PROVISION OF CERTAIN SPECIAL REPAIR AND REVENUE WORKS AT B B CANTT, SRINAGAR

Amount

Dismantling plain or corrugated steel sheeting, any gauge thickness including nainital or similar pattern roof coverings complete all as specified and directed

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in wall, fixed with self tapping screws complete all as specified and directed

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridge/Eaves Board complete all as specified and directed

Fixing only Galvanised, corrugated mild steel sheeting with two corrugation side lap fixed with coatch screws and washers in roofs, 0.63 mm thick m Gde-o quality, with 120 grms/sqm zinc coating and Gde 'B' (i.e 12.5 mm ) corrugation, complete all as specified and directed

Dismantling wooden boarding, any description , fixed in any position with nails complete all as specified and directed

S&F 2nd class softwood 20mm thick boarding clean sawn/eaves board as in eaves board fixed with nails complete all as specified and directed.

Dismantling timber scantling 40 sqm and over in section in any position as in unframed/framed work complete all as specified and directed

M&L 2nd class soft wood (kail) as in scantling clean sawn, complete all as specified and directed

Taking down cement plaster on brick or stone walls incl.raking out joints hacking for key scrubbing down with water etc complete all as specified and directed

M & L 10mm thick rendering on other than fair faces of brick work or concrete surface in CM 1:6 to be finished even and smooth with out using extra cement complete all as specified and directed

M&L for Rendering 10mm thick cement plaster on fair faces of brick or conc. Surfaces in cement mortar 1:4,even and smooth w/o using extra cement complete all as specified and directed

M & L preparing surface of newly plastered walls and applying two coats of oil bond distemper over a coat of wall putty complete all as specified and directed

M & L preparation of new plastered surface and applying two coat of cement base paint of approved tint/ colour on wall including cornices, plasters over a coat of primer complete all as specified and directed

Taking down chowkats or frames n exc 1.5 Sqm each ( without taking off shutters from the frames) complete all as specified and directed

Taking down chowkats or frames exc 1.5 Sqm but n. exc 4.00 Sqm each( without taking off shutters from the frames) complete all as specified and directed

Taking down shutters of any description n exc 1sqm each complete all as specified and directed

S&F 2nd class hard wood plain, solid chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints complete all as specified and directed

S&F 35 mm thick 2nd class hard wood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood (kail) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze et (without sash bars), edges of framing plain,, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section -8 , clause 8.24 (a) complete all as specified and directed

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed

S & F 18/19 mm thick preliminated particle interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screwed to timber frame work as in shelves in kitchen, almirah, cup boards complete all as specified and directed

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specifications and drawings complete all as specified and directed

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered, with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed

S&F butt hinges, medium weight cold rolled, mild steel of size 100 mm complete all as specified and directed

S&F 150 mm long aluminium barrel tower bolts of extruded section and fixed,complete all as specified and directed

S&F 150 mm aluminum alloy handles, fabricated type, anodised complete all as specified and directed

S&F Aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixin glips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S&F Mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

S & F in repair 140mm floor door stopper of aluminium alloy body and tounge, anodised, with hard drawn steel spring ,fixed in floor complete all as specified and directed.

S & F aluminium powder coated openable double window (Gauzed and Glazed) made of the following specifications complete all as specified and directed :- (Net external size will be measured. Following items are included in this unit rate.) (a) Aluminium frame powder coated all around of hollow section 63 mm x 38 mm x 1.50 mm thick. (b) Provn of glazed openable shutter of section 44 mm x 18 mm x 1.25 mm provided with 3.50 mm thick tinted glass with suitable EPDM beading,02 Nos 100mm powder coated aluminium hinges, 02 Nos 100 mm long powder coated aluminium tower bolts, 01 Nos100 mm powder coated aluminium handle and 01 No hook & eye & any other fitting reqd for each shutter. (c) -ditto- as in para 10 (b) above but using stainless steel wiremesh 0.36 mm dia and 1.40 mm aperature in lieu of 3.50 mm thick tinted glass. (d) Aluminium powder coated grill of weight not less than 2.60 Kg/Sqm on external side with suitable frame/aluminium runner to be fixed on the window frame. (e) Repair to the jamb, cills and all sides around the window is incl in unit rate. The repair finishes to match the existing surfaces like tiles, plastering etc. (Make:-Jindal)

S & F aluminium powder coated ventilators made of the following specifications complete all as specified and directed :- (Net external size of ventilator shall be measured Following items are included in this unit rate.) (a) Aluminium frame powder coated stiles, bottom, top and middle rail of hollow section 50 mm x 25 mm x 1.80 mm thick. (b) Lower portion of ventilator shall be fixed with 3 mm thick pin headed glass fixed with suitable aluminium beading clips and EPDM beading (rubber). (c) Upper portion shall be fixed with aluminium powder coated louver guides fixed with 3 mm thick pinheaded glass with suitable EPDM beading incl suitable handle and clips. (d) Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with suitable frame in upper panel. (e) Repair to the jamb, cills and all sides around the window is incl in unit rate. The repair finishes to match the existing surfaces like tiles, plastering etc.

S&F aluminium door air tight anodized frame made of size 100x45mm of sheet thickness 1.5mm with one or more rebate including jointing cleats hinges etc for fixing anodized aluminium door shutter fully paneled )two NOs of panel on each shutter) with 5.5 mm thick tinted plain glass shutter rail made of 80x45mm of sheet thickness 1.5mm (top, bottom, middle and side rail). Single/double leaf side hung type including necessary joint cleats, anodized aluminium fitting/aluminium fitting such as aluminium butt hinges 100mm long 4 NOs on each shutter, aluminium anodized tower bolt 200mm long 3 NOs for each door, aluminium anodized handle 150 mm 2 NOs ‘D’ type for each. Shutter & locking 6 lever of make Harrison one on each door, bottom door spring one on each shutter including hydrullic door closer complete all as specified and directed Note:- All door fitting except cleat shall be ISI marked (size of each door shall be as per site requirement).

S & F in replacement curtain rod 20 mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and directed Note:- The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account.

M & L preparing old surface of walls and applying two coats of oil bond distemper over a coat of wall putty complete all as specified and directed

M&L Preparing old surface of walls and applying two coats of cement base paint complete all as specified and directed

S & F 12mm Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed

S & F 18mm Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed

S&F butt hinges, medium weight cold rolled, mild steel of size 50 mm complete all as specified and directed

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and directed

S&F Ball catcher with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified and directed

Dismantling of wall and ceiling boards (fiber pulp, insulation, etc..) or unsulation boards/slabs, any thickness, including cover fillets complete all as specified and directed

S&F 2nd class soft wood plain clean sawn fillets square, rectangular or triangular in section exc 6 & n.exc 13 sqcm secured with nails or brads complete all as specified and directed

M&L for 6mm thick plywood, grade BWR, type BB, fixed with nails to timber frame work, fixed in ceiling complete all as specified and directed

M&L for 6mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed in wall/ceiling with screws to timber frame work complete all as specified and directed

M&L for preparation of new wood and wood based surfaces of any description exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floor and paving n.exe 15 cm thickness (below or above ground level) complete all as specified and directed

Dismantling floor, hearth or wall tiling including CM bedding (but not backing), skirting complete all as specified and directed

M & L 75 mm thick PCC 1:2:4 Type B-2 (using 40 mm graded aggregate ) for floor, footpath etc complete all as specified and directed

M & L 25 mm thick PCC 1:2:4 Type B-1 (using 20 mm graded aggregate ) for floor, footpath etc complete all as specified and directed

M&L Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular polished, area of each tiles exceeding 0.42 sqm and not exceeding 1.00sqm, in floors etc. set and jointed in neat cement slurry and pointed in cement to match white or coloured and including 15mm thick screed bed in cement mortar 1:4 , complete all as specified and directed

M&L Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces ,dado /skirting etc set and jointed in neat cement slurry and pointed in cement to match white or coloured and including 10mm thick bedding layers in cement mortar 1:3 complete all as specified and directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles and including 15mm thick screed bed in cement mortar 1:4 ,complete all as specified and directed

M&L Glazed ceramic colour tiles in vertical surface 350x 250x 7 mm/ 450X350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick bedding layers in cement mortar 1:3 complete all as specified and directed.

M&L Virified Ceramic light shade tiles 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in cement to match white or coloured and including 15mm thick screed bed in cement mortar 1:4 ,complete all as specified and directed

M&L Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces ,skirting,dado etc set and jointed in neat cement slurry and pointed in cement to match white or coloured and including 10mm thick bedding layers in cement mortar 1:3 complete all as specified and directed.

M & L 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection / hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed

S&F 6MM thick Non asbestos fibre cement designer board /pre Laminated self embossed texture designer board E-Board classic size 600x600 m ,HPSC (High pressure steam cured) to be fixed or inserted to pre laminated GI Frame work for Seamless ceiling size 600mmx600mm with main runner 38x24x0.9mm thick cross tee 8.6x0.9mm and wall angle 19x19x0.9mm duly suspended with 6mm dia GI bar hanger 1200mm centre to center both ways fixed with steel dash fasteners or from purlin from the roof with alignment dip complete as per manufacturer's instructions complete all as specified and directed (Note: Removing & Refixing of electric fittings & wiring is responsible of contractor with any extra cost )

Dismantling stone slabs and tiles of any description or thickness in floors/wall etc laid bedded and pointed in any mortar complete all as specified and directed

M&L for Granite (of any type) work ,20 mm thick, (table rubbed and polished) in steps jambs , pillars ,window cills ,cooking platforms ,and the like in cement mortar (1:4) including pointing in white cement (1;2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Taking up or down steel tubing 15 mm dia and connections and stacking neatly for offering credit complete all as specified and directed

S & F Tubes, medium grade galvanised, 15 mm bore with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed

Taking up or down steel tubing 20 mm dia and connections and stacking neatly for offering credit complete all as specified and directed

S & F Tubes, medium grade galvanised, 20 mm bore with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed

S&F in repair, plate rack of overall size 24 x 24 x 10 inch made out of 0.63mm thick stainless steel sheet complete all as specified and directed

S&F in repair kitchen sinks with drainage board made of stainless steel 1mm thick with plugs, washers and waster, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and conneting union to pipe overall size 915mm x 460mm bowl size 410 x 330 x 160mm complete all as specified and directed

S& F in Repair white wall mounted Cabinet Mirror of size 14x 18x 4 inch complete all as specified and directed

S&F in repair Corner glass shelf 300mm complete all as specified and directed

S&F in repair glass shelf 500x60mm (with ABS Brackets) complete all as specified and directed

S&F in repair wall mixture /Shower mixer 3-in-1 complete all as specified and directed

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed

S&F in repairs CP brass shower rose with swival joints complete fancy type for 15mm bore pipe, complete all as specified and directed.

S&F in repair 15 mm dia bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of size 15 mm dia and confirming to IS-781-1977 , complete all as specified and directed.

S&F in repairs 15 mm bore, Stop valves/Angle valves chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair CP Mixer single lever basin mixer fancy type for WHB / Sink with double action for hot/Cold water complete all as specified and directed

S&F in repair Towel Ring complete all as specified and directed.

S & F Vitreous china wash basin white flat back size 580x450 mm excluding taps waste chain and plug and porcelain stopper but including brackets including 15 mm bore centre hole mixer fixed complete alongwith pedestal complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan with fixing bolts, trap (pedestal pattern), white, (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs PVC flushing cisterns 10 ltrs capacity including flushing pipe and connections complete all as specified and directed.

S&F in repair 15mm dia PVC connection pipe 450mm long with PTMT nuts of suitable size at both ends complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, 75mm dia bore plain with grating including jointing with solvent cement complete all as specified and directed

S/F water storage tank 500 ltr capacity HDPE triple layer, white coloured, conforming to IS , fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, PVC valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site,complete all as specified and directed.

M & L brick work with sub class 'B' bricks straight or curved on plan to any radius built in CM 1 : 4 in half brick thick walls complete all as specified and directed.

S & F TMT steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia but in stirrups complete all as specified and directed.

M & L RCC 1 : 2 : 4 Type B1 ( 20 MM graded aggregate) as in slabs supported on walls beam and colums in floors, roofs, landind, deck slabs and shelves and the like complete all as specified and directed.

M & L for Use & waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Demolition of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc, complete all as specified and directed.

S&F in repair Soap Dish complete all as specified and directed.

S&F in repair Toilet paper holder complete all as specified and directed.

S&F in repair PVC(SWR)single socketed in any length with rubber ring joint fixed with wall of 110mm as in rain water pipe complete all as specified and directed

S&F in repair PVC(SWR) bends any radius 110mm complete all as specified and directed

S&F 12 mm thick Plywood, grade BWR, type BB, fixed with nails to timber frame work commercial type as in wall fixed with nails complete all as specified and directed

Excavation in trenches, n exc 1.5 m and n exc 1.5 m wide and exc 1.5 m in depth for foundation , etc. or for shafts, wells , cesspits, manholes, pier holes , etc . N exc 10 sqmm on plan and n exc m in depth and getting out in soft/loose soil complete all as specified and directed.

M & L PCC 1:4:8 Type D2 (40 mm graded crushed stone aggregates) as in foundation and mass concrete complete all as specified and directed.

M & L brick work with sub class 'B' bricks straight or curved on plan to any radius built in CM 1: 6 in brick walls complete all as specified and directed.

M & L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M & L broken stone hardcore of gauge n exc. 63mm, deposied, spread and levelled in layers n exc. 15com think, watered and rammed to a true surface complete all as specified and directed.

M & L 75 mm thick PCC 1:4:8 Type D2 ( 40mm graded aggregate) as in sub base to floors complete all as specified and directed.

M & L 40 mm thick PCC 1:2:4 Type B-1 ( using 20 m graded aggregate ) without using extra cement finishing cement concrete surface even and smooth complete all as specified and directed.

S&F wooden laminated flooring 1200x1200x8- 10mm thick with adhesive and base as specified by manufacturer , including 12 mm thick BWR plywood and necessary farme work and finally finishing with french polish ( two or more coats ) and fixed complete all as specified and directed .

M & L 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and rough surface complete all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers n exc 25 cm in soft/loose soil complete all as specified and directed.

M & L Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

S&F aluminium anodised partly glazed door shutter side hung type with style, rails ( Top, Bottom 7 lock rail), Top rail meeting style, lock rail of size 48 x 44 mm, bottom rail 108 x 44 mm, frame for chowkat size 38 x 63 mm, all are made from anodised aluminium section including necessary jointing cleat, glazing, clips rubber packing, anodised aluninium snap beading, screws of suitable size including 5mm thick sheet glass, partical board and suitable size aluminium anodised handle, src complete all as specified and directed.Note:- ( thickness of aluminium section shall not be less than 1.5 mm )

S & F powder coated aluminium ventilator shutters with frame ( aluminium section weighting 0.55Kg/m), fixed with out sash bars, openable type ( Top hung double shutter) and glazing complete with 5.5 mm thick coloured/tinted sheet glass and Aluminium wire mesh with necessary clips, hingesm aluminium ( anodised) peg stay 30 cm long-01 No. with aluminium ( anodised) grill made out of 7mm wide flat, square, rectangular or similar section, fixed with channel of size 38mmm x 12 mm x 13mm (Section 8778) complete all as per manufacturer's catalogue 7 specifications (make: Grill No. 20 of "DECOR GRILL" or complete all as shown on drg No. CEAA/64 complete all as specified and directed

M & L Roof trusses ( framed), trussed, purlins,crane gantries, rails and fastening and heavy pieces , cleats src . Of Gde Fe 410 W (Gde-E250) Qty-A complete all as specified and directed.

M & L for Australlian wood panelling 10mm thick including 9mm thick BWR plywood on the wall and finally finishing with french polish (two or more coats) and fixed complete all as specified and directed.

M & L for Khatamband pattern false cellling , design as approved by GE with ornamental wood work made out of stainless including 12mm thick BWR plywood and necessary framework and finally finishing with french polish ( two or more coats) and fixed complete all as specified and directed

S & F aluminium anodised snap grid ceiling of frame size 600x600mm, main tee section of size 36.5mmx25mm x1.4mm thick, cross tee section of size 23.5mmx26.4mmx 1.4m thick, supported at ends all along the wall with aluminium anodised angle of size 40mmx 25 mm x 2mm thick and 4mm dia GI suspenders including Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed.

S & F EWC cascade with all fittings and accessories all as per manufactures instruction, complete all as specified and directed

S&F ceramic gents urinal Automatic wall mounted type with all fittings and accessories all as per manufactures instruction, complete all as specied and directed

S & F Vitreous China wash basin, size 550x 400mm white , flat back , with waste, coupling, chain and plug and porcelean stopper & backets including cutting for and pinning in end of brackets but excluding tap complete as specified and directed.

S&F CP body cleaner Health faucet with 1Mtr tube and hook ( Baded tube) white/lvory complete all as specified and directed.

S&F toilet paper holder CP fixed to walls with brass screws complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F 15mm bore, Stop valves , chromium plated, screwed down , high pressure , crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 15mm bore bib taps chromium plated , fancy type,with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F brass chromium plated tubular towel rail 20mm dia including brackets complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single sockets , in any length with rubber ring joints, laid in trenches or floors complete all as specified and directed.

S&F PVC (SWR) bends 75mm dia radius complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank ( cylindrical, vertical with closed top ) hoisted and fixed in position incl all accessories of capacity 500ltrs including fitting ball valve high pressure of PTMT with epoxy coated aluminum rod & high density plastics ball screwed for iron pipe of size 15mm dia complete all as specified and directed.

M and L PCC 1:4:8 Type D2 (40mm graded aggregate) as in bed to drain pipes 100mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M & L 100mm Sail-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed.

M & L 100mm PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade and no pigment complete all as specified and directed and no pigment complete all as specified and directed .

S&F 2nd class hard wood clean sawn timber fixed in scantling complete all as specified and directed

M&L for 6mm thick plywood, grade BWR, type BB, fixed with nails to timber frame work, fixed in wall complete all as specified and directed.

S& F Second class soft wood plain filters square , rectangular or triangular in section , clean sawn, secured with nails, cross sectional area exc 13 and n. exc 25 Sqcm as specified and directed

S & F in repair curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

Dismantling boarding, any description, fixed in any position complete all as specified and directed.

S & F 20mm thick, second class hard wood boarding clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves boards, etc complete as specified and directed

M & L preparation of old wooden surfaces of any description , not other wise described, over 10cm width or girth including and applying one coat of synthetic enamel paint complete as specified and directed

M & L 100 mm thick PCC 1:2:4 Type B-2 (40 mm graded aggregate ) as on floor, path complete as specified and directed

M & L for chequered concrete tiles 30cm x 30cm x 25mm thick set , joined and pointed in neat cement slurry in floors bed in cement motar 1:4, complete all as specified and directed

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed

S & F Mild steel work as a wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

M & L preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer over newly prepared steel surface complete all as specified and directed

M&L preparing new steel surface n exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M & L Providing cement concrete type B2, 1:2:4 (40 mm graded aggregate) surface channels and drains complete all as specified and directed

M & L PCC 1 : 2 : 4 Type B1 ( 20 mm graded aggregate) as in providing, cement concrete inlintel up to 1.5m clear span, cills, steps, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed

M & L Precast RCC 1 : 2 : 4 Type B1 ( 20 MM graded aggregate) as in cover slab (for manholes etc), chajjas, mangers, shelves etc. set in cm 1 : 6 complete with joints to math complete all as specified and directed

S & F mild steel work in framed work as in doors or gates of angle or other sections, prepared for hanging with and including either hooks and hinges, and hanging also fastening and fixing complete conforming to Gde Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed

M&L for taking down carefully existing old burnt out / unserviceable aluminium / copper point wiring system any type/ size and any description complete for light, fan,bell,socket, power points etc complete including removing the all type of fittings & fixture alongwith it connected fixing acessories such as all switches, sockets, ceiling roses, holder,regulators,bell etc complete and removing of all the old materials from the site for to taking as a schedule of credit complete all as specified and directed.

Dismantling unserviceable main switch/DBs with MCBs complete all as specified and directed.

Taking down carefully electric water heater of any capacity from site and repair it if required and refixing the same position with entire satisfaction complete all as specified and directed.

Taking down unserviciable Ceiling fan from site and deposiated in MES store yard carefully with entire satisfaction complete all as specified and directed.

M&L for making single phasing point wiring system used as copper conductor wire for phase and neutral wiring system the wire made out of PVC insulated FRLS of 1100 volt grade with having multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) ISI marked drawn through wiring system surface on wall or concealed in wall with the help of heavy duty ISI mark PVC casing capping strip / PVC conduit pipe ISI mark in any lengthy wiring system and along with its all connected fittings accessories including providing of pressed steel terminal sunken boxes or heavy duty PVC box and duly fixed it concealed in wall or surface on wall and alongwith providing of back and face top covered plate frame or electro plated plastic laminated sheet for housing / mounting of any type/size switches sockets, regulators etc and including using /drawing of one run of single wire 1.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI marked with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making the good to all disturbed surfaces of wall/ceiling area of new wiring system and to match to it as per the existing surface of wall/ceiling etc complete all as specified and directed.

Description all as per serial item No 149 above but one light point / fan/Bell/exhaust fan/wall fan /ceiling fan point wiring system controlled by one way switch complete all as specified and directed.

Description all as per serial item No 149 above but one 3 pin 5 Amp switch socket outlet point wiring system fixed on same board & controlled by one way switch complete all as specified and directed.

Description all as per serial item No 149 above but one 3 pin 5 Amp switch socket outlet point wiring system fixed on independent board & controlled by one way switch complete all as specified and directed.

Description all as per serial item No 149 above but one bell point wiring system fixed on board and controlled by one way bell switch complete all as specified and directed.

Description all as per serial item No 149 above but using PVC insulated FRLS wire 1100 volt grade with multistranded copper conductor wire of size 2.5 Sq. mm (Nominal area) ISI Marked for power socket point on indenpent board point wiring system and also providing of 2.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI Marked with multistranded copper conductor wire used as a continuous earth wire for power point wiring system complete all as specified and directed.

Description all as per serial item No 149 above but using single runs of PVC insulated FRLS wire ,1100 volt grade with multistranded copper conductor wire of size 4 Sq.mm (Nominal area) ISI Marked for high power wiring system with fixed on independent board and also providing of 4 sqmm PVC insulated FRLS wire 1100 volt grade ISI Marked with multistranded copper conductor wire used as continuous earth wire complete all as specified and directed.

Supply & fixing of modular type switch one way 5/6 Amps 220 Volts AC,one module complete all as specified and directed.

Supply and fixing of modular type socket of 5/6 Amps 220 Volts AC, 3/5 multi pin type with two module complete all as specified and directed.

Supply and fixing of modular type switch of 15/16 Amps 220 Volts AC one module complete all as specified and directed.

Supply and fixing of modular type socket of 15/16 Amps 220 Volts AC 5/6 multi pin type with two module complete all as specified and directed.

Supply and fixing of modular type bell push flush type single pole one way complete all as specified and directed.

Supply and fixing of bell Ding Dong Type, 220 volt AC, Single Pole complete all as specified and directed.

Supply and fixing of one/two modular type step type electronic fan regulator with having hum free step alongwith speed control know complete all as specified and directed.

Supply and fixing ceiling rose three terminals type made out of polycarbonate , isolated body complete all as specified and directed.

Supply and fixing of LED tube light fitting of 1x 20W/22W 220V AC decorative box type with driver, holder including LED tube light with having energy efficient type use in both warm/white type colour complete including providing of suitable type flate fexible cable for electric connection from ceiling rose to fitting comlplete and including taking down of old fitting complete all as specified and directed.

S & F in replacement energy saving long life recessed/Celling Conceled/Surface mounted flat unique square slim/Ultra slim panel (as per site requirement) integrated design LED luminire light panel type fitting of size 2 X 2 feet of type of rating wattage capacity 36W/40W of supply voltage 220 AC decorative type with high performance LEDs and electronic driver with extruded body made of aluminium housing with mounting slot and fully diffused recessed mounted LED luminire high quality with surge protection energy efficient for ready to use and required in Warm type colour fixture complete including making suitable type of size hole/Square type wooden frame work on ceiling surface or in additional of extra cutting of existing hole side work(if required at site) for fixing of light fitting purposed and also providing suitable type flat flexible three core cable for electric connection purposed complete all as specified and directed.

Supply and fixing of LED mirror light fitting with high out put diffuuser 2 feet long of 10 Watt 220 volt AC decorative type with driver holder and LED lamp with having energy efficient type use in both warm/white type colour complete light fitting set all as per existing fitting type/ size of sample /model and make and including providing of suitable type flate fexible cable for electric connection from ceiling rose to fitting and making electric connection and including taking down of old fitting complete all as specified and directed.

Supply and fixing surface mounted LED decorative type angle adjustable sport light / bed side study lamp light fitting with lamp in matt finish for premium aesthetics with based of suitable rating capacity 7Watt LED complete light fitting set all as per existing fitting type/ size of sample /model and make and required fitting use in both warm/white type colour complete light fitting and including providing of suitable type of flate fexible two/three core cable and making electric connection and including taking down of old fitting complete all as specified and directed.

Supply and fix in repair of LED street light/security light fitting for buildings of rated capacity 35 Watt 230 volt AC with having LED driver,lamp bracket with impact and corrosion resistant with lense embeded including thermal management in multiple optices complete with IP 65/66 protectiuon suitable for out door type made out of high pressure die cast hosing with heat resistant glass complete including providing of suitable size of dia GI pipe light grade bracket and it to match/setting the new fitting fixture hole attechment system of suitable bracket length upto 1.0 mtr long and make to shape / bend of 120 degree angle including duly fixed alongwith existing pole /bldg wall/ roof with the help of 02 Nos of MS fixing clamp alongwith nut bolt and including providing of suitable type of flate fexible two/three core cable and making electric connection complete all as specified and directed.

Supply and fixing of sheet metal enclosure duly powder coated with single pole and neural enclosure with having a two pin and earth plug & top and mounting chanel alongwith one 01 MCB SP 20 Amp and dully fixed surface on wall or concealed in wall and making all necessary electrical connection complete all as specified and directed.

Supply and fixing of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrengment system suitable of size/type of distribution board of rating SPN 8 way type 220 volt AC supply system with IP protection rating with ISI marked and having neutral and earth link bus bar and mounting base chanel suitable for holding MCBs incommer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing meter and DBs complete all as specified and directed.

Supply and fixing of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrengment system suitable of size/type of distribution board of rating SPN 4 way type 220 volt AC supply system with IP protection rating with ISI marked and having neutral and earth link bus bar and mounting base chanel suitable for holding MCBs incommer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing meter and DBs complete all as specified and directed.

Supply and fixing of MCB SPN 40 to 63 Amps with breaking capacity 10KA 'C' Curve series, 220 Volts, 50 Hz AC supply complete and also making suitable size / type of electric wiring connection complete all as specified and directed.

S&F MCB SP 40 to 63 Amp with breaking capacity, 10 kA rupturing capacity 'C' series 50 HZ AC supply and also making suitable size/type of electric wiring connection complete all as specified and directed.

Supply and fixing of MCB SP 06 to 32 Amps with breaking capacity 10KA 'C' Curve series, 220 Volts, 50 Hz AC supply complete and also making suitable size / type of electric wiring coneenection complete all as specified and directed.

Supply and fixing of Sub main wiring system with two runs PVC insulated FRLS wire,1100 volt grade with multistranded copper conductor wire of size 2 Run of 6 Sqmm and 1 Run of 6 Sqmm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old unservicable sub main wiring system complete and making good all disturbed surfaces match to the existing surface complete all as specified and directed Note:- 3 run of 6 sqmm wire and 1 run of PVC casing /Conduit shall be measured as 1 RM.

Supply and fixing of Sub main wiring system with two runs PVC insulated FRLS wire,1100 volt grade with multistranded copper conductor wire of size 2 Run of 10 Sqmm and 1 Run of 10 Sqmm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old unservicable sub main wiring system complete and making good all disturbed surfaces match to the existing surface complete all as specified and directed Note:- 3 run of 10 sqmm wire and 1 run of PVC casing /Conduit shall be measured as 1 RM.

S&F star rated electric ceiling fan 1200mm sweep min air delivery 210 CFM with service value 6.0 BEE norms 5 star rating with bruhless direct current motor (BLDC) of single phase 230 volt AC alongwith blade, down rod, canopy, clamps with reel insulator, electronic regulator & accessories and MS fan hook fixed in ceiling/roof including providig flate flexible copper wire and making all electrical connection complete all as specified and directed.

S & F and testing star rated of electric ventilation exhaust fan of Size 250mm sweep complete Ac single phase 230 volt and made out of sturdy engineering plastic body complete with blade and lowers with shutter and also or making of suitable type/size of hole on wall of any type of wall construction work for installation/fixing of exhaust fan after fan fixing work making good to all disturbed hole surface area of wall/ceiling and floor area of hole system and to match/dressing to it as per the existing surface on wall/floor/ceiling etc by cement plastering work complete all as specified and directed.

M&L for earthing work complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level and connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers of galvanised steel and to be protected by GI pipe 15 mm bore light grade & connected to earth test point/main switch board or main control board and also providing charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil all as shown in Electrical Plate No 3 of SSR part -I. and also making arrangment of 20 mm dia bore galvanised iron pipe (medium grade) for water and making funnel, wire mesh,and also including provision of concrete pit cover framing work in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 Kg/Sqm) and outer frame work of angle iron 25x25x6mm with top concrete pit cover and handle for lifting of cover complete all as specified and directed.

Taking down carefully Air condition of any capacity from site and refixing the same position after filling the gas and complete connected items such as copper pipe,brazing itm,insulation etc with entire satisfaction of Engr-in charge.

Supply and fix in repair recessed/ceiling concealed mounted down lighter light fitting of round/Square flate shapes decorative type with high efficiency PMMA fiffuser soft glare free light with drivers & LED luminaire of rating capacity in 15 Watt to 18 Watt 220 volt AC complete light fitting set all as per existing fitting type/ size of sample /model and make and including making in cutting or additional extra corner cutting work on existing hole of ceiling surface (when if required at site) for setting & fixing of new light fitting complete including making in additional extra corner cutting work on existing hole of ceiling surface (when if required at site) for setting & fixing of new light fitting complete and also providing of suitable type of flate fexible two/three core cable and making electric connection complete all as specified and directed.

Supply, fixing, commissioning and testing of 3 star rated wall mounted split AC, dual invertor based with cooling and heating function and digital inverter type complete set of hi wall split type indoor and outdoor complete set of air conditioner unit with cardless remote control and full filling of initial refrigent gas alongwith having inbuilt heating and cooling arrangement and digital inverter twin rotary type compressor suitable for AC of rating capacity 2.0 TR and suitable for operation of 230Volt 50Hz single phase electric supply including provn of MS stand & bracket for fixing of outdoor and indoor unit system and also providing of both type /size sunction and discharge coper refrigerant piping attachment system of any length and duly both connected it from outdoor unit to indoor unit system alongwith duly overlapped it by nitrile insulation, with insulation taping work and suitable drain pipe line system upto ground level for dropping out the water outside from evaporator unit and making electric connection with three core copper cable of suitable size and making hole on wall / roof and making good all disturbed surface as per existing complete all as specified and directed.

Supply, fixing, commissioning and testing of wall mounting hanging based automatic digital operation based voltage stabilizer with copper winding based unit of single phase naturally air cooled indoor type with having digital display and suitable for operation on single phase AC supply and with having designed voltage for input & output voltage 90 volt to 230 volt with accuracy +2.5% and having low and high voltage cut low voltage cut off 90 (-) 5 volts high voltage cut off 230 V (+5) Volts along with start time delay system with time delay adjustable from 30 second to 1.5 minutes system complete unit set of rating capacity 5 KVA complete system complete all as specified and directed.

S&F star rated ventilating exhaust fan made out of sturdy engineering plastic body complete with louvers and shutter, 300 mm sweep, 230 Volts AC single phase, 50Hz, 1200 RPM, coper winding including making of suitable type /size of hole on any type of wall and fixing compete with nut, bolt etc and making good distrubed surface of wall/ceiling & finishes to match and providig flate flexible copper wire & making all electrical connection complete all as specified and directed.

S & F in repair Surface mounted decorative wall mounted bracket light fitting with having gold finish fixture with cognac hammered clear glass diffuser suitable for 7.5W LED filament E-27 base including providing of 1XN 9W LED lamp/1NX7.5W LED filament lamp complete light fitting with having bulb holder based adaptor alongwith providing 01 No of 7W/9W LED bulb in required fitting use in both Warm/White type colour complete set including providing suitable type of flat flexible two/three core cable and making electric connection complete all as specified and directed.

S & F Wall mounting fan 400mm sweep, pull cord oscillating type, single piece AS blade, 3 speed, pull cord control with complete arangement of fixing on wall, including frame work with MS fastener,nut and bolts complete all as specified and directed.

Material and labour for sub main wiring with two runs of single core FRLS PVC insulated, multistranded unsheathed copper conductor cable of size 4.0 square mm and drawing through PVC conduit of 20mm dia with accessories on concealed in wall/roof along with one run of 4.0 square mm FRLS PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board duly making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed. Note: 3 runs of 4.0 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre.

S & F sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangment system suitable of rating of size/type of distribution board SPN 12 way type 220 volt AC supply system with IP-43 protection system and having mounting chanel with having suitable rating of copper bus bar and suitable size of common neutral and earth link and also making all necessary electrical connection and duly fixed surface on wall or conceled in wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and as directed.

Notes :- An amount of Rs 146082.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

Alishan Builders (BID ID -3415547)

M/S Vivek Gupta and Co (BID ID -3408717)

M/S D N Enterprises (BID ID -3406584)

M/S STARE BUILDERS (BID ID -3414867)

M/S AIJAZ ENTERPRISES (BID ID -3415525)

M/S Tajamul Ah Buchh (BID ID -3408295)