Construction of Community Trade Mart Building at LCS Chhupan Near Shipkila District Kinnaur (HP) (SH- Building portion, WS and SI, Septic Tank, Rain water harvesting system and site development

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains , including dressing of sides and ramming of bottoms, with in all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within all leads in all kind of soil, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas including getting out and disposal of excavated earth upto all lead and lifts, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, out the excavated soil, and then returning the soil as required, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, Pipes, cable etc, not exceeding 80 mile meter dia.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc., consolidation each deposited layer by ramming and watering, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (One Cement : four coarse sand: eight graded stone) aggregate 40 mm (forty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form for all hight : Walls including attached pilasters,, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Supplying and filling in plingh with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Boulder filling under floor, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (One Cement : three coarse sand: six graded stone) aggregate 40 mm (Forty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (One Cement : three coarse sand: six graded stone) aggregate 20 mm (Twenty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm (Twenty millimeter ) nominal size over 75mm (Seventy millimeter) thick bed of dry brick ballast 40 mm (forty milimeter) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :150 mm diameter S.W. pipe including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form for all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Foundation of footing

Shelves

Lintel, Beams, Plinth beams, Girders, Cantilever etc.

In Front stairs

Small lintels , moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Suspended floors roofs, landings, balconies and access platform

Edges of slab and breaks in floors and walls under 20cm wide.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. fan type I or II of 16mm dia (sixteen milimeter diameter) M.S. Bar bend to shape with hooked ends in RCC slabe or beams during laying, including painting the expose portion of loop, all as per standard desizen complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20mm (Twenty millimeter )nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (one cement : two coarse sand : four graded stone) aggregate 20 mm (twenty millimeter) nominal size), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (one cement : one point five coarse sand : three graded stone ) aggregate 20 mm (twenty millimeter) nominal size, in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (one cement : one point five coarse sand : three graded stone ) aggregate 20 mm (twenty millimeter) nominal size, in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg (kilogram) per square metre on damp proof course after the surface with brushes and finally with apiece of cloth lightly soaked in kerosenecleaning oil, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing woodwoork in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position. 2nd class deodar wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying 20 cm (centimeter) thick composit stone masonry with stone facing of chisel dressed stone one line dressed in cement : 6 sand) and backing with cement concrete 1:3:6 concrete ( 1 cement : 3 sand : 6 graded stone sggregate 20 mm (Twenty millimeter) nominal size on inner face of walls including centering, shuttering and propping complete up to floor two level. ncluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.ncluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (one cement : four coarse sand) for hydrants, with C.I surface box 350 X 350 mm top and , 165 mm (one hundred sixty five milimeter) deep ( inside) with chained lid and RCC top slab 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimeter) nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (one cement :five fine sand : ten graded stone aggregate 40 mm (forty milimeter) nominal size) and inside plastering with cement mortar 1:3 (one cement : three coarse sand) 12 mm (twelve milimeter) thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing weepholes in brick masonry/stone masonry/plain reinforced concrete abutment, wing wall, return wall with 100 mm (one hundred millimeter) dia PVC pipe extending through the full with of the structures with slop of 1 (v):20 (H) ( one vertical : twenty horizontal) towards drawing face complete as per drawing and technical specification clasuses 614,709,1204.3.7, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm (twelove millimeter) thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Inside size 90x80 cm (ninety into eighty centimeter) and 45 cm (forty five centimeter) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimeter)internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg (twenty three killogram )and weight of frame 15 kg (fifteen killogram) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm (one hundred twenty into ninrty centimeter) and 90 cm (ninety centimeter)deep including C.I. cover with frame (heavy duty) 560 mm (five hundred sixty millimeter) internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (twenty millimeter) nominal size upto plinth level with : Cement mortar 1:6 (one cement : six coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (one hundred into one hundred into sevrnty five millimeter)inside with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Cutting chases in brick masonry walls for following diameter and cast iron/centrifugally cast (spun) iron pipes and making good the cement concrete 1:3:6( 1 cement : 3 coarse sand : 6 graded stone aggregate 12.5 mm (twelove point five millimeter) nominal size, including necessary plaster and pointing in cement mortar1:4(1 cement : 4 coarse sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

100mm (one hundred millimeter) dia

75mm(seventy five millimeter) dia.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters, 35 mm (thirty five millimeter) thick including ISI marked Stainless Steel butt hinges with necessary screws, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing plain square edge cover fillets (Beading) 40mmx12mm (Forty millimeter into Twelve millimeter) section with wood screws in ceiling and lining including mitring at junction, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 18 mm (eighteen millimeter) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimeter) thick base cement mortar 1:4 (one cement : fou rcoarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm (square meter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railing, brackets, gates and similar works, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing 40 X 5 mm ( forty in five millimeter) flat iron fast 40 cm (forty centimeter) long including fixing to frame with 10 mm (ten millimeter 0 diameter bolt, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimeter) 1:3:6 mix (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm (twenty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 19mm (Nineteen millimeter) thick commercial board water proof in sheleves/box for cup board with butt joints & fioxing with nails & screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 19mm (Nineteen millimeter) thick commercial board water proof shutters fir up boards i/c fixing with nickel plated piano hinges with screws etc. complete), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing water proof kit ply of standard quality ISI mark and approved shade and colour in panelling & wall linning i/c mitring at jointing and nails complete (frame work base to be measured and paid separately) 9mm (nine milimeter) thick ply, including priming coat on unexposed surface and carriage of material through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hundred millimeter) sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred forty millimeter) with integral, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimeter) C.P. brass pillar taps, 32 mm thirty two millimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White vitreous China basin size 550x400 mm(five hundred fifty into four hundred millimeter) with a pair of 15mm (fifteen millimeter) C.P. brass pillar taps, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer-in-charge.

Providing and fixing PVC waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm (forty millimeter) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimeter) gap for thermal expansion, (i) Single socketed pipes , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing in positionpre-cast R.C.C manhole cover and frame of required shape and approved quality LD-2.5 Circular shape 450 mm (four hundred fifty millimeter) internal diameter , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 75mm (seventy five millimeter) dia PVC cowl, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing high pressure PVC spogot and socket, waste and ventilating pipe ISI marked fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110mm(one hundred ten millimeter) dia.

75mm(seventy five millimeter) dia.

Providing and fixing PVC clamps ISI marked of adhesive design with steel screws and rawl plugs etc, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110mm(one hundred ten millimeter) dia.

75mm(seventy five millimeter) dia.

Providing and fixing PVC single equal branch with oval door, ISI marked insection rubber washer 3mm (three millimeter) thick bolts and nuts complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110mm(one hundred ten millimeter) dia.

75mm(seventy five millimeter) dia.

Providing and fixing PVC plain double equal branch , ISI marked complete including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110mm(one hundred ten millimeter) dia.

75mm(seventy five millimeter) dia.

Providing and fixing PVC door bend with ovalaccess door, insertion rubber washer 3 mm (three millimeter) thick bolts and nuts ISI marked complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110mm(one hundred ten millimeter) dia.

75mm(seventy five millimeter) dia.

Providing and fixing PVC collars ISI marked including fixing with aprooved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110mm(one hundred ten millimeter) dia.

75mm(seventy five millimeter) dia.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors, 110 mm x 75 mm (one hundred ten into seventy five millimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm (five centimeter) to 20 cm (twenty centimeter), in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Providing and fixing 50 mm (fifty millimeter) special quality bright finished brass cupboard or ward robe locks with four levers of approved quality inculding necessary screws etc. complete, , complete as per direction of the Engineer-in-Charge.

Providing and fixing 50 mm (fifty millimeter) bright finished brass cupboard or ward robe knob of approved quality inculding necessary screws etc. complete, , complete as per direction of the Engineer-in-Charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm( seven hundred one millimeter to one thousand millimeter), with double speed adjustment with necessary accessories and screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less then AC 10 as per IS: 1868, transparent or dyed to required colour or, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

300 X 16 mm (three hundred into sixteen millimeter)

250x16mm (two hundred fifty into sixteen millimeter)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade, with necessary screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

250x10 mm (two hundred fifty into ten millimeter)

150x10mm (one hundred fifty into ten millimeter)

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not lrss than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

125mm (one hundred twenty five millimeter)

100mm (one hundred millimeter)

Providing and fixing aluminium hanging floor door stopper, ISI marked anodised (anodic coating not lrss than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete (twin rubber stopper),including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete (triple strip vertical type),including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & Fixing decorative high pressure Iaminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S, including cost of adhesive of approved quality (1.00mm thick) as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing factory made upvc windows frame and shutter are in all complete. Casement cum fixed panneled window having both and single casement panel, Middle fixed panels and at top completely fixed ventilater with S.S. friction hings (350x19x1.9) made of ( big series) frame 67x60mm (sixty seven into sixty milimeter) sash 67x80mm (sixty seven into eighty milimeter) as muellion 67x80mm (sixty seven into eighty milimeter) all having wall thickness of 2.3±0.2mm and single glazeing bead/double glazing bead of appripriate dimension (Area of window above 3.00 square meter upto 5.00 square meter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hosting, fixing in position and priming coat of approved steel primer all complete, ,including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimeter) gap for thermal expansion, (i) Single socketed 110mm (one hundred ten millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised- PVC mouldrd fitting/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimeter) gap for thermal expansion, (i) Single tee with door 110x110x110mm (one hundred ten into one hundred ten into one hundred ten millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised- PVC mouldrd fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimeter) gap for thermal expansion, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Coupler 110 mm ( one hundred ten millimeter)

Singlr pushfit Coupler 110 mm ( one hundred ten millimeter)

Bend 110 mm (one hundred ten millimeter)

Constructing soak pit 1.20 x 1.20 x 1.20 m (one point twenty into one point twenty into one point twenty meter )filled with brickbats including S.W. drain pipe 100 mm (one hundred) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, staircase railing and similar works, including applying priming coat of approved steel primer, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class drodar wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing plain skirting with butt jointing and screws (frame work and cover fillets to be measured and paid for separately) with 25mm (twenty five millimeter) thick 2nd class deodar wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster on rough side of single or half brick wall of mix: 1:6 (one cement: six coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

6 mm (six millimeter) cement plaster of mix 1:3 (1 cement : 3 fine sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Kota stone slab flooring over 20 mm (twenty millimeter) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Kota stone slab flooring over 20 mm (twenty millimeter) thick in steps, skirting, dado and pillars laid on 12 mm (twelove millimeter) average thick cement mortar 1:3( 1 cemrnt : 3 coarse sand) and joined with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make in colours such as white, lvory, Grey, Fume Red Brown, laid on 20mm (twenty millimeter) thick cement mortar 1:4(1 cement : 4 Coarse sand), jointing with greycement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigment etc., complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in colours , shades except burgundy, bottle breen, black of any size as approved by Engineer-in - charge in skirting, risers of steps and dados over 12 mm (twelove millimeter)thick bed of cement mortar 1:3(1 cement : 3 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing in white cement mixed with pigment of matching shade complete., complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.60mm (zero point sixty milimeter) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron Jor L hooks, bolts and nuts 6mm dia (six milimeter diameter)with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm (sixty centimeter) overall in plain G.I. sheets fixed with galvanised iron J or L hooks, bolts & nuts 8mm (Eight millimeter) dia limprt and bitumen washers complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing valleys 0.63 mm (zero point sixty three millimeter) thick 90 cm (ninty centimeter) over all in plain G.I. sheets fixed with galvanised iron J or L hooks. bolts and nuts 8mm (eight millimeter)dia G.I. limpet bolts and nuts 8mm (eight millimeter) dia G.I limpet and bitumen washers, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.63 mm (zero point sixty three millimeter) thick 30 cm (thirty centimeter) wide 12 cm(one hundred twenty centimeter) over all semicircular plain G.I. sheet gutter with iron brackets 40 x3mm (forty into three millimeter) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing MS BP sheet 1.66 mm (one point sixty six millimeter) to 20mm (twenty millimeter) thick in eaves board/ facia and etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing polycarbonated tranparent sheet 1.20mm (one point twenty millimeter) thick in roofing with galvanised J or L hooks bolts and nuts with G.I Limpe and bitumen rubber washer complete with all accessories as required as per direction of Engineer-in-charge.

Providing and fixing 12 mm (twelove millimeter)thick wooden plank ceiling with planks over lapping each other and jointed with wood screws (frame work to be paid for separately). 1st class deodar wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing bright finished brass single acting spring hinges with necessary brass screws etc. complete :all complete as per the direction of Engineer-in-charge,

Providing and laying 60mm (sisty milimeter) thick faciory made cement concrete interlocking paver block of M -30 grade made by block making vibratory compactory compaction, of approved size, design & shape, laid machine with strong required colour and pattern over and including 50mm (fifty milimeter) thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge,

Particle board bwp phenol bonded exterior/interior grade in partitions.all complete as per the direction of Engineer-in-charge,

Providing and fixing frame work for main wall/ partitions etc. made of 60x60x3.6 mm (sixty into sixty into three point six millimeter ) MS square holow box section in a grid pattern at required spacing both ways (vertically & horizontally) or at required spacing near opening, with necessary welding with steel plates at plinth level and roof level and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm (eight millimeter) dia, 75 mm (seventy five millimeter) long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and fixing frame work for partitions wall made of 60x60x3.6 mm (sixty into sixty into three point six millimeter ) column MS square holow box section in a grid pattern at required spacing both ways (vertically & horizontally) or at required spacing near opening, with necessary welding with steel plates at plinth level and roof level and fixing with steel dash fasteners of 8 mm (eight millimeter) dia, 75 mm (seventy five millimeter) long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and fixing in position wall panelling (internal walls) at all heights with 0.48 mm (zero point forty eight) ACP sheet (Aluminium composit panel both as well as one side of the wall) and fixed with self tapping pan head nickel coated mild steel screws of 13 x 3.2 mm (thriteen into three point two millimeter) on to the horizontal and vertical member. The joints between the panels are to be duly joined and finished using recommended jointing for panelling as per manufacturers specification as per direction of Engineer-in-Charge all complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (zero point fifty millimeter) (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size 5.5x 55 mm (five point five into fifty five millimeter) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

Providing 50mm (fifty millimeter) thick glass wool layer coverd with corrugated precoated MS 0.48 mm (zero point forty eight millimeter) thick ACP aluminium sheet from both side (corrugated and ACP sheet shall be measured seprately). Internal wall as per manufacturers specification as per direction of Engineer-in- charge all complete.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimeter) beleved edgf mirror of superior glass (of approved quality) complete with 6 mm (six milli meter) thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete. as per manufacturers specification as per direction of Engineer-in- charge all complete.

Providing and fixing 600x120x5mm (six hundred into one hundred twenty into five millimeter) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm (forty milli meter) long screws, rawl plugs etc., complete as per manufacturers specification as per direction of Engineer-in- charge all complete.

Providing and fixing toilet paper holder :C.P. brass

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour, 600 mm (six hundred millimeter) long towel rail with total length of 645 mm (six hundred forty five millimeter), width 78 mm (seventy eight millimeter) and effective height of 88 mm (eighty eight millimeter), weighing not less than 190 gms (one hundred nintey grames), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & , Concealed work, including cutting chases and making good the wall etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

1216 (16 mm (sixteen milimeter OD) pipe

1620 (20 mm( twenty milimeter OD) pipe

2532 (32 mm (thirty two milimeter OD) pipe

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15 mm (fifteen millimeter) dia nominal bore

20mm (twenty millimeter) dia nominal bore

32mm (thirty two millimeter)dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm (twenty five to forty millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

25 mm (twenty five milimeter) nominal bore

32 mm (thirty two milimeter) nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm (fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm (thirty centimeter) length, 15 mm (fifteen millimeter) nominal bore, for wash basin including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.:

15 mm (fifteen milimeter) nominal bore

20 mm (twenty milimeter) nominal bore

32 mm (thirty two milimeter) nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. In all floors including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT pillar cock of approved quality and colour.15 mm (fifteen millimeter)nominal bore, 107 mm (one hundred seven millimeter)long,weighing not less than 110 gms including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimeter), breadth 102mm (one hundred two millimeter), height of 75mm (seventy five millimeter with concealed fitting arrangements, weighing not less than 106 gms including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

ROSHAN LAL