 Stored Pressure Fire Extinguisher, ISI Marked (IS15683:2018), CE and EN Certified, Epoxy Powder Coated Body, Forged brass valve with in bult Pressure Relief Device and Non Return Valve for pressure gauge port, Stainless Steel safety pin, High durablility Vinyl label (3M make), QR Code label with printed serial number, Individually packed in 7 Ply corrugated paper box together with Wall Bracket, screws & plugs and service manual (Minimax/Ceasefire make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing fixing, testing and commissioning PORTABLE CO2 TYPE FIRE EXTINGUISHERS ”Minimax” Carbon Di-oxide agent Type Fire Extinguisher, I00006119 MMX CO2 4.5 Kg IS:15683 (Squeeze Grip Valve) (Fire Rating 55B )ISI Marked (IS15683:2018), CE and EN Certified, Containing CO2 gas having purity 99.7% filled in Seamless Cylinder having approval from Petroleum and Explosives Safety Organisation (PESO), coated with High Glossy PU Paint, ISI marked Dual Spindle Valve with Aluminum Wheel & Collar / Squeeze Grip brass valve, Aluminium Siphon tube, High durablility Vinyl label (3M make), QR Code label with printed serial number, Individually packed in 7 Ply corrugated paper box together with Wall Bracket, screws & plugs and service manual (Minimax/Ceasefire make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing, fixing, testing and commissioning MODULAR TYPE CEILING MOUNTED FIRE EXTINGUISHERS Minimax make item code I00007135 MMX SP 5 Kg : Modular (MAP 90) Modular Ceiling Mounted ABC Powder Type Fire Extinguisher, CE Certified, Pure Polyester Powder Coated Body, Forged brass valve with in bult Pressure Relief Device, Non Return Valve for pressure gauge port, Large Dial pressure gauge and Thermo bulb having release temperature of 68°C, High durablility Vinyl label (3M make), QR Code label with printed serial number (Minimax/Ceasefire make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

DG Set- Supply and commissioning of 125 KVA silent type DG set Cat No. CS125D5P, Cummins engine make Cat No. 6BTAA5.9G13, Engine BHP 159, 125 KVA Cummins® ‘S Series’ diesel generating sets, powered by Cummins ‘S Series’ engines, are rated at 1500 RPM and conform to ISO 8528 specifications. The engines are radiator cooled, four stroke and multi-cylinder, conforming to BS 5514/ISO 3046. Alternator: Synchronous alternator of Stamford make suitable for continuous operation at 1500 RPM, 415 Volts, 0.8 pf (lag) suitable for 50 Hz, 3 phase, 4 wire system, conforming to BS 5000 / IS 4722. The alternator is brushless type, screen protected, revolving field, self excited, self regulated through an AVR. The alternator has the following features: + 1.0 % Voltage regulation (max.) in static conditions, IP: 23 protection with insulation class H, Permissible overload of 10% for one hour in 12 hours of operation. Mounting arrangement: Engine and alternator are mounted on a common MS fabricated base frame with AVM pads. Control panel: The control panel is manufactured with 14/16 gauge CRCA sheet and is powder coated for a weather-proof and long lasting finish. The control panel consists of following parts: Instrument cluster displaying water and lube oil temperature, lube oil pressure, engine RPM, running hours, battery charging current with LED Indications for battery charging failure, high water temperature and low lube oil pressure MCCB of suitable rating with overload and short circuit protection Combined meter for voltage, amps and frequency, Current transformers, Aluminum busbars of suitable capacity with incoming and outgoing termination, Indicating lamps for “Load On” and “Set Running” Instrument fuses duly wired and ferruled. DG set suitably housed in CPCB-II approved acoustics enclosure with standard accessories.i.e control panel, fuel tank, Battries with leads, cold start kit and AMF Panel as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supply and fixing of Rubber insulation matt 2mtrx1mtrx12mm to prevent electric shock as reqd complete in all respects as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supply, installation, testing and commissioning of following MS exhaust pipe medium duty class-B complete with all accessories such as bends flanges,gasket, flexible connections at a suitable distance and supporting arrangement as required at site as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Ornamental poles- Supply, erection and testing of ornamental pole 3000 mm high, cast aluminium, polyester/PU painted Black, LuxMax IMPERIAL-E Pole, Twinkle Make for road side and landscape lighting in position on required M.S. base plate including excavation of pit and refilling the same with cement concrete of 1:3:6 /1:2:4 from the bottom of the flushing to the ground level. The pole should be hot dip Galvanized in single dip to average 65 micron DFT including supply and fixing of foundation bolts (600mm length), with 1 no. 6 AMP. SP MCB with din bar arrangement and earthing links, 2nos 2cX 6 sqmm AL.Armd cable gland and Himachal Tourism logo engraved at the base of the pole complete in all respect and with one coat of paint Complete in all respect Twinkle/Bajaj/K-Lite make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing of Ornamental Light LED POST TOP - SQUARE Small, LuxMax-PT-164 40Watts (or equivalent), 700mm in height and 295mm in Width, warm white colour as required (Bajaj/K-Lite make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Fire Fighting System- Providing, laying, jointing and testing in following sizes of MS Class 'C' (heavy class) pipes Conforming to IS: 1239/3589 with accessories like fittings including tees, elbows, reducers, flanges gaskets, G.I. nus, blots complete with all accessories as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

100 mm dia pipe

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Providing, fixing, testing and commissioning of MS air cushion tank on pump House fabricated form 6mm thick MS plate, 450 mm in diameter and 2 m in height with dished ends fabricated from 8 mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25mm dia valve, pressure gauge with gun metal stop cock complete with all accessories as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing, fixing, testing and commissioning of MS air cushion tank on pump House fabricated form 6mm thick MS plate, 250 mm in diameter and 2 m in height with dished ends fabricated from 8 mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25mm dia valve, pressure gauge with gun metal stop cock complete with all accessories as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing of Minimax make item code I00016324 MMX Fire Hose Type 1-30M length with Gun Metal Coupling ISI marked non-percolating flexible firefighting two layered delivery hose, synthetic fiber circular woven jacketed, bearing IS:636-2018, 63 mm dia, complete with instantaneous male & female coupling (IS:903) and Copper Wire binding as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Providing and fixing Minimax make item code I00003810 Hose Reel Drum With GM Nozzle & Rubber Hose - 30M Swinging Hose reel Type-A, Wall Mounted with 180° swing, specifications as per IS-884: latest revision made of high quality mild steel, powder coated in red colour. Maximum operating pressure 10 bar, Flow rate 22.5 lpm at 7 bar pressure as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supply, installation, testing & commissioning of : Gun metal ISI marked odlique pattern hydrant landing valve with 80 mm dia flanged inlet and 63 mm dia instantaneous type female outlet complete with gunmetal cap and G.I. chain, twist release type plug and all accessoSupply, installation, testing & commissioning of : Minimax make item code I00004037 Single Hydrant Valve - Gun Metal ISI marked, Inlet 80mm & Outlet 63 mm Instantaneous, ABS Blank Cap, Hydraulic Test Pressure 21 kg/cm2 for 150 sec, Flow Rate 900 LPM at 7 kg/cm2 (PCD:160 mm, Holes: 4 nos. x 19mm, Flange: 200mm x 12 mm thk)ries as per IS: 5290-1983 (Type 'A')as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of fibre glass reinforced Fire Hose Cabinet ( 30"x24"x10") out door type, made out of sheet having glazed door with 6mm thick clear Glass including necessary Locking arrangement with allen Key, powder coating with Post Office Red Paint and for Hoseing 2 Nos .RRL Hose Pipe, 1 No Branch pipe including grounding and suitable inscripting the words" Hose Cabinet" on the Box complete as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Fire Hose Cabinet (30''x24''x10'')

Providing and fixing Gunmetal Collecting head with 63 mm dia instantaneous type inlet +150 mm dia flanged outlet with built incheck valve for fire brigade connection to UG Tank +wet riser I.S 904 specification test for 20kg/mm2 Minimax Make item code I00003796, Four Way Collecting Breaching Head - PCD 240mm and including Minimax make item code I00003822 Short Branch Pipe with 20mm nozzle, 63mm Inlet & 20mm Outlet, IS:903 - Gun metal and necessary support complete in all respect as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Four Way

Providing Cast iron /steel Butterfly Valve Confirming to type P.N 1.6 of I.S 13095-1991 Complete with Flanges bolt ,nuts ,gasket etc. As per table 'E' specification complete in all respect hydraulically test to 20 K./sqcm as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

100 mm Dia

150 mm Dia

200mm Dia

250mm Dia

Providing and fixing Cast Iron/steel double flanged horizontal type with gunmetal seat non-return valve confirming to class - I of IS : 5312 including nuts, bolts, 1.5 mm thick compressed asbestos gasket as per table "E" and specifications complete in all respect as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

100 mm Dia

150 mm Dia

200mm Dia

250mm DIa

Supply, Installing, testing and commissioning of 100 mm dial type pressure gauge gate valve with all accessories as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC Pressure switchs for Main, Jockey, and stand by Diesel pumps including necessary wiring up to control panel and Ballvalve. complete in all respect as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of Kirloskar Make pump Modal DB 80/26 Electrical Motor Driven Automatic pressurisation (Main PUMP) pumping set consisting of the following as per specifications. Horizontally mounted centrifugal type single/multi-stage fire pump capable to deliver approx 2280 LPM against a total head of 70 M, having cast iron body. bronze impeller, stainless steel shaft and complete with b) Squirrel cage induction motor totally enclosed fan cooled type suitable for 415 Volts + 10% - 15% 3 phase. 50 HZ A.C. supply of suitable capacity (approx. 45 KW, 60 HP) for the above pump with synchronous speed of 2900 RPM confirming to & duly coupled with above pump coupled with flexible coupling including as per relevant Indian Standard and specifications and including all lead and lift (Make KIRLOSKAR/ Crompton Greaves or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of Diesel Engine Driven Fire Pumping set suitable for automatic opreation consisting of the following as per specification. A) Horizontally mounting,centrifugal type single/multi-stage fire pump having cast ironbody, bronze impeller,stainless steel shaft &capable of delivering 2250 LPM against a total head of 70M complete for perodical testing of thepumping set of the pumping set as per TAC rules. b) Water cooled TAC approved Diesel Engine suitable for the developing at least 72 BHP at 2150 RPM) for above pumping complete with autmatic starting mechanism, batteries,automatic battery charger unit,flexble coupling withthe pump,coupling with the pump,fuel tank, asper TAC rules including earthing,mandatory spares and tool kit. c) Common bed plate for mounting pump and Engine fabricated of suitable MS channel as per manufacturer recommendations. (Make KIRLOSKAR/ Crompton Greaves or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of PVC water storage tank (SINTEX 2 layer) of ISI: 1270 marked G.I. intel and outlet connections, 25mm nominal bore Elbo, Tee, socket, Tank nipple, float ball valve and mosquito proof PVC cover with locking arrangement (Heavy Duty) including hoisting upto all height above ground level including carriage of materials upto all lead & lift and as per direction of Engineer-In-Charge. (10000 Ltr).

Wifi Devices- Supplying, installing, testing and commissioning of D-Link DIR-3040 AC3000 High-Power Wi-Fi Tri-Band Gigabit Router, Wi-Fi 5 (802.11AC) Technology with speeds of up to 400 Mbps (2.4 GHz) + 866 Mbps (5 GHz) + 1733 Mbps (5 GHz), Six High gain exteanal Antennas for Extended coverage, 4 x 10/100/1000 Mbps Gigabit Ethernet LAN ports, 1 x 10/100/1000 Mbps Gigabit Ethernet WAN port, 1x USB 2.0 & 1x USB 3.0 port to connect USB storage and create network storage, Works with the Google Assistant and Alexa – Voice Control with Google Assistant or Alexa. (D-Link/TP-Link/Cisco or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying, installing, testing and commissioning of TP-Link RE300 AC1200 Mesh Wi-Fi Range Extender/WiFi Booster/Wireless Repeater (Up to 1200 Mbps), Intelligent Signal Light, Power Schedule, LED Control, Dual Band (D-Link/TP-Link/Cisco or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of outdoor Wall UP-Down Light Lupus Wall Light 2x3W Jaquar Make Product Code: LWWL03X203XW Die cast aluminium housing, Opal polycarbonate diffuser, Matt grey, finish Warm white IP54, including all accessory . (Jaquar/Havells/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing of Alpha Wall Washer Light Color Anthracite finish, Material Premium Aluminium Warm white Philips make Model No 58162, 12 Watts IP54 including making connections, testing etc. (Philips/Jaquar/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing of Foot Light Die cast aluminium housing Polycarbonate diffuser White and grey finish Jaquar make Cat No. LFTL01S003XW Warm White, 3 Watts including making connections, testing etc. (Jaquar/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing of Flood light Havells make JETA IRIS FL120WLED757APWBLTG, IP66, die-cast aluminium and necessary drivers complete with all accessories including P/F M.S. Cage duly painted according to its size requirement making connections, testing etc. as required Havells/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying and fixing of Jeta Alba Havells Make Flood Light Cat No. JETAALBAFLOODLIGHT70W, IP66, Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium flood light and necessary drivers complete with all accessories including P/F M.S. Cage duly painted according to its size requirement making connections, testing etc. as required Havells/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of STRIP LIGHT (24V DC) Jaquar make outdoor type IP65, Cat No. LSTP04X008XM, 40Watts, 8W/Mtr Outdoor Strip Light (1Pack of 5 Mtr RGB), necessary drivers complete with all accessories according to its size requirement making connections etc. as required Jaquar/Philips/Wipro make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

EV Charging Station- Supplying, installing,testing and commissioning of Electic Vehicle Charging Station ‎EVCARS make EV Charger Level 2, 40 Amp Portable, Evse Home Electric Vehicle Charging Station with EV Charger Plug Holder and Cable Holder, Timing Delay (SAE J1722, 230V, 16A-40A, NEMA 14-50) with 3 years warranty (EVCARS, Kazam or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

SITC of following items complete in all respect, including all accessory as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

First aid box (Dimension in cms - L x B x H - 23.6 x 15.3 x 14 make MILTON/Plantex/Cello Medical Box With Handle)

Danger Notice Plate (MYSIGN/Signoogle/ Flambird Silver danger sign board nameplate (6inch X12inch ))

Electric Shock & Management Chart Size (50 x 70 cm Language : Hindi-English Combined. The chart Should provide information on how to perform first aid in case of electic shock. Multicolour printing on 80 GSM map litho paper. The chart should be laminated on both sides with 30 micron thick plastic film making it tear & water resistant. The chart should be ideal for putting up on a wall or a board with suitable frame and glass covering (make Vidya Chitr Prakashan/teachingnest or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Electrical Test Report for complete Electrical Installation of equipment installed under the project (including DG Commissioning report, Fire Frighting installation report and other equipment test report cards and warranty cards) as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Solar Panel System- SITC of Solar power plant Luminous make Model No. NXi 325, 25KW Solar Panel System, Solar On Grid Combo - 25KW, Net Weight (Kg) Inverter - 37 kg, Panel - 20 kg, Phase: Single Phase, UPS: NXi 325, PV Panel: 325 Wp x 84 Nos, Technology (Solar) Without Battery, Inverter warranty - 2 years, Wattage (Wp) 325, Panel Type Poly Crystalline, Product Dimensions (L*W*H) Dimensions in mm: UPS-“ 339*565*172, Panel -“ 1976x991x40, DC input Range (V) 60-130, Max. supported panel power (Wp) 270, Rated AC power (W) 230V, 8.6A, Single phase, Usable current from grid (A) 24, Max Solar Panel Voltage (V) 37.39, Nominal DC 48, including all Solar Panels, inverter, UPS, DC Distribution box, Surge protectors, AC Distribution box, required Circuit Breakers, Control wires, Power Supply, Connection Cables, required Earthing and necessary foundation or necessary aluminium support channels as per the site condition, complete in all respect, including all accessory , (Luminous/Tata/Microtek) make or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Solar Light- Supplying, installing, testing and commissioning of ALL-IN-ONE SOLAR STREET LIGHT Havells make Cat No. SOLAR AIO 24W with High Efficiency Mono Crystalline Solar PV Module, Lithium Ferro Phosphate battery with in-built BMS technology, High Efficacy LED, MPPT Solar Charge Controller and Aluminium Extruded body & is specially progrmmed to automatically control the dimming and brightness of light, which increases the backup time, complete in all respect (Havells/Philips/Wipro) or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Supplying, installing, testing and commissioning of Consul make G.I. 3Mtr Octagonal Pole cat no. RROP-030, top dia 70mm, bottom dia 130mm, sheet thickness not less than 3mm, Base Plate Dimensions (L x B x T) 200 x 200 x 12mm, on road side and landscape lighting in position on required M.S. base plate including excavation of pit and refilling the same with cement concrete of 1:3:6 /1:2:4 from the bottom of the flushing to the ground level including supply and fixing of foundation bolts, complete in all respect (Consul/Surya/Bajaj) or equivalent as directed by the Engineer-in-Charge including carriage of materials in all leads and lifts.

Provisional sum The comparison of bid shall be done exclusive of provisional sum. The cost shall include cost of Environmental testing etc.a handling fee of 5% (five percent) shall be payable to the contractor on the actual cost of any approved expenditures under as Provisional sum items

SUNEHARI BAGH BUILDERS PVT. LTD. (BID ID -439940)