CA NO. CWE SGNR-80 OF 2019-20 SPECIAL REPAIRS TO GOVERNMENT MARRIED ACCOMMODATION BLOCK NO. P-08 AT MILITARY STATION LALGARH JATTAN

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified Ceramic tiles 8 to10 mm thick (square/ rectangular) light shed polished, area of each tiles not exceeding 0.36 sqm, in floors etc. over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for Virified Ceramic tiles 8 to10 mm thick (square/ rectangular) light shed polished, area of each tiles not exceeding 0.36 sqm,on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles of size 450 x 300 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid over cement screed base laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as specified and directed by Engineer-in-Charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 10 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 on wall, finished even and fair including mixing of WPC in mortar complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be mearured and paid separately under respective item(s) of BOQ

M&L for rendering, 5 mm thick on brick work or concrete surfaces in cement mortar 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement : 1/2 coarse sand : 2 stone chipping 10mm nominal size) (using white cement in place or ordinary cement in the top laayer) in panels with groove all around as per approved pattern incuding scrubbing and washing, the top layer with bruses and water to expose the stone chippings complete all as specified and directed by Engineer-in-Charge. Note :- payment for providing groovs shall be made separately under respective item(s) of BOQ

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of wahed stone grit plaster as per approved pattern using wooden battens, naild to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of oil bound distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and two coats of oil bound distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for three coats of white wash on newly plastered surfaces incl preparation etc. complete on wall complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of white wash on old plastered surfaces incl preparation etc. complete on wall complete all as specified and directed by Engineer-in-Charge.

M&L for three coats of white wash on newly plastered surfaces incl preparation etc. complete on ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of white wash on old plastered surfaces incl preparation etc. complete on ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of cement base paint on newly / old plastered surfaces incl preparation etc. complete on wall complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick tiles in floor laid dry and pointed in cement morter complete all as specified and directed by Engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:5:10) using 40mm graded stone aggregate as filling of sunken floors/bottom and side of drain complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on brickwork or concrete surfaces in cement mortar 1:4 and finished fair and even including mixing of WPC in mortar complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be mearured and paid separately under respective item(s) of BOQ

Supply only integrated water proofing compound complete all as specified and directed by Engineer-in-Charge. Make:- Dr Fixit / Fosroc / BASF / STP

Material and labour for creating fillet caving 50x50mm with polymer modified mortar on the junction of slab and wall as per manufacture instructions, Material and labour Providing for applying two coats of two component (1 part Liquid: 2 part Powder) ready to use cementitious waterproof coating on properly prepared surface by brush having elongation of >50% for the applying water proofing treatment as per following and complete all as specified and directed by Engineer-in-Charge. (i) Applying 1st coat of two components modified polymer coating on horizontal and verticle surfaces. (ii) Provn of glasses fiber mess of 2x2mm with GSM 145 immediately on alone coating. (iii) Applying 2nd coat of two components modified polymer coating after 72hrs on horizontal and verticle surfaces. NOTE:- Complete treatment to be carried out by authorised applicatior of waterproofing manufacture. Make : Dr Fixit / Fosroc / BASF / STP

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm as in roof including cleaning surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for Roof treatment to RCC roof complete all as specified and directed by Engineer-in-Charge and as follows:- (a) Cleaning the roof surfaces thoroughly using wire brusehes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/plaster etc. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with WPC, finished even and smooth without using extra cement. (c) Providing one coat of approved bituminous primer @100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP membrane,(mineral finish) reinforced with non woven polyster fabric, by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by E-in-Charge. Make : STP / Dr Fixit / Pidilite / Texsa India Ltd / Tikitar Dansona / Bengal Bitumen Notes : (i) All joints and change in directions should be covered wih cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/as per site reqmt and cured well before laying membrane by torching. (ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only. The name of firm shall be got approved from GE before carrying out the work. (iv) The independent testing of membrane for technical parameters given in particular specifications shall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarnatee of treatment shall be for min 10 yrs reckoned from date of completion of whole work.

M & L for Lime concrete terracing as specified in roof (excluding bitumen tack coat) complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick brick tiles laid flat on lime concrete & joints grouted flush in cement mortar (1:3) bedded in 15mm th cement morter (1:6) mixed with 5% of crude oil by weight of cement on lime concrete complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 35 here-in-before but for except tiles complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for repair to damage RCC coloumns/Beam/Slab by using micro mortar and concrete in Following Stages complete all as specified and directed by Engineer-in-Charge.:- (a) Removing the mortar and loose concrete from RCC elements. (b) Cleaning the rusted reinforcements and applying rust removal. (c) Inserting the addl reinforcements in cape the coves sectional area reduction in more than 20 percent welding the reinforcement with existing area and supporting adequate on walls if reqiurd with grout. (d) Providing micro morter and concrete over bond coat to cover the reinforcements and slet surface. (e) Providing adequate from wave and scafolding if required. (f) Curing the surface. Note :- (i) Rust removal, bonding agent, grout, micro morter and concrete and related chemicals shall be of Dr Fixit/BASF and STP (ii) Work is to be got executed from authorised applications and company. (iii) Steel measured and paid separately

M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc. in apron complete all as specified and directed by Engineer-in-Charge.

M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment of soil under existing floors using emulsion @ one litrre per hole, 300mm apart including drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each complete all as specified and directed by Engineer-in-Charge.

S&F for powder coated aluminium frame / shutter for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete all as specified and directed by Engineer-in-Charge. Make of aluminium section : Jindal / Hindalco / NALCO

S&F for powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing exc 0.55 Kg/m (1.50 to1.80mm th) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (01 No) hinges type B-21 100 mm long (2 Nos) suitable handle (01 No) in each window shutterand necessary accessary as required complete all as specified and directed by Engineer-in-Charge. Note : Glass will measured and paid separately under respective item(s) of BOQ Make of aluminium section : Jindal / Hindalco / NALCO

S&F for Neoprene / EPDM rubber gasket complete all as specified and directed by Engineer-in-Charge. Note : Taken for other other than door/window shutter if required

M&L for 4.8 mm thick sheet glass, ordinary quality and glazing with aluminium snap beading of any size of glass in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engineer-in-Charge.

S&F for powder coated standard aluminium anodised grill size of mesh 75mm x 75mm and 8mm thick section using "U" channel 25x12mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for Fibre glass Reinforced plastic (FRP) door frame of required built in colour in three legged of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 30 mm thick glass fibre reinforced plastic (FRP) paneled doorshutter conferming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin,moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick FRP laminated for panels including fixing to frames complete all as specified and directed by Engineer-in-Charge.

Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified and directed by Engineer-in-Charge. Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.

S&F for 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces and the size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F for 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S&F for 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anosied and fixed type B-21 complete all as specified and directed by Engineer-in-Charge.

S&F for 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed by Engineer-in-Charge.

S&F for 125 mm long aluminium anodised handle, cast type complete all as specified and directed by Engineer-in-Charge.

S&F for 150 mm long extruded aluminium alloy handle, fabricated type anodised complete all as specified and directed by Engineer-in-Charge.

S&F for 100 mm long butt hinge, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F for 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engineer-in-Charge.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia fixed complete all as specified and directed by Engineer-in-Charge.

S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed by Engineer-in-Charge.

M&L for providing kitchen cabinet in required sizes at site made out of 18mm thick one decoative lamination sheet consisting of Careass 18mm thick PVC & provision of shutters made out of 18mm thick one side decoative laminated PVC sheet all required brackets 5.5 screws etc. The Panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as drawing and specification for PVC 18mm Celluca Ply (Prelaminated) for shutters complete all as specified and directed by Engineer-in-Charge.

M&L for providing kitchen cabinet in required sizes at site made out of 18mm thick one decoative lamination sheet consisting of Careass 18mm thick PVC & provision of shutters made out of 18mm thick one side decoative laminated PVC sheet all required brackets 5.5 screws etc. The Panels shall be fabricated using adhesive and screws where ever required. All the edges shal be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as drawing and specification for PVC sheet 18mm Prelaminated Stainless Steel for frame, partition, shelves etc complete all as specified and directed by Engineer-in-Charge.

S&F for telescopic drawer slides channel - zink plated complete all as specified and directed by Engineer-in-Charge. Make : Godrej or quivalent as approved by GE

S&F for stainless steel soft close crank hinges suitable size and shape as required complete all as specified and directed by Engineer-in-Charge.

S&F for magnetic catcher fixed with nut, screw and washer complete all as specified and directed by Engineer-in-Charge.

S&F for 40 mm dia, cupboard / drawers knobs with nut, screw and washer of brass, polished complete all as specified and directed by Engineer-in-Charge.

S&F for 100 mm extuded, barss handles, fabricated type polished for cabinet shutters complete all as specified and directed by Engineer-in-Charge.

S&F for stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 69 here-in-before but for fixing in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F for 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S&F for drapery rods, coloured, standrad quality, powder coated not less than 25mm dia with heads at both ends and middle support, rings, etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitrieous china wash down WC (Pedestal pattern) white and flush piple including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and directed by Engineer-in-Charge.

S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, seat and cover for water closet (European type) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china wash hand basin coloured Flat back of size 550x400mm, long screwed shank fly nut flange end including cutting for and pinning in ends of brackets in 1:3 CM including 32mm dia chromium plated waste coupling / trap complete all as specified and directed by Engineer-in-Charge.

S&F in repair bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS. Make : Model No : APR-ESS-101037, Make-JAQUAR or equivalent as approved by GE

S&F in repair bib tap 2-Way double handle with flange, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS. Make : Model No : APR-ESS-101041, Make-JAQUAR or equivalent as approved by GE

S&F in repair of Center hole wash hand basin mixer With 450mm long braided hoses system, brass (cast copper alloy) chromium plated, mixer for mixing hot & cold water suitable for wash hand basin, screwed down for iron pipe 15mm bore including taking down old valve any type complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of valve shall be as given in SSR or in relevant IS. Make : Model No. ASPIRE / SINGLE LEVER-APR-ESS-101011B of JAQUAR or equivalent as approved by GE

S&F in repair of Sink mixer with regular spout (W/M) , brass (cast copper alloy) chromium plated, mixer for mixing hot & cold water suitable for sink, screwed down for iron pipe 15mm bore including taking down old valve any type complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of valve shall be as given in SSR or in relevant IS. Make : Model No : Cat No 7355 of Prayag or equivalent as approved by GE

S&F in repair 2-way angle cock double handle with flages fancy type, cast copper alloy, chromium plated screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, size 15mm bore complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS. Make : Model No : Cat No - 7411 of Prayag or equivalent as approved by GE

S&F in repair angle valve/stop cock/stop valve fancy type, cast copper alloy, chromium plated screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, size 15mm bore complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS. Make : Model No : APR - ESS - 101053 of JAQUAR or equivalent as approved by GE

S&F in repair 15mm Concealed stop cock fancy type, cast copper alloy, chromium plated screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, size 15mm bore complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of concealed stop valve shall be as given in SSR or in relevant IS. Make : Model No APR - ESS - 101069 of JAQUAR or as approved by GE.

S&F in repair brass chromium plated overhead shower 70mm dia round shape single flow ( ABS Body chrome plated with gray face plate ) with rubit cleaning system with 240mm arm & flange including fixing to 15mm bore pipe complete all as specified and directed by Engineer-in-Charge. Make : JAQUAR Shower Model No : ALLIED Cat No - EOS - 491 or equivalent as approved by GE Make : JAQUAR, Arm Model No- ALE-536 A or equivalent as approved by GE

S&F in repair of wall mixer with "L" bend 115mm long full system brass (cast copper alloy) chromium plated, mixer for mixing hot & cold water suitable for bathing, screwed down for iron pipe 15mm bore including taking down old valve any type complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of valve shall be as given in SSR or in relevant IS. Make : Model No : APR-ESS-101273 of JAQUAR or equivalent as approved by GE

S&F in repair chromium plated fancy type health faucet with 1mtr tube & hook complete all as specified and directed by Engineer-in-Charge. Make : Prayag Model No-DROPLETS -Cat No-BEA-85 or equivalent as approved by GE

S&F in repair stainless steel chromium plated jet spray (butter fly or " L" bend) suitable for EWC including 1m tube and necessary nut bolts complete all as specified and directed by Engineer-in-Charge. Make : Make-Prayag Model No-DROPLETS -Cat No-BEA-17 (Butter fly type ) & BEA-18 (L- Bend type or equivalent as approved by GE

S&F in repair brass chromium plated Liquid soap dispenser including fixing to 15mm bore pipe complete all as specified and directed by Engineer-in-Charge. Make : Make-Prayag Model No-Chrome plated series -Cat no-493 or equivalent as approved by GE

S&F in repair corner glass shelf 200mm with Abs brackets complete all as specified and directed by Engineer-in-Charge. Make : Prayag Model No-ABS BRACKETS -Cat No-BEA-48 or equivalent as approved by GE

S&F in repair brass chromium plated PEG SET 6 including fixing to 15mm bore pipe complete all as specified and directed by Engineer-in-Charge. Make : Prayag Model No-DROPLETS -Cat no-BEA-30 or equivalent as approved by GE

S&F in repair chromium plated fancy type soap dish complete all as specified and directed by Engineer-in-Charge. Make : Prayag Model No-CANTABILE- PICASSO -Cat No-BA-05 or equivalent as approved by GE

S&F in repair stainless steel grating round or square 150mm size (minimum weight 100gms) complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

S&F in repair stainless steel kitchen plate rack made out with 1mm thick sheet of size 24" x 24" x 10" including taking down existing wooden plate rack complete all as specified and directed by Engineer-in-Charge. Make : Prayag Cat No-310 or equivalent as approved by GE

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed by Engineer-in-Charge. Make : Blue Star, Jayana or equivalent as approved by GE

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair tubular towel rail, Brass chromium plated 20 mm dia, 'D' type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Dismentling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F rotational moulded polythene water storage tank 1000 ltr capacity, tripple layers in white colour, vertical with closed top hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engineer-in-Charge.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repair ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball scewed for iron pipe and fixed, (Minimum weight 20 mm-210 gms), fixed in 20mm dia bore pipe complete all as specified and directed by Engineer-in-Charge.

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 105 here-in-before but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 107 here-in-before but for fixing only complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 107 here-in-before but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overalll as fixed along the cente line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) branch piece double (single Y) equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) bend any radius complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC (SWR) bend with access door any radius complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) floor trap, 75 mm dia with grating including jointing with solvent cement etc complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper /aluminium point wiring (light ,fan ,socket or power) complete incl fixture and fitting such as Switches, ceiling roses, pandents, regulators,sockets, light fitting etc removing materials to store for keeping in safe custody for taking credit(credit for above items shuold be made as per conditions separately) and making good distrubed surface of wall ,floors etc. complete all as specified and directed by Engineer-in-Charge.

Taking dwon MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down sub main wiring of any size / capacity and making good disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer-in-Charge.

M & L point wiring with PVC FRLS insulated unsheathed multistranded copper conductor drawn in and incl of size 1.5 Sqmm, 1100V grade in concealed PVC regid conduit, including provn of of 1.2 mm thich pressed steel sunken terminal boxes 60mm deep,suitable lenthand painted with red oxide primer for mounting switches, sockets, fan regulators covered with and including 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including 1.5Sqmm PVC insulated stranded copper conductor as earth continuity wire and connected to common earth dolly with copper lugs inserted in including MS boards complete heavy duty for housing switches, sockets, regulators, bell push etc, for One light/fan point controlled by one way switch 5 Amp. complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 121 here-in-before but for One bell/buzzer point controlled by one way switch 5 Amp complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 121 here-in-before but for One light point controlled by one two way switch 5 Amp complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 121 here-in-before but for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq mm size complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 121 here-in-before but for One 3 pin socket outlet, 5 Amps on independent board with other switches, with cables 1.5 sq mm size complete all as specified and directed by Engineer-in-Charge.

All as per item Srl item No. 121 here in before but for wiring with 4 sqmm multistranded cable and earth wire with copper conductor of size 4 sqmm for 15 Amps power point complete all as specified and directed by Engineer-in-Charge.

S & F switch piano ,flush type single pole, one way 5 amp complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 127 here-in-before but for 15 Amps complete all as specified and directed by Engineer-in-Charge.

S & F for switch piano flush button single pole 2 way 6 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs of socket outlet 2 in 1, 3 pin 5 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs of socket outlet 2 in 1, 3 pin 5 Amps and 15 Amps complete all as specified and directed by Engineer-in-Charge.

M & L for celling rose 3 pin/pvc/ polycarbonate isolated body complete all as specified and directed by Engineer-in-Charge.

S & F for LED light fittings 1 x 20 w, 230volts integral sleek polycarbonate LED channel with white acrylic cover incl making connection complete all as specified and directed by Engineer-in-Charge. Make : Bajaj Model BCLSD20WH or equivalent model of Crompton Greaves / Havells or as approved by GE

S & F for lamp holder insulated body with back plate for angle/batten fitting with LED of 09 watt complete all as specified and directed by Engineer-in-Charge.

S & F for bell push fulsh type 6 Amps complete all as specified and directed by Engineer-in-Charge.

S & F for bell AC 230 volts single pole complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs of stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required complete all as specified and directed by Engineer-in-Charge.

S & F for sheet metal enclosures for DBs double door type when MCBs to be used single pole & nuteral 12 ways complete all as specified and directed by Engineer-in-Charge.

S&F for MCB SPN 63 Amps, 'B' Curve, 240 Volts complete all as specified and directed by Engineer-in-Charge.

S&F for MCB SP 6 to 40 Amps, 'B' Curve, 240 Volts complete all as specified and directed by Engineer-in-Charge.

S&F for MCB SP 63 Amps, 'B' Curve, 240 Volts complete all as specified and directed by Engineer-in-Charge.

S&F for PVC blanking plate complete all as specified and directed by Engineer-in-Charge.

S & F for submain wiring with two single core cables PVC FRLS insulated unsheathed 6 Sqmm stranded copper conductor drawn in and including PVC conduit with and including PVC insulated 6.0 Sqmm stranded copper conductor cable as earth continuity conductor and connecting complete all as specified and directed by Engineer-in-Charge. Note : PVC cables two single core and one single core of sizes as mentioned will considered as one unit

S & F for submain wiring with two single core cables PVC FRLS insulated unsheathed 10 Sqmm stranded copper conductor drawn in and including PVC conduit with and including PVC insulated 10.0 Sqmm stranded copper conductor cable as earth continuity conductor and connecting complete all as specified and directed by Engineer-in-Charge. Note : PVC cables two single core and one single core of sizes as mentioned will considered as one unit

S & F for sheet metal enclusure single pole and nutral with 02 pin and earth plug and socket complete with 01 singel pole 20 amps 240 volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to galvanised iron 4mm GI wire (8 SWG)thick fixed by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia upto 3m height above ground level and water pipe 20mm dia GI medium grade with socket and plug 30 cm above ground level including earthwork, PCC chamber in PCC (1:3:6) type C-2 using 40mm stone aggregate, cast iron cover, wire meah etc all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009 complete all as specified and directed by Engineer-in-Charge. Notes :- (i) 20 mm dia GI pipe for watering to be provided with a socket and plug and should be 30 cms above ground level. (ii) GI wire upto DBs earth connection is included in this item. (iii) GI pipe 15 mm dia protection pipe shall be provided upto Ground level.

M&L for taking down exhaust fan 300mm sweep single phase 240 volts 50 Hz and refixing the same after servicing, repairing and repainting in all electrical connection, fastners of required size complete including louvers made out of GI wire mesh fixed in wooden batton as frame of adequate size and fixed outside building complete all as specified and directed by Engineer-in-Charge

S & F for fresh air fan 225mm sweep 240 volts 50 Hz plastic body complete with louvrs including making arrangement for fixing in walls, holes or windows / ventilation complete all as specified and directed by Engineer-in-Charge.

M & L for taking down Hot water heater (Geyser) storage type AC 230 volts of cap 50 ltrs and refixing the same after repair, servicing and painting including spare parts required at site incl making connection and 02 Nos PVC connection pipes and painting the same complete all as specified and directed by Engineer-in-Charge.

S & F for VTPN DB 3 phase and neutral 4 ways double door as MCCB 125 Amps 16 KA IP 43 Protection as incomer with bus bar rating 200 Amps vertical type dust and vermin proof complete all as specified and directed by Engineer-in-Charge.

Supply and fix for temper proof energy meter 10-60 amps single phase 240V AC duly sealed and connection in existing meter board complete all as specified and directed by Engineer-in-Charge. Make : HPL CAT Part No. TPPL 1810000000OC No. or equivalent in L&T / Secure or as approved by GE

M & L for taking down ceiling fan any sweep single phase 240 volts 50 Hz and refxing the same incl all electrical connection, rubber real with clamp of required size complete all as specified and directed by Engineer-in-Charge.

M & L for repair door hindges of MS housing of size 100x.90 m including necessary welding and painting panel with two coats of synthatic enamelled paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. -------------------------------------------------------------------------------------------------------------- Note : A sum of Rs. 58,190.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 40 & 41(R) (Schedule of Credit) of Tender document

ram rattan dass aggarwal