Repairs to hardstanding, interlocking tiles, chequered tiles and fencing in zone I to VI at CME

Amount

Dismantling of wrought iron or mild steel work as in post etc of any description not otherwise provided for.

Dismantling of old damaged chain link fencing wiremesh any type and size

S&F MS framed work such as grills, gratings, manholes covers flat iron as in chain link fencing etc with ends of bars shouldered or reverted, frame work of water tanks and similar work conf to fe 290.Gde E 165.

Dismantling posts or struts (RCC fencing post) any section, including taking out embedded portion and making good disturbed ground all as specified and directed.

S&F MS angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, bolting etc and similar works confirming to Fe-290 Gde E-165 all as specified and directed.

M&L PCC 1:3:6 type C2 using 40mm graded stone aggregate as in foundation/fencing post fixing all as specified and directed

Supply only chain link MS galvanised fencing, any size or type all as directed by Engr-in-Charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire all as specified and directed. (Note : Line wire shall be measured and paid seperately as supply only)

S&F MS screw bolts (machine made) with hexagonal or square heads at one ends and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut n.exc. 5cm long and dia of shank 8 to 10 mm etc. all as specified and directed

S&F 10mm dia MS round bars conforming to Fe-410-W (gde E-250) quality A or Fe-290 (Gde E-165) as in straining bars in fencing all as specified and directed.

S&Fin repairs galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provn of galvanised mild steel wire staples or steel pins all as directed. (Each line wire to be measured)

M&L for preparation of new steel surfaces of any description exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

Dismantling structural steel work including doors, gate but excluding framed truss etc complete all as specified and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and directed.

M&L PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in wall, for embedding angle iron post including necessary form work etc. complete all as specified and directed..

Demolition of brickwork or stone/boulder masonry/ PCC block masonry, built in cement mortar including all quoins, arches; pillars etc. complete all as directed.

M&L precast solid block masonry of block in PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

All as per item No.17 here-in-before, but except PCC block complete all as specified and directed. Note: Old serviceable PCC block retrieved from item No.16 above shall be reused.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar 1:4 complete all as specified and directed.

All as per item No.19 here-in-before, but except stone. Note : Old serviceable stone retreived from item No.16 above shall be reused

Taking down cement or cement lime plaster on brick or stone walls etc incl raking out joints, hacking for key, scrubing down with water etc. complete all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finishing the surface even and smooth without using extra cement complete all as specified and directed..

M&L for preparing surface of plastered or unplastered of wall and applying two coats of cement base paint complete all as specified and directed

Demolition of cement concrete in ground floors and paving not exc 15cm thick (below or above ground level) un-reinforced complete all as specified and directed.

Demolition of cement concrete reinforced of any description (reinforcement cut as required to facilitate demolition) and in any position not otherwise specifically provided for complete all as specified and directed

M&L 100mm thick PCC 1:2:4, type B-2 using 40mm graded stone aggregate as in subbase complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed

M&L RCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in foundation, including rafts, footings, foundation, beams, plinth beams, base for columns etc basement slab under reamed piles and mass concrete complete all as specified and directed.

All as per itrem No.28 above, but beams such as cantilever, bressummers, lintels over 1.50m span (lintel beams) etc complete all as specified and directed.

M & L for use and waste of formwork to side, of concrete foundation, footings, bases of columns, rafts beams, sides and soffits (if any) of foundation and similar work fair finished concrete surface complete all as specified and directed.

M & L for use and waste of formwork to sides of soffits of floors or roof beam, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc finished fair surface complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions etc finished fair surface complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No.33 above, but 5mm dia and over upto and including 10mm dia in strriups and binders complete all as specified and directed.

M & L for forming contraction (Dummy) joints 65mm deepx10mm wide filled with sealing compound of Grade 'B' complete all as specified and directed.

M&L Hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

Supply only Fine aggregate (sand) for sand cushioning 50mm thick below interlocking paver block all as specified and directed.

M & L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with glossy finish colour shade complete all as specified and directed.

...Ditto... all as above, but except interlocking tiles Note : All serviceable paver block retrieved from sl item No. 43 shall be reused in this item.

Note for sl item No. 38 & 39 :- Rate quoted shall also include for spreading and levelling of sand for cushioning.

M & L for forming 12mm thick expansion joint filled with pre formed bitumen filler and top 30mm primed and sealed with sealing compound grade A, thickness of concrete slab 100mm complete all as specified and directed.

Finishing the surface of concrete pavements by brooming complete all as specified and directed.

M&L for chequered cement concrete tiles 20cmx20cmx25mm thick, set, jointed and pointed in neat cement slurry in floors mixed with grey cement and pigment all as specified and directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M & L 25mm thick rough dressed, lime stone slab flooring, laid dry, jointed and pointed in cement mortar 1:3 complete all as specified and directed.

(Applicable for above all items)

Contrator has to employ skilled/unskilled tradesman with adequate experience & required documents to be submitted to office.

Labour should wear contractors uniform with firm logo, failing which recovery should be made.

Minimum of 02 x teams of each trades shall be available for maint of urgent nature whenever called upon of any trade, failing which recovery will be initiated for not employing adequate labour at site.

Site clearance shall be done by contractor after finishing work and obtain the signature of occupant as the site clearance has done. The same shall be verified and put up before issue of completion certificate

All Scarps will be done with mechanical scaper

Mechanical scaper should be deposited in our store at the time of sample approval

Mukund Engineers and Contractors

M/s ESS KAY Construction

Aakar Construction

vishalconstruction

L.K.R.TIWARI CONSTRUCTION

M/S Sharvi Construction