SPL REPAIR OF P-396 (1, 2, 3, 4) TYPE-II (CIV MD ACCN) AT NIRMAN VIHAR AREA UNDER GE (S) JAIPUR AT JAIPUR MIL STN

Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for Raking out joints/pointing to stone masonary work in walls or to bricks on edge in floors, surface channels, roofs, etc.

M&L for rendering 15mm thick on stone masonry surfaces in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces in CM 1:4 and finished even and smooth with using WPC complete all as specified and directed. (Note : WPC will be paid separately.)

M&L for rendering 10 mm thick in cement mortar (1:3) on any face of ceilling or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified.

M&L for preparing newly plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over a coat of primer including 1mm thick wall care putty to make smooth the undulated surfaces complete all as specified and directed.Note : the surface should be even and smooth after applying the wall care putty irrespective of number of coating applied and as per direction of Engr in charge/GE

M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and apply three coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior acrylic emulsion paint by mechanical means over a coat of primer and over 1 mm thick wall care putty complete all as specified and directed. Note : the surface should be even and smooth after applying the wall care putty irrespective of number of coating applied and as per direction of Engr in charge/GE

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness laid dry or laid dry and pointed in floor, aprons or as in slabs complete all as specified and as directed.

M&L 25 mm thick for PCC Flooring using cement concrete 1:2:4 type B-0 using 12.50 mm graded aggregate below floor tile as in levelling course

M/L Non skid ceramic joint free coloured tiles 7-8 mm th (square or rectangular)area of each tile exc 0.06 SM but not exc 0.11 SM in floors etc.. Set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for double charged vitrified ceramic coloured tiles (of approved coloured shade) of size 600x 600mm, 9 to 10 mm thick in floor, set & jointed in neat cement slurry including a layer of screed bed 15mm thick 1:6 and pointed in coloured cement to match the shade of tiles over cement screed bed all as specified

All as per item No. 14 but on vertical surfaces such as skirting, dados and riser etc including a layer of screed bed/backing coat 10mm thick 1:4 all as specified.

M&L for glazed ceramic coloured tiles 300 x 200 x 7 mm / 450 x 300 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M&L for Granite 18 to 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed/back coat in cement mortar 1:4 complete all as specified and as directed.

Rounding/moulding and poishing to edges of stone slab ( granite) two edges such as in cooking platform

M& L for Machine cut kota stone slab flooring 20-25mm thick over cement over 15 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including notching/nosing/easing complete all as directed.

- Ditto- all as per ser item No above but in skirting including 10mm back coat in CM 1:4 complete all as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) and removal of rubbish from site complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, copings, bed plate, plinth courses, roof kerbs or mud stops rounded or chamfered on edges including necessary form work complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving n exc 15 cm thick (below above ground level) complete all as specified and directed.

M&L Cement concrete type D2 1:4:8 as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm tickness , M-35 grade, set, jointed over 25 mm thick sand cushoning all as directed by Engineer-in-Charge.

M&L for chequered tiles cement concrete tiles 20x20x25cm thick, set jointed & pointed in neat cement slurry in floors with grey cement & pigment over 20mm thick screed bed in cm 1:6

Cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in plinth protection, 75mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge and as specified. Note:- 10mm wide and 75mm deep joints shall be made at 3 mtr interval and at each corner the same shall be filled with using bitumen 85/25 and sand in the ratio 1:3 complete all as directed.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed

Taking down existing roof tiles/PCC/any type of treatment on roof/terrace of any description complete all as specified and directed.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0,( 1.2.4) using 12.5 mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement.

M&L rendering 10mm thick in cement mortar (1:3) on concrete surfaces to receive water proofing treatment finished even and smooth complete all as specified.

Supply only liquid water proofing compund

S&F fiber reinforced UV resistant elastomeric liquid applied waterproofing & heat reflective coating with acrylic polymers and polyester/glass fibers after scraping and properly cleaning the surface to remove loose particles with wire brushes complete or as directed over a coat of primer as per manufacturers instr.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar or cement lime mortar

M&L for brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thickwalls built in ®CM 1:4 complete all as specified and as directed

M&L for walling of random rubble uncoursed stone masonry, well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

Taking down existing chowkats or frames (without taking out shutters ,from the frame) n exc 1.5 SqM

Taking down door chowkhat or frame exe 1.5 sqm but n exc 4 sqm shutter (without taking off shutter from the frames)

S&F 40mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

S& F Factory made, 35mm thick, 2nd class hard wood (Hollock), glazed and skelton shutters, but divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars,(door consist 4 to 6 panels) prepared to receive glass/ gauge etc(without sash bar) edges of framing plain , chamfered or rounded fitted with cut and mitered beads for securing glass etc size member of shutters as specified in SSR Pt I ,section 8, clause 8.24 (a) of MES Schedule Part-I in Section-8, complete all as specified.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

M&L powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. stainless steel screws, all complete including making good disturbed portion with the cement mortar 1:4 or providing PCC 1:2:4 type B0 in sill of opening complete all as specified and directed by Engineer-in-Charge.

M&L powder coated aluminium window and ventilator shutters, fixed/side hung or sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified & as directed.

S&F 4.80mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares exc 0.50 Sqm in each pane complete all as specified.

S&F aluminium expanded metal mesh of weight exc.0.55 Kg/Sqm as support to SS wire cloth over guazed door shutter complete all as specified and as directed

S&F snake guard (door seal aluminium plate with rubber beading ) for door complete all as specified and directed.

S& F stainless steel sliding door bolt with hasp and staple and fixing clips of sheet , cast or extruded section , and fixing bolts and sliding bolts of extruded sections and fixed length of bolt 300 mm complete all as specified and as directed.

S & F stainless steel handles, fabricated type, size of handle 200 mm complete all as specified and as directed.

S&F stainless steel 200mm long barrel tower bolts of extruded section complete all as specified and as directed.

S&F stainless steel 150mm long barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100mm Butt hinges, stainless steel hinge pin,anodised and fixed, with SS screw of good quality complete all as specified and directed

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate inclunding fixing to existing steel chowkhat with welding or fixing over wooden frame complete all as specified and directed

S & F 100 mm long double leg door stopper of stainless steel body with two number rubber shoes complete all as specified and as directed.

Supply & fix in repair stainless steel curtain rail fancy type 20-25mm dia all as specified and directed.

Supply & fix in repair fancy type stainless steel brackets for curtain rod with SS screws complete all as specified and directed

Supply & fix in repair fancy type SS side holder/ bulb for20-25mm dia curtain rod all as specified and directed

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wirean d average width of aperture 1.40mm and fixed with stainless steel wire staples ® complete all as specified.

M&L Squatting pan orrissa pattern vitreous china white of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore sand cast cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed in repairs, complete all as specified.

S & F in repairs PVC valve less symphonic action type flushing cistern low level with all internal fittings including flush pipe with bend , 450mm long PVC connection and connected to WC complete all as specified and directed.

S&F Rotational moulded polyethylene 1000 ltrs water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling old unserviceable water tanks and removing to store complete all as specified and as directed.

S&F in repair wash hand basin, flat back 550x400mm vitreous china (white) including PTMT wastecoupling of 32mm bore size, waste pipe PVC of 32mm bore, PVC connector 450mm longs with angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified.

S & F in repair kitchen sinks made of stainless steel sheet 1mm th of grade SS-304 incl washer, brass sink coupling, waste pipe, bowl size 495 x 420 x160 mm fixed in kitchen granite top incl cutting granite/ marble of cooking platform

S & F in repair Plate rack of size 900mmx750mmx250mm fabricated out of 1mm thick stainless steel sheet fixed in repair complete all as specified and directed.

M&L in repair for 100mm dia Cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F in repairs 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

S&F in repair long body bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type chromium plated of 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair angle/Stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated fancy type screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair 5-6 inches overhead Brass chromium plated shower rose incl shower arm of 24 inches with 15mm bore with or without swivel joints, any size, including fixint to steel pipe or union complete all as specified and directed.

Supply and fixed in repairs CP brass kitchen sink mixer with pipe swinging spout wall mounted model with connecting legs & wall flanges including all accessories as per manufacturer complete all as specified and as directed.

Supply and fixed in repairs CP central Hose Basin Mixer long shank fancy type 15 mm bore complete all as directed.

S&F in repairs brass CP Wall Mixer for mixing hot & coldwater with provision of shower secewed down for iron pipe complete all as specified and as directed.

S&F in repair Soap dish, stainless steel of good quality all as directed

S&F in repairs brass CP towel rail 60 cm long square complete all as specified and directed.

Dismantling of 75/100mm bore PVC soil/ waste pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 75 mm bore of pipe etc complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed

S&F PVC (SWR) bends any radius of 110 mm bore with out access door complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or un equal of 75 mm bore of pipe complete all as specified and directed

S&F PVC (SWR) bends any radius of 75 mm bore with out access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed.

M&L PVC (SWR) floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410-W (GdeE- 250) quality Acomplete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

M&L for special treatment of sunken portion of WCs and Bath room as per following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:4 finished even and smooth complete all as specified and applying two coats of Dr Fixit URP over plaster in sunken portion (The surface after painting one coats shall be allowed to dry of 6 hours before next coats) as per manufacturer direction complete all as specified and as directed. Stage 3:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd and applying two coats of Dr Fixit URP over plaster in sunken portion (The surface after painting one coats shall be allowed to dry of 6 hours before next coats) as per manufacturer direction complete all as specified and as directed Stage 4:- All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 5:- Making holes in wall and fixing 600mm- to 800mm long 40mm dia GI spout for draining the surplus water if any.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

Providing and fixing factory made PVC cup boards/ Shelf / Partition of required size consisting of panel of 18mm thick Celuka PVC Ply and for supporting the hold of Shelf/ Partition and shall provided 3edges in size 18mm x18mm as per required length. The front side of the edge visible in the front of the shelf/ Partition to be edge lipped by 18mm width x 1mm thick PVC sheet using solvent cement etc. complete as direction of Engineer-in-charge, manufacturer's specificaton and drawing.

S & F 5mm thick pvc panelling in back of cup board, one side prelam make “ Rajshree” fixed with screws to make cup boards, complete all fitting arrangement fixed in repair.

S & F Continuous (piano) hinges,width of flaps 30mm (when open) mild steel, bright finish or electrogalvanised complete all as specified and as directed.

Supply and Fix magnetic catcher of good quality made up of plastic and sheet metal plate of suitable size for fixing in cupboard or PVC shutter complete all as specified and as directed.

S&F 125 mm oval shape SS handle fancy type bright finish or as approved complete all as specified and as directed.

S&F in repair stainless steel plain wire basket of approved quality of size 520 X 485 X 100 mm complete all as specified and as directed.

S&F in repair stainless steel thali basket of approved quality of size 520 X 485 X 100 mm complete all as specified and as directed.

S&F in repair stainless steel perforated cutlery basket of approved quality of size 520 X 485 X 100 mm complete all as specified and as directed.

S&F in repair basket/trolly soft close telescopic channel 50 cm long and 50mm width extruded MS galvanised with roller having ball bearing including drilling over stone/ply and PVC board etc complete all as specified and as directed.

M&L for demolition and breaking up drain pipes salt glazed ware set in CM of 150 mm dia bore pipe complete all as specified and as directed.

M&L for concrete bed to 150mm dia bore drain pipes including packing under & haunching against the sides of pipes after they are laid & tested; in PCC (1:4:8) type D2 complete all as specified and as directed.

M&L Double Wall Corrugated (DWC) HDPE pipes in trenches & jointed as specified of 100mm dia complete all as specified and as directed.

M&L Double Wall Corrugated (DWC) HDPE pipes in trenches & jointed as specified of 150mm dia complete all as specified and as directed.

Dismantling posts or struts embedded in Concrete, brick work, masonry, etc.(wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground

S & F mild steel work as in fencing posts/ flat iron as in straps to hold chain link fencing incl. cutting tops to shape as directed , drilling holes, notching for wire etc.,flat iron fillets (for securing wire mesh etc.)incl. all necessary drilling, bolting or riveting etc. and similar work complete all as specified.

Supply only chain link MS galvanised fencing any size or type or as approved by Engineer in Charge

Fixing only Chain link fencing incliding line wire any mesh and type to any type of standards, rails, straining bolts etc includign provision of binding wire

Supply only mild steel screw bolts (machine made) with hexogonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexogonal or square nut 10 to 12 mm dia and exc. 5 cm and nexc. 10 cm long complete all as specified and as directed.

MS round bars 10 mm dia as in round/Sag bars in chain link fence cut to length bent to shape and making hooks complete all as specified. Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde - E-165)

Taking down carefully surface aluminium or copper point wiring with PVC casing or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets, light fittings etc and making good disturbed surfaces of walls, floors, etc all as directed.

Taking down celing fan of any size, sealing cable end , dismantling blade and removing fan regulator any type & size and keepinig in safe custudy for reuse/deposite to MES store all as specified and directed by Engr-in-Charge .

Refixing of ceiling fans after required minor repairs such as replacement of capacitor,connector block, split pin nuts bolts etc and connecting up including provisioning of cable from ceiling rose or connector to fan and painting of ceiling fan complete in situ with synthetic enamel paint by spraying including filling cavity with filler , one coat after cleaning or dust etc complete all as directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes for mounting switches, sockets, fan regulator as required for one light point controlled by one 6A switch.

All as per item No. 128 here-in-before but one fan point controlled by one 6A switch

All as per item No. 128 here-in-before but one Exh fan point controlled by one 6A switch

All as per item No. 128 here-in-before but one light point controlled by two, two way 6A switch.

All as per item No. 128 here-in-before but One socket outlet 6 amp controlled by one 6A switch on indepdendent board.

All as per item No. 128 here-in-before but One bell point controlled by on bell push button.

All as per item No. 128 here-in-before but One socket outlet 6 amp controlled by one 6A switch on same board with other switches.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame for one socket point 16 Amps controlled by one 16 switch on indepdendent board. Note :- (a) The cost of Modular Metal flush box & modular cover plate colour and size as required at site and cutting chases in stone masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate and the make of modular plate shall be of the same brand as per Switch/Socket accessories (b) Modular switch/socket accessories shall be measured & paid separately in respective item

S&F angle holder 6A, 240V insulated polycarbonate body with back plate complete.

S&F switch modular 1 way 6/10 Amps, 230 volts, 1 module.

S&F modular socket 6/10 Amps, 2/3pin combined 2 module AC 230 volts.

S&F modular switch 1 way 16/20 Amps, 230 volts, 1 module.

S&F modular socket 6/16 Amps, 2/3pin combined 2 module AC 230 volts.

S&F modular fan regulator 120 watts, 2-module AC 230 Volts.

S&F switch modular 2 way 6/10 Amps, 230 volts, 1 module.

S&F Modular bell push 6A 1 module.

S&F musical bell, AC, 230 volts, single pole.

S&F ceiling rose 3 pin(phase,neutral and earth polycarbonate body complete.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper cable of size 2 x 6 sqmm drawing into and including rigid non metallic PVC conduit concealed in wall, medium grade not less than 20mm dia ISI marked ivory colour with all conduit fitting and fixing accessories and 6 sqmm FRLS multistranded copper conductor cable as continuous earth wire complete all as specified and directed (Note1 :- 2 runs of 6 sqmm copper wire and 1 run of 6 sqmm copper earth wire alongwith PVC conduit shall be measured as 1 unit. Note2- Rate of Cutting chasing of exixting wall and making good of disturbed surface for concealed conduit shall be included in this item

S&F 20 amp, single pole and neutral socket outlet with 2 pole and earth, metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with chained metal cover for socket outlet with and including one number single pole 'C' series MCB 20 amp as required.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 40 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.Add Note:- Excavation for earthing to be done manually and Earth resistance below 3 Ohm should be obtained after measurement for every pit

S&F in replcement MCB distribution board, powder coated, TPN , 415 volts, 4 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 200 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F MCB distribution board, powder coated, SPN , 240 volts, 8 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 200 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required .

S&F MCBs SP of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp.

S&F MCBs SPN of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Double pole 10 to 32 amp.

S & F in repair MCB Tripple pole neutral(TPN) 'C' series 100 Amps,10 KA, ISI marked, for inductive load connected through cable lugs of suitable size complete all as specified and directed .

S&F in repair LED (1.2M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having lumen not less than 2200 complete all as specified and directed.

S&F in repair LED(0.6M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having lumen Upto 100 lumens per watt complete all as specified and directed.

S&F LED 35 watt building security light smartbrite aluminium PDC housing with IK 07 protection PC glossy diffuser duly prewired connection having a nominal system lumen output of efficiency 100 lumens/ watt light watt and total power consumption not more than 35 watt including driver. It has a rated IP 66 with 5 KV inbuilt surge protectione. (Note:- Bracket along with screw to fix on wall/surface duly painted by silver colour paint will be included in above quoted rate.)

S&F PVC fresh air fan 200/250 mm sweep,230 V with louvers, fan motor and accessories complete including making connections.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete as specified and directed by Engr-in -Charge.

S&F in repairs Bulk Head light environfriendly ultra modern energy saving surface mounted decorativeoval bulk head edge lit LED luminaire comprising of High brightness LED Lamp.

S&F ceiling fan type 1200 mm sweep 50 Hz AC 230 volts, BEE 5 star rated in white colour with fan motor, blade set , 0.45 mtr down rod, canopy.Make:- cat part Havells ES-50, CG, Orient

Schedule of Credit amounting to Rs 49983.00 to be deducted offline at the time of Acceptance of Tender.