REPAIR/REPLACEMENT TO KITCHEN CABINET, CUPBOARDS, JOINERY WORK FOR CERTAIN MD / OTM ACCN FOR ZONE A UNDER AGE B/R-II AT GE JHANSI

Amount

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

Taking down steel window shutter n.exc 1sqm each and refixing in the same opening after replacement of broken hinges including welding,grinding, etc each complete all as specified and directed

Taking down shutter of any description n exc 1 sqm each complete all as specified and directed

Taking down shutter of any description exc 1 sqm and not exc 2 sqm each complete all as specified and directed

S&F Pressed steel frames (125 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, complete all as specified and directed

S&F for MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc of FE-290 (gde E-165) complete drilled for fixing of steel sheeting or other covering. doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering) and hanging: also fastening and fixing complete all as specified and directed

S&F for mild steel, plain, black sheet 1.00 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with ri-veted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed

M&L for MS work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles confirming to FE 290 Gde E-165 complete all as specified and directed

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in bed blocks etc for embedding hold fasts complete all as specified and directed

S&F of Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood coloured PVC sheet and edges, reinforced with MS square tube, as specified in SSR Part-II 2010 (Section 8, on Page no - 175), complete all as specified as directed

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing complete all as specified as directed.

S&F 35mm thick 2nd class H.W. made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc divided into squars, with plain chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitered beads for securing glass/gauze etc, sizes of members of door shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed

S&F 30mm thick 2nd class H.W. made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc divided into squars, with plain chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitered beads for securing glass/gauze etc, sizes of members of window shutters as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed

M&L for box type steel window with 80x40x1.25 m MS tubular frame with side hung shutters ( double shutter for glass and gauze) without sash bars jointed together with and incl grill using 12 mm square bar @ 10 cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars doweled and welded complete all as specified as directed. Note:- (a) The Glass / gauze shell be measured and paid separately. (b) Side hung Z-Section shutter shall be of size 20mm x 20mm x 25mm and 0.3mm thick.

M&L for box type steel ventilator with 80x40x1.25mm MS tubular frame partly gauged with top hung shutter with and incl grill using 12mm square bars @ 10Cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars dovetailed and welded complete all as specified as directed. Note:- (a) The Glass / gauze shell be measured and paid separately. (b) Top hung Z-Section shutter shall be of size 20mm x 20mm x 25mm and 0.3mm thick.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified as directed.

S&F of 30mm thick flush doors shutter, solid core construction, with partical board core and plywood face panel commercial type on both sides complete all as specified and directed.

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 2mm thick Wooden texture moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

S&F butt hinges, 100mm long, medium weight, cold rolled, mild steel complete all as specified and directed.

S&F butt hinges, 100 mm long, extruded aluminium alloy,with mild steel hinge pin anodised complete all fixed type C-21 specified and directed.

S&F butt hinges, 75 mm long, medium weight, cold rolled, mild steel complete all as specified and directed.

S&F butt hinges, 50 mm long, medium weight, cold rolled, mild steel complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S&F 150mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 125mm extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed.

S&F 100mm long aluminium anodized, barrel tower bolts of extruded section complete all as specified and directed

S&F 150mm long aluminium anodized, barrel tower bolts of extruded section complete all as specified and directed

S&F 300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate fixed to wooden/mild steel chowkhat complete all as specified and directed.

S&F in repair 300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate fixed to wooden/mild steel chowkhat complete all as specified and directed.

Preparing surfaces holding the members in true position and welding in repairs n. exc 2.5 cm in length, thickness of metal to be welded exc 9 mm and nexc 20 mm complete all as specified and directed

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed

Hacking out old broken glass pane of any thickness and size from wooden/metal frame including punching or drilling and glazing pins etc complete all as directed.

S&F 3mm thick sheet glass ordinary quality type & glazing with wooden beads in squares not exc 0.5 Sqm in each pan, complete all as directed.

M&L for preparation of new wooden surface of any description over 10 cm width and girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in same colour grout to match with and including laying of 15 mm thick screed bed or bedding layer in CM 1:6 complete including dismantling of existing floor tiling including cement mortar bedding and removing rubbish off the premises complete all as directed.

M&L for light shade Vitrified ceramic coloured tiles 8 to 10mm thick (Square or rectangular) polished,area of each tile not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in same colour grout to match over and including 15 mm thick screed bed or bedding layer in CM 1:6 including dismantling floor hearth or wall tiling including cement mortar bedding complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in same colour grout to match with and including laying of 15 mm thick screed bed or bedding layer in CM 1:6 complete including dismantling of existing floor tiling including cement mortar bedding and removing rubbish off the premises complete all as directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in vertical surface such as skirting dado and riser to step floor etc set and jointed in neat cement slurry and pointed in same colour grout to match with and including 10 mm thick backing in cement mortar 1:4 finished rough surface to receive tiles including dismantling of existing tiling including cement mortar bedding and removing rubbish off the premises complete all as directed.

M&L for Glazed ceramic coloured tiles of size 350 mm x 250 mm x 7mm / 450x350x7mm thick, as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in same colour grout to match with and including 10 mm thick rendering in cement mortar 1:4 finished rough surface to receive tiles including dismantling of existing wall tiling including cement mortar bedding and removing rubbish off the premises complete all as directed.

M&L for Brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6.00m mean radius built in cement mortar (1:6) including demolition of existing brick work built in cement or cement lime mortar etc complete all as specified and directed.

Taking down cement plaster on brick or stone walling built in CM including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering in two coats 15mm (10mm+5mm) thick plaster on fair faces of brick work or concrete surface in CM 1:4 finished even and smooth (without using extra cement) and mixed with water proofing compound as per manufactures instructions, complete all as specified and directed Note- WPC shall be measured paid as supply only under respective items separetely.

M&L for rendering 10mm thick plaster on other than fair faces of brick work or concrete surface in CM 1:6 finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 5mm thick plaster in CM (1:3) on concrete surface of ceiling finished even & smooth (without using extra cement) complete all as specifiied and directed.

M&L for preparation of new plastered surface of wall and applying two coats of internal acrylic emulsion, over chalk whiting primerand including a layer of 1.5mm thick wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint ,over a coat of alkali resistant primer over outer surface of wall, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

S & F 30mm wide Continuous (piano) hinges, mild steel, bright finish or electro galvanised ficed with screws complete all as specified and directed.

S&F in repair 18 mm thick factory single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) including dismantling boarding, cupborad any description, fixed in any position complete all as specified and as directed.

S&F 140mm Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed with screws complete all as specified and directed.

S&F in repair auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed.

S&F in repair ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs complete all as specified and directed.

S&F in repair stainless steel handles 100 mm size for kitchen cabinet shutters complete all as specified and directed.

S&F in repair chromium plated stainless steel wire basket (storage basket) pull out type for large utensils, size 480 x 500 x 150 mm of Grade 304 with necessary fixing clips etc complete all as specified and directed.

S&F in repair chromium plated stainless steel wire basket (cup and saucer basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc complete all as specified and directed

S&F in repair chromium plated stainless steel wire basket (plate basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc complete all as specified and directed.

S&F in repair chromium plated stainless steel wire basket (cutlery basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc complete all as specified and directed..

S&F in repair chromium plated stainless steel wire basket (Grain Trolley) pull out type, size 480 x 500 x 200 mm Grade 304 with necessary sliding frame structure, fixing clips etc complete all as specified and directed.

S&F in repair chromium plated stainless steel wire basket (Bottle pull out) pull out type two self, size 120 x 500 x 432 mm with necessary sliding frame structure, fixing clips etc complete all as specified and directed.

S&F in repairs drapery rod in any length, high strength stain less steel pipe with corrugated stain less steel extrusion having outer dia 25mm a pair of brackets complete all as specified and directed.

S&F in repairs decorative finals stainless steel in matching colour of rod complete all as directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit including cutting chasing in brick work and half rounding of granite edges in front face of self including 15 mm screed bed in cement motar (1:4) including demolation of stone slabs any thickness complete all as specified and directed.

S&F door seal Rubber strip (door seal) 25mm wide fixed to door complete all as specified and directed.

ANURUDH CONSTRUCTION (BID ID -3325327)

FTH TRADERS (BID ID -3323729)

ADARSH ENTERPRISES (BID ID -3323364)

V S CONSTRUCTION (BID ID -3333698)

AGRASEN ENTERPRISES (BID ID -3324216)

Khushi Muskan Engineer & Developer (BID ID -3321583)

M/s Jagdish Chandra Arora (BID ID -3324256)

M/S PRATEESH SAHARIYA (BID ID -3333704)