Jumbukulam_2023

Amount

Earthwork excavation for foundation in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary, refilling the foundation with excavated earth and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of 2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers.

Earthwork Open excavation in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary refilling the foundation with excavated earth other than sandy soil in layers of not more than 15 cm thick layers well rammed and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of 2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers.

Refilling basement with excavated earth other than sand with an initial head lead of 100 mts. and depositing the earth as shonw by the departmental officers in layers of not more than 15cm thick well rammed, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers..

Supplying and filling in foundation and basement with Gravel in layers of not more than 15cm thick well rammed watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and Filling in foundation and basement with filling m sand in layers of not more than 15cm thick well rammed watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling of 40mm HBGS metal in dispersion trench around the stoneware pipe or in the leach pit or rain water harvesting pit or soak pit to the required thickness as directed by the departmental officers etc. complete. (The rate including cost of metal filling etc. complete complying with standard specification and as directed by the departmental officers..

Supplying and filling of 20mm HBGS metal in dispersion trench around the stoneware pipe or in the leach pit or rain water harvesting pit or soak pit to the required thickness as directed by the departmental officers etc. complete. (The rate including cost of metal filling etc. complete complying with standard specification and as directed by the departmental officers..

Cement concrete 1:5:10 (one cement, five M sand and ten aggregate) using 40mm gauge hard broken blue granite stone jelly for foundation and basement including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification and as directed by the departmental officers.

Providing Anti – termite treatment to soil adjacent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 part I to IV in stage to suit the progress of work consist as per the detailed specification as below (Measurements taken for the plinth area for the purpose of payment) including braking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport & storing etc., complete and as directed by the departmental officers.(The chemical should be got approved by Executive Engineer before use on work). Stage -1 : Spraying Anti –termite chemical solution for the foundation before laying concrete, in bottom and sides of foundation. Stage-2 : Spraying Anti –termite chemical solution to the grade beam level, spraying has to done for to grade beam brick masonry contact with the back fill earth. Stage-3 : Spraying Anti –termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out and sand filling by making holes with crow bar to a depth of 60cms and at 60cms intervals on both direction and at junction of wall and flooring throughout. Stage -4 : Spraying Anti –termite chemical solution alround building outside by making holes with crow bar before laying plinth protection and the holes to be close after the treatment.

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance using with IS:456-2000, 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of m sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

For foundation and basement

In Superstructure in Ground floor

In Superstructure in first floor

In Superstructure in second floor

In Superstructure in third floor

Supplying and Fixing RCC precast slab in reinforced cement concerete 1:2:4 (One of cement, two of sand and four of aggregate) using 20mm hard broken stone jelly and river sand, excluding the cost of reinforcement grills and including fabrication charges, moulding, curing, finishing charges and fixing in position neatly etc., complete complying with standard specification and as directed by the departmental officers.

50mm thick

75mm thick

Supplying, fabricating and placing inposition of steel reinforcement using MS/Ribbed tor steel rods for all RCC works as per the design given including cost of steel and G.I binding wire also in all floors etc., complete complying with standard specification and as directed by the departmental officers.. ( The contractor will have to make his own arrangement for the supply of M.S plain rod/ RTS rod and black binding wire )

Plain Cement concrete 1:2:4 (One cement two m-sand and four aggregate) using machine crushed 20mm gauge hard broken granite stone jelly excluding cenetering, shuttering and, but including laying, curing and finishing etc., complete complying with standard specification and as directed by the departmental officers.

For foundation and basement

For Superstructure in first floor

For Superstructure in second floor

For Superstructure in Third floor

Supplying and erecting steel centering including necessary supports for plain surfaces, for all RCC works including strutting upto 3.29m in all floors using mild steel shutters of size 90cmx60cm of BG 10 stiffened with mild steel angles of size 25mmx 25mmx3mm laid over silver oak (Country wood) Joists of size 10cmx6.5cm spaced at about 90cm c/c and supported by casurina props of 10cm to 13cm dia. (spaced at 75cm c/c) etc., complete complying with standard specification and as directed by the departmental officers. (The centering will be removed after specified period of concrete without damaging the concrete)

Column footing, plinth beam, grade beam, staircase stgep, bed block, etc.

For plain surface such as RCC floor slab, roof slab, beam litels bed blocks, landing slab, waist slabs and beams, etc.,

For plain surfaces such as RCC square or rectangular column, top and bottom slab of sunshade, boxing sill etc. complete as directed

For plain surface such as Vertical surfaces such as sunshade, boxing vertical drops, facia for sunshade and other vertical walls etc.,

For Curved surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall etc

Providing additional strutting using casurina poles to centering of RCC slabs or plane surfaces for every addtional 1 metre height or part there of but not less than 30cm over the initial height of 3m from floor level using casurina props of 10cm to 13cm dia including cross bracings etc., complete complying with standard specification and as directed by the departmental officer.

Brick work in cement mortar 1:6 (one cement and six Msand) using Fly Ash bricks of size 230×110×70mm including curing etc., complete complying with standard specification and as directed by the department officers. (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost).

For foundation and basement

For superstructure in ground floor

For superstructure in first floor

For superstructure in second floor

For superstructure in Third floor

Brick work in cement mortar 1:5 (one cement and five M sand) using Fly Ash bricks of size 230×110×70mm including curing etc., complete complying with standard specification and as directed by the department officers. (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost).

For foundation and basement

Damp proof Course with Cement Mortar 1:4 (One cement & four sand) 12mm thick mixed with water proofing compound of approved quality confirming to ISS @ 2% by weight of cement used etc complete complying with standard specification and as directed by the departmental officers.

Brick partion wall 11.10cm thick in cement mortar 1:3 (one cement and three M sand) using Fly Ash bricks of size 230×110×70mm including fixing hoop iron reinforcement if found necessary, laying, finishing and curing etc., complete complying with standard specification and as directed by the departmental officers.

For superstructure in ground floor

For superstructure in first floor

For superstructure in second floor

Supplying and Fixing New Cuddappah slab fine polished of approved quality of 38 / 40mm thick including cost of cuddappah slab for cupboards, transportation to work site, labour charge for forming grooves in masonry if necessary and laying the slab in position with cement mortar 1:3 (One cement and three m-sand) etc., complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing all reinforced cement concrete exposed surface such as reinforced cement concrete slab, sunshades, staircase steps landing slab with cement mortar 1:3 (One cement and three p sand) 10mm thick including hacking the surface and providing necessary cement mortar nosing beadings wherever necessary using the same mortar as directed by the Departmental Officers complete complying with standard specification.

Plastering with cement mortar 1:5 (one cement and five p-sand) 12mm thick in all floors using fine river sand including neat finishing, curing, etc., complete complying with standard specification and as directed by the department officers.

Plastering with cement mortar 1:3 (one cement and three p sand) 12mm thick with WPC 2% by weight of cement used in all floors using fine river sand including neat finishing, curing, etc., complete complying with standard specification and as directed by the department officers.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers..

Painting the walls two coats with best Oil bound distemper of approved quality (to be approved by the Executive Engineer before use on works) over one coat of primer for newly plastered wall including preparation of surface and finishing neatly including cost of all materials, brushes, scaffolding charges etc., complete complying with standard specification and as directed by the departmental officers.

Painting the exterior walls surface two coats of best and approved first quality and colour of Exterior emulsion paint in all floors over one coat of primer including preparation of surface, wall putty two coats with good quality including cost of wall putty , emmary sheet, plates, etc. and including labour charges for rubbing the wall scrapping putty pasting works and making good smooth surface and finishing neatly etc., . complying with standard specification and as directed by the departmental officers etc. complete. ( The make, quality and colour of paint should be got approved by the departmental officer before use of work)

Finishing the top roof with one course of solar reflecting ceramic tiles of size 305x305x7mm thick of approved quality set in cement mortar 1:3 (One cement and three sand) (12mm thick ) and mixed with for 10M2 / 4.00 kg Epoxy Packing conforming to ISS including curing etc., complete complying with standard specification and as directed by the Departmental officers.

Finishing the top of roof with combination mortar of ratio 1:1:6(one cement, one lime and six sand) 20mm thick using fine river sand in all floors wherever necessary including neat finishing, curing etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best approved of ISI quality of following dia PVC rain water down fall pipes having a working pressure of 4 kg / sq.cm including cost of necessary PVC shoe, PVC bend, C.I. gratings of required dia. and special clamps, brass screws, nails etc., and fixing of cast iron gratings at juction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable iron grating. The PVC pipe shall be fixed on wall with special type of clamps. Special type "U" clamp at the centre of the pipe line shall be fixed in addition to those for more than 3.0M pipe length complying with standard specification and as directed by the departmental officers..

160mm dia of PVC rain water down fall pipes (for three floors)

110mm dia of PVC rain water down fall pipes (for one floor)

Paving the floor with Stain free nano polished vitrified tiles (like Marbonite or equivalent) of approved quality and colour of size 600 x 600x 8 mm thickness in all floors over a base layer of cement mortar 1:3 (one cement and three M sand) 20mm thick and pointing with white cement using 0.30kg/m2 including adding suitable colour pigments to suit the colour of tiles finishing perfectly and curing etc., including cost of tiles, all materials and incidential charges, transportation charges and labour charges for laying tiles etc., complete complying with standard specification and as directed by the Departmental officers. (The tiles should be got approved by the Departmental officers before use on works).

Paving the floor with Tactile paver type of new tack BT yellow colour ceramic tiles of approved quality and colour of size 305 x 305 x 15mm in all floors over a base layer of cement mortar 1:3 (one cement and three M sand) 20mm thick and pointing with white cement using 0.30kg/m2 including adding suitable colour pigments to suit the colour of tiles finishing perfectly and curing etc., including cost of tiles, all materials and incidential charges, transportation charges and labour charges for laying tiles etc., complete complying with standard specification and as directed by the departmental officers . (The tiles should be got approved by the departmental officers before use on works).

Paving the floor with pre polished concrete Anti skid step tiles (like Eurocon Tiles) 20mm thick in all floors set in cement mortar 1:3 (One cement and three sand), 20mm thick and pointing with the cement including adding suitable colouring pigments of match with colour of tiles and finishing and curing as directed by the departmental officers including cost of tiles, and all other materials, transportation charges and labour charges for laying of tiles as directed by the departmental officers complete complying with standard specification. (The tiles should be got approved by the departmental officers before use on work.)

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 300 of 18 / 20mm thick of Jet Black and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality fine polished flamed steel grey Granite Slabs of size 1200 x 600 of 16 / 18mm thick and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Labour charges for finishing the top of working tables and staircase step portion with nosing arrangements in Granite slab tiles including cutting the edges and polishing including cost of polishing materials complete complying with standard specification and as directed by the departmental officers.

Labour charges for grooving the granite slab for staircase step portion including cutting the edges and polishing including cost of polishing materials etc. complete complying with standard specification and as directed by the departmental officers.

Paving the floor with colour design ceramic tiles of approved quality and colour of size 305 x 305 x 6mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand) 20mm thick and pointing with white cement using 0.30kg/m2 including adding suitable colour pigments to suit the colour of tiles finishing perfectly and curing etc., including cost of tiles, all materials and incidential charges, transportation charges and labour charges for laying tiles etc., complete complying with standard specification and as directed by the departmental officers . (The tiles should be got approved by the departmental officers before use on works).

Dadooing the walls with colour design glazed tiles of size 300mmx 450mmx 8mm of approved quality in all floors set in cement mortar 1:2 mix (one cement & two M-sand) 10mm thick and pointing with white cement using 0.4 kg/m2 including adding suitablee colour pigments to suit the colour of tiles including finishing the joints neatly and curing etc.,complete complying with standard specifications. (The tiles should be got approved by departmental officers before use on the work).

Supplying and fixing PVC beading of size 25x75mm with groove to sheet ceramic tiles at corner of wall function etc. for all tile works complete and complying with standard specification and as directed by the departmental officers.

Fabricating supplying and fixing in position CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames of section size 105mmx60mmx1.25mm thick with necessary rebate of size 35x15mm for housing door shutters conforming to IS specification. Frames shall be fabricated to the specified door size with joints properly welded and grinded. Stiffeners with 25x3mm MS flat shall be provided around the frame at 60cm intervals. The cost shall also include for providing 3 Nos. of MS clamps with 25x3 flats each on either sides of door frame, providing bottom tie, with 10mm dia MS rod, providing necessary holes for receiving tower bolts 2 Nos. with stiffeners on inner side, providing the required number of I.O hinges of size 125x30mm for shutters properly welded to the frames, finishing the door with one coat of good quality red oxide primer with cement concrete 1:2:4 (One cement, two sand and four aggregate) using 20mm gauge hard broken granite stone jelly packed inside to the frame including cost of all materials, fabrication and conveyance to the site and fixing in position with necessary scaffolding etc., complete complying with standard specification and as directed by the departmental officer.

Supplying and fixing in postion of 35mm thick solid core flush door shutters single leaf with following specification. with TW ply on both sides and with TW lipping of size 35x12mm on all edges with necessary adhesives and C.P. Screws Alu. Butt Hinges (6 nos. 250 x 16 mm Size) Alu. Aldrop1 No. 250 x 16 mm Size, Alu. Tower Bolt 2 No. 250 x12 mm size, alu. Tower Bolt 2 No. 200 x 12 mm size, D type alu. Handle 200mm length 2 No., alu. door stopper with rubber bush 2 No. shall be provided, complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in postion of 35mm thick solid core flush door shutters Double Leaves with following specification. with TW ply on both sides and with TW lipping of size 35x12mm on all edges with necessary adhesives and C.P. Screws Alu. Butt Hinges (6 nos. 250 x 16 mm Size) Alu. Aldrop1 No. 250 x 16 mm Size, Alu. Tower Bolt 2 No. 250 x12 mm size, alu. Tower Bolt 2 No. 200 x 12 mm size, D type alu. Handle 200mm length 2 No., alu. door stopper with rubber bush 2 No. shall be provided, complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supply and Fixing of M.S. steel doors with Single Leaves following specification. MS angles of size 40x40x 6mm at 3.5 kg/m used for the outer frame and MS angles of size 35x35x5mm at 2.60 kg/m for the shutter frames. Stiffners with 32x6mm at 1.50 Kg/m. MS flat is provided as the lock rail of the door and welded infact of both ends to the shutter frame, 18 gauge CR sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50 Kg / RM and MS flat on the rear side of the door sandwitching the CR sheet for rigidity with locking rail and bottom tie arrangements. Additional stiffners with 18x5 mm at 0.7 kg/m MS flats are provided horizontally diagonally on the rear side of the shutter. 2Nos of hinges in case of single leaf and 4Nos of hinges in case double leaf shutter is provided 6 Nos of hold fasts 200 length 40x40x6mm M.S. angle spliced at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. one at top and the other at bottom are provided. One aldrop is provided incase of double leaves door at lock rail section in the door. For single leaf doors, one more aldrop is provided in the inner side at the lock rail section of the door.

One rotating locking arrangements at the inner side of the door and additional provision for locking arrangements for lock is provided with 32x6mm MS flat on the rear side of the door at an appropriate place incase of a double leaves door MS flat 32x6mm at 1.50 kg/m is provided on the edge of one shutter to conceal the gap between the shutters. A tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation of fixing. All members are given a shop coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials labour charges transportation taxes and all other incidental charges etc., complete complying with standard specification and as directed by the departmental officers..

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter complete complying with standard specification and as directed by the departmental officers.. Solid panel PVC door with frame

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter complete complying with standard specification and as directed by the departmental officers. Supplying and fixing of PVC Sliding Door with Roller

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing MS grills to doors, windows and ventilators etc. using necessary MS flats (or) square rods for inner members and outer members which should be fixed to window frames as directed and design given by the departmental officers inclusive of cost of providing one coat of best quality red oxide primer etc., complete complying with standard specification and as directed by the departmental officers .

Supplying and fixing of special type Terra Cotta Jally of size 20x20x5cm of approved pattern including pointing neat finishing and labour charges for fixing the jally in position etc., complete complying with standard specification and as directed by the departmental officer.

Painting the new iron work with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat and including cost of painting materials, brushes, putty, preparation of surfaces and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officer. (The quality and colour of paint should be got approved by the departmental officer before use on work).

Painting the new wood work two coats with best approved first quality and colour of synthetic enamel paint over a priming coat of approved quality in all floors including cost of paint, labour and other materials like brushes, putty and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officers. (The make quality and colour of paint should be got approved by the departmental officer before use on work).

Manufacturing, Supplying and fixing Stainless Steel hand rail for staircase using 50mm dia 304L Grade stainless steel pipe of 1.60mm thick at at required locations to a height of 1000mm from finished floor level welded to 38.30 mm dia stainless steel pipe post of 1.00mm thick as vertical at 900 center with 3nos of 25.40mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100x100x6mm MS base plate encased in the base concrete. The rate is inclusive of charges for cutting , bending , welding , grinding polishing conveyance, electrical charges , etc., complete complying with standard specification and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for toilets of Differentially abled person using 50.80mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete complying with standard specification and as directed by the departmental officers.

Providing expansion joint of 20mm width in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non - absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed by the departmental officers..

Providing expansion joint of RCC floor slab for 20mm width using polysulphide as sealent on top and bottom for a depth of 7.5mm each and packing the inner space using compressible non - absorbent, filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed by the departmental officers..

Providing expansion joint of 20mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non - absorbent, flexible and well compressible filler materials of approved quality and covering top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed by the departmental officers..

Providing mixing laying polymer based water proofing treatment for the sunkan toilet by applying cement based fiexable WPC conforming to IS 2645 to a thickness of 1mm of the prepared surface of the roof slab / floor slab as per specification mendioned above providing cm 1:3 water proofing cover plaster to a thickness 12mm. The malaime coating with admixture of approved make rate quoted is inclusive of preparation of surface which including cleaning of surface polymer morter, curing, labour, tools equipments etc., rate inclusive of cement and sand required for the treatment the coat and labour charges for fixing 25mm dia pressure pipe 15 kg / m2 to length of 45 cm for drip pipe etc., complete complying with standard specification and as directed by the departmental officers..

Brick Jelly Lime Concrete of 1:2:5 (One Lime,Two m Sand and Five Brick jelly ) with 40 mm hand broken brick jelly for Sunken portions including dewatering wherever necessary and laid in layers of not more than 15cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.

Supplying and fixing in position of Cast Iron Man hole cover with CI frames of size 600x600mm (Heavy Duty) of best approved quality and as per Indian standard specification make etc., complete complying with standard specification and as directed by the departmental officers. (The Cast Iron Man hole cover should be got approved by the departmental officers before use on work).

Supplying and fixing PVC Ventilating shaft of 110mm dia (having working pressure 4 kg / sq.cm) and 3 m height including cost of cylindrical cowl of best approved quality etc., complete complying with standard specification and as directed by the departmental officers. The PVC ventilating shaft should be got approved by the departmental officers before use on work.

Supplying and fixing of 300mm RCC hume pipe of flush joint to RCC wall with 25mm thick to a length of 30cm in RCC M 35 with nominal special reinforcement as directed by the departmental officers etc., complete complying with standard specification and as directed by the departmental officers..

Supplying and installation of Ceramic Steel chalk writing board with the following specification. The 2mm GI Sheet is placed with wall side over the GI sheet necessary adhesive is spreaded and fixed the 9mm MDF board on the GI sheet 0.40mm thick ceramic steel chalk board is provided over the MDF board and the whole arrangements are fixed to the frame using heavy anodized Aluminium section and Chromium plated provided in the corners. The whole arrangement are fixed to the wall using wooden plugs and screws etc., The rate includes all above materials, labour charges and taxes etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing ornamental Brass-in-lay Burma Teak Wood Entrance Door with a size of2.10m x 2.55m with six leaves as per the drawing and design as approved by the departmental officers. The clear opening of each door shall be of 2.00m. The outer frames are of finished size 175mm x 125mm.The Each door shall have two leaves of 1/3 paneled and 2/3 glazed. The Outer frame of the shutter of finished size of 150mm x 50mm.All the Panels shall be of finished 50mm thick. The main outer frame, shutter frame and panels shall be engraved with computer design ornamental carving works of approved pattern with skilled carpenter as directed by departmental officers. All the glazing works shall be done with design painting works. Necessary grill protection arrangements shall be made for the glass portion. The door frame and shutters shall given two coats of best and approved quality of high Glossy Polyurethane finish. The rate includes cost of best and approved quality of Burma Teak wood, design painted glass, Brass hinges, Tower bolts, Aldrop, locking arrangments, ornamental handles, brass screws and labour charges, transportation charges, all taxes, etc., complete complying with standard specification and as directed by the departmental officers..

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) powder type fire extinguisher of 6 kg capacity as per IS:15683with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc. including conveyance, all incidential charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc. complete as per standard specification and as directed by the Departmental Officers. Make: Excellent/Safety First/equivalent.

Supply and fixing of carbon-di-oxide gas type 2 kg. capacity Fire extinguisher as per new IS:15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc. including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc. complete as per standard specification and as directed by the Departmental Officers. Make: Excellent/Safety First/equivalent.

Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels,spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and laying of 63 mm thick high strength type of interlocking rubber moulded hydraulic pressed paver block of approved colour made up of designed concrete mix 1:1:2 using 10 to 12mm size HBG stone jelly in required shapes and sizes having minimum compressive strength of 40 N/mm2 to be laid in flurrying bone pattern with approved non sticking surface at top. The rate is inclusive of levelling the site, compacting with power compactor and sweeping the sand grouting and also inclusive of transportation charges, loading, unloading and labour charges for laying the paver block, etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and laying of 83 mm thick high strength type of interlocking rubber moulded hydraulic pressed paver block of approved colour made up of designed concrete mix 1:1:2 using 10 to 12mm size HBG stone jelly in required shapes and sizes having minimum compressive strength of 40 N/mm2 to be laid in flurrying bone pattern with approved non sticking surface at top. The rate is inclusive of levelling the site, compacting with power compactor and sweeping the sand grouting and also inclusive of transportation charges, loading, unloading and labour charges for laying the paver block, etc. complete complying with standard specification and as directed by the departmental officers.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and complete complying with standard specification and as directed by the departmental officers.

Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick bothside prelaminated partile board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section-Vertical &Top rail: 50x44.45x2.50mm @ 1.292 kg/m and Bottom rail : 100 x 44.45 x 2.50mm @ 1.974 kg /m , Lock rail : 50x44.45x2.5mm @ 1.292 kg/m,Alu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/m Alu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 2 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 2Nos ., lock-1No., Door stopper with rubber bush including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition afterfixing etc. complete. All the Alu. sections are to be anodised with matt finish under electically contolled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Drilling 150mm dia vertical bore well to the required depth as directed by the departmental officers including labour charges inserting pipes assembly in the drilled pit including welding the joints wherever necessary and grouting the casing pipe if necessary in overburden soil etc. complete and including transportation charges for the rigs and supporting vehicles from one place to another etc. complete as directed by the Executive Engineer without casing pipe,.

Drilling 150mm dia vertical bore well to the required depth as directed by the departmental officers including labour charges inserting pipes assembly in the drilled pit including welding the joints wherever necessary and grouting the casing pipe if necessary in hard rock etc. complete and including transportation charges for the rigs and supporting vehicles from one place to another etc. complete as directed by the Executive Engineer.

Supply of 160mm PVC special blue slotted casing pipe of best approved quality having pressure of 6 kg/sq.cm. etc. complete as directed by the departmental officers. The pipe should be got approved by the Executive Engineer before use on works.

Supply of suitable 160mm dia PVC End cap of best approved quality having pressure of 6 kg/sq.cm. etc. complete as directed by the departmental officers. The pipe should be got approved by the Executive Engineer before use on works.

Suppling and delivert of best and approved quality of 40mm dia HDPE pipe of 10kg/m2 size including laying in the basement and tying with copper wire etc., complete complying with standard specification for delivery line from the bore from submersible pump in borewell complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of MS borewell clamp suitable for 40mm dia HDPE pipe and 4 Nos. of 5/8" bolts and nuts of best approved quality etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting 3 phase multi stage 5.00 H.P.Submersible pump set of approved make conforming to ISI.including cost of all accessories, transportation charges etc.., as directed by the Departmental Officers complete complying with standard specification. The quality and standard of product should be got approved by the Departmental Officers before erecting. Necessary warranty card should be produced before erection of Motor complete complying with standard specification and as directed by the departmental officers..

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days complete complying with standard specification and as directed by the departmental officers..

Supplying, fixing of panel board of 3 phase submerssible pump size having 1 No. 30 Amps TPIC switch, 1 No. of DOL Starter, 1 No. Ammeter 0 to 30 Amps with rotary switch 1 No. of Volmeter 0 to 500 volts with all accessories etc., complete as directed by the departmental officers

Supplying and tying of Nylon rope of 18mm dia thread make with best quality for holding submersible pump etc., complete as directed by the Executive Engineer. The Rope should be got approved by the Executive Engineer before use on works.

Supplying and fixing of 3 x 4 sq.mm PVC insulated and sheated 3 core flat type copper cable confirming to IS 694/1990 etc., complete complying with standard specifications and as directed by the departmental officers..

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) with necessary earth work anf refilling charges the earthwork and refilling charges shoul be paid seperatly, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. For External Water supply arrangements. (Below Ground Level) 50mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs,UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. For External Water supply arrangements. (Above Ground Level)

40mm dia UPVC pipe

32 mm dia UPVC pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs,UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. For Internal Water supply arrangements. (Above Ground Level)

25mm dia UPVC pipe

20 mm dia UPVC pipe

Supplying and fixing in position of the following UPVC specials best approved quality conforming to ISS and providing leak proof joints with UPVC adhesive etc., including fixing to walls with necessary teak wood plugs screws etc., and giving connections to the UPVC pipe dismantling the brick masonry RCC floor or roof slab and redoing the disturbed portion to original conditions etc., complete complying with standard specifications. -The UPVC specials should be got approved from the Executive Engineer before use on works -.

50mm dia UPVC union

40mm dia UPVC union

32mm dia UPVC union

25mm dia UPVC union

50mm dia UPVC Elbow

40mm dia UPVC Elbow

32mm dia UPVC Elbow

25mm dia UPVC Elbow

40mm dia UPVC hex nipple

32mm dia UPVC hex nipple

25mm dia UPVC hex nipple

25x20mm UPVC Reducer Elbow

20x15mm UPVC Reducer Elbow

40mm dia UPVC Tee

32mm dia UPVC Tee

25mm dia UPVC Tee

25x20mm UPVC ReducerTee

20x15mm UPVC Reducer Tee

Supplying and fixing in position first quality and approved variety of Gun metal Gate/Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

50 mm dia G.M Gate valve

40 mm dia G.M Gate valve

32 mm dia G.M wheel valve

25 mm dia G.M wheel valve

Supplying and fixing in position 15mm dia Chromium Plated brass screw down tap (heavy type) of approved make conforming to ISS.and including cost of shellac, thread complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Departmental Officers before use on the work)

Supplying and Fixing of PVC ready made water tank of approved quality with standard specification and best brand including testing for leakages after making installations and connections. The cost inclusive of lid and lock with bolt and nuts for PVC tank, transportation, loading, unloading, lifting, installation and necessary connections etc., complete complying with standard specifications and as directed by the departmental officers.(The PVC Water Tank should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Indian water closet oriya type of size 580x440mm white glazed earthernware of approved quality with 'P" trap or 'S' trap conforming to IS 2556-Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to PVC. pipes by dismantling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specification and as directed by the departmental officers.(The Oriya type Water Closet and all accessories should be got approved by the departmental officers before use on work)

Supplying and fixing in position White Glazed European water closet of best quality and approved make with 100mm P or S trap with double flapped rigid PVC.seat cover with chromium plate brass hinges, including supplying and fixing PVC. Low level flushing tank 10 litre capacity of approved quality on wall with teak wood plugs, brass screws and 2 numbers 15mm dia gun metal wheel valve, 15mm dia nylon connection and giving necessary water supply connection as directed by the departmental officers. The rate includes cost of 100mm dia PVC.Pipe 60cm long including cost of 3 Kg.of white cement 6Kg.of cement, spunyarn, shellac, thread ball, teak wood plugs, brass screws 75mmx10mm etc., complete complying with standard specification and as directed by the departmental officers. (The European Water Closet and flushing tank should be got approved by the Departmental Officers before use on work.)

Supplying and fixing Stainless steel health faucet of best quality with control valve etc., complete complying with standard specification and as directed by the departmental officers (The materials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position of Indian make white glazed earthen ware lipped mouth flat back Urinal of best approved quality with 32mm dia bell mouthed PVC connection,15mm dia G.M wheel valve,fixing the Urinal to the wall in position with necessary T.W. plugs,clamps,screws shellac etc.,including dismantling masonry if necessary and redoing the same to original condition,fixing the 15mm GI pipe connection and wheel valve, painting the pipe with two coats and checked without any leakage etc., complete complying with standard specification and as directed by the departmental officers.(The urinal should be got approved by the departmental officers before use on work)

Supplying and fixing in position of polished white marble slab (Adanga) of 20mm thick for urinal partition of size 1.20x0.60m including and fixing the marble slab with C.M.1:3 etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best quality of approved make white glazed earthernware wash hand basin (without pedestal) of size 550x400mm with a pair of cast iron brackets , including cost of 15mm diametre brass chromium plated pillar tap, 32mm diametre C.P.waste, 32mm diametre PVC waste pipe with rubber plug and chain, 15mm diametre gun metal wheel valve, 15mm dia brass nipple, 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with pair of C.I.brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anti-corrosive paint including testing for leakage etc., complete complying with standard specification and as directed by the departmental officers.(The wash hand basin and specials should be got approved by the departmental officers before use on work)

Supplying and Fixing of white Porcelain sink of size 600mm X 450mm X 200mm including cost of 32mm dia 'B' class GI waste water pipe with rubber, plug and chain and 32mm dia CP waste coupling, 15mm dia brass nipple including fixing the sink in position and testing for leakage etc., complete complying with standard specification and as directed by the departmental officers. (The sink and specials should be got approved by the Executive Engineer before use on works). (For fixing the sink on masonry support walls to be measured and paid in main item.)

Supplying and fixing in position of SS swan neck Tap of approved make confirming to ISS and including cost of shellac, thread etc. complete complying with standard specification and including cutting and threading wherever necessary etc. complete and as directed by the departmental officers..

Supplying and fixing of 160mm UPVC pipes of approved quality and good variety including fixing charges, cutting and threading of pipes in below ground level for both internal and external water supply arrangements etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position PVC Nahini trap of size 100x75mm with best pvc gratings of approved brand and quality with fixed over a bed of brick jelly lime concrete 1:2:5(one part of lime,two parts of sand and five parts of 40mm size brick jelly)and finished with cement Mortar 1:3(one cement and three sand)including dismantling masonry works wherever found necessary and making good the damaged portions to the original condition giving connections to the pipe etc., complete complying with standard specification and as directed by the departmental officers. (The PVC Nahini trap with grating should be got approved by the departmental officer before use on works).

Supplying, laying and jointing PVC soil / waste pipes of approved and best variety conforming to IS. Specification with ISI. mark of the following sizes including, cutting and threading of PVC Pipes, fixing specials but excluding cost of such specials but including fixing to wall with necessary teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in roof and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges. The PVC Pipes should be got approved by the Departmental Officers before use on work. Below ground level.

75mm dia PVC soil pipe

110mm dia PVC soil pipe

160mm dia PVC soil pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia PVC door Tee

110mm dia PVC Door "Y"

75mm dia PVC door Elbow

75mm dia PVC plain Bend

PVC Cowl 110mm dia

PVC Cowl 75 mm dia

Supplying and fixing of Incinerator for Ladies Toilet etc., complete complying with standard specification and as directed by the departmental officers.

Supplying laying and fixing in position of following LPG GAS pipe line and specials with ISI Standards including labour for fixing the specials in the gas pipe line by gas welding and using the joints with tuflan tape paste in every joints and leakage test, painting with red colour, clamping on ceiling with necessary hanging arrangements etc. complete complying with standard specification and as directed by the departmental officers.

4x1 manifold F type

manifold F type

manifold clamp

1/2" x1/2" Non return valve

1/2" x1/2" Suraksha hose

1/2" x1/2" Sierra type adopter

1/2" x1/2" Copper pigtall

15 PSI high pressure regulator

11 PSI high pressure regulator

1/2" x1/2" Ball valve

1/2" x1/2" HP adapter (Brass)

1/4" x1/2" HP adapter (Brass)

1/2" x1/2" main line valve

Bunsen Burner (Heavy)

Bunsen Burner (Tap & cock)

Suraksha Hose

Four way terminal

Terminal plate

Pinset No.203

Pinset No.275

Pinset No.276

MS pipe clamp 1/2"

MS socket

MS pipe for ERWC Tata make of C class pipe 15mm dia etc complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting 3 phase multi stage 3.00 H.P.Submersible pump set of approved make conforming to ISI.including cost of all accessories, transportation charges etc.., as directed by the Departmental Officers complete complying with standard specification. The quality and standard of product should be got approved by the Departmental Officers before erecting. Necessary warranty card should be produced before erection of Motor complete complying with standard specification and as directed by the departmental officers..

Providing cupboard shutter using termite/water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc. as directed by the departmental officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer before use on work.

Supplying and fixing of Hylem sheet 3mm thick for expansion joint etc., complete complying with standard specification and as directed by the Departmental officers

Finishing the top of flooring with granolithic floor finish of 25mm thickness with plain cement concrete of mix 1:2:4 (One cement, two M sand and four aggregate) using 20mm / 10 to 12mm ISS gauge hard broken granite stone including finishing the top smooth and forming thread lining and curing etc., complete complying with standard specification and as directed by the Departmental officers

Sub Total

vm.constructions