REPAIR /MAINT TO VARIOUS PUMPS, MOTORS, CHLORONOME PLANTS, PUMP SET CONTROL PANELS AND CONNECTED WORKS AT JHANSI CANTT UNDER AGE E/M AT GE JHANSI

Amount

Dismantling and removing of centrifugal coupled / monoblock electric pump set of any make and capacity 0.5HP to 1.0HP from its installed position by disconnecting suction and delivery lines, fixing dummy plate to both suction & delivery pipe, disconnecting electrical cables, earth strips and dismounting the pump and motor from base channel for overhauling / repair / rewinding of motor etc and reinstalling back in its original position, checking alignment and testing on completion for satisfactory performance complete all as directed. Note: Re-winding and spare parts required for repair shall be measured and paid separately under relevant items.

All as per Item No.1 here-in-before but capacity 3.0 HP to 7.5 HP.

All as per Item No.1 here-in-before but capacity 10.0 HP to 15.0 HP.

All as per Item No.1 here-in-before but capacity 25HP to 30 HP.

All as per Item No.1 here-in-before but capacity 75HP to 100 HP.

Disconnecting the electric cable and water mains, lifting the submersible pump set of capacity 10 HP to 20 HP along with column pipe and submersible cable from shallow well having depth up to 20 mtrs for carrying out repairs / rewinding / replacement of defective submersible cable / replacement of rusted column pipe / flushing of bore well etc and re-installing and reconnecting the water mains and electric connections and testing for satisfactory performance complete all as directed. Note: Spare parts required shall be measured and paid separately under respective items.

All as per Item No. 6 here-in-before but capacity 25 HP to 40 HP.

Overhauling of pump set of any make by opening the pump and motor, replacing the worn out/defective spare parts, making good of shaft and shaft sleeve, cleaning internally, lubricating the rotating parts, re-assembling the pump and motor duly replacings all the packing material, worn out bolts, nuts, washers etc and testing for satisfactory performance of capacity 0.5HP to 1.0HP complete all as specified and directed . Note: (i) Quoted rate shall deemed to be inclusive of necessary packing material, nuts, bolts & washers etc. (ii) Spare parts replaced shall be measured and paid separately under relevant items.

All as per Item No.8 here-in-before but capacity 3.0 HP to 7.5 HP.

All as per Item No.8 here-in-before but capacity 10.0 HP to 15.0 HP.

All as per Item No.8 here-in-before but capacity 25HP to 30 HP.

All as per Item No.8 here-in-before but capacity 75HP to 100 HP.

All as per Item No.8 here-in-before but Submersible pump set of capacity 10HP to 20HP

All as per Item No.8 here-in-before but Submersible pump set above 25HP and up to 40 HP

Cutting and removing burnt out winding from electric motor of any make and rewinding with super enamelled copper winding wire of existing gauge and number of turns including varnishing, heating etc and testing for satisfactory performance of capacity 0.5HP to 1.0HP complete all as directed .

All as per Item No.15 here-in-before but capacity 3.0 HP to 7.5 HP.

All as per Item No.15 here-in-before but capacity 10.0 HP to 15 HP.

All as per Item No.15 here-in-before but capacity 25HP to 30 HP.

All as per Item No.15 here-in-before but capacity 75HP to 100 HP.

Cutting and removing burnt out winding from submersible electric motor of any make and rewinding with water proof poly wrapped copper winding wires of existing gauge and number of turns and testing for satisfactory performance of capacity 10.0 HP to 20HP complete all as directed by Engineer-in-Charge.

All as per Item No.20 here-in-before but capacity 25 HP and up to 40 HP

Supply only the following spare parts suitable for centrifugal / monoblock pump sets and motors of any make as per sample for existing model of pump sets:-

Ball bearing of size 6202/6201or suitable for up to 0.5 HP to 1.0 HP pump set. Make- TATA/NBC/SKF

Ball bearing of size 6206/6306 or suitable for above 3.0 HP to 7.5 HP pump set .Make- TATA/NBC/SKF

Ball bearing of size 6307/6308 suitable for above 10 HP and up to 15 HP pump set. Make- TATA/NBC/SKF

Ball bearing of size 6309 or suitable for above 25 HP and up to 30.0HP pump set.Make- TATA/NBC/SKF

Ball bearing of size 6307/3307 or suitable for 75 HP and up to 100 HP pump set. Make- TATA/NBC/SKF

Cover Bush

Cable connection terminal plate suitable for 75 HP to 100 HP motor

External fan plastic body suitable for up to 30 HP motor

External fan plastic body suitable for 75 HP to 100 HP motor

CI Impeller with key suitable for 75 HP to 100 HP pump

Metallic Coupling suitable for 25 HP and up to 30.0HP pump set

Metallic Coupling suitable for 75 HP and up to 100.0HP pump set

Coupling Rubber No-TC 16/17

Coupling Rubber No-TC 13

Water seal of size 35mm or suitable for 25 HP to 30 HP

Water seal of size 50mm or suitable for 75 HP to 100 HP

Supply only the following spare parts suitable for submersible pump and motors of any make as per sample for existing model of pump sets:-:-

SS Rotor Sleeve suitable for submersible pump set of 10 HP to 40HP

GM Housing Bush suitable for submersible pump set of 10 HP to 40HP

Thrust bearing suitable for submersible pump set of 10 HP to 40HP

Water seal suitable for submersible pump set of 10 HP to 40HP

Stud, Nut & Bolt suitable for submersible pump set of 10 HP to 40HP

SS Impeller shaft suitable for submersible pump set of 10 HP to 40HP

SS Impeller suitable for submersible pump set of 10 HP to 40HP

Shaft sleeve suitable for submersible pump set of 10 HP to 40HP

Neck Ring suitable for submersible pump set of 10 HP to 40HP

SS Coupling assy with key suitable for submersible pump set up to 40 HP

Strainer suitable for submersible pump set up to 40 HP

Supply and connecting of 3 core x 6 sqmm Flat copper conductor cable 1100 Volts grade, PVC Insulated & PVC Sheathed conforming to IS- 694/1990 for submersible pump set complete all as specified and directed. Make- Havells/Finolex/Polycab/KEI

Supply and connecting of 3 core x 10 sqmm Flat copper conductor cable 1100 Volts grade, PVC Insulated & PVC Sheathed conforming to IS- 694/1990 for submersible pump set complete all as specified and directed. Make- Havells/Finolex/Polycab/KEI

Material and labour for preparation of old painted surfaces of pump and motor and applying two coats of spray paint of approved colour with enamel paint as per colour coding as specified and directed by Engineer-in-charge for capacity of pump set from 10 to 30HP.

All as per Item No.26 here-in-before but capacity 75 to 100 HP .

Material and labour for preparation of new or previously untreated/old painted steel surfaces of water pipe lines of any size, in any position, with two coat of synthetic enamel paint of approved colour including marking direction & name of feeder, complete all asspecified and directed.

Supply, fabricating and fixing of MS clamp, base frame for pumping set, supports, bracing, stiffness etc made out of MS channel, angle iron, flat iron of any size including welding/drilling of holes with and including nuts, bolts and washers etc, as required, including painting with two coats of synthetic enamel paint over a coat of red oxide paint complete all as directed.

Supply, installation, testing and commissioning of borewell submersible pump set suitable for 100mm dia delivery pipe , electric driven with 3 phase, 415 volts, 50 Hz, copper wound submersible electric motor coupled with submersible multistage pump suitable for discharge 1350 LPM at a head of 55m with bronze impeller, CI bowl, SS casing & SS pump and motor shaft complete including disconnecting all electrical and water connections and taking down of existing unserviceable pump set and depositing to MES E/M store yard complete all as specified and directed by Engineer-in-charge. Make : Kirloskar / KSB / CG

Supply and fix in replacement of CI Butterfly valve of size 80mm nominal bore as per IS 13095 , PN 16 , wafer type without lugs, suitable for clamping between flanges as per ANSI B 16.1 Cl-125, including flanges, fittings, gasket, nuts, botls , washers etc including taking up / down of existing unserviceable butterfly valve of any description complete all as specified and directed. Make : Leader/ Crawley/ Audco/ L&T

Supply and fix in replacement of CI Butterfly valve of size 100mm nominal bore as per IS 13095 , PN 16 , wafer type without lugs, suitable for clamping between flanges as per ANSI B 16.1 Cl-125, including flanges, fittings, gasket, nuts, botls , washers etc including taking up / down of existing unserviceable butterfly valve of any description complete all as specified and directed. Make : Leader/ Crawley/ Audco/ L&T

Supply and fix in replacement of CI Butterfly valve of size 150mm nominal bore as per IS 13095 , PN 16 , wafer type without lugs, suitable for clamping between flanges as per ANSI B 16.1 Cl-125, including flanges, fittings, gasket, nuts, botls , washers etc including taking up / down of existing unserviceable butterfly valve of any description complete all as specified and directed. Make : Leader/ Crawley/ Audco/ L&T

Supply and replacement of Cast Iron sluice valve of size 200mm dia bore, having pressure rating PN 1.0, double flanged, non-rising stainless steel spindle with iron wheel conforming to IS:14846-2000 with jointing material ie new rubber gasket, nuts & bolts, washer etc of suitable size and taking down old unserviceable sluice valve complete all as specified and directed. Make: Kirloskar / Leader / L&T

All as per item No. 36.00 here-in-before but of size 150mm dia bore.

All as per item No. 36.00 here-in-before but of size 100mm dia bore.

Supply and replacement Cast Iron Non Return Valve (NRV) 200mm NB with flanged ends swing type / ball type ISI marked including replacement of necessary packing material, bolts, nuts and washers complete all as directed. Make: Kirloskar / Leader / L&T

All as per item No. 39 here-in-before but of size 150mm NB.

All as per item No. 39 here-in-before but of size 100mm NB.

Supply and replacement Cast Iron foot valve flanged end / screwed end ball type/ swing type ISI marked including replacement of necessary packing material, bolts, nuts and washers of size 200mm dia complete all as directed. Make: Kirloskar / Leader/ L&T

All as per item No. 42 here-in-before but of size 150mm NB

All as per item No. 42 here-in-before but of size 100mm NB

Note for item No 33 to 44:- Material will be accepted and allowed to incorporate in the work only after production of proper purchase voucher from authorised dealer and test certificate from the manufacture.

Supply and fix in replacement HBC fuse link of capacity 200A, 415V, 50 Hz, 80 KA, type B2 complete all as specified and directed. Make:- Havells/C&S/ L&T

S&F in replacement of contactor of 200 amp capacity, AC3 rating, 03 pole, coil voltage 415V, 50 Hz, suitable for 100 HP motor-pump set, compatible with soft starter confirms to IS/IEC 60947-4-1 & IEC 60947-4-1, complete all as directed. Make : L&T / Schneider Elect / Siemens / ABB

Supply, installation, test and commissioning of Soft Starter for soft starting and stopping of 100HP electric motor Max. current Rating 125 Amps, 3P, Voltage rating 415 V (+ 10% - 15%) and 50/60 Hz with provision of inbuilt Bypass Contactor, Soft start / Soft stop / Adjustable current limit, essential motor protections against Overload, Single phasing, Phase sequence reversal, Abnormality in supply, Unbalanced current, Thermistor protection through PTC, Excess start time setting including taking down of existing unserviceable starter of any description complete all as specified and directed. Make : Schneider(ATS48C14Q) / ABB ( PST142-600-70 SERIES) / Siemens (3RW4055-6BB44) / L&T(CSXi-075-41)

Supply and fix in replacement MCCB TP 250A, 415V, 50 Hz, 37 KA complete all as specified and directed. Make- C&S Electric, Product No-CSC4S3 or equivalent

Supply and fix in replacement MCB TP 63A, C-Series , 415V, 50 Hz, 10 KA complete all as specified and directed. Make- C&S Electric, Product No-CSMBS3C63

Supply and fixing column pipe 100 mm bore having length of each pipe 3 mtr long made out of GI pipe , heavy duty with flange end both side with suitable rubber gasket , nut & bolts including taking down of existing unserviceable GI pipe of any description complete all as specified and directed. Make : Tata/ Jindal/Prakash/ Surya/ Zenith

Supply and fix in replacement of Electrically operated, Butter fly valve, long neck type suitable for pipe of size 150mm dia, PN 16, made out of Al alloy complete all as specified and directed.

Supply and fix in replacement of Pressure gauge suitable for 0.5 HP pressure pump complete all as specified and directed.

Supply and fix in replacement of Pressure tank suitable for 0.5 HP pressure pump complete all as specified and directed.

Supply and fix in replacement of Auto pressure pump relay suitable for 0.5 HP pressure pump complete all as specified and directed.

Supply and fix in replacement of Self priming monobloc pump set of capacity 0.5 HP, single phase, 3000RPM, 6-30M head with 2600-600LPH complete with fixing arrangement for pressure gauge and pressure tank including taking down existing unserviceable pump and depositing to MES E/M store yard complete all as specified and directed.

Supply and fix in replacement of Brass foot valve complete all as specified and directed for the following sizes:- Make : Zoloto/ Sant/ Leader

50mm dia

25mm dia

M/s Jagdish Chandra Arora