Firefighting, landscaping, STP, UGR and other misc. works for faculty accommodation in Plot-A and Plot-B at IIT Kharagpur

Name of Work: Firefighting, landscaping, STP, UGR and other misc.

works for faculty accommodation in Plot-A and Plot-B at IIT Kharagpur

SUB-HEAD DESCRIPTION AMOUNT

1 UNDER GROUND RESERVOIR 3,740,000.00

2 PLUMBING WORK (DI PIPE CONNECTION) 12,000,000.00

5 PUDDLE FLANGE 100 mm 30,000.00

6 PUDDLE FLANGE 50 mm 14,000.00

7 FIRE HYDRANT SYSTEM 12,800,000.00

8 LANDSCAPING & HORTICULTURE 2,700,000.00

GRAND TOTAL 36,564,000.00

GRAND TOTAL 36,564,000.00

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

SUB-HEAD-1: UNDER GROUND RESERVOIR

Earth work in excavation by mechanical means (hydraulic

excavator)/ manual means over areas (exceeding 30 cm in depth,

1 2.6 1.5m in width as well as 10 sq.m on plan) including disposal of

excavated earth, lead upto 50m & lift upto 1.5m disposed earth to

be levelled and neatly dressed.

Providing and laying in position cement concrete of specified grade

2 4.1 excluding the cost of centering and shuttering - All work upto plinth

1:3:6 (1 cement : 3 coarse sand (Zone-III) derived from natural

4.1.6 sources: 6 graded stone aggregate 40 mm nominal size derived Cum. 12.03 7,178.75 86,336.67

from natural sources)

Providing and laying in position cement concrete of specified grade

4 4.1 excluding the cost of centering and shuttering - All work upto plinth

1:4:8 (1 cement : 4 coarse sand (Zone-III) derived from natural

4.1.8 sources: 8 graded stone aggregate 40 mm nominal size derived Cum. 59.97 6,812.00 408,506.85

from natural sources)

Providing and laying in position ready mixed or site batched design

mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but

5 5.33 excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge, for the

following grades of concrete.:

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.1 All work upto plinth level

M-25 grade reinforced cement concrete with minimum cement

content of 330 kg. per cum of concrete.

5.33.2 All work above plinth level upto floor V level

M-25 grade reinforced cement concrete with minimum cement

content of 330 kg. per cum of concrete.

Centring & shuttering including strutting,proping etc for removal of

Wall (any thickness) including attached pilaster, butresses, plinth &

string courses etc.

Centring & shuttering including strutting,proping etc for removal of

5.9.3 Suspended floors,roofs,landings,balconies and access platform Sqm. 110.00 927.25 101,997.50

Brick work with non modular flyash lime brick (FALG Bricks)

conforming to IS 12894 class designation 10 average in

superstructure above plinth level up to floor V level in all shapes and

6.34.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum. 12.86 8,752.55 112,579.67

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

Steel reinforcement for R.C.C. work including straightening, cutting,

8 5.22 bending, placing in position and binding all complete upto plinth

level. - thermo Machnically Treated bars.

5.22.6 thermo Machnically Treated bars of grade Fe-500D or more. Kg 14647.00 107.85 1,579,678.53

15 mm cement plaster on rough side of single or half brick wall

finished with a floating coat of neat cement of mix

10 13.4 12 mm cement plaster of mix :

11 13.16 6 mm cement plaster of mix :

SUB-HEAD-1: TOTAL 3,740,000.00

SUB-HEAD-2: PLUMBING WORK (DI PIPE CONNECTION)

Excavating trenches by mechanical/ manual means of required

width for pipes, cables etc. Including excavation for sockets, and

dressing of sides, ramming of bottoms, depth upto 1.5M including

getting out the excavated soil, and then returning the soil as

required, in layers not exceeding 20 cms in depth including

consolidating each deposited layer by ramming, watering, etc.

And disposing of surplus excavated soil as directed within a lead of

2.10.1 All kind of soil

Pipes, cables etc, exceeding 80mm dia but not exeeding 300 mm

Filling available excavated earth (excluding rock) in

13 2.25 trenches,plinth,sides of foundation etc in layers not exceeding 20 Cum. 2800.00 196.00 548,800.00

cm in depth. Consolidating each deposited layer by ramming

Extra for every additional lift of 1.5 m or part thereof in excavation /

banking excavated or stacked materials.

Providing and laying in position cement concrete of specified grade

15 4.1 excluding the cost of centering and shuttering - All work upto plinth

1:3:6 (1 cement : 3 coarse sand (Zone-III) derived from natural

4.1.6 sources: 6 graded stone aggregate 40 mm nominal size derived Cum. 55.00 7,178.75 394,831.25

from natural sources)

Constructing masonary chamber 90x90x100cm, in brick work in

cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve

with C.I. Surface box 100 mm top diameter,160 mm diameter &

180 mm deep with channel lid & RCC top slab 1:2:4 (1 cement:2

coarse sand:4 graded stone aggregate 20mm nominal size)

necessary excavation foundation concrete 1:5:10 (1 cement:5 fine

sand: 10 graded stone aggregate 40mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse sand)

12mm thick finished with a floating coat of neat cement complete as

per standard design

with common burnt clay F.P.S (non modular ) bricks of class

designation 7.5

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

Constructing brick masonry manhole in cement mortar 1:4 ( 1

cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal

size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8

graded stone aggregate 40 mm 1:4:8 mix (1 cement : 4 coarse

sand : 8 graded stone aggregate 40 mm nominal size), inside

plastering 12 mm thick with cement mortar 1:3 (1 cement : 3

coarse sand) finished with floating coat of neat cement and making

channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) finished with a

of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with

frame (light duty) 455x610 mm internal dimensions, total weight of

cover and frame to be not less than 38 kg (weight of cover 23kg

and weight of frame 15 kg)

With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with

frame (heavy duty) 560 mm internal dimensions, total weight of

cover and frame to be not less than 208 kg (weight of cover 108kg

and weight of frame 100kg)

With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5

19 19.8 Extra for depth for manholes

19.8.1 Size 90x80 cm

With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5

With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5

Providing and laying in position cement concrete of specified grade

21 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural

4.1.4 sources: 4 graded stone aggregate 40 mm nominal size derived Cum. 21.60 7,780.30 168,054.48

from natural sources)

Providing & laying D.I. specials of class K-12 suitable for push-on

jointing as per IS :9523

Providing & laying C.I. Sluice valve (with cap) complete with

23 18.31 bolts,nuts,rubber insertion etc (the tail pieces if required will be paid

18.31.1 100 mm diameter

18.31.3 150 mm diameter

24 1215 Welding by electric plant Cm 3600.00 2.50 9,000.00

Providing & laying Double Flanged (screwed/welded) centrifugally

(spun) ductile Iron pipes of class K -9 CONFORMING TO IS :8329

18.73.1 100 MM Dia Ductile Iron Double Flanged Metre 171.00 1,821.55 311,485.05

18.73.2 150 MM Dia Ductile Iron Double Flanged Metre 1639.06 2,607.50 4,273,847.63

Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or

26 18.7 Ductile Iron Pipes including testing of joints and the cost of rubber

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

Providing and laying D.I. specials of class K-12 suitable for push-on

jointing as per IS : 9523

Providing and laying D.I. Specials of Class K - 12 suitable for

mechanical jointing as per IS : 9523

29 18.72 Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron

18.72.15 100 mm dia Ductile Iron Class K-9 pipes Metre 1000.00 1,344.60 1,344,600.00

18.72.16 150 mm dia Ductile Iron Class K-9 pipes Metre 500.00 1,837.75 918,875.00

Providing Flanged Joints to double flanged C.I/D.I pipes and

specials,including testing of joints

Providing & fixing PTMT Ball cock of approved Quality,colourand

31 18.62 make complete with Epoxy coated aluminium rod with L.P/H.P.H.D

18.62.5 50 mm nominal bore,242 mm long,weighing not less than 1240 gms Each 12.00 1,375.95 16,511.40

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings This includes jointing of pipes &

fittings with one step CPVC solvent cement, trenching, refilling &

testing of joints complete as per direction of Engineer in Charge.

Providing and laying non-pressure NP2 class (light duty) R.C.C.

pipes with collars jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement: 2 fine sand) including testing of joints

SUB-HEAD-2: TOTAL 12,000,000.00

SUB-HEAD-3: 100 KLD STP

Earth work in excavation by mechanical means (hydraulic

excavator)/ manual means over areas (exceeding 30 cm in depth,

34 2.6 1.5m in width as well as 10 sq.m on plan) including disposal of

excavated earth, lead upto 50m & lift upto 1.5m disposed earth to

be levelled and neatly dressed.

Providing and laying in position ready mixed or site batched design

mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but

35 5.33 excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge, for the

following grades of concrete.:

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.1 All work upto plinth level

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

M-25 grade reinforced cement concrete with minimum cement

content of 330 kg. per cum of concrete.

Brickwork with common burnt clay F.P.S (non-modular) brick of

class designation 7.5 in foundation and plinth in

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum. 116.82 7,132.25 833,206.71

Centring & shuttering including strutting,proping etc for removal of

5.9.3 Suspended floors,roofs,landings,balconies and access platform Sqm. 319.00 927.25 295,792.75

12 mm cement plaster finished with a floating coat of neat cement

100KLD SEWAGE TREATMENT PLANT BASED ON ANAEROBIC &

AEROBIC TREATMENT PROCESS (excluding civil works)

SUB-HEAD-3: TOTAL 5,280,000.00

SUB-HEAD-4: PUDDLE FLANGE

40 N-DSR Puddle flange in water reservoir 100 mm dia Each 12 2,500.00 30,000.00

SUB-HEAD-4: TOTAL 30,000.00

SUB-HEAD-5: PUDDLE FLANGE

41 N-DSR Puddle flange in water reservoir 50 mm dia Each 6 2,333.33 14,000.00

SUB-HEAD-5: TOTAL 14,000.00

SUB-HEAD-6: FIRE HYDRANT SYSTEM

Providing, Installing, testing, & commissioning of electric driven

42 N-DSR Main Pump suitable for automatic operation consisting of the Set 2.00 477,719.93 955,439.87

Horizontal single end suction centrifugal suction type pump

complete for delivery of 2280 ltrs./minute against a total head of 70

metres and mechanical seal

Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply

of 45KW ( or as per pump efficiency ) rating for the above pump

with synchronous speed of 2900 RPM T.E.F.C. type such as

confirming to IP:55 and flexible coupling and coupling guard with

the pump. with Vibration pads

Common bed plate of fabricated mild steel channel or cast iron type

Supplying, installing, testing, & commissioning of diesel engine

43 N-DSR driven Standby Pump suitable for automatic operation consisting of Nos. 2.00 1,125,551.64 2,251,103.27

the following ( as per specification ).

Horizontal end suction centrifugal suction type pump complete for

delivery of 2280 ltrs./minute against a total head of 70 metres.

Radiator cooled Diesel Engine developing 85 BHP ( or as per Pump

Efficiency ) for the above pump at 1800 RPM, flexible coupling and

coupling guard with the Pump, common bed plate for mounting of

the Engine and Pump, RCC Foundation and vibration damping

arrangement by cushy foot, Diesel Engine starting Panel for starting

of the engine automatically with a unit of battery of Lead Acid 24V,

150 Ah, and battery charger as per specifications. Rate shall also

include Exhaust Pipe of required length and size to discahrge

exhaust gases externally, with muffler, day oil tank of 100 lts

capacity with first charge and hand pump set, , washers as

required. Fuel Tank shall be of 2 mm thick sheet, factory made, and

shall have indications for Low Fuel Switch, Fuel Level Indicator, Shut

off Nozzle and Audible Alarm in Engine Panel. with mechanical seal

and cushy foot mounting

Supplying, Installing, testing, & commissioning of electric driven

automatic pressurisation pump set consisting of the following.

Horizontally mounted centrifugal end suction type Jockey pump

complete for delivery of 180 ltrs./minute against a total head of 70

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

Squirrel cage induction motor suitable for 415 V, 50Hz, AC supply of

9.3KW rating for the above pump with synchronous speed of 2920

RPM T.E.F.C type such as confirming to IP:55 and flexible coupling

and coupling guard with the pump. With mechanical seal

Common bed plate of fabricated mild steel channel or cast iron type.

(Make: KBL/KEC/CG)

Supplying & fixing Cast Iron Sluice Valve PN-1.6 (Flanged) Hand

Wheel Operated, Non-Rising Stainless Steel Stem, Bronze Body Seat

Ring. Flanges Drilled to IS : 1538, Shell Test Pressure - 2.4 MPa

(Hyd.), Seat Test Pressure - 1.6 MPa (Hyd.) of the following size

complete with bolts, nuts, washers and inserted rubber gaskets as

Supplying & fixing Cast Iron Non- Return Valve PN-1.6 (Flanged),

Swing Type with Nitrile Rubber Flap, Flanged Ends to IS:1538 of the

following size complete with bolts, nuts, washers and inserted

rubber gaskets as required

Supplying & fixing Butterfly Valve (Wafer Type), PN-1.6 with S.G

Iron Disc Body S.G. Iron, Lever Operated, Nitrile/EPDM Rubber

47 N-DSR Lining. Seat Test Pressure 1.76 MPa (Hyd.) of the following size

complete with bolts, nuts, washers and inserted rubber gaskets as

100 NB (recirculation Line) Nos. 2 10,014.00 20,028.00

Supplying & fixing Cast Iron Y-Type Strainer, PN-16 (Flanged). Shell

Test Pressure - 24 Kg/cm2g , S.S-304 Perforated Sheet Screen

48 N-DSR ø3mm, Flanged Ends to BS10 Table `F`. of the following size

complete with bolts, nuts, washers and inserted rubber gaskets as

Supplying, testing, installation & commissioning of 150 mm dia

49 N-DSR pressure guages ( stainless steel body ) with cut off valves and Nos. 8.00 4,171.00 33,368.00

Supplying, testing, installation & commissioning of pressure

switches for Fire Pumps

Providing and installing of Resistoflex SS mesh bellows on the

51 N-DSR suction and delivery side of Fire Pumps of the floowing sizes

including flanged ends

Supplying and fixing air vessel made of 450 mm dia, 6 mm thick MS

sheet, 2000 mm in height with air release valve on top and flanged

52 N-DSR connection to Pump House, drain arrangement with 25 mm dia gun Nos. 2.00 44,827.00 89,654.00

metal wheel valve, with required accessories, pressure guage and

painting with synthetic enamel paint of approved shade as required.

Supplying, erection, testing and commissioning of totally enclosed

cubicle type free standing, floor mounted, compartmentalised,

sectionalised, dust, damp and vermin proof, with suitable natural

ventilation arrangement, front and rear accessible, lockable power

cum control panel, fabricated from 1.6 / 2 mm thick MS sheet ( to

give IP 54 protection ) spray painted with approved colour shade,

heavy 4 strip sleeved aluminium / aluminium alloy bus bar, bus bar

supports, interconnecting from busbars to outgoing switches /

MCCBs including earthing the board suitable to accomodate the

following including numbering etc., as required

Cubical panel as described above with following:

Incoming section : 300 Amps MCCB, 3 pole with neutral link 50 KA,

415 V+ 1 No., Digital Voltmeter with phase selection push button =

1 No., 3 Phase indication lamps, instrument fuses and switches, 400

Amp Al. Bus bar

Outgoing Section:

200 A TP MCCB with neutral link 50 KA 415 V = 1 No.

On / Off indicating Lamp = 1 set.

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

Suitable fully automatic star delta starter for motor complete with

single phase preventer relay = 1 no.

Ammeter with Phase selection = 1 No.

CT Ratio 250 : 5 = 3 nos

63 A TP MCCB with neutral link 25 KA 415 V = 1 No.

On / Off indicating Lamp = 1 set.

Suitable fully automatic star delta starter for motor = 1 no.

Digital Ammeter with Phase selection = 1 No.

Cts ratio 50:5 = 3 Nos

One spare outgoing for Main Pump and Jockey Pump. Only space

and busbar extension shall be left in Panel

1 set of automatic trip battery unit of suitable rating operating at 24

V DC, complete with necessary boost / trickle charging

arrangements I/c providing and fixing necessary control system

component such as timer, relays & contactors I/c DC meter, battery

charging and voltmeter meters etc as required for engine driven

Supplying and fixing of one number PVC insulated and PVC sheated

aluminium conductor cable of 1.1 KV grade of size on surface as

required complete with end terminations of aluminium lugs and

brass compression glands.

3C X 70 SQ.mm AL. Armoured Cable Metre 80.00 970.00 77,600.00

3C X 16 SQ.mm AL Armoured Cable Metre 40.00 924.00 36,960.00

12C X 2.5 SQ.mm CU.Armoured Cable Metre 40.00 962.00 38,480.00

2C X 1.5 SQ.mm CU.Armoured Control Cable Metre 90.00 208.00 18,720.00

Supplying, laying, jointing and testing of following sizes MS pipe and

fittings such as Bends, Tees, reducers, rubber insertions and

galvanised nuts and bolts, "Heavy Class" confirming to IS: 3589

with upto date amendments including fixing the pipe on wall /

ceiling with suitable M.S strip / clamps / bracket and painting with

one coat of zinc chromate primer and and two coats of synthetic

enamal paint signal red colour etc. complete as reqd. Pipes shall

have welded connections complete with bevel cut by angle grinder

including all breakages and making good the same. U clamps shall

be 10 mm thick.

Supplying, fabricating and installing following sizes of perforated GI

cable trays including horizontal and vertical bends, reducers, tess,

56 N-DSR cross members and other accessories as required and duly

suspended from the ceiling with MS suspenders and including

painting etc. as required.

225 mm width x 50 mm depth x 1.6 mm thickness Metre 24.00 1,868.00 44,832.00

150 mm width x 50 mm depth x 1.6 mm thickness Metre 24.00 1,438.00 34,512.00

Supplying and fixing suction coupling for fire brigade draw of water

from tank with 100 mm dia pipe and CI Foot valve with Strainer

Supplying and fixing gun metal four way Fire Brigade Collecting

Providing and installing structural steel for pipe supports including

59 N-DSR cutting, welding , nuts, bolts complete as required Steelwork shall Kgs 2250.00 172.00 387,000.00

be painted with primer and 2 coats of enamel paint

Supplying, laying, jointing and testing of following sizes MS pipe and

fittings such as Bends, Tees, reducers, rubber insertions and

galvanised nuts and bolts, "Heavy Class" confirming to IS: 3589

with upto date amendments including fixing the pipe on wall /

ceiling with suitable M.S strip / clamps / bracket and painting with

one coat of zinc chromate primer and and two coats of synthetic

enamal paint signal red colour etc. complete as reqd. Pipes shall

have welded connections complete with bevel cut by angle grinder

including all breakages and making good the same. U clamps shall

be 10 mm thick, (Make: Jindal/ Bansal)

Painting with black anti-corrosive bitumastic paint of approved

brand and manufacture to give an even shade :

13.65.1 Two or more coats on new work Sqm. 307.16 140.25 43,079.35

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

Supplying & fixing Butterfly Valve (Wafer Type), PN-1.6 with S.G

Iron Disc Body S.G. Iron, Lever Operated, Nitrile/EPDM Rubber

62 N-DSR Lining. Seat Test Pressure 1.76 MPa (Hyd.) of the following size

complete with bolts, nuts, washers and inserted rubber gaskets as

Supplying & fixing Cast Iron Dual Plate (Wafer Type) Check Valve,

PN-16. With SS-304 Disc and Nitrile Rubber Lining. Shell Test

63 N-DSR Pressure - 24.5 Kg/cm2g, Seat Test Pressure 16 Kg/cm2g. of the

following size complete with bolts, nuts, washers and inserted

rubber gaskets as required

Supplying and fixing single headed stainless steel body hydrant

valve inlet complete with 63 mm dia female instantaneous outlet of

stainless steel conforming to type "A" of IS:5290-1977 with

butterfly lug, rubber blank cap, steel chain, adapter.

Supplying 63 mm dia 15 M long RRL hose pipe conforming to IS:636-

65 N-DSR 1962 Part- A, with stainless steel male & female coupling wire Nos. 38.00 7,294.00 277,172.00

wound copper wire with the pipe.(Make: Fireshield)

Supplying short stainless steel branch pipe IS marked with 20 mm

Supplying and fixing weather proof aluminium hose cabinet ( 0.75

M x 0.6 M x 0.25 M ) outdoor type made of 3 mm thick aluminium

sheet having central opening glazed door including necessary

locking arrangement, with powder coated finish and housing 2 Nos.

hose pipe, 1 No. branch pipe. The words "Hose Cabinet to be

painted on the Box. Box shall be fixed to wall.

Supplying and fixing Four Way Fire Brigade Inlet to Mains with

68 N-DSR Butterfly valve and dual plate spring operated wafer type non return Nos. 2.00 47,951.00 95,902.00

valve complete in all respects : (Make: Fireshield)

Providing and installing of 25 mm dia Air Release valve on Hydrant

69 N-DSR Line including 300 mm long 25 mm dia MS Heavy pipe and 25 mm Nos. 2.00 5,878.00 11,756.00

dia Ball Valve complete. (Make: Zoloto)

SUB-HEAD-6: TOTAL 12,800,000.00

SUB-HEAD-7: LANDSCAPING & HORTICULTURE

DSR-2020 HORTICULTURE AND LANDSCAPING

Trenching in ordinary soil up to a depth of 60 cm including removal

and stacking of serviceable materials and then disposing of surplus

soil, by spreading and neatly levelling sludge or / and manure

70 2.1 before and after flooding trench with water (excluding within a lead Cum. 750.00 78.10 58,575.00

of 50 m and making up the trenched area to proper levels by filling

with earth or earth mixed with cost of imported earth, sludge or

Supplying and stacking of good earth at site including royalty and

71 2.2 carriage upto 5 km lead complete (earth measured in stacks will be Cum. 300.00 515.60 154,680.00

reduced by 20% for payment)

Supplying and stacking sludge at site including royalty and carriage

72 2.3 upto 5 km lead complete (sludge measured in stacks will be reduced Cum. 300.00 294.00 88,200.00

by 8% for payment).

73 2.7 Fine dressing of the ground. Sqm. 1500.00 3.70 5,550.00

Mixing earth and sludge or manure in the required proportion

specified or directed by the Officer-in-charge

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to

60mm thickness of existing ground prepared with proper level and

ramming with tools wooden (Dhurmos) and than rolling the surface

with light roller make the surface smoothen and light waterning

with sprinkler and maintenance for 30 days or more till the grass

establish properly, as per direction of officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and

76 2.57 removal of unserveiceable material’s as per direction of officer in

charge (excluding cast of plant & water)

Digitally signed by SILKI

Name of Work: Firefighting, landscaping, STP, UGR and other misc. works for faculty

accommodation in Plot-A and Plot-B at IIT Kharagpur

BILL OF QUANTITIES

BRIEF DESCRIPTION OF WORK UNIT QTY RATE AMOUNT

2.57.3 Hedge Plant /Ground cover Each 80000 2.45 196,000.00

Half brick masonry with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in foundations and plinth in :

6.12.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum. 159.97 905.05 144,776.40

78 13.4 12 mm cement plaster of mix :

Out Door Gym Equipment

Supply & installation of Double Sky Walker i/c all fittings and civil

works complete in all respect

Supply & installation of Chest Press Double i/c all fittings and civil

works complete in all respect

Supply & installation of Shoulder Press Double i/c all fittings and civil

works complete in all respect

Supply & installation of Big Shoulder Wheel i/c all fittings and civil

works complete in all respect

Supply & installation of Double Air Walker i/c all fittings and civil

works complete in all respect

Supply & installation of Standing Triple Twister i/c all fittings and

civil works complete in all respect

Supply & installation of Leg Press i/c all fittings and civil works

complete in all respect

Supply & installation of FRP Bench i/c all fittings and civil works

complete in all respect

Supply & installation of Artifical Grass Seating i/c all fittings and

civil works complete in all respect

Supply & installation of Pull up Station i/c all fittings and civil works

complete in all respect

SUB-HEAD-7: TOTAL 2,700,000.00

Digitally signed by SILKI