Attending Major Fault in 15,20,30,40,62.5 KVA EA Sets at Dharmapuri OA (Sw- Attending faults in EA sets under Harur SDCA)

Replacing/ providing afresh mandatory minimum spares as mentioned below for EA sets upto a capacity of 30 KVA to make it functional in manual mode alone, including dismantling the faulty items, taking to workshop if necessary, fixing after servicing, etc., as required.

Braided Fuel hose1.5 mtr length with 2 Nos end sockets

V Belt

S/R metalic door hinges

S/R acoustic canopy door handles & Lock

Servicing of charging alternator

Servicing of Fuel injection pump and Nozzle

4 way Bakelite 100 amps Connector

LED indication lamp

Stop solenoid

S/F banjo bolts

S/F Electronic hour meter 230V including interconnecting wires

S/F battery lead 35 Sqmm multistrand copper about 1Metre length i/c brass/copper eye bolt for both ends

Coolant for Radiator

Starting Key

LLOP switch

Radiator hose and clip

DG Start /stop push button

10 Sqmm Multi strand copper cable

63 A R W fuse cutout

63A 4Pole isolator

S/L 4x16 sqmm Aluminium armoured UG Cable

S/M End termination with brass compression gland and aluminium lugs and crimping the sockets for 4x16 sqmm Al Armoured UG Cable etc

Diesel fuel Hand primer Pump

4 ST Coil

Fault rectification in control wiring in control panel with 4sqmm multistrand copper cable

Carrying out Oil servicing for the existing 15/20KVA Engines with replacement of Lub oil Filter,Diesel Filter and Lub Oil 15W/40 of reqd qty etc as reqd. (i) Lub oil filter (ii) Diesel filter (iii) Lub oil 15 w / 40 // All the above consists of //

Replacement of the faulty 12 V 10A SMPS Battery charger suitable for operating on 230V 50Hz single phase AC supply in the 15KVA EA set AMF control panel, testing commissioning etc as reqd

Providing & fixing Automatic Voltage Regulator (AVR) in the existing 15 KVA Alternator i/c dismantling the faulty fixing the new one, testing and Commsiioning etc., as reqd.

Cleaning of diesel tank including draining the fuel residuals, decoupling the inlet and outlet valves, washing with cotton waste, drying, reconnecting the inlet and outlet valves, etc. as required.

Servicing of radiator including dismantling the radiator from the existing position, by dismantling the inlet and outlet water pipe line, taking to workshop, brazing the rusted pipes, core cleaning with chemicals, washing, taking to site after servicing, fixing testing, commissioning etc, as required.

Top overhauling of 20 KVA Air cooled EA set of Eicher make by replacement of 3Nos Piston & rings, 3 Nos sleeve cylinder,3 Nos. Connecting Rod assembly,CR end Bearings,3 Nos Valves intake, 3Nos valve exhuast, 3 Nos guide valves and 3 Nos seat valves, Fuel Filter, oil filter, Oil Seal, Lub Oil 10 ltrs, Liner, Set of gaskets,O rings ,CR end bearing , Arresting oil leakages etc., as required

Carrying out Oil servicing for the existing 30 KVA Engine with replacement of Lub oil Filter,Diesel Filter and Lub Oil 15W/40 of reqd qty etc as reqd. (i) Lub oil filter (ii) Diesel filter (iii) Lub oil 15 w / 40 // All the above consists of //

Supplying and replacing radiator set suitable for 30 KVA EA set including dismantling the faulty radiator, fixing the new one, dismantling and fixing the radiaor hoses, testing, commissioning etc., as required.

Supplying and replacing self starting Motor Operating on 12V DC supply suitable for 15/20 KVA EA set including dismantling the faulty motor, fixing the new one, dismantling and fixing the starter wiries, testing, commissioning etc., as required.

Supplying and replacing of radiator water pump assembly suitable for 30KVA EA set including dismantling the faulty pump with inlet and outlet hoses, fixing the new one with inlet and outlet hoses, testing, commissioning etc., as required

Supplying and replacing Air filter i/c dismantling the faulty one, fixing the new one, testing commissioning etc., as required

Air filter Oil Bath

Dry Air Filter

Rewinding of the main rotor of 3 phase alternator of following capacity as per the original design including transportation to workshop and back to site after rewinding, checking the IR values, winding resistances values, after deducting the scrap value of burnt out winding wire, etc as required

DANI ENGINEERS (BID ID -741013)