Constn of Zonal Store at Galsi 2nd call

Cleaning compound premises of shrubs,plants,jungles etc by cutting and removing as directed(specific permission of Engineer-in-Charge prior to execution will be necessary)(payment to be made on area cleared)

Earth work n in excavation of foundation trenches of drain or septic tank, soak well etc. in all sorts of soil including removing, spreading or stacking the spoils within a lead of 75 mtr. or as directed and including trimming the sides of trenches, leveling, dressing and ramming the bottom bailing or pumping out water etc. as required complete.a) Depth of excavation not exceeding 1500mm.

b) Depth of excavation for additional depth beyond 1500 mm, and upto 3000mm. But not requiring shoring.

a)Filling in foundation or plinth by fine sand in layer not exceeding 15 cm. as directed and consolidating same by through saturation with water and ramming complete, including the cost of supply of sand. Do by fine sand

b)Earth work in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm including watering and ramming etc layer by layer complete (Payment to be made on the basis of measurement of finished quantity of work) i)With earth obtained from exavation of foundation.

(i) With carried earth arranged by the contractor within a radius exceeding 3 km. but not exceeding 5 km. including the cost of carried earth.

(ii)With carried earth arranged by the contractor within a radius exceeding 5 km. but not exceeding 10 km. including cost of carried earth

Single brick flat soling or picked jhama bricks including ramming and dressing bed to proper leveling and filling joint with power earth or local sand including cost of sand or earth.

Anti – termite treatment to bottom surface (in case of masonry foundation and basement) and the sides (upto height of 300mm from bottom) of the excavation trenches with chemical emulision by admixing chloropyrofos emulsiflable concentrates (1% concentration) with water by weight at the rate of 5 litres per Sqm area . the work shall be carried out as per specification described in 6.2.1 of code IS-6313 (part-ii) 1981 (mode of measurement will be the plan area of foundation treated)

Anti – termite treatment to the top surface of the consolidated earth within plinth walls with chemical cmulsion by admixing chloropyfos emulsifiable concentrate (1% concentrate) with water by weight at the rate of 5 litres per Sqm of the surface before sand bed or sub- grade is laid. holes upto 50 mm to 75 mm deep at 150 mm centre to centre both ways shall be made with 12 mm di mild steel rod on the surface to facilitate saturation of the soil carried out as per specification described in para 6.4 of code IS-6313(part-ii) 1981. ( mode of measurement will be per Sq.m. of plan area of plinth treated)

Anti – termite treatment to the back filling of R.C.C. foundation with chemical emulsion by admixing chloropyfos emulsifiable concentrate (1% concentrate) with water by weight at the rate of7.5 lit per sq.m of the vertical surface of the substructure of earth side of the foundation. the work shall be carried out as per specification as described in para 6.3.1 of code IS-6313 (part-ii.. as per specification as described in para 6.3.1 of code I.S. 6313 (part –II) 1981.(mode of measurement will be per sq.m. of vertical area of foundation treated)

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.

Cement concrete with graded stone ballast (40mm. size) cxcluding shuttering.(1:3:6 proportion) Pakur variety

(a)Ordinary cement concrete (mix 1:1:5:3) with graded stone chips (20 mm. nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes, Pakur variety.

Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm. nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes Pakur variety

25mm. thick damp proof course with cement concrete with stone chips (1:1:5:3) [with graded stone aggregate 10mm. nominal size] and admixture of water proofing compound as per manufacturer’s specification ..as directed(cost of water prppfing compound & polymer based paint to be paid separately.)

Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

b) In superstructure Gr. Floor

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

125mm. thick Flyash brick work asper IS12894:2002 in cement mortar (1:4) in ground floor.

125 mm Thick brick work with 1st class bricks in cement mortar (1:4) in ground floor using approved H.B. netting in every third layer.

75 mm Thick brick work with 1st class bricks in cement mortar (1:4) in ground floor using approved H.B. netting in every alternate layer.

Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). (When the height of a particular floor is more than 4 m. the equivalent floor ht. shall be taken as 4 m. and extra for works beyond the initial 4 m. ht. shall be allowed under 12(e) for every 4 m. or part thereof.) (Mode of measurement : Area in plan X mean height of staging upto soffit of shuttering above initial 4 m.) a) 25mm. to 30mm. thick wooden shuttering.

c) 25mm. to 30mm. shuttering without staging in foundation.

d) Steel shuttering or 9 mm to 30 mm thick approved quality plyboard shuttering in any concrete. Ground floor

Reinforcement for reinforced concrete in all sorts of structures work including distribution bars. Stirrups binders etc. initial straightening and removal of loose rust cutting to requisite length, hooking & bending to correct shape, placing in proper position and binding with 1.6 gauge black annealed wire at every intersection, complete as per drawing and direction.Tor steel / Mild steel. SAIL/ TATA/RINL a)For works in foundation, basement and upto roof of ground floor up to 4 m.

Labour for chipping of concrete surface before taking up plastering work.

Plaster ( to wall, floor, ceiling etc.) with sans and cement mortar including rounding off or chamfering corners as directed and racking out joints including throating, nosing and drip course, scaffolding/ staging where necessary. i) With 1:6 cement mortar : a) 15mm. thick ( Gr. Floor)

c) 20mm. thick ( Gr. Floor)

ii) With 1:4 cement mortar : a) 10mm. thick ( Gr. Floor) for ceiling bottom of chujja, beam etc.

Neat cement punning about 1.5 mm. in wall dado window sills drain etc.

Bailing or pumping out water from foundation trenches.

Artificial stone in floor, dado, straicase etc. with cement concrete (1:2:4) with stone chips laid in panel as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m. All complete including all materials and labour in ground floor. 3mm. thick topping using grey cement. 35 mm

Wood work in door and window frame in fitted and fixed in position complete including a protective coat of painting at contact surface of the frame excluding cost of concrete, iron butt hings and M.S. clams sal (siliguri)

Supplying solid flush type doors of commercial quality the timber frame consisting of top and bottom rails and side style of well seasoned timber 6.5 cm wide each and the entire frame fitted with 37.5 mm. wide battens places both ways in order to make the door of soild core, internal lapping gurjan or similar wood veneers using phenol formaldehyde as gluee etc. complete including fitting and fixing the shutter in position but excluding the cost of hinges and other fittings in groung floor. 32 mm thick shutters ( single leaf)

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm. (b Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

M.S. or W.I. ornamental grill of approved design, joint continuously welded with M.S W.I flat sand bars for windows railing etc. fitted and fixed with necessary screws and hugs in ground floor. Grill weighing above 10kg/m2 and upto 16kg/m2

Collapsible gate with 40 x 40 mm. 6 mm. Tee as top and bottom guided rail 20 x 10 x 2 mm. vertical channels 100 mm. apart in fully stretched position 20x5 mm. M.S. flat as collapsible bracings properly riveted and washered including 38 mm. steel rollers including locking arrangement, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes chasing etc. in walls, floor etc. and making good damages complete in groung floor (Payment will be made on the area of the gate covered by two guard rails and two extreme channels)

Supplying, fitting and fixing steel window and ventilators with or without integrated grills conforming to IS 1038-1975 as per drawing and manufactured from rolled steel section conforming to Is 7452-1974 with non-friction projecting type, box type hinges glazing blips, lung locking brackt, handle plate etc. including hoisting in position, straightering reguired, fixing lugs in cement concrete (1:2:4) with stone chips 20 mm. down cutting holes and mending good damages to match with existing surface complete in all respect excluding glaxing in ground floor, flash butt welded windows and ventilators. a) Without integrated grill. i) Fixed type steel window as per I.S sizes with horizontal glazing bars.

ii)Open-able steel windows as per I.S.sizes with side hung shutters.

iii) Two point nose steel handle including fitting and fixing.

v) Centre hung ventilator as per I.S. sizes 58 cm.

(a) Supplying, fitting and fixing steel rolling shutter profile type with 18 B.G . of approved type steel latche section 75mm wide, fitted with coil wire spring to necessiate the fitting of required Nos. of C.I. Pulleys on heavy type solid drawn seamless steel tube complete with locking arrangements both inside and outside specially builtup side guide channels including providing a hood for the steel rolling shutter in the room, painting two coats of approved aluminium paint over a coat of red lead primer complete.

Supplying, fitting & fixing M.S. clamps for door and window frame made of flat bifurcated with necessary screws etc. by cement concrete(4:2:1) as per direction. 40mm. x 6 mm. 250 mm. length.

Oxidised iron butt hinges of approved quality fitted and fixed with steel screw with ISI mark. 100 x 58 x 1.90 mm. (Oxidised)

M.S. gat

e of Jail type as per approved design made of strong M.S. frame work, intermediate stiffeners and round / square bars or angles. M.S. sheet (not less than 14 gauge) gussets, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the Engineer-in -charge. Including fitting, fixing bottom roller in position.

c) Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. ( in all floors for internal wall & upto 6 m height for external wall). 3 mm thick (weighing 7.4 Kg/ Sqm)

Supplying, fitting and fixing Godrej mortice lock chromium plated with latch and keys 4 levers, including fitting and fixing complete

Supplying, fitting and fixing in position approved PVC door frame made of extruded PVC multichamber hallow section having dimensions 60mm. x 50 mm. x 2 mm.(+0.2mm.), horizontal section by galvanized steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm. x 20mm. x 1.2mm. will be inserted on one full vertical side of the frame as reinforcement the frame will then be fixed in the opering with the help of PVC expandable fastener wooden gutties and galvanished steel screws including cost of all materials and labour hire charges of all materials, taxes and all other incidental charges complete.

Supplying, fitting and fixing P.V.C door shutter of approved quality and shade in position, the style & rail of the PVC door shutter will be made of rigid PVC multicavity hollow chamber of 50mm. x 30mm. section with 2.0 mm.(+0.2mm.) wall thickness horizontal & vertical section shall be fixed to each other by self tapping screws and one solid ..tools and plants and appliances carriage of all materials, taxes and all other incidental charges complete. The rate is exclusive of cost of hinges, hasp bolt, tower bolt, door ring etc.P.V.C door shutter 30mm. thick :

a) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality, including smoothening surface by sand papering etc.

b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality, including smoothening surface by sand papering etc

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface if necessary. a) On timber or plastered surface with super gloss(hi-gloss) On timber or plastered surface with super gloss(hi-gloss) 2 coats (any shade except white)

b) On steel or other metal surface with super gloss (hi-gloss) 2 coats (with any shade except white)

Cement washing including cleaning and smoothening surface thoroughly external surface one coat.

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-in- charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1956 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. including handling charges of materials for the work complete. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc.and no seperate payment being made for these items, as per direction of Engineer In Charge. For structural members of specified sections weighing less than 22.5 Kg./m

M.S. structural works in roof trusses with tubular sections conforming to IS: 806-1968 & IS: 1161- 1998 cnnected to one another with bracket, gusset cleats as per design, direction of Engineer-in-charge complete including cutting to requisite size, fabrication with necessary metal arc welding conforming to IS: 816- 1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour reqired for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural tubular memebrs as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a height of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof. For trusses spanning up to 12.00 m

Supplying, fitting and fixing UPVC pipes A-type and fittings conforming to IS : 13592-1992 with all necessary clamps, nails, including making holes in wall, floor etc. cutting trenches in any soil, thorough masonry concrete structure etc. . UPVC pipes. i) 110 mm. dia

ii) Shoe - 110 mm. dia

iii) Tee - 110 mm dia

Plain Y(a) 110 mm dia

Bend 87.5 degree (a) 110mm dia

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992.(i) Single Socketed 3 Meter Length.110mm dia

Double socked 3meter.length.110mm

Door Tee (LH) & (RH),110mm dia

Door Y (LH) & (RH),110mm dia

Double Y with door 110mm dia

Door Bend (LH) & (RH).110mm dia

Passover .110mm dia

Cross Tee with door.110mm dia

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be madeon area of finished work) ,In roof a) With 0.5 mm thick sheet

Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping).(B) 450 mm lapping each way. (b) With 0.63 mm sheet

Providing and fixing at or near ground level precast cement concrete in kerbs (size: 410 mm x 310 mm x width 150 mm at bottom with circular nosing at top) (Nano kerb) of cement concreat M25 Grade without reinforcement, fixing as per approved pattern and setting in position at site after preparing the bed grade and slopes by laying Cement concrete with jhama khoa (1:4:8) as per specification and direction of Engineer-inCharge including filling of joints with 10 mm thick cement morter (3:1) and back filling the vertical piece properly with earth duly compacted and curing the morter joints for atleast 3 days including cost and carriage of all materials complete

Supplying and laying true to line and level High Grip, Scratch resistant, Neutral to UV rays, Full Body Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and tested in accordance with IS:13630 [No

n- modular sizes for tiles with Skid resistance: 0.6, Mohr's hardness > 7.0, Staining resistance: Class1, Water Absorption E < 0.5%] & MOR > 35N/sq.mm and Breaking strength > 1500 N for Outdoor area of building e. g. Gang-way, Corridor, Driveway, Parking lots, Courtyards, Sloping ramps, Entrance lobbies, Patios, Portico etc. set over necessary underlay and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles and removal of wax coating of top surface of tiles with warm water and cleaning the tiles using soft and dry cloth complete including the cost of materials, labour and all other incidental charges complete including backside slurry but excluding the cost of underlay and true to the manufacturer's specification and direction of Engineer-inCharge. In Ground Floor: Sizes-300 mm x 300 mm x10 mm

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A)Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. Area of each tile above 0.09 Sq.m Coloured decorative. Ground floor

(B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m Area of each tile above 0.09 Sq.m Coloured decorative

18 mm. thick marble partition slab with chawk doongri marble square cut, both side polished with two front corners rounded and edges polished fitted and fixed complete.

18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in -charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0 kg/Sq.m]

Supplying, fitting & fixing granite slabs 15mm to 18 mm. thick with uniform texture & without decorative veins in columns, wall, facia,rise etc. with 15 mm thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of all materials, labours, scaffolding, staging, curing and roughening of concrete surface complete. [Using cement slurry at back side of granite @ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m] In ground floor (a) Area of each Granite slab above 1.00 Square meter

Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mm thickness in floor, lobby, stair, landing & treads etc. over 20 mm (av.) thck base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in -Charge in Ground Floor. {White cement and Pigment to be supplied by the Agency](iii) Area of each Slab/tile exceeding 0.60 sq.m but not exceeding 1.00 sq.m.

Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid U-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 15mm thick OW Acoustic Board (Mineral Fiber Acoustic Ceiling Tiles) of approved patern and size 595mm X 595mm with NRC value > 0.65 should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge. In ground floor.a) Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U1520).

M.F. suspended ceiling made with 12.5 mm thick Gypsum plaster board including G.I. perimeter channel of 0.55 mm flush (having two flanges 20 mm and 30 mm respectively and web 27 mm ) along with perimeter of ceiling with G.I. intermediate channel of 0.9 mm thick size 45 mmx15mm placed at 750 mm c/c with G.I. ceiling angle of size 25 mmx10mmx0.55 mm thick fixed to the ceiling with G.I. Cleat and steel expansion fastener ceiling section 0.55 mm thick of size 51.50 mmx26mm fixed to the intermediate channels with the help of connecting clip and in the direction of perpendicular to the intermediate channel of 300 mm c/c 12.5 mm thick Gypsum plastered board are to be fixed under ceiling section as above by machine screws. The boards are to be joined and finished with jointing compound, paper tape and application of top coat etc. as per the direction of Engineer-in-charge. (The rate includes of cost of all materials including taxes, cost of accessories, fittings and fixtures, scaffolding and labour charges etc. complete) In ground floor

Supplying, fitting and fixing flat back urinal in white vitreous china ware of approved make in position with brass screws on 75 x 75 x 75 mm. wooden blocks complete. 470 x 280 x 340 mm.

Supplying, fitting and fixing orrissa pattern – water closet in white glazed vitreous china ware of approved make in position complete excluding ‘D’ or ‘S’ trap 530 x 410 mm.

Supplying, fitting and fixing 10 liter PVC low down cistern conforming to I.S. specification with PVC fittings complete C.I. brackets including two coats of painting to bracket etc.

Supplying, fitting and fixing approved brand 32 mm. dia PVC waste pipe, with PVC coupling at one end fitted with necessary clamps.750 mm. long.

Supplying, fitting and fixing approved brand PVC connector white flexible with both end coupling with heavy brass CP nut 15 mm. Dia . 450 mm. long.

Supplying, fitting and fixing white china best quality of approved make wash basin with C.I. brackets on 75 x 75 mm wooden blocks C.P.waste fittings of 32 mm. dia one of approved quality brass C.P. pillar cock of 15mm. ………..including mending good all damages and painting the brackets with two coats of approved paints. 550 x 400 mm. size.

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm. thick with silvering approved quality as per I.S.I. specification supported on fiber glass freme of any colour frame size 600 x 450 mm. complete in all respect as per direction of enginee

r-in-charge.

Supplying, fitting and fixing porcelin soap tray of approved make. (i) Recessed soap tray of size 150 mm. X 150 mm.

Supplying, fitting and fixing allumium approved brand towel rail 25 mm. dia 450 mm. long with two brackets complete all respect as per direction of engineer-in-charge.

a) Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S. 3989 /1970 and I.S. 1729/1964 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. (Measurement will be made along the center line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately).With valamoid joints including sealing with sand cement mortar (4:1) upto quarter depth 100 mm. (internal)

Supplying, fitting and fixing C.I. approved patent vent cowl confirming to ISS 1729 of 1970 supplied fitted and fixed in position cpmplete with load caulked jointing.100 mm. dia.

Supplying, fitting and fixing cast iron ‘P’ or ‘S’ trap conforming to IS 3989/1970 and 1729/1964 including lead caulked joints sand painting two coats to the exposed surface. 100 mm. ‘P’ trap.

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials.For 10 users A) With Pakur variety.TATA/SAIL/RINL

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia.

Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling,15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. i) With Pakur variety.

Supplying, fitting and fixing C.P. stop / bib cock.i)Chromium plated bib cock short body.

ii) Chromium plated stop cock

Supplying, fitting and fixing pillar cock of approved make. a) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing approved quality PVC. water storage tank with closed up with lid ( Black) Multilayer top cover 1000 liter capacity.

Labour for hoisting plastic water storage tank (i) upto 1500 Lt capacity

Supplying, fitting and fixing peets valve full way gun metal standard pattern best quality of approved brand with fittings. i) 25 mm.

Supplying, fitting and fixing shower of approved brand and make.Chromium plated round shower with revolving joint.

Supplying, fitting and fixing stainless steel sink complete with waste fittings on C.I. brackets including two coats painting of brackets sink only 540 x 430 x 180 mm.

Supplying, fitting and fixing fan hook for ceiling with 1mtr. Long 16mm. dia. For complete including mending damages.

Supplying, fitting and fixing 100 mm. C.I. round gratings (heavy type)

Supplying, fitting and fixing pedestal of approved make for wash basin (white)

Supplying, profiles of required section made of aluminum alloy extrusive confirming to I.S. 732-1983 and I.S. 1285-1975 anodised film thickness and specification colour/natural) matt finished confirming I.S. 1868-1983 for fabrication of composite door, sliding & casement windows, partitios, formed of basic sections of any ISI embossed/certified make and brand as per direction of Engineer-in -charge (payment will be made on finished length of the work). A) In 10-12 micron thickness Anodizing a) Movable door i) Door frame (top & sides)

ii) Shutter top rail

iii) Shutter bottom rail

iv) Shutter lock rail

v) Door vertical

vi) Glazing clip

v) Door vertical

Supplying, profiles of required section made of aluminum alloy extrusive confirming to I.S. 732-1983 and I.S. 1285-1975 anodised film thickness and specification colour/natural) matt finished confirming I.S. 1868-1983 for fabrication of composite door, sliding & casement windows, partitios, formed of basic sections of any ISI embossed/certified make and brand as per direction of Engineer-in -charge (payment will be made on finished length of the work). A) 15 micron colour Anodizing (i) a) 2- track sliding window i) Bottom frame .

ii) Top and side frame.

b) 3- track sliding window i) Bottom frame

c) Shutter for all track sliding window.

i) Bottom & Top member.

c) Shutter for all track sliding window. ii) Style side member.

c) Shutter for all track sliding window. iii) Interlock member.

Supplying PVC rollers for sliding windows as per direction of Engineer in charge.

Supplying maruti lock (100mm)

Supplying, profiles of required section made of aluminum alloy extrusive confirming to I.S. 732-1983 and I.S. 1285-1975 anodised film thickness and specification colour/natural) matt finished confirming I.S. 1868-1983 for fabrication of composite door, sliding & casement windows, partitios, formed of basic sections of any ISI embossed/certified make and brand as per direction of Engineer-in -charge (payment will be made on finished length of the work). A) In 10-12 micron thickness Anodizing ilm . a) Fixed Partition (Unsupported length of vertical member upto 1.5 mtr. Height of both ends of vertical member restrained but panels within 0.9 sq.m.) i) Top , bottom & side member.

ii) Intermediate member.

Wall panelling / partition with Melamine faced 3 layered flat pressed wood particle board of approved make and brand as per direction of Engineer - in - Charge of requisite grade bonded with phenol formaldehyde synthetic resin conforming to IS: 848 - 1974 (excluding the cost of supporting frame work andteak wood battens / lipping)In Ground Floor(B) Prelaminated particle board conforming to IS: 3087 - 1985 and IS 12823 -1990 (ii) Both side decorative laminate (a) Exterior grade12mm thick

Supplying, fitting and fixing anodized aluminum barrel / tower / socket bolt 225 mm. long & 10 mm. dia bolt of approved quality make from extruded section with conforming to I.S. 204/74 fitted and fixed with cadmium plated screws 225 mm. long & 10 mm. dia bolt.

Supplying, fitting and fixing anodized aluminum aldrop / sliding bolt of approved quality manufactured from extruded section confirming to I.S. specification (I.S. 2681/66) complete .250 mm. long by 16 dia bolt.

Door stopper (Brass)

iv) Aluminium peg stay 300 mm. long including fitting and fixing.

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987 5mm thick clear glass.

Supplying ‘U’ shaped EPDM gasket of approved make and brand and brand as per direction of EIC.

weather gasket / wool pile for door vertical

Labour charges for fabrication and installation of composite door window, partition made from anodized extended alloy aluminum sections. For the following units:- Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge.

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units (A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers. i ) 2 track sliding window.

ii ) 3 /4 track sliding window.

Fixed glazing

Applying exterior grade acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured ( matt finish ) or smooth finish acrylic exterior emulsion paint including scraping and preparation the surface thoroughly complete as per manufacturer`s specification and as per direction of the EIC. G.Fl.

Protective and decorative acrylic exterior emulsion paint of approved quality as per manufacturer`s specification and as per direction of EIC to be applied over acrylic primer as required. the rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer (G.Fl 2 coats) normal acrylic emulsionprimer 100% acrylic exterior emulsion paint of approved quality as per manufacturer’s specification. i)In ground floor

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick).

Applying interior grade acrylic primer of approved quality and surface old or new surface to receive distemper / acrylic emulsion paint including scraping and preparing the surface thoroughly. Water based interior grade acrylic primer.

Applying acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (two coats) Luxury quality

Supplying& laying 20 mm designer chequered tiles of any shade and of approved quality as per IS: 1237: 1980 laid in patterns as directed in pavement, footpath including necessary underlay 25 mm thick average cement mortar (1:3) complete in all respect with all labour and materials [using cement slurry @ 4.4 kg/Sq.m at back side of tiles. Cement of mortar & slurry will be supplied by the Department. Border concrete if necessary to be paid separately].

Supplying, fitting and fixing Stainless Steel railing consist of 38mm dia and 900mm height vertical balustrade at every two alternative steps, 50mm dia top rail, 3 (three )nos 19mm dia horizontal Strainless steel pipe and base/cover plate with Strainless Steel GRADE 304 containing 7.5% nickle (Interior Grade)Brushed/Mat finish, complete as per direction of the Engineer-incharge. Weight of Strainless Steel railing per metre 6.5 Kg(approx)

Supplying, fitting and fixing cast iron heavy type spiral staircase of approved design with 50 mm.dia. Stem and C.I. Steps 150 mm as per design 900 mm. high C.I, railing including necessary M.S. tie of suitable section embedded to wall with cement concrete (1:2:4) including cost of intermediate C.I. platform secured with necessary tie to stem and wall with cement concrete (1:2:4) including fixing the stem in ground with cement concrete (1:3:6) complete in all respect with all labour and materials. (Payment to be made on vertical height in between 1st step and top platform.) (a) With 1200 mm.dia. wel

Supplying fitting and fixing 600 mm ( ±30 mm) diametre R.B.T (Reinforced Barbed Tape) Concertina fencing on wall top using concertina coils stretched to approx.6 meters length at site clipped with two nos. of horizontal R.B.T strands which will be tensioned and fixed with the vertical M.S angle iron posts by means of security fasteners (such as 'C' clips, R.B.T clips etc.)

Supplying & laying interlocking 60mm thick designer paver block(M-35) of anyshade and of approved quality as per IS: 1237-1980 laid in pattern as directed in pavement, footpath, driveway, etc including necessary underlay complete in all respect with all labour and material.[Border concrete if necessary to be paid separately]. (b)40 mm thick block (over 150 mm medium sand bed including cost of sand but excluding cost of earthwork in excavation or dismantling of existing hard surface if necessary) (ii) Coloured Decorative

Supplying galvanised straining bolts (with eye at one end with double nuts and washers) fitted and fixed complete. 12 mm. dia. 250mm long

Supplying galvanised staples fitted and fixed complete. 44 mm. to 50 mm. size

Supplying, fitting galvanised 3 ply 12 gauge / 4 points line of barbed wire in fencing (holes already made in the body of the post) or fixed by staples tightening and fixing the wires in taut condition with straining bolts including the cost of cutting and of lapping joints in the wire as necessary but excluding the cost of galvanised staples,straining bolt and binding wire where necessary.

Supplying & laying interlocking 60mm thick designer paver block(M-35) of anyshade and of approved quality as per IS: 1237-1980 laid in pattern as directed in pavement, footpath, driveway, etc including necessary underlay complete in all respect with all labour and material.[Border concrete if necessary to be paid separately]. (b)40 mm thick block (over 150 mm medium sand bed including cost of sand but excluding cost of earthwork in excavation or dismantling of existing hard surface if necessary) (ii) Coloured Decorative

Supplying galvanised straining bolts (with eye at one end with double nuts and washers) fitted and fixed complete. 12 mm. dia. 250mm long

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (a) For Exposed Work CPVC Pipes Class-1, SDR-11 1. 15 mm dia.

2. 20 mm dia.

3. 25 mm dia.

4. 40 mm dia.

(b) For Concealed Work CPVC Pipes Class-1, SDR-11 1. 15 mm dia.

Labour for boring tube well of required dia.by water jet system through any type of soil strata including hire and labour charges for boring pipes,scaffolding,tools and plants as necessary and taking out them and lowering pipes,strainers,blind pipe etc.and other fitting and fixing the same complete including bucket washing and other incidental works in the connection.The tube well should have mininum 50 mm gap in between the outside of the tube well pipe and the bore.For depth upto 150 meter for 80 mm dia.Tube well with top enlargement of 150 mm dia.80 mm dia.boring etc.

150 mm dia.boring etc.top enlargement

Supplying high density polythene strainer of approved make with adopter conforming to I.S.Specification .(i) 80 mm dia.

Supplying, fitting and fixing of steel cutter piece up to 450 mm long with sockets .75 mm dia.

Supplying, fitting and fixing plug of approved make conforming to I.S. specifications.75mm dia

Washing and development tube well with air compressor pump and engine for 8 (eight) hours continuos pumping per day with necessary arrangement for testing the yield in gallons per hour with 'V' notch including hire and labour charges for all tools and plants and scaffolding as required.

Packing the annular space between the outside of the tube well pipes & strainers and the bore with pea size washed gravel of approved quality having size from 2 mm to 5 mm or the size approved by the Engineer-in-charge including cost of all materials labour and equipment complete.

Packing the annular space between the outside of the housing pipes and the bore with puddleballs of approved by the direction of the Engineer-in-charge including cost of all materials and labour complete.

Supplying , fitting and fixing of heavy type bell mouth reducing socket 75 mm X 150 mm .

Supplying, fitting, fixing G.I. Cap at top. 150 mm

Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). (a)80 mm

Collecting sample of water for bacteriological and chemical test for any depth at any time during execution of work including hire and labour charges for tools and plants and sterilization of equipments paying all charges and fees of testing, etc. complete in all respect as per direction.

Supplying , fitting, fixing in position Submersible pump 1.5 H.P. of K.S.B. make,stage 18, 220 volt submersible motor pump model No.KSB CORA 75 37C (Single phase)