PROVISION OF STATION GYM AT NO. 2AFSB UNDER AGE (I) AF STATION CHIMNEY HILLS BANGALORE

Amount

Surface exv n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil.

Excavation in trenches, n. exc.1.5m wide and n.exc. 1.5m deep; for foundation etc n.exc.10 Sqm on plan and getting out hard / dense soil.

M&L PCC 1:4:8 type D-2 (using 40mm graded agg) in foundation, filling and mass concrete.

Stone walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6

M&L PCC (1:2:4) type B0 as in DPC to horizontal or vertical surfaces incl necessary form wk etc. 40mm th all as specified incl water proofing compound.

Supply only integral water proofing compound of approved make.

Moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and rammed incl watering.

M&L hardcore of guage n.exe 63mm, deposited,spread and levelled in layers n.exe 15 cm thick,watered and rammed in two layers a true surface .

M&L 75 mm thick PCC type B-1, 1:3:6 (40 mm graded aggregate) as in sub base.

M&L for providing 100 mm thick Cement Concrete type B-1, 1:2:4 (20 mm graded stone agg) as in floor etc,

M&L Precast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks exc 10 cm in width and setting in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L RCC type B1 1:2:4 (20 mm graded stone aggregate (nominal mix) in beams, cantilevers, bressummers, lintels over 1.5 m span

M&L for treating the bottom & sides of excavation at the rate of 5 ltrs of emulsion per square metre of surface area.

M&L treating the backfill in contact with fdn at the rate of 7.5 ltrs of emulsion per suare metre of vertical surface (Area of the sub structure in contact with backfill to be measured ).

M&L treating the top surface of filled earth at the rate of 5 ltrs of emulsion per square mtr of surface.

M&L treating the soil along with external perimeter of bldg at the rate of 2.25 ltr of emulsion per mtr of the perimeter wall.

Returning filling incl spreding leveling watering and well ramming in layout n. exc. 25cm in soft and loose soil.

Removal of excavated material n. exc.50mtr and depositing where directed at a level n. exc. 1.5m above the starting point all as specified and as diercted.

M&L for TMT bar 10mm dia & over cut to length ,bent to shape required incl cranking , bending , hooking, for lintel and binding with MS wire not less than 0.9 mm dia or securing with clips.

As per item no above but 6 to 8mm dia.

As per item no above but 5 to 10 mm dia as in stirrups.

Formwork to edges of fair finished surface of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide.

M&L Rubber tiles with fabric backing or insert, plain coloured or marbled topping, matt or glossy, laid in floors with approved adhesive complete all as specified and all as specified and as diercted.

S&F Non - skid Ceramic colouerd tiles 7 to 8 mm thick (square/ rectangular) of each tile exceeding 0.18 sqm but n exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20 mm thick screed bed or bedding layer of mortar 1:4.

S&F Glazed ceramic coloured tiles in verticle surfaces 350 x 250 x 7 / 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick backing coat in CM 1:3.

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain coloured PVC sheet reinforced with M.S Square tubes, supporting & fixing in opening as per specification all as specified and as diercted.

S&F factory made solid PVC Moulded door shutter ,30 mm thick (style)consisting of frame made out of MS tubes for top & Bottom rail , MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC sheet for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail : panelling of both side prelam PVC sheet to be fitted in the ms frame welded/sealed to the stiles & rails with suitable PVC seat beading ,and jointed together with solvent cement ,supplying and fixing in the frame at site as per specified and directed by Engr-in-Charge.

S&F Butt hinges, medium weight cold rolled mild steel 100 mm in size.

S&F Aluminium alloy, anodised, sliding door bolt 150 mm in length, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy.

S&F Aluminium anodised, barrel tower bolts of extruded section, 100 mm in length.

S&F Aluminium handles, cast type 75 mm in size.

S&F fancy type chromium plated stop valves cast copper alloy screwed down high pressure with crutchor butterfly handle screwed both ends for iron pipe or for union 15 mm dia bore and fixed

S&F 15 mm dia bore pipe chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 Liters low level , white, with inlet, ball valve, float and handle including brackets and PVC connections 15mm size with PTMT nuts of length 600mm.

Cutting chases in brick wall, pinning in. making good to facing where required and pointing in cement mortar 1:3 to ends or edges of cills etc,. and cutting chases for concealed water tubing etc., and making good , cutting not exc 10 cm in girth and S& F 40 mm outer diameter of high density polyethlene pipes (HDPE) of pressure rating 6khf/cm² laid in trenches.

S&F 75 mm dia of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as diercted.

S&F Towel Rail 600mm long of PTMT fixed with screws and wooden/plastic cleats. (Minimum weight 190gms)

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), complete all as specified and as diercted.

S&F for soap dish holder. Make: Jaquar, Cat I. No. AKP-35731P.

S&F Counter top WHB vitreous china oval type coloured with brackets fitted on granite counter top.

M&L for pre- polished granite slab Jet black machine cut of any shade as approved by GE of 18 to 20mm thick including necessary notching, chamfering the edges at factory, laid over and including 20mm thick cement screed bed in CM 1:4 including Cutting, Grinding and Mirror polishing(Granite finish) with suitable grinding stones in single piece for cooking platform complete all as 'specified and as directed.

S&F fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long shanks and fly-nuts, screwed for iron pipe.

S&F Waste coupling of PTMT (half or full thereaded) 32 mm in dia of pipe and Waste fittings 32 mm for WHB.

S&F for PVC connections 15mm size with PTMT nuts of length 600 mm.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long including stainlells steel F clamp complete all as 'specified and as directed.

S&F PVC Rotational moulded polyethylene water storage tanks 500 Liter (cylindrical vertical with closed top) hoisted and fixed in position all as specified

S&F Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed , bore of pipe 20mm.

S&F 'Medium grade' galvanised Tubes 15 mm dia, with all tube fillings (such as bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc.) and fixing complete with clips, wall hooks, wooden plugs, or laying in trenches, etc., fitting and fixed complete to walls and ceilings or laid in floors.

S&L ' Medium grade' galvanised Tubes 20 mm dia, with all tube fillings (such as bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc.) and fixing complete with clips, wall hooks, wooden plugs, or laying in trenches, etc., fitting and fixed complete to walls and ceilings or laid in floors.

S&F PVC (SWR) pipe single socketed in any length with rubber ring joints laid in floor or trenches 110 mm bore pipe.

S&F PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls 110 mm bore pipe.

S&F PVC (SWR) bends any radius 110 mm bore pipe.

S&F 110 mm PVC (SWR) vent cowl.

Cutting in to existing man holes for connecting new drains for internal dia of pipe 100mm, making good to pipe and rendering, cutting out existingbenching for and forming branch channel (1/2 round or 3/4 section) in cement mortar 1:2:4 type B1 smooth finished and reforming benching a srequired complete all as directed.

M&L for 12 mm thick tiles for insulation and accoustic purposes, 60x60 cm in size, staples on aluminium snap grid in ceiling including anodised aluminium snap grid frame work and hangers 6 mm dia GI (up to 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40x3 mm size 60mm long including one coat of distemper over a coat of primer complete all as specified.

S&F collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc as specified, erected in position and securing runners with holdfasts and brackets complete.

Rendering 15 mm thick on fair faces of brick work or concrete surface in cement plaster 1:4

Rendering 5 mm thick on fair faces of brick work or concrete surface to ceiling cement plaster 1:3

Rendering 20 mm thick on fair faces of brick work or concrete surface cement plaster 1:6

M&L keyed pointing to random or polygonsl rubble, uncoursed or brought upto courses in CM 1:3.

S&F Aluminium Anodised door with frame using aluminium section of size 63.50x38.10x1.95mm thick (single Groove) and shutter consisting bottom and middle rail using aluminium section of size 114.30x44.45x2.15 mm thick , top rail using aluminium section of size 83.50x44.45x2 mm thick ,vertical style using aluminium section of size 85x44.45x1.80 mm thick with 6mm thick black tinted glass insert to full shitter including aluminium andised handle of size 200mm long 02 nos ,150mm tower bolt - 01 no glazing clip size 19x17.30x1.20 m thick ,rubber ring/gasket/beading sliding /dead lock 6 lever size 100 mm etc complete all as specified and directed ,

M&L for aluminium anodised powder coated windows with 3 channels for catering mosquito proofing &4mm thick glass with necessary accessories like jointing cleats, rubber packing,beading and screws etc complete,including powder coated aluminium grill of DG-103 as per TD drg no AFB/TD/352/11,Sheet 1/2 & 2/2 and AFB/TD/237/05,Sheet 1/1

M&L aluminium anodised powder coated ventilator with 4mm thick tinted glass with movable/ adjustable system incl necessary accessories like jointing cleats, rubber packing,beading and screws etc complete all as specified.

S&F for steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.or induction butt welded to angles, cleats conforming to I. S.1161-1979 grade St.-240

S&F for pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M&L for preparation of new untreated steel surfaces of any description over 10 cms width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide, zinc chrome primer complete all as specified

M&L for preparing newly plastered or unplastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer on internal walls surface.

M&L for preparing newly plastered or unplastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer on ceilings.

M&L for preparing newly plastered or unplastered surfaces and applying two coats of anti fungal weather proof paint over a coat of alkali resistant primer on external wall surface.

M&L for 75 mm thick PCC 1:3:6 type C-1 (using 20mm graded mechanically crushed stone aggregate ) for plinth protection ,finished even and smooth without using extra cement ,including necessary constructions joint filled with seailing compound all as specified.

Surface excavation not exceeding 30 cm and averaging 15 cm deep and getting out in hard/dense soil

M&L for Hard core gage n.exc 63mm deposited,spread ,levelled in layers n.exc 15 cm thick,watered and rammed to a true surfaces.

M&L for PCC 1:4:8type D-2( using 40mm graded stone aggrigate) as in Sub base 75mm thick

M & L for screed bed or bedding layers of motor 15mm thick in CM 1:6 for laying floor finishes.

M & L for chequred cement concrete tiles of size 30cm x 30cm x 20mm thick with gray cement and pigments,jointed and pointed in neat cement slurry in floors.

Removal of surplus soil to a diatence n.exc 50m and depositing where directed.

M&L for Point wiring with 1.5 sqmm, single core ,PVC insulated, unsheathed FRLS cable, 1100 volts grade, IS -694 marked, with multi stranded copper conductor and earth continuity copper conductor cable of 1.5 sqmm as in phase/neutral and connected to common earth dolly drawn through and including rigid PVC conduit of suitable size alongwith fittings and accessories, fixed /laid/concealed in walls/ceilings including cutting chases and making good to walls, floors etc, and also incl suitable modular bottom sunk type pressed steel terminal box and suitable modular top cover with frame and No of modules for the following complete all as specified and directed :- (a) One light/fan point controlled by one, one way switch complete all as specified and directed

All as per item No. 79 above but one three pin socket outlet 5 Amp controlled by one, one way switch on independent board complete all as specified and directed

All as per item No 79 herein before but with 2.5 sqmm and 2.5 sqmm as earth conductor on independent board for 15 Amp socket outlet controlled by one , one way switch on independent board complete all as specified and directed

Supply and fix Modular switch 1 way 6A,1 module complete all as specified and as directed.

Supply and fix Modular switch 1 way 16A,1 module complete all as specified and as directed.

Supply and fix Modular socket 6A 2 /3 pin combined 2 module complete all as specified and directed

Supply and fix Modular socket 6/16A 2 /3 pin combined 2 module complete all as specified and as directed.

Supply and fix ceiling rose 3 Phase / PVC/ Polycarbonate, isolated body complete all as specified and directed

Supply and fix modular fan regulator, 120W - 2 module for ceiling fan 1200 /1400 mm sweep complete all as specified and directed

Supply & fixing ceiling fan complete with accessories 230 V,1200 mm sweep, Matt white colour complete all as specified and directed

Supply & fixing exhaust fan, AC single phase 230/ 240 V of size 300 mm sweep with birdguard to protect the fan in running condition complete all as specified and directed.

S&F regal battten T8 1X18 watt complete with all accessories prewired incl crystal glass LED tubelight (double side connection) complete all as specified and directed

S&F surace and wall mounted LED batten with aluminium housing & integrated electronic driver of 10 watt (2 ft) complete all as specified and directed

S&F distribution boards protection class IP-43, 240 V, double door suitable for mounting MCB with min 200 Amps rating bus bar SPN 12 way complete all as specified and directed

S&F MCB, 240 V, 50 Hz, breaking capacity 10 KA, confirm to IS/IEC 60898-1, C' series type of following capacity complete all as specified and directed (a) SP 6 to 32 Amps

All as per item No. 93 above but SPN 40 Amps/63 Amps

M&L for circuit wiring with PVC insulated, single core, multi stranded, 1100 volts grade unsheathed copper conductor cable in and including PVC Conduit/Casing capping with accessories fixed on wall /ceiling with GI screws complete with 2 runs of 4 sq mm and one run of 4 sqmm for earth continuity conductor all as directed. (for AC)

S & F sheet metal enclousure 2 in 1 3pin metaliic socket and plug top with plug socket and MCB 20 Amp SPN

Supply and fix surface mounting LED flat panel, 35 W, 2" X 2" size, aesthetically designed and glare free symmertical illumination and complete all as specified and directed .

M&L for earthing with galvanised iron earth plate electrode 600mm x600mmx 6mm thick burried directly in ground (Earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of earth plate not less than 1.5 metres below normal ground level, connected to galvanised iron wire of 4 mm dia connected to earth plate electrode by means of bolts,nuts, check nuts and washers,earth wire protected with and including 15 mm bore medium grade GI pipe all as shown in electrical plate no 3 of MES schedule part-1, with and including PCC 1:3:6 type C1 pit with cover of RCC 1:2:4 type B1, reinforced with welded steel wire fabric not less than 4 kg per sqmtr with handle and angle iron frame, watering arrangement with 20 mm bore GI medium grade pipe, GI funnel with wiremesh, filling with mixture of common salt and charcoal, necessary excavation, refilling, removing away soil and earth work in any type of soil, testing and commissioning complete all as specified and directed .

Supply and lay LT under ground cable XLPE insulated armoured heavy duty 1100V grade with multistranded/solid aluminium conductor confirming to relevant IS in trenches, ducts, through pipes fixed to wall etc all as directed including cable gland, terminal socket and connecting up of size 16 sqmm 2 core including dismantling of old U/S cable

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in hard/dense soil for laying/repair of cable.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm thick.

Removing excavated materials to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

Supply and lay brunt bricks class 'B' of standard size in trenches for protection of UG cable.

M&L for sand cushioning in trenches spreading and consolidation 8cm thick before laying the cable & 15 cm of sand after laying the cable complete all as specified

ANAND REFRIGERATION

M/s A N Kalbhavi