CA NO GE(H)-17/2024-25 SPECIAL REPAIR TO SEWAGE LINE AND OTHER SANCTIONED WORK IN THE AOR OF AGE B/R-I UNDER GE HISAR AT HISAR MIL STN

Amount

Excavation in trenches not exceeding 1.5 m wide and not exc. 1.5 m depth for laying cables, foundation for pole etc and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n exc 25 cm thick etc complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point etc complete all as specified and directe.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Surface dressing not exceeding 15 cm depth and getting out in soft /loose soil including clearing away all grass and vegetation saplings , shrubs , bushes , undergrowth roots and removing rubbish upto a distance n exc 50 mtrs outside the periphery of the any installation/ feeder pillar area etc. Note:-The contractor will ensure that no vegetation grows during the contract period on the area so dressed.

Demolition and breaking up drain pipes 150mm bore (Salt glazed stone ware, AC or Reinforced concrete) set in cement mortar and removing demolized materials out side Mil Stn area complete all as specified.

All as per srl item No. 08.00 here in before but 200mm bore

All as per srl item No. 08.00 here in before but 300mm bore

Dismantling of cast iron pipes of any size of bore as in soil, waste or vent pipe including removal of cement joint fixed to wall or laid in floor complete all as specified and directed .

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

Material and labour for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/RCC drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

All as per srl item No. 13.00 here in before but 200mm bore

All as per srl item No. 13.00 here in before but 300mm bore

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

All as per srl item No. 16.00 here in before but 200mm bore

All as per srl item No. 16.00 here in before but 300mm bore

M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified.

M&L for PCC 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in coping, hold fast, bed block and similar works as directed, complete, all as specified.

M&L formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete all as specified and directed.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 5cm but n exc 10cm wide for rough finished flat surfaces of concrete all as specified and directed.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

M & L for rendering 15mm thick in cement mortar 1:3 on faces of brick work or concrete surfaces of walls, finished even and fair including mixed with and including liquid water proofing compound @200 ML per 50 KG by weight of cement complete all as specified and directed.Note:- (WPC shall be measured & paid separately under respective item)

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and fair complete all as specified.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete .

Supply only water proofing compound (ISI marked).

S&F in repair factory made (SFRC) precasted reinforced cement concrete round manhole cover as required thickness not less than 100mm for heavy duty and dia of manhole cover not less than 630mm, edge of manhole cover locked with 1mm thick MS sheet complete all as specified and directed.

S&F in repair factory made (SFRC) precasted reinforced cement concrete round manhole cover as required thickness not less than 50mm of size 700mm x 550mm, edge of manhole cover to be locked with 1mm thick MS sheet complete all as specified and directed.

S&F in repair factory made (SFRC) precasted reinforced cement concrete round manhole cover as required thickness not less than 50mm of size 350mm x 350mm, edge of manhole cover to be locked with 1mm thick MS sheet complete all as specified and directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

M&L for cutting into existing manholes/Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.

Cleanning of sewer lines of 150mm bore by mannually or mechanically including uses of water jet or supper succer machines if required at site and disposing sludge out side mil stn area complete all as specified and directed by Engineer in charge.

All as per srl item No. 38.00 here in before but 200mm bore

All as per srl item No. 38.00 here in before but 300mm bore

Cleaning of manholes of depth varying from 0.60M to 3.0M, Septic tanks, sludge chambers by mannualy or by mechanically including uses of jet machines / supper succer machine and dispossing sludge out side Mil Stn area complete all as specified and directed by Engineer in charge.

M&L mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Gde E-165 (Fe 290) all as specified and directed.

S&F 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed on wall necessary fittings / connection & MS clamps / clip and necessary screwing as required in new or old position complete all as specified and directed

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls all as specified & as directed..

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint on walls over a coat of primer all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts and including Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified. complete all as specified & directed. Note :- Any gap between pre-painted galvalume aluminium zinc coating sheet and brick wall, if occurs after the fixing of sheet shall be filled by CM 1:3 morter and wall surface shall be make good as per existing surface

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F rolled mild steel work as in Plates (plain or chequered) channels, Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.

S&F mild steel framed work as in steel frames, chowkats, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

M&L for 100mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 75mm thick PCC 1:2:4 type B2 using 40mm graded crushed stone aggregate as in flooring as directed) all as specified and as directed.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long, dia of neck not exc 20mm and not exc 25mm complete all as specified & as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm bot not exc 10cm long and dia of neck not less than 10mm complete all as specified.

S&F plain angle cleats for securing purlins to trusses or rafters and similar articles conforming to Fe-290 Gde E-165 complete all as specified.

S&F for cutting existing roads for replacement of sewer pipelines complete all as specified and directed at site by Engr-in-Charge. Note : (i) Depth of cutting shall be from top of block toping of road to bottom of soling layer of road & will be considered as soft/disintergated rocks. (ii) Earth below soling layer shall treated as soft soils & shall be measured and paid in item No 1.00.

moti construction company (BID ID -3041884)

malik constructions (BID ID -3036533)

B B BUILDERS (BID ID -3047694)

M/S RAJINDER SINGH (BID ID -3042515)

VIKAS INFRASTRUCTURE (BID ID -3042327)