PROVN OF TWO NOs TRANSFORMER (66/11) KV AGAINST BER 66 KV TRANSFORMER UNDER GE (EAST) FEROZEPUR

Amount

Note:- Please refer Sch 'A' notes on Srl Page No 14 to 16 (A) on tender documents.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep for laying of cable, pole foundation, etc including taking out old brick cable protection cover and getting out forming bottom surface to required gradient, complete all as specified and directed.

Returning, filling in, soft/loose soil including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified and directed.

Removing excavated soil to a distance not exc. 50 meter and depositing where directed at a level not exc. 1.5 meter above the starting point, complete all as specified and directed.

Material & labour for Precast reinforced cement concrete cable cover factory made class HV, type-I, flat, size 300mm x 180mm x 40mm for HT cable ISI marked, laid flat across the cable, complete all as specified and directed.

Material & labour for sand cushioning using river fine sand for the underground cables in trenches/existing cable trenches, in layers of 8cm thickness before lying the cable and 15cm thickness after laying and stretching cable punned down to 18 cm complete all as specified and directed. Note:- Only punned thickness shall be measured for the purpose payment.

Supply, install, testing and commissioning step down Power Transformer of capacity of 5 MVA capacity, 3 Phase, 66/11 KV, 50 Hz, ONAN Cooled, Double Limb Copper wound core type for outdoor application mounted on rails with Wheels, vector group YNyno (star/star), as per IS 2026 with latest amendments, Onload tap changer(OLTC) with RTCC Panel and Automatic Voltage Relay for OLTC from (+) 5% to (-) 15% in step of 1.25%, HV side 66 KV bare bushing termination and for LV side 11 KV bushing termination cable box incl first filling of transformer oil (IS 335 of 2018) with following specifications fitting and accesories, complete all as specified and directed. (A) The Rating and General data of the Transformer:- (i) Type of transformer- ONAN Cooled 5 MVA Transformer 3 Phase 66/11KV, Step Down Power transformer, Double Limb copper Wound core Type for outdoor Applications mounted on Rails with Wheels. (ii) Type of Windings- (a) HV-Disc type with Static end rings at both ends with uniformly insulated. (b) LV-Continious disc type with Uniformaly insulated. (iii) Winding Connection for 3 Phase Transformer:- HV- Star/ LV- Star(YNyno) (iv) Max. Value of the percentage impedence at the (Normal working) at the normal/principl tap position at 5 MVA IS(Tol.)- 11.6% (v) Overloading capacity of transformer:- (a) Continious overlaoading - As per IS-6600 (b) Short TIme Overloading - As per IS- 6600 (c) Emergency Overload - As per IS -6600 (vi) OLTC - A seprate tapped winding on the primary winding to give rated secondary voltage for variation in primary voltage from (+5%) on maximum and (-15%) on minimum in steps of 1.25%.OLTC shall be of Minimum 72 KV voltage class and shall have maximum rated high current 300 Amp, Short circuit withstand current as per OEM Recommendadation.

(vii) Maximum No load loss in KW at 100 % Rated voltage IS (Tolerance) Shall not exceed 6.5 Kw. (viii) Maximum Copper Loss at 75 Deg temp rated voltage IS (Tolerance) Shall Not exceed 34 Kw. (ix) Total Loss IS(Tolerance)-Shall not exceed 40.5 Kw. (x) Insulation Medium-Transformer Oil as per IS 335 of 2018. (xi) Earthing Terminal as per OEM. (xii) Insulation Level for Windings- (a) Winding BIL - HV - 325 KVp/140 kVrms (b) Winding BIL - HV-N - 325 KVp/140 kVrms (c) Winding BIL - LV - 75 kVp/28 kVrms (d) Winding BIL - LV-N - 75 kVp/28 kVrms (xiii) Max Temp rise of Oil - 45 Deg over Ambient. (xvi) Maximum Temp rise of winding - 55 Deg over Ambient. (xv) Terminal Arrangement - (a) HV -Bare Bushing (b) LV - Cable Box (xvi) Efficiency at 75 Deg at Unity PF- Not less than 99.2% at all load and Efficiency at 75 Deg at 0.8 Pf not less than 99% at all load. (xvii) Paint shade:631 of IS: 5 (Epoxy) (B) Accesories:- (a) Buchloz relay with alarm and trip contact-01 No (b) Oil Temparture indicator 6 " dia with alarm & trip contact -01 No (c) Winding Temparture indicator 6" dia with alarm & trip contact -02 No (d) Oil Surge Relay -01 No. (e) Marshalling box(IP-55)-01 No. (f) Main Tank - 01 Nos (g) OLTC with all accesories as per OEM -01 Nos. (h) RTCC Panel with automatic voltage relay with accesories as per OEM-01 No.

(C) Fittings:- (a) Conservator tank with oil filling hole and drain plug (b) Megnatic oil gauge with minimum level marking fitted in conservator tank & oil level in for OLTC as per OEM recommendation -01 Nos (c) Thermometer pockets-02 Nos (one for OTI & one for WTI) (d) Silica gel breather -02 Nos ( for Main Tank and OLTC Tank) (e) Lifting lug-04 Nos (f) Earthing terminal as per OEM. (g) Bi-directional Roller space between roller as per existing transformer -04 Nos (h) Anodized aluminium rating and diagram plate -01 Nos (j) Bottom drain-cum filter valve-01 No (k) Pressure relief device, with trip contact-02 Nos(One No for OLTC and One for Main Tank) (l) Radiator-01 Set (m) Jacking pad-01 Set Note:- 1. The errection of transformer shall be done under the supervison of manufacturer auth rep & certificate to that effect shall be submitted by the contractor duly signed by manufacturer auth rep & Engineer-in-charge. 2. The transformer shall be fitted on existing platform. Necessary modification/repair if any required as per recommendation of OEM is under scope of work and cost thereof is deemed to be included in quoted rates by the contractor. 3. The make of Power Transformer will be approved by the accepting officer. Subsequently detailed technical specification of Power Transformer, OLTC and all other mounting, accessories of power transformer along with their GAD will be submitted through CWE for approval of the Accepting Office before procurement action. 4. Pre dispatch inspection at the factory premises of OEM shall be carried out by nominated rep of Accepting Officer. The arrangement for pre dispatch factory inspection & testing of Power Transformer will be responsibility of the contractor & cost thereof is deemed to be included in quoted rate.

5. Pre-commisioning of power transformer and 66 KV Network by state electricity board /PSPCL shall also be got carried out within overall cost quoted. 6. Pre -commisioning & Testing shall be carried out by SEI from HQ CE WC within overall cost quoted. 7. All parts and accessories, fittings necessary for efficient operation of 66/11 KV Power Transformer shall be deemed to be within the scope of specifiction wheather mentioned or not specifically mentioned here in. 8. Power transformer should be manufactured, designed & supplied by OEM only. Power transformer from the channel partners not acceptable.

Supply, installation, commissioning & testing, Out door type SF-6 circuit breaker, three pole operation as per IEC -62271-100, complete with all accessories including SF6 gas suitable for 66 KV system volt 3 phase, 50 Hz and of the following technical specifications complete all as specified and directed. (a) Rated Voltage :- 72.5 KV (b) Rated normal current : 2000 Amps (c) Rated power frequency withstand voltage : 140 KV (d) Rated lightning impulse withstand voltage : 325 KV. (e) Rated circuit breaking current min : 31.5 KA. (f) Making current : 79 KA (g) Short time current : 3 seconds. (h) Minimum creepage distance phase to earth : 25mm/KV. (i) Number of trip coil- 02 nos (j) Number of closing coil - 01 no. (k) Rated closing /tripping voltage : 220 V DC (l) Minimum creepage distance across open breaker : 25mm/KV. (m) Operating range for closing coil and spring charging motor : 85% to 110% rated voltage. (n) Operating range for trip coil : 70% to 110% rated voltage. (o) All other standard components required for the functioning of the SF6 breaker as per OEM Recommandation. Make : ABB/CG Power and Industrial Solution Limited or equivalent.

Note:- Rates quoted by bidder are deemed to include following : (i) The SF6 breaker shall be fitted on existing structure. Necessary modification/repair if any required as per recommendation of OEM is under scope of work and cost thereof is deemed to be included in quoted rates by the contractor. (ii) The make of circuit breaker (SF6) will be approved by the accepting officer. Subsequently detailed technical specification of circuit breaker (SF6) and connected ckt diagram alongwith their GAD will be submitted through CWE for approval of the accepting officer before procurement action. (iii) Pre dispatch inspection at the factory premisses of OEM shall be carried out by nominated rep of Accepting Officer. The arrangement for pre dispatch factory inspection & testing of circuit breaker (SF6) will be responsibility of the contractor & cost thereoff is deemed to be included in quoted rate. (iv) SF-6 circuit breaker should be manufactured, designed & supplied by OEM only. SF-6 circuit breaker from the channel partners not acceptable.

(u) Diffrential relay with suitable accesories as per OEM for transformer protection. (v) Numerical type transformer backup protection relay(non- directional)- 01 Nos.(Make:- ABB, Siemens, micom) (w) Feeder protection and control relay numerical type having MOD Bus +IEC61850 communication protocol on RS485 serial port & 1 No. Rear RJ45 Ethernet Port, Supply 48-250 VDC, 100-240 VAC, Model- REF615 of ABB make or equivalent model of Siemens. (x) Control /switch for isolator, Transformer, SF6 circuit breaker. Make : ABB/CG Power and Industrial Solution Limited or equivalent. Note:- Rates quoted by bidder are deemed to include following:- (i) The control and relay panel shall be fitted on existing platform. Necessary modification/repair if any required as per recommendation of OEM is under scope of work and cost thereof is deemed to be included in quoted rates by the contractor. (ii) The make of control and relay panel will be approved by the accepting officer. Subsequently detailed technical specification of control and relay panel and connected ckt diagram alongwith their GAD will be submitted through CWE for approval of the accepting officer before procurement action. (iii) Pre dispatch inspection at the premises of OEM shall be carried out by nominated rep of Accepting Officer. The arrangement for pre dispatch factory inspection & testing of control and relay panel will be responsibility of the contractor & cost thereof is deemed to be included in quoted rate. (iv) Control relay panel should be manufactured, designed & supplied by ORM only. Control relay panel from the channel partners not acceptable.

Supply, installation, testing and commissioning heavy duty metal oxide gapless outdoor type Lightning Arrester of rated voltage 66 KV, for use with effective ground neutral system with insulating base including surge monitors for 66 KV system 50 Hz for line and transformer 66 KV with all accessories on existing structure as under complete all as specified and directed:- (a) Nominal System voltage : 66KV (rms) (b) Highest system voltage 72.5 KV (rms) (c) Nominal discharge current - 10KA (d) High current impulse withstand(4/10 ms) - 100 KA peak (e) System BIL - 325 kV (peak) (f) Line discharge - Class 3 (g) Minimum creepage distance -1815 mm. (h) External insulation requirement as per IEC- 60099-4. (i) Lighting Impulse withstand voltage (dry) - 325 kV(peak) Make: Oblum/ LAMCO/ CGPISL or equivalent make.

Supply, installation testing and commisssioning polymeric motorized isolator suitable for nominal voltage 66 KV 50 Hz, 3 phase system of capacity 800 Amps continous current completewith the followingspecifications complete all as specified and directed:- A. INSULATION LEVEL (a) Impulse with stand voltage (i) Aginst Ground : 340 KV(Peak) (ii) Acrosss the open ends of the phase : 345 KV(Peak) (iii) Between Phases : 345 KV(Peak) B. Power frequency with stand voltage (ba) Against Ground (i) Dry : 140 KV(rms) (ii) Wet : 140 KV(rms) (bb) Across Open Contact (i) Dry : 145 KV(rms) (ii) Wet : 145 KV(rms) C. Minimum clearance in air (min) : 2000 mm (a) Between Phases : Min 762 mm (b) Between live part and earth : 762 mm D. Short time current rating (i) for 1 Sec : 40 kA (ii) for 3 Sec : 25 kA D. Rated peak short circuit current : 63 KA E Temperature rise correspondong to:- (a) At Maximum continious current rating at 50 deg ambient - 65 Deg C F. Design & construction (a) Nos of insulator per pole : 03 (b) Nos of breaks per pole : 02

(c) Type of closing /opening mechanism : Horizontal (i) Material : Hard drawn electrolytic copper or its Alloy (e) Moving contact material : Hard drawn electrolytic copper or its Alloy (f) Contacts support Terminal connector's clamp body alloy composition : LM-9 G. Turn & twist mechanism (i) Material of moving contact : Electric grade copper (ii) Material of fixed contact : Electric grade copper Strip. H. Type of interlock : Mechanical & electrical J. Down pipe material : GI Pipe K. Solid core type insulator L. Terminal connector (i) Alloy composition : AL LM-9 (iii) Termperature rise : As per IS -9921 M. Opeating mechanism : Motor drive & manual both. Make :- Rashtriya electrical & Engg Corp, Jaipuriya Brothers Electrical Pvt Ltd or Equivalent Make.

Supply, install, testing and commissioning 4 core outdoor type 72.5KV, 31.5KA for 1 sec, Class 'A' (Oil Impregnated Paper Type cooled), hermetically sealed, wound primary type, 4 core live tank type current transformer of ratio 75-150/0.577-1-1-1 Amp, complete all as specified and directed. (i) Highest System Voltage (phase to phase): 72.5KV. (ii) Core-I BURDEN (VA) - 30, ACCURACY Class 0.2 (iii) Core-II BURDEN (VA) - 30, ACCURACY Class 0.2 (iv) Core-III BURDEN (VA) - 15, ACCURACY Class 5P (v) Core-IV BURDEN (VA) - -- ,ACCURACY Class PX (a) Knee point voltage @ highest tap : 250 V (vi) Frequency : 50Hz (vii) STC : 31.5kA for 1 sec. (viii) Voltage level : 66KV, effectively earthed system (ix) Power frequency (wet & dry) withstand Voltage on primary Winding - 140 kV(rms) (x) Power frequency withstand Voltage on Secondary Winding - 3 kV(rms) (xi) Lighting impulse withstand voltage - 325 kV (peak) (xii) Primary terminal Material & details - Copper. (xiii) Surface Finish of MS components exposed to atmosphere - Painted, RAL 7032. Conforming to standard : IS:16227-1&2/IEC 61869-1&2. self powered micro processor based solid state relays adjustable type suitable for 1 Amp. complete all in respect as directed. Note:- The Current transformer shall be fitted on existing structure. Necessary modification/repair if any required as per recommendation of OEM is under scope of work and cost thereof is deemed to be included in quoted rates by the contractor. Make:- CG Power, ABB or equivalent.

Material & labour for Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (Preferably in vertical position) earth pit not less than 2.25 metre below normal ground level with top edge of the earth plate not less 1.5 metre (BGL) connected to galvanized iron earth strip 32 x6 mm by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 15 mm bore “Light grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 40 mm bore “light grade” galvanized iron protection pipe for earth strip 32 x6 mm upto 7.5 m length, charcoal, common salt, complete all as shown in Earth Plate No 3 of SSR 2009, Part-I, connected to test point complete, all as specified and testing on completion, complete all as specified and directed.

Supply and fixing of High intensity HIP reflective, outdoor, sign board made from hardened plastic aluminium combined sheet 2mm thick, two sheets placed back to back aluminium prop reveted to stainless steel square pipe 40mm x 40 mm of 16 gauge frame of size 1600 x 900mm with not more than 50 letters (alphabets) Frame shall be supported with 25mm and 50mm round 2.7 mtr long (2 Nos) stainless steel dome place. All stainless steel parts polished on plastic aluminium combined sheet, HIP blue reflective sheet shall be pasted on both side and with white fluorescent computer cut tape minimum 11 Cm height to be pasted on sigh board and border of white HIP sheet shall be pasted and including PCC for foundation, complete all as specified and directed.

Supply and laying and connecting up copper strandard control cable in ducts for 66 KV yard to Panel room, 4 Sqmm 12 Core as per the manufacurer design complete all as specified as directed to comply the site requirements, complete all as specified and directed. Note:- (i) Control cable shall be supported with aluminum spacers and saddles in the ducts.(ii) Termination and ferruling shall be done as per approved wiring scheme.(iii) Identification tages shall be provided in the starting and finishing end of the cable at an interval of 5 meter through out the cable length.(iv) Suitable PVC copper thimbles and lugs are to be provided for marking the connection to the terminals.

All as per tiem No 14 above but of size size 2.5 Sqmm 4 Core, complete all as specified and directed.

Disconnecting/Dismantling old unserviceable power transformer of capacity 5 MVA along with connected items complete from site and deposite to MES store yard including necessery transportation and T&P required at site, complete all as specified and directed.

Supply, laying and testing cable XLPE insulated ,screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty), 11000 volts (E) grade with stranded aluminium conductor of 3 core 300 Sqmm size, complete all as specified and directed. Note:- Excavation & earth work , sand cushioning, cable protection cover, pipe and joint shall be measured and paid separately under respective items of BOQ.

Material & labour for Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminum conductor cable of size 300 sqmm, complete all as specified and directed.

JAZZCON ENGINEERS PVT LTD (BID ID -3309776)

Raman Electric Trading Co (BID ID -3310229)

Sant Construction Co. (BID ID -3310637)

SHREE KARNI LIGHT HOUSE (BID ID -3311285)