SPL REPAIR TO BLDG NO T 23 AND T 24 OF 165 MH PROVN OF COVERED VEH PARKING SHED FOR SPL MODIFIED VEHS OF 3 CESR OPEN SHED IN DHOBI GHAT AT 165 MH AND KOTA STONE AT UNIT KOTE BLDG NO P390 OF 4003 FD WKSP AT RMS

Amount

B/R Portion Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling Plain corrugated steel sheeting, any gauge, thickness, including, Nanital or similar pattern roof covering complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets

Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of reed, lathing, single or double, including battens and olaster or chicken wire lathing complate all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specifed and as directed

Taking down chowkats with shutter n.exc 1.5 Sqm each (without taking off shutters from the frame).

Taking down door chowkats with shutter exc 1.5 but not exc 4 sqm each (without taking off shutters from the frame).

Taking down door shutter exc 1 sqmtr but nex 2 sqmtr each and removing to store complete all as specified.

Formwork to chajjas including edges for flat rough finished surfaces.

M&L RCC M-30, 1:1.5:3, type B-1,( Nominal mix) as in chajjas.

M&L for TMT steel bars 10 mm dia and above, as in reinforcement for concrete, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm.

All as per item No 16 above but above 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

M&L for Cement concrete type B-1 1:2:4, as in levelling course (using 20 mm graded aggregate), 40 mm thick complete all as specified.

M & L for PCC 1:2:4 type B0 (using 12.50mm graded stone aggregate) 25 mm thick as in sub base to receive tiles.

M&L 100mm thick Cement concrete 1:2:4 type B- 2, (40mm graded aggregate) as in floor finished even and smooth complete all as specified

M&L for Coloured /light shade vitrified ceramic tiles 10mm thick (square/regtangular) polished , area of each tiles not exc 0.36 sqm in floors etc and joineted neat in cement slurry and pointed in white or colour cement to match.

M&L for Coloured /light shade vitrified ceramic tiles 10mm thick (square/regtangular) polished ,area of each tiles not exc 0.36 sqm matching with floor as in skirting etc and joineted neat in cement slurry and pointed in white or colour cement to match.

M&L for Rendering 10mm thick in CM 1:4 as in backing coat of as in skirting and glazed tiles in walls

M&L for Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes with CM 1:6.

S&F Plain, solid straight chowkat and frames, wrought, frmed rebated on the solid, rounded or chamfred put together with glue pinned at joints , supplied and fixed in 2nd class hard wood.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-Charge.

M&L for 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions

S&F for providing sliding type (3 Track +3 shutter) aluminium windows, section profiles of aluminium as per sketch No SK/2019/01 dated 21/01/19, aluminium alloy extruded sections conforming to HE 9-WP of BIS 733 and HP 9 -WP of BIS 1285 as amended, with minimum thickness of frames (outer bottom, Top & side ) 1.5mm and sliding sash (stiles & rails) of minimum thickness 1.2 mm. The windows shall be procured from a BIS license factory manufactoring windows to BIS-1948, The EPDM gaskets, rollers, recessed handles cum locks aluminium snap beading for receving glass/wiremesh with stainlss steel screws shall b provided with windows. The aluminium extruded section shall be of make Jindal/Hindalco/Alom extrusions etc all as listed. Note:- Glazing and Stainless steel wire mesh will be paid seperately.

S&F Aluminium deco grills made out of fixed indepently on outsode of sliding window system in Aluminium C channel on top & Bottom, wt of aluminium alloy grill not less than 1.5 Kg/m2

All as per item No 28 here-in-before but in ventilators, with sliding type lovers and provision for fixing exhaust fan/fixed type Glazing all as shown on drg (Area of ventilator not exceeding 0.50 Sqm)

M&L for Preparing new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

all as per Item No 31 here-in-before but on old wooden surfaces

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 100 mm thick Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F Aluminium bow handles, cast type, anodised 150 mm long

S&F Aluminium bow handles, cast type, anodised 125 mm long

S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed

M&L for Second class clean sawn hardwood in scantling fixed in timber framed work complete all as specified

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6

All as per Item No- 39 here-in-before but half brick walls built in CM 1:6, complete all as specified

All as per item 39 here-in-before but using old bricks retrieved from demolition under item 05 above including cleaning and removal of mortar from old bricks.

Supply and fixing 0.71 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc in walls, ceilings, stanchions, beams etc, including all laps cutting and waste complete all as specified and as directed.

Material and labour for rendering 15 mm thick plaster in cm (1:4) with using water proofing compund on one side of lathing finished even and smooth with out using extra cement cpmlete all as specified and as directed.

Material and labour for rendering 15 mm thick plaster in cm (1:6) other than fair face side one side of lathing finished even and smooth with out using extra cement cpmlete all as specified and as directed.

M&L for Rendering 15mm thick cement plaster in CM 1:6 on brick work/concrete surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in CM 1:4 on brick work/concrete surfaces finished even and fair with WPC @ 2% by weight of cement content and without using extra cement complete all as specified and directed.

Complete removal of existing treatment and applying two coat of oil bound distemper white or tinted on walls over a coat of alkali resistant primer over 1.5mm thick wall care putty etc all as specificed and directed.

M&L for preparation of new plastered surfaces of wall applying two coat OBD white or tinted on walls over a coat of alkali resistant primer over 1.5mm thick wall care putty of approved shade all as specified and as directed.

M&L for preparation of old painted surfaces by removing the existing treatment completely and applying two coats on external wall of Antifungal exterior emulsion paint over a coat of primer and 1.5coats of wall care putty complete all as specified and directed by E-in-charge.

All as per Item No 49 here-in-before but on newly plastered surfaces on external wall complete

S&F for Joist,channel ,angle,or tee sections,fixed independently, without connecting plates ,etc (cut to ordinary length ie within 20mm of the length indicated Fe -410-W(Gde-E-250 qaulity-B) all as specifed and directed by Engr-in -Charge.

S&F Plates (plain or chequered) channels,square cut or notched (ordinary and counter shunk forming holes,without any attachement. All as specified and directed by Engr-in-Charge

S&F Wind ties for roof including securing bolts ,posts and struts including all necessary drilling bolt or riveting etc. and similar work confirming to FE-290 Gde-165

S&F Pre-painted galvalume aluminium zinc coating GI based trapezoidal profile steel sheet 0.50mm (TCT) an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified. Profile sheets complete all as specifed in particular specification.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick on ridge an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

Preparation of two coat of synthetic enamel paint over one coat of red oxide,zinc chrome primer on newly prepared steel surface of any description,over 10cm width or girth,not other wise described all as specified and directed by Engr-in-Charge.

Preparation of two coats of synthetic enamel paints surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint, over a coat of red oxide, zink crome primer complete

S&F 16 to 20mm dia Mild steel screws bolts(Machine made)with hexagonal or square heads at one end and screwed both ends ,each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10cm and n.exc 15cm long. with washers.

M&L for Preparation of old painted surfaces of steel & Iron of any description over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) all as specified and directed by Engr-in-Charge.

M&L for 100mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L 80mm thick Coloured (Yellow & red) interlocking (M-35) cement concrete tiles of approved design & pattern with grey cement and pigment laid over and including 25 mm thick layer of sand cushioning, Complete all as speciifed and directed.

Sand filling under floors or in foundations including watering and consolidation

M & L for 75 mm thick PCC 1:3:6 type C2 , using 40 mm graded agg in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified. (NOTE:-. GI frame work shall be measured & Paid seperately)

S&F size of grid 605 x 605 mm GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre

Material and labour for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in surface channel and like etc complete all as specified and as directed.

S&F Sheet glass ordinary quality 4.00 mm thick and glazing in aluminum window in squares n exc 0.5 sqm each

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm.

Excavating in post holes (or similar holes) each n exc 0.5 cu. M, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in soft/ loose soil.

M&L for Plain Cement concrete type B-2, 1:2:4 (using 40mm graded aggregate) as in foundation filling and mass concrete all as specified.

S&F steel work in tubular trusses, purlins, pillar etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240

S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other end to be fitted with washer and one hexagonal or squre nut n exc 15cm long 12mm dia

Fixing only in same opening flush shutter 35mm thick 08022Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engineer-in-Charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and mirror polishing including 15mm screed bed or bedding layer in 1:4 CM complete all as specified as directed

All as per Item No 74 here-in-before but on vertical surfaces over 15mm screed bed or bedding layer in 1:3 CM complete all as specified and as directed by Engineer-in-Charge.

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc.

All as per item No 76 here-in-before but exceeding 30 cm inner girth upto and including 25 mm girth or part thereof

M&L for PCC 1:4:8 type D-2 (using 40mm graded agg) as in foundation, filling and mass concrete.

M & L rendering 15mm thick in cement mortar 1:6 on fair faces of brick or concrete work even and smooth without using extra cement.

M & L rendering 15 mm thick in cement mortar 1:4 on fair faces of brick or concrete work even and smooth without using extra cement.

M&L hard core of broken stone and boulders of gauze not exc 63mm deposited, spread and leveled in layers not exc 15cm thick watered and rammed to a true surface.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash all as specified & directed by Engineer-in-Charge

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil

E/M Portion Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.

M&L for point wiring complete with two runs of 1.5 Sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked casing & caping including provision of 1.5 Sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches/ sockets/ regulators etc. with 3mm thick plastic laminated sheet cover of suitable size as required at site complete all as specified and as directed.

One light/ Fan point controlled by one way swithc

One 3 pin socket outlet 5 Amps on the same board with other swithces

One 3 pin socket outlet 5 Amps on the Independent board

All as per item No 86 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

M&L for Switch piano flush type single pole, one way 5A Make:- Havells/Legrand/Anchor

M&L for Socket outlet, 2 in 1, 3 pin 5A flush type Make:- Havells/Legrand/Anchor

M&L for Switch Socket combination, 2 in 1, 5 pin 5A flush type Make:- Havells/Legrand/Anchor

M&L Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type Make:- Havells/Legrand/Anchor

M&L for stepped type electronic fan regulator 100/120 Watt socket size flush type on the existing phenolic laminated sheet etc. Make:- Havells/Legrand/Achor

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. Make:- Havells/Legrand/Achor

S&F for , IP>= 20, Class-I, LED Light fitting 1 x 20 watt (4 Ft), 240 V, PF-0.9, CRI >= 80, CT>= 6500 K, Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with and incl twin/ three core twisted flexible copper conductor cable of suitable size in and incl flexible hose from ceiling rose to fitting complete all as specified and as directed. Make : Crompton Geaves Cat No -CCS-102-20-65-SL-DP-NWH/ Bajaj/ Philips.

Supply and fixing LED luminaire 600 mm x 600 mm, 40/42 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as speicfied and as directed.ake Havells C

Supply , fixing and testing in replacement of LED Bldg Security light fitting of capacity 20 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting and all as specified and directed by Engr-in-Charge.

Taking down Exh/Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.

M&L for rubber bush with clamping set, comprising GI bolt, nut and split pin complete all as specified and as directed.

M&L for replacement of capacitor 2.5 Mfd incl making electrical connection complete all as specified and as directed.

M&L for replacement of steel ball bearing/bush of suitable size compatible to the existing ceiling fan/Exhaust Fan complete all as specified and as directed.

M&L for copper rewinding for suitable size complete to the existing ceiling /Exhaust fan complete all as specifed and as directed.

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. Make:- Legrand Cat No 607711 or equivalent in ABB/Siemens

M&L for MCB SPN 32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand Cat No 408636 or equivalent in ABB/Siemens

M&L for MCB SP 6-32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand Cat No 408587-95 or equivalent in ABB/Siemens

Taking down burnt unsv LT UG cable of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16 sq mm, 2 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.

All as per item No 105 here-in-before but 6 Sqmm 2 core complete all as specified and as directed

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified and as directed.

Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified and as directed.

M&L for spread fine river sand in trenches complete all as specified and as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed

Supply & laying tubes ' light grade' galvanised, with clamps suitable fixed complete to walls, poles, ceilings for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. Make:- Jindal/TATA/Prakash surya

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed.

SHRI HRIDAY NARAIN GIRI

M/S Lucky Builders

SHRI MADAN SINGH

MS SADHNA RAHUL

SHRI RAJNATH SINGH

PERFECT BUILDERS AND SUPPLIERS

SK SINGH