Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.7 LAccepted-AOC | L1 | Accepted-AOC L1 | |
| 2 | L2₹1.7 L+₹4,574.98 (2.75%)Rejected-AOC | L2 | Rejected-AOC L2 |
Tender Value
Refer Docs
EMD Value
₹3,078
Closing Date
18 Sept 2024, 12:00 pmClosed
Assistant Engineer IV
Lucknow division sharda canal Lucknow
Repairing and Maintenance of Chaudhary Charan Singh Auditorium at E-in-C Office, Cantt road, Lucknow. (Lot No.25)
2024_UPIDC_955168_25
02/AEIV/2024-25
Open Tender
Civil Works
Item Rate
30 days
Canal Colony Cantt Road
Please refer Tender documents.
2 documents required · 2 mandatory
₹0
₹3,078
2 Dec 2024
12 Sept 2024
18 Sept 2024
12 Sept 2024
18 Sept 2024
12 Sept 2024
12 Sept 2024 - 18 Sept 2024
Amount
P/F CPVC Pipe 75 mm. inner dia for drainage.
Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect.
Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
Rewinding of Celling fan with super enamel wire varnishing tasting,replacing ball bearing including erection,fitting etc. (i) Rewinding of ceiling fan with super enamel wire with erection & tasting excluding supply of down rod,complete rewinding of ceiling fan with super enamel wire all labour material and T&P (ii) Replacing ball bearing of ceiling fan with all labour material and T&P.
Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type
On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)
M/s Santosh Kumar Shrivastava
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .