PROVN OF (QTY-01) 125 KVA GEN SET (SILENT TYPE) FOR BLDG NO 189 AND 191 AT 506 ABW AND PROVN OF PIPE LINE FROM BOREWELL NO 15 TO OH TANK AT RESTRICITED AREA OF 506 ABW AND OTHER SANCTIONED WORKS UNDER AGE E/M OF GE(EAST) JABALPUR

Amount

Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr deep for laying pipes etc n.exc 10Sqm on plan and getting out in soft/loose soil complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exce 25 cm thick complete all as specified and directed

Removing excavated soil to a distance not exce 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point all as specified and directed.

M&L for Plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation of poles, filling of road cutting etc complete all as specified.

S&F the followiing Gun metal Globe or Gate valve with iron wheel head, screwed both ends for iron pipe and fixed with required necessary GI fittings complete :- Make : Kartar/Zolto/ Sant/ Leader

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

S&F the followiing GI tubing medium grade with all fittings and fixed complete laid in trenches of size :-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

S & F of Ductile Iron pipe 150mm bore with spigot and socket ends Class 'K'-9 with all fittings, laid in trenches complete all as specified and directed.

-Ditto- All as per item No 07 above but size 100mm bore.

M&L for run lead joints for the following size of pipes complete for water mains with spigot & socket pipes and fittings complete all as specified and directed:-

150 mm bore

100 mm bore

80 mm bore

S&F rubber tyton joint of following size :

150 mm bore

100 mm bore

80 mm bore

S&F rubber gasket joint for flanged end pipe & fittings of following size :

150 mm bore

100 mm bore

80 mm bore

Material and labour for ISI marked DI pipe fittings up to size 80 to 200 mm dia such as bends, Tapers tale pieces, Tee pieces (single branch) Y juction double branch, cross collars, caps and plug set including rubber ring push on joints complete as specified and directed

Supply and fix CI sluice valve with forged brass stem class PN- 1.6 ISI marked with stainless steel spindal and flanged both ends of size 80 mm dia bore with hand wheel.al as directed Make Kirlosker/ Upadhyay/L&T.

-Ditto- all as per item No 13 Above but size 100mm bore.

-Ditto- all as per item No 13 Above but size 150mm bore.

Supply and fix Non Return Sluice Valve, class PN- 1.6 ISI marked with flanged both ends of size 100 mm dia bore with hand wheel.al as directed .Make Kirlosker/ Upadhyay/L&T.

-Ditto- all as per item No 16 Above but size 150mm bore.

Supply and fix Air release Valve, class PN- 1.6 ISI marked with flanged both ends of size 100 mm dia bore with hand wheel.al as directed .Make Kirlosker/ Upadhyay/L&T.

Cutting of road /hard standing for laying /dismentling of pipe line and making good surfaces matching with the existing surface after laying of pipe line.up to 30 cm

M&L for construction of masonry valve pit (as per drawing No CEJZ/TD/819/91 dated 16/04/91) with the following specification:- Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 1200 x 1200x1200 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mmx40mmx5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and three coats of white wash and preparation of surfaces complete all as specified and shown on drawing

Supply, install commissioinng and testing compelete static diesel Engine driven generating set (Silent) capable of delivering 125 KVA or of next higher capacity as available/manufacturered 415 Volts (AC 3 phase 4 wire system of supply) 50 Hz at power factor 0.8 minimum. The DG set shall consist of a diesel engine coupled directly to alternator a maching parts or as recommeded/provide by the manufacturer on a common base frame and thereafter installed in the CPCB approved acoustic enclosure (The complete set conforming to and test certificates as per CPCB norms and as specified) all as specified complete with control panel standardized by manufacturer, fuel tank with mounting arrangement and inlet, outlet return oil arrangement flexible exhaust pipe complete and shall comprise the following :-

(a) Engine (Prime Mover) : Diesel engine 1500 RPM of suitable capacity as recommended bymanufacturer but not less than 156 BHP turbo charged water cooled otherwise as applicable to the model mentioned) 12 volts electric battery 180 start complete with fly wheel and all standared fittings/fixtures per manufacturing practice including suitable engine control panel / Dash board with electronic tachnometer. Lub oil temperature & pressure gauges water temp gauge and frequency meter (digital type) including safley automatic shut down in case of fault detection such as high water temperature low lubrication on pressure over speed and also including self starter alternator cogged V belt fuel tank (minimum 12hrs capacity of consumption) with first fill of lub oil and coolant (as applicable) etc

(b) Alternator AC alternator, 3 phase, 415 volts, 4 wire rated line current 154 Amps (Min) for output 125 KVA (100 KW) PP 0.8 1500 RPM insulation class enclosure/SPDP self excited, self regulated brushes, complete with AVR with + 1% voltage regulation directly coupled to and match the above engine.

(c) Anti vibration pads for mounting engine alternator assembly on the base frame/plate or as recommenced/provided by the manufacturer (d) Base Plate : Made out of structural steel as per maunfacturer's recommended design/specifications

(e) Acoustic Enclosure : Provisions of an integral type approved/certified acoustic enclosure (make of enclosure shall be sudhir/jackson as per CPCB for the DG sets to restrict the noise level to 75 dba at one meter along and temp raise within canopy shall not exceed 5 degree C to 0 it shall be made of 16 SWG of manufacturer's standard norms CRC MS sheet with powder coated finish on outside and provided with non inginting the regardant foam fire resistance/retardant as acoustic material and provided penable and lockable doors with air tight gasket interior light arrangement 02 Nos 20 Watt CFL with ON/OFF switch to meet latest emission norm. The base frame shall be of ISMC. it shall also include the following:- (i) Silencer : Absorption type non resistance, resisdential and exhaust pipe covered with asbestos rope lagging extending to about 2 meters outside the DG set room. (ii) Internal wiring with PVC copper conductor cable IS 694 marked FRLS in conduit and fluorescent lamp fittings (iii) Fuel tank of 16 hours capacity but not less than made of 14 SWG CRCA MS sheet duly powder coated and provided with float, guage and fuel float switch

(f) One No 12V x 180 AH 25 plates maintenance free batteries complete with batteries lead provided one side copper thimble and other side heavy duty brass terminal (As recommended by manufacturer) Note : (i) Catalogues : Operation and maintenance manual, spare parts list overhauling manual 03 sets (ii) Maint chart and manufacturer instruction shall be display on wooden board including catalogue board

Earthing complete with galvanized steel earth plate electrode 600mm x600 mm x 6mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to galvanized earth wire 4.00mmdia by means of bolts ,nuts ,check nuts and washers complete up to and including test point made out of 40 x 6mm alum flat including earthing pit , charcoal common salt ,Earthing lead 4.00mm dia up to 7.5m, 20mm dia medium grade GI watering pipe ,G.I. protection pipe 15 mm dia up to 7.5m long, PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including earth work complete all as shown in electrical plate No-3 of SSR-2009 (part-I)

Supply, Installation, testing and commissioning of indoor type panel with angle iron pedastal frame & including steel structure required for installation on cable trench, housing cubicale type, free standing, main LT panel working on 415 V, 3 phase, 50 Hz, AC supply. It shall be extendible at both ends, with copper bus bars, fully compartmentalised, dust-proof and vermin proof, 3.15mm thick CRCA sheet enclosure, painted as per the 7-tank process & suitable for IP-65 proection as per specification and having the following :-

(a) MCCB 4 Pole, 200 AMP, 36 KA with adjustable thermal & Adjustable magnetic release -01 Nos

(b) On Load Change Over Switch415 Volt ,4 Pole,200 Amp complete with Copper Bus bars : Size 40x8mm , 400A, 4 pole - 1 Set.

(c) 100 Amp 4 pole 25 KA MCCB with adjustable thermal & Adjustable magnetic release -02 Nos.

(d) 63 Amp 4 pole 16 KA MCCB with adjustable thermal & Adjustable magnetic release -02 Nos

(f) Ampere meter 0-200 Amps digital type of size 96 sqmm duly prewired FR PVC copper wire of size 1.5 sqmm =01Nos

(g) LED type phase indicator lamp=set of three

(h) All connections from Change Over Switch to busbar & busbar to MCCB shall be made with suitable size of copper strip thimble lugs cost of which included in the quoted rate of items.

(j) All accessories prewired with copper conductor cable multistranded pvc insulated with aluminium thimble lugs etc

(k) Above all complete in all respect including installation of panel including supply and installtion of frame pedestal 600mm and 450mm high above ground level

Supply and fix Heat Pillar, Quartz tube heating elements ,child proof sefety grill stainless steel reflecto 230/240 Volt, electric driven (single phase), having nominal air flow complete all as specified. Make : Havells/Crompton/ Bajaj

Supply & Fixing, connecting & testing of Automatic Electromechanical street light timer switch using infrared sensor based nature switch for automatic switching of street lights ,nature switch operation should be based on nature light lux lavel required illumination level for switching on is < 30 lux and for switching off>10 lux. the sensor should also have part night operation facility for 4-12 hours the sensor alongwith suitable power contractor, incoming-outgoing MCBs should be enclosed in a pole/wall mounted inclosure made out of Rust proof electric shock proof termite proof and FR grade SMC Junction box conforming to IP -54 the circuit should be suitable enough to take 8KW single phase load with contactor 40 Amp conforming to IEC : 60947-4-1 & IS : 13947-4-1 & incoming and outgoing MCBs of rating 40 Amps conforming to IEC 60898/IS 8828 and circuit wiring of minimum 10 sqmm copper conductor wire in and including providing of 50x6mm flat iron clamp including necessry nuts,bolt & washers complete including taking down of existing arrengement complete all as directed by EIC Make of Nature switch Model No Swadeep-02EC8KW3P of Kakatiya Energy system or equivalent in Bajaj/Havells/L&T/C&S as approved By GE.

Supply & Fix 25 Litre storage water Geyser working with 8 bar pressure vertically mounted with 5 years warrenty of tank and 2 year warrenty of heating element of make Crompton/Bajaj/ Jaquar/RACOLD

M&L for Point wiring PVC insulated and PVC sheathed multistranded copper conductor FRLS cable of size 2.5 Sqmm including in concealed PVC conduit fittings and making good to the disturbed surfaces with continuous earth wire of copper 2.5 Sqmm dia to common earth incl. Provn of 3mm thick plastic laminated sheet of appropriate size and fixing to existing CI/MS boxes for mounting of accessories like surfaces sockets and regulators complete all as specified :-

One light/fan/bell point controlled by one way switch complete all as specified

S&F earth enclosure with 2 pin earth plug socket complete with MCB SP 16/20 amp flush type single pole one way .

S&F 15 mm bore GI tubing medium grade with all fittings to walls and ceilings or laid in floors complete all as specified.

S&F 15mm bore, stop cock, cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S&F 15mm bore bib tap cast copper alloywith crutch/buterfly handle screwed for iron pipe complete all as specified. Make - Prayag/Polytuff.

S&F 15mm size PVC connection with PTMT nuts of length 600 mm. Make : Prayag/Pearl/ Parryware

S&F 15 mm bore Gun metal non return valve, screwed both ends for iron pipe complete all as specified

Supply and fix water cooler electric driven (single phase), having approx storage capacity of 80 litre and nominal cooling capacity of 40 Litres per hour complete all as specified. Make : Usha/ Voltas/Bluestar

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 1.0 KVA complete all as specified. Make : V-Guard/ Microtek/ Monitor

Supply & Fix desert air cooler of 75 ltr fibre body white with all accessories of all as directed by Engr-in-Charge. Make Symphony/Bajaj/Videocon/crompton

Sachdeva Enterprises