Construction of Quarters for Assistant Commissioner of Arulmigu Thirucourtallanathaswamy Thirukovil at Courtallam in Tenkasi District

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five M sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

Column Footing, Pedastal and Grade Beam

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as Column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

a. For plane surfaces such as Rectangular or square RCC columns

b. For plane surfaces such as Rectangular or square RCC columns, Landing Slab, Waist Slab, Lintels, sunshades, top and bottom, Bed Blocks, RCC floor Slab, RCC Floor Beams, RCC Roof Slab, RCC Roof Beams, Portico Slabs, RCC boxing, etc.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed. 50mm thick

Providing and laying in position, Standarised Concrete Mix M20 Grade in accordance with IS : 456-2000, using 20 mm and down graded hard brocken granite stone jelly for all RCC items of works with minimum cement content of 325 kg /m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommanded proportions as per IS : 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about ( 5 cum )7730 kg of 20 mm machine crushed stone jelly and with about ( 3.30 cum )5156 kg of 10 - 12 mm machine crushed stone jelly and with about ( 4.79 cum )7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc. and providing fixtures like fan clamps in RCC floor / roof slabs where ever necessary without claiming extra etc, complete complying with stsndard specification and as directed by Departmental officers. The course and fine aggrigates to be used should comply with the requirements of IS Standards. ( No separate payment will be made by the Department for the excess usage of materials.)

Foundation and basement

Ground floor

First floor

Cement Concrete 1:3:6 (One Cement, Three crushed stone sand and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three crushed stone sandand Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Damp proof course with Cement Mortar 1:4 (One Cement and Four M sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used, finishing and curing etc. complete complying with standard specification.

Brick work using using Country Bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:6 (One cement and six M sand) including curing neat finishing, etc., complete complying with standard specifiction.

a. Foundation and Basement in cm 1:5

b. Ground floor in cm 1:6

c.First Floor in cm 1:6

Brick partition walls using best quality using Country Bricks of size 8-3/4" x 4-1/4"x 2-3/4" in Cement Mortar 1:3 (One Cement and Three M Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

a. Ground Floor

Plastering with Cement Mortar 1:5 (One cement and Five M sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three M Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Paving the floor with best quality Vetrified tiles (Morbonite Tiles ) of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three CS sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Departmental officersbefore use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two M sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.First Floor

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed Interior plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and fixing T.W Frames for Doors,Supplying and fixing T.W Frames for Doors,Windows, Ventilators and other similar joinery works with the following sizesand sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors.

Supplying and fixing solid core particle board flush shutter of nominal thick of 35 mm with necessary T.W. internal lipping conforming to IS 2302 with both sides alround commercial ply 35mm thick including supplying and fixing cost of wind appliances and furniture fittings such as 1no .200x12mm aluminium tower bolt 2nos. 150x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the Departmental officers.

Supplying and fixing Solid PVC Door Shutters using 19 Gauge 19 mm MS square tubes for styles and outer frames , 15 mm MS square tubes for top, lock and bottom rails. The Steel Tubes shall be covered with 5 mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The overall size of top rail, lock rail and bottom rail shall be 75 mm x 30 mm. The overall size of Frames shall be 50 mm x 45 mm with suitable rebate for housing the shutter

Supply and fixing of UPVC windows of casement type of the following sizes of approved standard quality 1.50x1.75m,1.20x 1.75m, 1.20x1.30m, 0.90x1.30m.The window should be of multi chambered sections with wall thickness of 2.20mm reinforced with hot dip galvanized to 125GSM and 100% corrosion free. The corners and joints should be screwed and pasted. The window should with stand weather and resist UV radiation. Pin headed glass of 4mm thick should not allow leakage of water even in most ranging storms and should have multi chamber profile with double seal that ensures in herent insulation against sound infiltration. The window shutter should have key lockable action security protective hinges, strong double and triple glazing options are to be provided as per the size for arresting noise and every loss. The connecting mechanism between sash & outer frame that enables opening of the window to the desired size and non corrosive SS304 grade should be used for friction stay. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The cost inclusive of supply conveying and fixing in position by sealing the gap between the windows and the with silicon etc.,

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying & fixing of Grill with iron Angles frame of size 40mm x 40mm x 6mm and inner side 12mm Square rods and necessary painting with one coat of Red Oxide primer including cost and conveyance of all materials and all alabour charges etc complete as directed by Departmental officers.

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing of Cudppah Slab of 50 mm thick for the Cup Boards including labour charges for fixing Cudappah Slab to the Cub Boards as directed by the Departmental Staff.

Supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the Departmental officers.

Supplying, laying and jointing uPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety below Ground Level conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using uPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, uPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The uPVC pipes shall be got approved by Executive Engineer before use on works.

15 mm dia uPVC Pipe

Supplying, laying and jointing uPVC Pipes of the following dia of approved quality and best variety above ground level including fixing of PVC Specials but excluding cost of such specials and cutting and threading of pipes but including fixing to the wall with necessary clamps and screws, Teak wood plugs making holes in the wall (or) drilling holes in the roof and making good of the disturbed portion to the original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges. etc., complete complying with standard specification.

25mm dia uPVC Pipe

20mm dia uPVC Pipe

Supplying and fixing in position the following uPVC Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of GI pipes, jointing the GI specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification. (The GI specials should be got approved by the Depatmental Officrs concerned before use on works.)

25 mm dia uPVC Coupling

25 mm dia uPVC Elbow

25mm x 20mm uPVCReducer Tee

25mm uPVC Union

20mm uPVC Coupling

20mm uPVC Union

20mm uPVC Elbow

20mm x 15mm uPVC Reducer Tee

15mm Hex Nipple

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Departmental officers before use on work.

Fixing Gun Metal Gate Valve of dia 25mm

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Depatmental Officrs before use on the works)

Supplying and fixing of PVC water storage tank of best approved quality and make of super thick with lid of capacity of 1000 litres with accessories etc., complete as directed by the departmental officer. (The PVC water storage tank should be got approved by the Depatmental Officrs before use on work)

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Departmental officers before use on works)

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Departmental Officers before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Departmental Officers before use on works)

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Departmental Officers before use on works).

a.110mm dia PVC Elbow with door

b.75mm dia PVC Elbow with door

c.110mm dia PVC Plain bend

d.75mm dia PVC Plain bend

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower rose should be got approved by the Departmental Officers before use on works).

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Departmental Officers before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Departmental Officers before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Departmental Officers before use on woks)

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Departmental Officers before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

a.110 mm PVC Soil Pipe

b. 75 mm PVC Soil Pipe

Supplying, laying and jointing Glazed stone ware pipes of the following dia of approved quality with spigot and socket ends and fixing them in dry condition using spun yarn and cement including petty masonry shoring and strutting wherever found necessary and laying the pipe line in the alignment at the specified gradient and testing with necessary tools and plants, etc., and re-filling the trench with excavated earth and levelling the ground etc., complete complying with standard specifications. (Earth work excavation, re-filling with excavated earth will be measured and paid separately).

Supplying, laying and jointing Glazed stoneware pipes of following dia of approved best quality with spigot and socket ends (in reverse direction) in dry condition and laid in loose joints (i.e.) without cement and spun yarn, so that the waste water can be drained to the trenches already available, excluding cost of earth work excavation, cost of re-filling with crushed stone sand/ earth, but including laying the pipe in true alignment and gradient and conducting required water supply test for draining with necessary tools and plants, etc., complete complying with standard specifications.

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position 100 mm dia stoneware tee of approved best quality and provding leak proof joints with cement, spun yarn, etc., including dismantling the brick work and re-doing the dismantled portion to the original condition, etc., complete complying with standard specifications (The stoneware tee shall be got approved by the Executive Engineer before use on work)

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Brick work with Dry Bricks using country bricks of size8¾”x4¼”x2¾” for the following items including curing etc complete complying with standard specification.TNBP No : SS 31 and similar to 31C

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Supplying and laying of Interlocking Paver Block Stone 60mm thk. Over a base layer of sand filling incl. Cost of materials laying and Labour charges etc.,

Suppling and fixing of Single Phase 1.00 HP Centrifugal, Mano Block Pumpset 220 V, 50 H z, AC Power Supply ete with 25 mm dia Suction and 25 mm dia Delivery Pipes, with a Head Range of 15 m, complying with standard specification. and as directed by the Departmental Officers etc., complete.,

Refilling with Conveyed Gravel other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with GI Flush mounting box ,plastic combined cover plate and 6A One way modular type (one module) switch with light / fan marking and making good of the concealed portion with suitable color for concealed PVC light point (All switches ,cover plate and GI mounting box should be higher end company make (For light points) (Data-1)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with module GI switch box in flush with wall with 6A One way module switch with Module front plate light / fan marking and making good of the concealed portion with suitable color for concealed PVC light point / fan point (for electronic regulator) (For 6 points /coil) Higher end (Data-2)

Wiring with 3 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 1 modular plastic box with cover plate and 6A modular switch (two way) with painting of suitable colour for concealed PVC staircase light point (Data-3)

Supply and fixing of single box type 4'20W LED fitting with TW round blocks on wall or ceiling with with PVC unsheathed copper leads from terminals to the fitting (LED fittings should be of Higherend company make like philips /cromption etc) (Data -4)

Supply and fixing of surface mounted 5W LED fitting on wall or ceiling with connections(Data-5)

Supply and fixing of fancy lamp fittings with 9W LED bulb on wall with connections (SD-79)

Supply and fixing of foot lamp on wall with connections (Data-7)

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch(SD-105)

Supply and fixing of 48/45W LED street light fitting with pressure diecase Aluminium housing with IP 65 Protection with 25 mm dia G.I. pipe and bend class-B complete on wall with PVC unsheathed copper leads MS clamps and Aluminium painting LED fittings should be Higher end /philips make (SD-535)

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm downrod on the existing clamp (SD-110)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD-114)

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fanl (SD-120)

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch with combined module cover plate (plastic) on suitable module Concealed Box (GI ) in flush with earth connections. Higher End (SD-470)

Supply and fixing of 1no 16A switch mounted in suitable 1 module Metal flush mounted box with suitable plastic combined cover plate with Connections (Data-8)

Supply and fixing of 1no 16A plug mounted in suitable 2 module Metal flush mounted box with suitable plastic combined cover plate with Connections (Data-9)

Supply and fixing of 20A DP plug and socket sheet steel enclosure with 32A DP MCB in flush with wall with earth connection (AC Plug) (SD -144)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed on wall and ceiling with painting of suitable colour (Data-12)

Supply and run of 2 of 2.5 sqmm (36/0.3) PVC insulated single core unsheathed Copper conductor of 1100V grade in Suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm (36/0.3) PVC copper wire and making good of the concealed portion with suitable colour (SD-337)

Supply and run of 2 of 4 sq.mm (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm (36/0.3) PVC copper wire and making good of the concealed portion with suitable colour (SD-351)

Supply and run of 4 of 6 sq.mm (84 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm (36/0.3) PVC copper wire with painting of suitable colour(SD-358)

Supply and fixing of horizontal 3 phase 8 way distribution board of double door type with metal door with IP43 protection with 1 No 32A FP MCB switch as incoming and 24 Nos 6A-32A SP MCB as outgoing in flush with wall and making good of the concealed portion with suitable colour (The MCB DB and MCB's should be Legrand make) (Data-11)

Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing connection(SD-104)

Supply and fixing of 40A four pole RCCB Switch in a sheet steel enclosure suitable for 4 pole MCB switch including wall cutting, flushing and making good of the wall with earth connection (Data - 17)

Supplyand fixingof TNEB meter boardsuitable for 32A three phase service connection with 3Nos. 32A fuseunit (500V) 32A neutral link and earth link (1"x1/8" copper flat) on TW plank of size 600mmx450mmx19mm with supportingTW reepers of 1" thick aneither side with painting with suitable bolt and nuts for fixing theTW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Four Pole RCD / RCCB (Higher End) with suitable necessary connection (SD-128)

Supply and fixing of 3 phase 32A aerial fuse unit for 3 Nos. 32A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps (SD-135)

Supply and clamping of 4 × 16 sqmm PVC LTUG armoured aluminium cable with No.8 bearer wire supports on post or on wall with MS clamps (Data-13)

Supply and fixing of 65mm (2-1/2") dia G.I Pipe(class-B) of 6 mts length with 300mm x 300mm x 6mm base plate duly welded at the bottom with Concreting with Construction of masonary pedestal with necessary clamps to hold the LTUG Aluminium Service Cable with painting of suitable colour (Data-14)

Supply and run of 1 of No.8 SWG copper conductor on suitable PVC rigid pipe on wall with painting of suitable colour for earth connection (SD -371)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry(SD 211)

V.Chidambaram (BID ID -1335605)