ADDN/ ALTN AND SPL REPAIR TO BUILDING NO CT-8, CT-9, CT-11 AND CT-12 AT CHUNGTHANG (PHU GROUND) FOR FD HOSPITAL UNDER GE 867 EWS

Amount

M & L 75 mm thick Cement concrete type C2, 1:3:6 (40mm graded aggregate) as in sub base. Complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, for ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling. Complete all as specified and directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6. Complete all as specified.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work, or concrete work rendering finished even and smooth (without using extra cement), complete all as specified and directed.

Taking down cement plaster on brick or stone masonry surfaces of walls etc including raking out joints, hacking for key, scrubbing down with water etc. Complete all as specified and directed.

M & L rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement mixed with intergral water proofing compound @ 2% by weight of cement (WPC measured and shall be paid separately). Complete all as specified and as directed.

Supply only integral water proofing compound. Complete all as specified and as directed.

M&L for glazed ceramic colouered tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick as in vertical surface such as risers of steps, skirting, dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 10 mm thick rendering in cement mortar (1:4) finished even and rough, complete all as specified and directed.

M&L for light shade virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tiles over and including 15mm thick screed bed or bedding layer in cement mortar (1:6), complete all as specified and directed.

M & L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 15 mm thick screed bed in cement mortar (1:6). Complete all as specified and directed.

S & F GI frame work of size 605 x 605 mm, for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Complete all as specified and directed.

S & F 10mm thick PVC insulation panels with EPS stuck to 1mm printed PVC sheet suitably placed in false ceiling grid made of Aluminium /G.I./M.S as per specification and drawing. Complete all as specified and as directed.

S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. Complete all as specified and as directed.

S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. Complete all as specified and as directed.

M & L for RCC Design mix M-25 (20mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like. Complete all as specified and as directed.

Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces. Complete all as specified and directed.

M & L for RCC Design mix M-25 (20mm graded aggregate) as in Beams, cantilevers bressummers, lintels over 1.5M Span

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. Complete all as specified and directed.

M & L for Mild steel bars 10 mm dia and over, cut to length,bent to shape required,including cranking ,bending spirally for hooping for columns,hooking ends and binding with and and including mild steel wire(annealed) not less than 0.9 mm dia or securing with clips. Complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified and as directed.

M & L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. Complete all as specified and directed.

S & F sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe, waste coupling; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S & F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste pipe and waste coupling; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm. Complete all as specified and directed.

S&F of vitreous china wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, flush pipe of polyethylene of low or high density or PVC. 32 mm dia including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and directed.

S & F bib taps 15mm bore cast copper alloy chromium plated with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed 15mm bore, complete all as specified and directed.

S & F 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed. Complete all as specified and as directed.

S & F Stop cock 15 mm bore cast copper alloy screwed down high pressure fancy type, chromium plated with long shank and cup (concealed type). Complete all as specified and as directed.

S & F PVC connections 15mm size with PTMT nuts of length 600mm. Complete all as specified and directed.

S & F in repairs 25mm dia curtain rod (curtain rails), alumunium alloy, powder coated with and including decorattive knobs etc, complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. Complete all as specified and as directed.

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors. Complete all as specified and as directed.

S & F 20mm outer dia CPVC ball valve. Complete all as specified and directed

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m. Complete all as specifed and directed.

M&L for preparation of new plastered or unplastered surface of wall and applying two coats of distemper oil emulsion (OBD), over a coat of priming coat (alkali resistant priming paint, on plastered surfaces, preparatory to distempering) including 1mm thick wall care putty on wall, complete all as specified and directed.

M & L for three coats of white wash on new plastered surface including prepration of wall surface, complete all as specified and directed

M & L for two coats of cement base paint over a coat of primer with alkali resistant priming paint on newely plastered surfaces of wall including preparatin of walls etc. Complete all as specified and directed.

Material & Labour for preparation of newly plastered surfaces of wall and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. Complete all as specified and as directed.

S & F pressed steel frame of size 125 x 60mm for door with one or more rebates including necessary fixing, lugs, hinges,lock ,strike plate, etc. Complete all as specified and as directed.

S & F 30mm thick flush shutters, solid core construction, with particle board core and one face is covered with decorative face veneer with lipping/frame to match. Complete all as specified directed.

M & L for two coats of synthetic enamel paint over a coat of pink primer on wood based surfaces of any description, over 10 cm in width or girth, not otherwise described including preparation of surfaces. Complete all as specified and as directed.

S & F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified.

S & F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified.

S & F power coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. Complete all as specified and as directed.

S & F power coating (minimum thickness of powder coating 50 micron) aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. Complete all as specified and as directed.

S & F power coating (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. Complete all as specified and as directed.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S & F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.50 sqm in each pane, complete all as specified and directed.

S & F 4 mm thick sheet frosted on one side and glazing with oil putty in square exc 0.50 sqm in each pane, complete all as specified and directed.

S & F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S & F butt hinges, 100 mm size, heavy weight, cold rolled mild steel and fixed. Complete all as specified and directed.

S & F aluminium door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed. Complete all as specified and directed.

S & F 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor. Complete all as specified and as directed.

S&F of 150 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed all as specified and directed.

S & F 150mm long aluminium handle cost type anodised, complete all as specified and directed.

S&F of 250 mm long aluminium alloy, anodised sliding door bolts with haps staple(bolt type), and fixing clips of sheet, cast or extruted sections and fixing bolt and sliding bolts of extruted sections or cast aluminium alloy and fixed, complete all as specified and directed.

S & F 4 levers aluminium mortice lock, vertical type, size 100 mm with keys, complete all as specified and directed.

Providing and fixing steel roller for Aluminium sliding door with necessary screws etc. Complete all as specified and as directed.

Providing and fixing steel roller for aluminium sliding window with necessary screws etc. Complete all as specified and as directed.

Providing and fixing zinc alloyed (white powder coated) touch lock for aluminium sliding window with necessary screws etc. Complete all as specified and as directed.

M & L for 18/19mm thick Prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations fixed with screws to timber frame wor. Complete all as specified and as directed.

M & L for second class hard wood timber scantling in timber framed work and fixed in clean sawn, complete all as specified and directed.

M & L for preparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S & F 40mm (width of flaps when open) continuous (piano) hinges, mild steel, bright finish or electrogalvanised, complete all as specified and directed.

S & F brass drawer handles, projection drop 65mm on screwed plate, complete all as specified and directed.

S & F 75mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws. Complete all as specified and as directed.

S & F 2 lever brass Lock, cupboard, grade I, size 65mm, complete all as specified and directed.

M&L preparing old painted steel and iron surfaces of any description over 10 cm width or girth including CGI sheet in roof etc and applying two coat of synthetic enamel paint over a coat of primer including complete removal of existing treatment, complete al as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS framewelded/ sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement in the frame at site as per specification.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws

S & F Vitrous China wash down water closet pan pedestal pattern white, inclusive of PVC seat cover white recess bottom type mild steel chromium plated or aluminium handing device and fixing 'P' or 'S' trap, connecting to union of flushing cistern and drain pipe complete all as specified and directed.

S & F PVC valve less , syphonic action type flushing cistern 10 ltr capacity low level, whit, with inlet, ball valve float, flush pipe and handle including brackets, low level fluslhing cistern (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, if any

S & F CP towel Rail 20mm dia, D type, 60cm long between flanges etc, complete all as specified.

S & F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement. Complete all as specified and as directed.

S & F Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws with flat recessed type stainless steel. Complete all as specified and directed

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F PVC (SWR) "P" trap 110 mm bore complete all as specified and directed.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S & F 3mm sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane, complete all as specified and directed.

S & F PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joints fixed to walls (ISI marked), complete all as specified and directed.

S & F PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joint laid in trenches or in floor, complete all as specified and directed.

S & F PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joint laid in trenches or in floor, complete all as specified and directed.

S & F PVC ( SWR ) bends 75 mm bore, complete all as specified and directed.

S & F PVC ( SWR ) bends 110 mm bore, complete all as specified and directed.

S & F PVC (SWR) couplers suitable for 75mm bore pipe including jointing with solvent cement, complete all as specified and directed.

S & F PVC (SWR) couplers suitable for 110mm bore pipe including jointing with solvent cement, complete all as specified and directed.

S & F PVC (SWR) reducer 110x75 mm including jointing with solvent cement, complete all as specified and as directed.

S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out. Complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m and making good surface. Complete all as specified and directed.

M & L for PCC 1:3:6 type C-2 (40mm grade aggregate) in foundation of post holes, complete all as specified and directed.

S & F mild steel work in tubular trusses, purlins including special shaped washer etc. compolete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 as in frame work for sun shade, roof, projection etc. Complete all as specified and directed.

S & F for Roof trusses (Framed), trussed , purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections ) including distance pieces cleats etc FE-410W (Gde E-250) quality A, complete all as specified and as directed.

S & F for framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as specified and as directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws. Complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer. Complete all as specified and directed.

M & L preparation of new or previously untreated steel surface any description under 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer. Complete all as specified and directed.

M & L for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

M & L for Pre-cast cement concrete block masonry 1:2:4 Type B1 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:4. Complete all as specified and directed.

M & L for hard core of broken boulder n.exc 63 mm, deposited, spread and levelled in layers n.exe 15 cm thick, watered and rammed to a true surface. Complete all as specified and directed.

M & L for PCC 1:4:8 type D2 (40mm graded aggregate) 100mm thick as in sub base. Complete all as specified and directed.

M & L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand. Complete all as specified and directed.

M & L for coloured & polished Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry as in floors includig 15mm thick screed bed CM(1:6). Complete all as specified and directed.

M & L cement concrete Type B1 1:2:4 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. Complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed

Surface dressing n exc 15 cm deep and getting out in soft/loose soil all as specified and as directed (Including Site Clearance).

Excavating in trenches, n.exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n.exc 1.5 m in depth and getting out in soft/loose soil. Complete all as specified and directed

M & L PCC 1:4:8 type D-2 (Using 40 mm grade aggregate) in foundation, filling and mass concrete. Complete all as specified and directed.

M & L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone agg as in plinth protection/path laid slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges complete all as specified and directed.

M & L for damp proof course 40 mm thick in cement concrete (1:2:4) Type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for RCC Nominal Mix Type B1, 1:2:4 (20 mm graded aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundationand plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Returning filling in , including, spreading, levelling, watering and well ramming in layers not exc 25cm in soft / loose soil, complete all as specified and directed.

Removing excavated material n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point, complete all as specified and directed.

Excavation over area n.exc 1.5m deep & getting out in soft/loose soil. Complete all as specified and directed.

Excavation over area exc 1.5m but n.exc 3.0 m deep & getting out in hard/dense soil. Complete all as specified and directed.

M&L for plain cement concrete bed 1:3:6, type C2 (using 40 mm graded stone aggregate) to drain pipe 100/110 mm bore including packing under and hunching against the sides of pipes after they laid and tested complete all as directed by Engineer-in-Charge.

M & L Plain cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) as in benching of manholes including necessary formwork, weathering, slightly rounded or chamfered angles, finishing of exposed surfaces of concrete to even and smooth without using extra cement complete all as specified and directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4. Complete all as specified and directed.

M & L for brickwork with flyash bricks in one brick thick honey comb walling, built in CM 1:4. Complete all as specified and directed.

M & L for RCC 1:2:4 type B1 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like. Complete all as specified and directed.

M & L for Mild steel TMT bars 6Mmm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. Complete all as specified and directed.

M&L for pre cast cement concre type B1, 1:2:4 (20mm graded stone agg) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM 1:6. Complete all as specified and directed.

M & L for Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells. Complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall with modular back plate and top cover for mounting switches, sockets, fan Regulators, accessories etc as specified and directed for one light point or one fan point controlled by one, one way switch NOTE: 1.Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black). 2. All points shall be earthed up to fixtures i.e holders,tube lights,all lights,ceiling lights,bulkhead lights,bldg security lights etc.

All as per serial item No. 129 here-in-before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per serial item No.129 here-in-before but for one 5 Amp, 5 pin socket outlet point on same board with other switches including earth wire as specified.

All as per serial item No. 129 above but for one 3 pin socket outlet, 5 Amps on independent board but below the switch board of light points in the same vertical plane, with cables, 1.5 sq. mm size

All as per serial item No. 129 here-in-before but on independent board.

All as per serial item No. 129 here-in-before but with 2.5 Sqmm, PVC copper stranded cable FRLS type for phase, neutral and earth for one 15 Amp, 6 pin socket on independent board.

All as per serial item No. 129 above but for one 3 pin socket outlet, 15 Amps on independent board but below the switch board of light points in the same vertical plane/horizontal plane, with cables, 2.5 sq. mm size

S&F modular switch, piano type, 5 Amp, single pole, one way, flush type, white or ivory, ISI marked all as specified and as directed.

S&F modular switch, piano type, 15 Amp, single pole, one way, flush type, white or ivory, ISI marked all as specified and as directed.

S&F modular socket outlet, 3 pin, 5 Amps, flush type, ISI marked all as specified and as directed

S&F modular socket outlet, 6 or 5 pin & 15 Amps, flush type, ISI marked all as specified and as directed

S&F modular bell push, 6 Amp, one module, 230V all as specified and directed.

S&F electric door bell, 230 V, multi music type, ISI marked all as specified and as directed

S&F lamp holder insulated, PVC / polycarbonate /bakelite body complete all as specified and as directed.

S&F in repairs, LED 12W Inverter Bulb, 230 Volts AC supply, all as specified and directed.

S&F ceiling rose surface bakelite 65x50mm three terminal complete all as specified and as directed.

Supply and fixing energy efficient LED tube lights fitting 4", 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make : Havells/Philips/Crompton

SSupply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete including taking down old u/s light fitting complete all as specified and directed. Make : Crompton/ Philips/Havells.

Supply and fixing LED round/square shape 15 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S&F in repairs, 600 mm x 600 mm size, ultra slim, recess mounted LED luminaire of capacity 36 watt, with driver, for soft glare free light, AC 230 volt complete with all acessories and connections, complete all as specified & as directed.

Surface mounted, decorative round plastic bulk head LED luminaire comprising of high brightness LED's, IP54 protection, 10 watt, 6000K complete fitting with LED lamp, driver and all other fixing accessories including electric connection connecting with using flexible copper wire twin core upto ceilling rose/connector including taking down old unserviceable light fitting any type complete all as specified and as directed by Engineer-in- Charge.

S&F in repairs, security light fitting of building with single piece new generation energy savng and environmental friendly, long life, LED 30W, made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including one bracket made of light grade GI Pipe 25 mm dia, 1.5 mtr long, fixed to wall/ pole with two clamps made out of mild steel flat iron 40 mm x 5 mm and connect to nearest electric supply by two core 1.5 sqmm aluminium cable all as specified and as directed.

Supply and fix electric water heater,storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece including anchoring bolts and making connection and testing complete all as specified and directed.

Supply and install hi wall split AC of size 2 TR units indoor/outdoor complete with cordless remote control unit and with in built Heating and Cooling arrangement and Digital Inverter twin rotary of capacity including anchoring bolts and making connection and testing complete all as specified and directed.

Supply installation, commissioning Refrigerator, electric driven (single phase),capacity 500 ltrs , double door, smart inverter compressor of latest model, energy efficient, eco friendly , digital display, toughened glass shelves complete with all accessories all as specified and directed by engineer in charge.

Supply installation, commissioning of Metal Top Deep Freezer double door single phase 240 volt, 50 Hz storage type Deep Freezer 500 ltrs cap of latest model, energy efficient complete with all accessories all as specified and directed.

Supply and fixing Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V to 250 V with output voltage stabilized at 230v with accuracy of +_ 2.5% and of capacity 1.0 KVA suitable for Refregerator / Deep freezer all as specified and directed.

Supply and fixing Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V to 250 V with output voltage stabilized at 230v with accuracy of +_ 2.5% and of capacity 2.0 KVA suitable for AC all as specified and directed.

Supply and fixing Automatic Hand Dryer for bathroom stainless steel , super high speed for fast drying and energy efficient with sensor range 12cm - 15cmhand dry time less than 20 sec with max speed 26000 RPM , of dimension 29.5 X 32.5 X 17.1 cm with gross weight 5.34 Kg complete all as specified and directed. Make/ Model No : Euronics Industries / EH210N or as equivalent Make

Supply and fixing Wall mounting fan AC single phase 230/240 Volt of size 450 mm sweep with louver complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and as directed.

S&F in repairs, single pole & neutral DB, 4 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed.

S&F in repairs, single pole & neutral DBs, 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed.

S&F in repairs, factory made, sheet steel distribution boards, TPN, 4 Way, protection class IP-43 with min 100 Amp rating copper bus bar, provision for FP MCB as incomer and SP MCBs as outgoing complete complete all as specified and as directed .

S&F in repairs, MCB, SPN 40 to 63 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and directed.

Supply and fixing MCB Single pole and neutral upto 32 Amps capacity 10 KA 240 Volts 50 HZ. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp, IP 20 protection, complete all as specified and as directed.

Supply and fix MCB single pole (SP), 10 kA of 6 Amps to 32 Amps capacity 240 Volts. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp, IP 20 protection, complete all as specified and as directed.

S&F in repairs, MCCB four pole 63A, Icu16KA, thermal magnetic, 415v AC complete all as specified and as directed.

S&F in repairs, MCCB four pole 100A, Icu16KA, thermal magnetic, 415v AC complete all as specified and as directed.

S&F single pole and neutral enclosure with a 3 pin plug and socket complete with one single pole MCB 25 Amp 240 Volts(AC & Geyser ) complete all as specifed and directed .

Supply, install, commissioning and testing of commercial Air curtain unit for door opening of size 70" x 90" prevention of dust and conditioned air losses, three phase 440 V, 50 Hz, made out of MS/ CRCA sheet of m i n i m u m thickness 18 gauge finished with two coats of red oxide primer and final coat of s y n t h e t i c enamel paint (oven baked) with MS - CRC 18 gauge s q u a r e p e r f o r a t e d suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1- 1.5 m/sec air velocity at floor level for door opening as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m bellow normal ground level, connected to galvanized earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC 1 : 3 : 6 type C-1 , 50 mm thick pre cast RCC 1 : 2 : 4 type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar ,GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 5 of MES SSR Part-I and as directed.

M & L for sub main wiring with 2 runs of 4 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20 mm dia PVC conduit conforming to IS-9537 / suitable size casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduitcomplete all as specified and as directed.

M & L for sub main wiring with 2 runs of 6 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20 mm dia PVC conduit conforming to IS-9537 / suitable size casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduitcomplete all as specified and as directed. Make of wire :- Havels,Finolex, RPG,Standard,HPL.

M & L for sub main wiring with 2 runs of 10 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20 mm dia PVC conduit conforming to IS-9537 / suitable size casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 10 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduitcomplete all as specified and as directed.

M & L for sub main wiring with 4 runs of 10 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20 mm dia PVC conduit conforming to IS-9537 / suitable size casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 10 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduit complete all as specified and as directed.

Supply and laying in trenches or fixing or passing through pipe, 1100 Volts grade, armoured, heavy duty LT UG cable of size 70 Sqmm, 2 core with XLPE insulated stranded aluminium conductor including cable gland, lugs, testing and commissioning including taking out existing cable alongwith protection covers complete all as specified and as directed.

All as per serial item No 176 but cross sectional area 35 sq mm, 3.5 core.

All as per serial item No 176 but cross sectional area 25 sq mm, 3.5 core.

Supply and lay DWC Cable duct pipe of size 40 mm dia confirming to IS : 16205 part 24 for laying of LT cables etc complete with all accessories all as specified and directed.

Supply and lay DWC Cable duct pipe of size 75 mm dia confirming to IS : 16205 part 24 for laying of LT cables etc complete with all accessories all as specified and directed.

M & L GI tube of 80 mm bore light grade for passing through cables under the floor, along the wall or along the pole of following bore dia and fixed to the poles/walls with suitable size of MS clamps and nut and botls/washers etc including taking down old GI tubing complete all as specified and directed.

M & L GI tube of 40 mm bore light grade for passing through cables under the floor, along the wall or along the pole of following bore dia and fixed to the poles/walls with suitable size of MS clamps and nut and botls/washers etc including taking down old GI tubing complete all as specified and directed.

M&L earthing including dismantling old unserviceable complete with galvanized steel earth plate electrode 600mmX600mmX6.3mm buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and connected to and including using 32 x 6 mm galvanized MS strip wire upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES schedule Part-I, and testing on completion including necessary excavation and earth work in any type of soil, PCC(1:3:6) type C1 chamber, pre-cast RCC slab 50mm thick in cement concrete (1:2:4), type B1, reinforced with welded steel wire fabric or XPM, (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe 40 mm dia, light grade 7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed. Note : (a) Length of earthig connection incl GI strip and protection pipe more than 7.5 Mtr will be measured separately. (b) Contractor should conduct necessary test such as Earth continuity, earth resistance test in presence of JE (E/M)/Engr-incharge.

Supply, install, testing and commissioning factory made and tested (including CPRI type test certified) LT Panel box (Design as approved by GE), outdoor type, floor mounted, compartmantalised and IP-54 suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, all as specified and directed, having bus bar chamber with insulated copper bus bars installed on porcelain insulators. The panel shall be dust and vermin proof, made of 3.15mm CRCA MS sheet and with base frame of 40x40x6mm angle iron 45 cm above ground and 45cm grounted in ground with PCC 1:2:4 Type B1 and coping 30cm above ground level,well Ventilated , powder coated, Front and rear opening type with aprons for cable entry with double door shutter and locking arrangement and including dismantling/ taking down old unserviceable LT feeder piller box with framework 900mm (W) X 1250mm (H) X 500mm (D) all as specified and as directed.

Incoming : (a) MCCB 200 amps, 4 pole, 36 KA, 415 volts grade, with thermal magnetic - 01 No (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 400 Amp, 4 pole, mounted on insulators for incomming supply - 01 Set. (c) digital Volt meter ,415 volts, 50 Hz AC supply -01 set. (d) digital Amp meter ,415 volts, 50 Hz AC supply -01 set. (e) Neon indicating lamps (R, Y & B) -01 Set. (f) Control MCB 1P 6 Amp - 04 No , (g) CT 200/5 - 04 No Outgoing : (a) MCCB 100 amps, 4 pole, 36 KA, 415 volts grade, with thermal magnetic - 02 No (b) MCCB 63 amps, 4 pole, 36 KA, 415 volts grade, with thermal magnetic - 03 No (c) digital Volt meter ,415 volts, 50 Hz AC supply -05 set. (d) digital Amp meter ,415 volts, 50 Hz AC supply -05 set. (e) Neon indicating lamps (R, Y & B) -05 Set.

S&F gun metal, globe or gate valves of 25 mm bore dia., with iron wheel head, screwed both ends for iron pipes and fixed including all as specified and directed.

S&F Rotational moulded polythene water storage tank ( cylindrical vertical with closed tops ) hoisted and fixed in position of 2000Ltrs capacity including tank cover and all necessary connection of tank nipple all as specified and as directed.

S&F of GI tubing of 25 mm dia medium grade ISI Marked laid in trenches/laid under floor on ground including all fittings such as elbow, union, reducer, tees, bends etc and short length, complete all as specified and directed.

S&F PVC float valve, high pressure with polythene float and fly nut complete screwed for PVC pipe and fixed in 25 mm bore pipe complete all as specified and as directed by Engineer-incharge.

M&L for cutting, screwing the same for alterations or additions in position including refixing old steel tubing and connections in new or old position by means of equal 'T' of Reduced 'T' junction of dia upto 50mm complete.

M&L for construction of angle iron stage made out of MS equal angle of suitable size of thick complete including fabricated work all as per directed at site.

Note 1:- (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum / amendments and general condition of contracts before entry / quoting the rates. Note 2:-The contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount.

MS ORIENT ENGINEERING WORKS (BID ID -3505542)