REPAIRS TO JOINERY, ROOF TREATMENT, SUNKEN TREATMENT AND SANITARY FITTINGS AND OTHER ALLIED WORKS IN TECH AREA UNDER GE (AIRFORCE) LOHEGAON AT AIRFORCE STATION PUNE

Amount

Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n'exc 1.5 Sqm each complete all as directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each complete all as directed by Engr-in-charge.

Taking down shutters of any description area not exceeding 1 Sqm each complete all as directed by Engr-in-charge.

Hacking old broken glass (any thickness, size, quality or description) from aluminium/steel/wooden frame work or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and as directed .

Taking down shutters of any description area not exceeding 1 Sqm each easing & adjusting and refixing in the same opening complete all as directed by Engr-in-charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each easing & adjusting and refixing in the same opening complete all as directed by Engr-in-charge.

Removal and Fixing in repairs of existing Rolling shutters after replacement of dammaged laths/ panels ,easing, greesing and refixing in the same opening all as specified and directed by Engr-n charge. Note: Replaced laths/panels ,hoods etc shall be measured and paid seperatly as per Items below.

S&F in repairs of Steel rolling shutters with thicknes of each laths of 1mm thick,with out ball bearing ,as specified,including top cover anchoring rod ,hasp and staple and one shop coat of primer;erected in position as indicated,complete:push pull or manual type incuding removal of old dammaged rolling shutters all as specified and as directed ,cost for removal of old Rolling shutter for repais will be paid seperatly as per Item no 02 above.

Removal and Fixing in repairs of existing Gear operated Rolling shutters , replacement of dammaged laths/ panels ,easing, greesing and refixing in the same opening all as specified and directed by Engr-n charge. Note: Replaced laths/panels, safety lever locks, bearings etc should be measured and paid seperatly as per Items below.

S&F Steel rolling shutters with thicknes of each laths of 1mm thick,with out ball bearing ,as specified including top cover,anchoring rod ,hasp and staple and one shop coat of primer;erected in position as indicated,complete:gear operated type with bevel gear box and crank handle type incuding removal of old dammaged rolling shutters all as specified and as directed.cost for removal of old Rolling shutter for repair will be paid seperatly as per Item no 02 above.

S&F in repairs for Mild steel ,plain black sheet of minimum 0.8mm thickness for Hoods cover for Rolling shutters; covering to door shutters; water tank platforms etc with plain 40mm lap joints or welded/riveted seams including ,bending, turning up, mitred angles , stopped ends,outlets,etc. as required all as sprcified and directed by Engr-in Charge.

S&F in repairs Safety lever locks mild steel with 4 levers for rolling shutters.

S&F in repairs Ball bearing for rolling shutters.

S&F of Collapsible steel gates side hung, considering of channel pickets , pivoted flat bars, top and bottom runners,handles etc, as specified,erected in position and securing runners with hold fasts and brackets, complete all as specified and directed by Engr-in- Charge incuding removal of old dammaged collapsible gates complete all as specified and as directed.

M&L Anodised aluminium frame of standerd section for doors, windows, ventilators and partitions with double rebates including joining cleat for fixing etc. complete all as specified

M&L for powder coating in Anodised aluminium frame of standerd section for doors, windows, ventilators and partitions with etc as per item no 26 above. complete all as specified.Note: Over all weight of Anodised aluminium frame shall be considered for payment .

M&Lfor Anodised aluminium door shutters, aluminium sections weeighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws,hinge type B-21 100mm long (3 no.) suitable handle (2 no.) (Glass / Wiremesh should be measured and paid seperately) complete all as specified

M&L for anodised aluminium window and ventilator shutters of any type with or without sash bars, aluminium sections weeighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fitings such as suitable stays ,suitable hinges (if required.) suitable handles (1 no.) (Glass / Wiremesh should be measured and paid seperately)complete all as specified

M&L for powder coating in Anodised aluminium frames of shutters of Doors ,window and ventilator openings etc as per items 18 & 19 above. complete all as specified. Note: Over all area of shutters of Doors ,window and ventilator shall be considered for payment.

M&L sheet glass 4.8mm thick ordinalry quality and glazing with aluminium beeds in square exc 0.50 sqm in each pane complete all as specified and as directed

M&L 9mm thick Prelaminated particle board ,exterior grade having decoratie choice lamination on both sides fixed with aluminium beadings on aluminium frame work all as specified and directed.

S&F Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixings lugs,excluding hinges,lock strike plate,etc,complete ,as specified ,supplied and fixed.

S&F Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixings lugs,excluding hinges,lock strike plate,etc,complete ,as specified ,supplied and fixed.

S&F 2nd class hard wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete(Glass shall be measured Seperately) all as directed by Engr-in-Charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Chage

M&L for treating wooden chowkats surface of any description n exc 10 cm in width or girth with black bituminus paint in two coats.

M&L for preparing and treating small articles of builders hardware such as MS hold fasts ,MS but hinges etc, with two coats of synthetic enamal paint over a coat of primer when un-connected with other paintings or when painted in a different tint.

M&L for PCC (1:3:6) type B0 (using 12.5 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and as directed by the Engr-in-Charge.

S&F for 30mm thick 2nd class hard wood plain framed paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats , complete all as directed by Engr-in-charge.

S&F for 30 mm thick Flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides , Supply and fixed to chowkats , complete all as directed by Engr-in-charge.

S&F 30 mm 2nd class hard wood Glazed and skelton door or window shutter, open and prapared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and as directed by the Engr-in-Charge..

S&F MS framed work such as grills, gratings etc with ends of bars shouldered and/or rivited or forged in spikes, framed guard bars, barred iron doors, ledders framed balsters walk ways railings frame work of water tanks and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F Steel windows (frame with shutter) with side hung shutters including box type hinges with steel handle ,and steel peg stay,complete with glazing bars,dovatiled or welded (Glass shall be measured Seperately)complete all as specified and directed by Engineer-in-Charge.

M&L sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.

S&F in repairs Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and as directed by Engineer-in-Charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed by Engineer-in-Charge.

S&F mild steel butt hinges, medium weight cold rolled 75mm size complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F in repairs mild steel ordinary rat tail rod pattern springs of size upto 300mm long including roller and roller plate complete all as specified and as directed.

S&F in repairs Aluminium alloy anodised ,sliding door bolt 250mm with hasp,staple(bolt type) and fixing clips of sheet ,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast, aluminium alloy complete all as specified and as directed.

S&F in repairs Aluminium (extruded section) door closer hydraulically regulated ,designation No.3, universal type, suitable for door shutter of 851 to 1000mm in width and of weighjt between 61 to 80 Kg all as specified and as directed.

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box ,main body with stainless steel cover,governing pivot made of brass, other plates made of mild steel heavy duty.

S&F in repairs 100mm Aluminium Mortice lock 2 levers vertical type complete all as specified and as directed.

Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and as directed

M&L Anodised aluminium snap grid frame work for false ceiling of grid size 605 x 605 mm including necessary hanger wires as per manufacturers specification complete all as specified

S&F Gypsum Board 600 x 600x10mm thick in ceiling fixed with screw as per manufacturers instructions

M&L Insulated PVC Wall & Ceiling Lining of 12.5mm thick consisting of PVC Panels Having expanded polystyrene (EPS) stuck to1.0mm thick plain colour PVC sheet duly fitted into the wall & Ceiling as per specifications and drawing

S&F 2.5mm thik PVC sheet fillets of width upto 35mm for wall panelling inclusive of fixing on wall to make PVC frame as per specification and drawing.

M&L for Forming jambs, etc.in Cement mortar 1:6 to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete

M&L for Making good under cills or over arches, lintels and bressummers in Cement mortar 1:6, including all pinning when necessary

Dismantling roof treatment of any description in suspended slabs in roofs,suspended floors, chajjas, landings etc,including cement mortar bedding,padding concrete and rubbish of premises complete all as specified and directed.

M&L for Cutting out cracks to V section in existing roofs or terracing ,cleaning out ,wetting, grouting with cement and sand slurry 1:3

M&L for 10 mm thick rendering on fair faces of brick works / Concrete surfaces finished even and smooth without using extra cement in cement mortar 1: 3complete all as specified and as directed

M&L for PCC type B0 (1:2:4) using 12.5 mm graded crushed stone aggregate in Coping / Coving/padding concrete,mass concrete and the like.

M&L preparation of surfaces and applying two coats of hot bitumen blown 85/25 grage to concrete surface @1.2kg/Sqm complete all as specified and as directed

M&L App based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforment with polyster non woven fabric (wt reinforcement not less than 150 gms/sqm) laid on primed surfaced application and including application of two coats of Aluminium paint over APP Membrane complete all as apecified and directed

Dismantling plain or corrugated steel /fibre/AC sheeting any gauge thickness including nanital or similar pattern complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F MS Wind ties for roof including securing bolts, posts & struts including cutting tops to shapes as directed,including all necessary drilling,bolting or riveting etc and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall ,fixed with self tapping screws and all as specified and as directed.

S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall ,fixe with self tapping screws and all as specified and as directed.

S&F Fibre glass reinforced translucent plain sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and as directed

M&L applying two coats of synthetic enamel painting to new surfaces steel of any description surface over a coat of red oxide primer exc. 10 cm width/girth complete all as specified and directed

M&L for preparation of existing treatment on steel / Roofing sheets of any descripton and applying one coat of camouflage pattern synthetic enamel paint,complete all as specified and as directed.

Taking down cement plaster any description on brick/stone or concrete walls, etc including racking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

Demolition of Brick/precast concrete block/Stone/boulder masonary walling built in cement mortar including all quoins, arches , pillars etc all as specified and as directed

M&L Pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonary exc 10cm in width with solid blocks exc.10cm in width and setting in cement mortar 1:6 complete all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick works finished even andfair without using extra cement in cement mortar 1: 4 complete all as specified and as directed

Supply only Liquid water proofing compound.

M&L for 15 mm thick rendering in CM 1:6 on unfair faces of brick works finished even, fair and smooth without using extra cement complete all as specified and as directed

M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of primer complete all as specified and as directed.

M&L for preparation of new concrete /plastered surface of any description,applying three coats of white wash complete all as specified and as directed complete all as specified and as directed.

M&L for preparation of new concrete /plastered surface of any description, and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed complete all as specified and as directed.

M&L for preparation of new wood or wood based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer as directed complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing ) and rubbish of premises complete all as directed.

Demolition of stone slabs and chequered tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar.

Demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbes, aprons, etc laid dry or laid dry and pointed.

Demolition of cement concrete in ground floor and pavings n'exc 15cm thickness (below or above ground level complete all as specified and as directed).

M & L for 75 mm PCC 1:3:6 type C-2 using 40mm graded stone aggregates as plinth protection finished even and smooth without using extra cement complete all as specified and as directed.

M & L for 75 mm PCC 1:3:6 type C-2 using 40mm graded stone aggregates as in sub floor or hard standing rough finished surface all as specified and directed

M&L Forming Contraction (Dummy) joints 75 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'B' in plinth protection

M&L for vitrified ceramic tiles 10mm thick (light shade ) (square/rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11Sqm and nexc .18 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 and nexc .11 sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for screed bed with M (1:6) 15mm thick for laying floor tiles all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for rendering screed bed with CM (1:4) 10mm thick for laying wall tiles all as specified and directed.

Taking down steel tubing ( 15mm bore) and connections in any position including cleaning for refixing or removal to store complete all as directed by Engr-in-charge.

Taking down steel tubing ( 20mm bore) and connections in any position including cleaning for refixing or removal to store complete all as directed by Engr-in-charge.

S&F GI tubing of 15 mm dia medium grade with all fittings & fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by the Engr-in-C.

S&F GI tubing of 20mm dia medium grade with all fittings & fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by the Engr-in-C.

S&F in repairs 15mm Stope/Gate valve ,cast copper alloy,screwed down, high pressure,with crunch or butterfly handle ,screwed both ends for iron pipe or for union and fixed

S&F in repairs 20mm Stope/Gate valve ,cast copper alloy,screwed down, high pressure,with crunch or butterfly handle ,screwed both ends for iron pipe or for union and fixed

S&F Rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) 500 Ltr capacity hoisted and fixed in position including removal of existing damaged water tanks all as specified in SSR Part I

S&F Rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) 1000 Ltr capacity hoisted and fixed in position including removal of existing damaged water tanks all as specified in SSR Part I

S & F in repairs 20 mm Brass valves ,high pressure,with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed

Disconnecting water tanks of capacity 500 liters ,cleaning and removing all scale and dirt,etc from tanks and from mouths of circulating pipes ,etc and refixing in the same position all as specified in SSR Part I

Disconnecting water tanks of capacity 1000 liters ,cleaning and removing all scale and dirt,etc from tanks and from mouths of circulating pipes ,etc and refixing in the same position all as specified in SSR Part I

S & F in repair Vitreous China wash basin, white, flat back, size 480 x 450mm including cutting for and pinning in ends of brackets or erecting stand but inclusive of fixing of supply and waste pipe.

S&F in repairs Vitreous China bowl Urinal, flat back, size of 465x355x265mm white with grating and union for discharge pipe and PTMT waste coupling with waste pipe (excluding flushing cistern, flush pipe and waste pipe)

S&F in repairs Vitreous china wash down water closet scouting pattern, white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and Mild steel chromium plated hinging device including trap set and necessary concrete complete.

S&F in repairs Vitreous China Sqatting pan Orissa Pattern Indian Type Size 580 x 440 with integral foot rest (excluding flushing cistern and flush pipe). Colour as desided by Engneer-n Charge.

S&F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed.

S & F in repairs 15 mm bore pillar taps, fancy type Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe. Make: Cat pat No- F100001 of Hindware

S&F in repairs Angle stope valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated with long shank and cup (concealed type), 15mm bore dia of pipe. complete all as directed by Engr-in-charge.

Supply only waste pipe of polyethylene of low or high density or PVC ,32 mmdia for urinal/wash basin/ flush tankfixed in repairs. complete all as directed by Engr-in-charge.

S&F in repairs PVC connection pipe suitable for connecting flushing cistern and WHB etc 450mm long complete all as specified and directed.

S & F in repairs, waste coupling of PTMT 32mm bore for urinal / wash basin (Half or full threaded ) (Minimum Weight 45 grams) complete all as specified and directed.

S & F in repairs CP floor gratings 100mm dia with or without waste hole of PTMT (mim waight 40 grms) complete all as specified and directed.

S&F in repairs 15mm dia bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe complete all as specified and directed.

Demolition and breaking up drain pipes ( salt glazedware, AC,Reinforced concrete, PVC pipe) of internal dia upto110 mm bore, set in cement mortar and taking out of trenches if required.

S&F 110 mm dia, PVC rain water pipes, single socketed, in any length with sealant rubber ring joints including necessary MS flat Iron clamps of size (40 x 4mm) all as specified and as directed by the Engineer - in - Charge.

S&F 75 mm dia, PVC rain water pipes, single socketed, in any length with sealant rubber ring joints including necessary MS flat Iron clamps of size (40 x 4mm) all as specified and as directed by the Engineer - in - Charge.

M&L for PCC 1:3:6 type C-2 (40mm gradded stone aggergate) bed to drain pipe including packing under and hanching against side after they are laid and tested up to 110/75mm dia pipe

M&L for Cement concrete type D-2,1:4:8 (40mm graded stone aggreate) 100 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc..

M&L machine pressed precast concrete interlocking paver block any shape and size polished with grey cement and pigment confirming to IS 15658-2006 of 60mm thickiness M-35 grade complete all as specified and as directed by Engr-in-Charge..

M&L sand filling (50 mm average thickness) under floors in foundations and for laying Interlocking paver blocks including watering and consolidation complete all as specified and as directed by Engr-in-Charge..

M&L PCC 1:2:4, 25 mm thick type B0 using 12.5mm graded stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-charge.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick including skirting over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete.

M&L for 20mm thick Chequered cement concrete tiles of standered size as directed by Engr-in-Charge , set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments all as directed by Engr-in - charge.

M&L for screed bed with CM (1:6) 20mm thick for laying floor tiles complete all as specified and directed.

M&L for preparation of old wooden joinery surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

M&L for preparation of old plastered wall surface of any description and applying one coat of Oil bound destemper complete all as specified and as directed.

M&L for preparation of old plastered wall surface of any description and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old plastered wall surface of any description and applying one coat of cement based paint complete all as specified and as directed.

Shri Sant Cosntruction

M/S S H KHAN ENTERPRISES

santulan & Company