SPL REPAIR TO BLDG NO P-53 PROVN OF BOUNDARY WALL WITH AREA DRAINAGE OF 71 MBSC 01 x TOILET BLOCK WITH URINAL AND BATHING FACILITY NEAR BLDG NO P-84 AT 11 GRRC AND TOILET BLOCK NEAR BLDG NO T-76 CAMPBELL LINE UNDER GE (WEST) LUCKNOW

Amount

Excavation in trenches n exc 1.5 m wide and not exc 1.5 m deep and getting out in soft/ loose soil complete all as specified and directed.

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundation, filling and mass concrete complete all as specified and directed.

M&L Brick work with fly ash Brick straight or curve on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M & L for Brick Work with flyash old size brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Returning filling in including spreading leveling watering and well ramming in layers not exc 25 cm in soil complete all as specified and directed.

Removing excavated materials to a distance n exc 50 mtr and deposited where directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and direced.

M&L for rendering 15 mm thick in CM 1:4 with water proofing compund (@ 3% by weight of cement) on fair faces of brick work or concrete surface and finishing the surface even and smooth without using extra cement all as specified and directed. Note:- Water proofing compund shall be measured and paid seprately.

M & L for 20mm thick bearing plaster in cement mortar 1:4 using water proofing compound @ 3% by weight of cement and complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

M & L for sand filling/cushioning under floors or in foundation including watering and consolidation or under UG cables (8cm deep before laying of cable and 15cm deep over the cable as applicable) etc. complete all as specified and directed.

M & L for rendering 10mm thick in CM 1:3 on fair faces of brickwork or concrete surface as in ceiling and finishing the surface even and smooth without using extra cement as on ceiling complete all as specified and directed.

M & L for form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work n. exc 200mm thick (horizontal or sloping), for flat rough finished surface of concrete complete all as specified and direted.

M & L for RCC (M-25) design mix as in slab supported on wall, beam and columns in floors, roofs, landing, balconies, seck slabs and in shelves complete all as specified and directed.

M & L for plastering 10mm thick in CM 1:3 using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions finishing the surface even and smooth without using extra cement complete all as specified and directed.

S&F 10mm dia and over TMT bar, cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

S&F for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers, and binders, cut to length, bent to shape required including including cranking bending spirally for hooping fpr columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 (20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps, and other similar bands, plinth courses, string courses, lacing courses, parapets and railings, copings, kneelers, apex stone, bed plates, water troughs and the like including weathering slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M & L for preparation of new surfaces of wall and applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L for preparation of new surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for hardcore of broken stone or boulders of gauge n.exc 63mm deposited spread and levelled in layers n .exc 15cm thick watered and rammed to a true surface complete all as specified and directed.

M & L for 75mm thick cement concrete (1:4:8) type D2 using (40mm graded stone aggregate) as in sub base complete all as specified and directed.

M & L for 15mm dia GI tubing medium grade galvanised with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M & L for 20mm dia GI tubing medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M & L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but n.exceeding 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layers of mortar for laying floor finishes with CM (1:6) complete all as specified and directed.

M & L for coloured glazed ceramic tiles 600x450x7mm/300 x 450 x 7mm thick as on vertical surfaces such as skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified and directed.

S & F CP Bib taps 15mm fancy type Chromium plated cast copper alloy with crutch or butterfly handle screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F CP shower rose with or without swivel joints any size including fixing to steel pipes or union complete all as specified and directed

S & F CP soap dish fixed wall with chromium plated brass screw complete all as specified and directed.

S & F WHB vitreous China white flat back size 550 x 400mm incl brackets, waste coupling and waste pipe including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S & F 15mm bore pillar taps fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered HOT or COLD with long screwed shanks and flynuts, screwed for iron pipe and fixed complete all as specified and directed.

S & F 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float and handle including brackets complete all as specified and directed.

S & F CP stop/angle valves 15mm bore fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F for PVC connection pipe 15mm bore 450mm long complete all as specified and directed.

S & F for rotational moulded double layered polyethylene water storage tank cylindrical hoisted & fixed in position all as specified capacity 500 ltrs complete all as specified and directed.

S & F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball & fixed complete all as specified and directed.

S & F vitreous china squatting pan Orissa patern long pan size 580 x 440mm with CI trap long neck 100mm with integral foot rest & fixing including making good floor to match complete all as specified and directed.

S & F steel chromium plated urinal spreader suitable for bowl type urinal complete all as specified and directed.

S & F vitreous china bowl type urinal flat back, size of 465x355x265 mm/355x345x535mm white with grating and union for discharge pipe excluding flushing cistern, flush pipe and waste pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar 1:4 complete all as specified and as directed.

S & F framed work such as grills, gratings etc with ends of bars shouldered and / or reveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framed work of water tanks and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed.

S & F steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

M & L for PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in bed blocks for hold fasts etc complete all as specified and directed.

M & L for 3mm thick figured glass pin headed type incl glazing with putty in squares area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S & F solid PVC door frame of size 50 x 47mm made out of 5mm thick plain coloured PVC sheet reinforced with MS square tube etc complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting frame made out of MS tube for top and bottom rail MS frame shall be covered with heat mould plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for style and plain colour PVC sheet for top rail lock and bottom rail on either side and as gap insert for top rail and bottom rail plain colour PVC sheet tape fixed i n MS frame welding sealed to the style and rail with suitable PVC sheet bearing and jointing together with solvent cement etc complete all as specified and directed.

S & F 300mm long aluminium alloy, sliding door bolt with hasp & staple(bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed.

S & F 150mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete all as specifed and directed.

S & F for aluminium anodized barrel tower bolts 200mm/150mm of extruded section and fixed complete all as specifed and directed.

S & F stainless steel butt hinges 100mm medium weight and fixed complete all as specifed and directed.

S & F Gun metal, globe or gate valves 20mm with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 type C-2 using 40mm stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

S & F glass corner self fancy type 250x250 and 10mm thick fixed it with brass bracket and screwed complete all as specified and directed.

S & F sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F CP brass (tabular towel rail) 20mm dia D type aluminium anodised, 60cm long between flange complete all as specified and directed.

S & F 100mm bore CI sand cast soil waste and vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed.

S & F cast iron bends (any radius) diminishing pieces or tapers for 100mm dia complete all as specified and directed.

S & F 75mm bore CI sand cast soil waste and vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed.

S & F 75mm bore CI tee single (equal or unequal), ordinary or inverted (spigot or socketed type)or with parellel branches complete all as specified and as directed.

S & F cast iron bends (any radius) diminishing pieces or tapers for 75mm dia complete all as specified and directed.

S & F 75mm bore CI sand cast soil waste and vent pipe in any length with or without ears with cement joints fixed to walls complete all as specified and directed.

S & F 75mm dia cast iron cowl complete all as specified and directed.

M & L for cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1(1:2:4) for 75mm dia of outlet complete all as specified and directed.

M & L for providing precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slab for man holes shelves and similar articles etc set in CM 1:4 incl necessary form work complete all as specified and directed.

M & L for 150mm dia salt glazed stone ware drain pipes laid in trenches and jointed as specified complete all as specified and directed.

M & L for concrete bed to drain pipes PCC 1:4:8 type D-2 (40mm graded stone aggregate) including packing under and haunching against the sides of pipe after they are laid and tested for 150mm dia complete all as specified and directed

M & L for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in benching and coping complete all as specified and directed.

M&L for construction of septic tank for 25 users capacity, including excavation and earth work in ordinary soil, foundation with PCC 1:2:4, type B-1, brickwork in CM 1:4, RCC 1:2:4 type B-1 slab, RCC precast manhole cover having 6mm plate embedded around with angle iron frame, vent shaft and sludge chambers etc all as shown on drawing no. TD/687 sheet 1/1 & 2/2

M & L for Construction of Soakage well 1.2m inner dia and 4.5m effective depth including excavation in any type of soil, foundation in PCC 1:3:6 walls of honeycombed masonary with top ring of RCC 1:2:4 type B-1 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab, interconnecting pipes complete filled with brick bats complete all as shown on drawing No. TD/576 sheet 1/1 & 2/2.

M & L for 75 mm thick PCC 1:4:8, type D2( using 40mm graded stone aggrtegate) as in sub base etc complete all as specified and directed.

M&L for machine pressed precast concrete interlocking pavor block of 60 mm thick (M-35 Grade) of any shape and size confirming to IS-15658-2006 as in hard standing with grey cement and pigment complete all as specified and directed.

M & L for Modular brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 Incl Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles. all as specified and directed.

M & L for cutting grooves in brick wall, 75 mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M & L for PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges of any thichness etc. complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement Incl Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. incl mouldings, chamfers, splay srounded or coved angles, beads, grooves and rebate upto 10 cm in width or 15 cm in girth including taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water complete all as specified and directed. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade over a coat of chalk whiting complete all as specified and directed.

M&L for preparation of Old plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying one coats of cement base paint complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.incl brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors joints free, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 incl Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 600x450x7mm/ 300x600 x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4 incl Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed.

Material and labour (Ist Quality) vitrified tiles,double charged, 10mm thick, light shade, square polished, area of each tiles n. exc 0.36 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Material and Labour (Ist Quality) vitrified tiles, 10mm thick, light shade, square polished, area of each tiles n. exc 0.36 sqm as in skirting etc, set and jointed in neat cement paste and pointed in white or coloured cement to match including 10mm thick backing coat in CM 1:4 ccomplete all as specified and directed.

M&L Marble tiles 30cmx20cm x20mm thick machine cut, bedded jointed and pointed with grey cement slurry and laid over 20 mm thick screed bedding layer in CM 1:6 including cutting,grinding and polishing complete all as specified and directed.

M & L Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete 15mm thick screed bed in CM 1:4 including cutting, polishing & rubbing and including rounding of exposed edges incl Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and direceted.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M & L for drilling through holes in granite stone for pipes etc not exc. 25 mm dia complete all as specified and directed.

S & F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified anddirected.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even without using etra cement incl Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls.

M & L for GI tubing 15mm dia, medium grade, galvanised with all fittings fixed to wall,trenches and floor incl Taking up or down steel water tubing and connections all as specified.

M & L for GI tubing 20mm dia, medium grade, galvanised with all fittings fixed to wall,trenches and floor incl Taking up or down steel water tubing and connections complete all as specified and directed.

S&F in repair vitrious China squatting pan orissa pattern size 580x440mm white with P or S trap and making good floor complete all as specified and directed.

S&F in repair PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair PTMT grating 125mm dia without waste hole (Minimium weight 40 grams) complete all as specified and directed.

S&F in repair PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides complete all as specified and directed.

S&F in repair long body 15mm bore bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair CP angle valve long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type complete all as specified and directed.

Supply and fixed in repair stop valves, 15mm dia, cast copper alloy,CP fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor complete all as specified and directed.

S&F in repair PVC(SWR) 75 mm bore floor trap plan with grating including jointing with solvant cement complete all as specified & as directed.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. incl dismantling PVC water tanks and removing for capacity exceeding 500 litres & not exceeding 1000 litres etc., all as directed.

Supply & Fixing in repair gun metal gate valve screwed both ends to15mm bore pipe complete all as specified and directed.

Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm/75mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L in repair PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of frame size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant complete all as specified and directed

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face)& 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engr-In-Charge.(Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F 35 mm thick factory made wire mesh solid WPC pre laminated both side door shutter consisting of density 650 kg/cbm manufactured by an ISO-9001-2015certify company, Door to be panelled with ss mosquito mesh and XTN aluminium mesh for additional strength and safety purpose. (conforming as per S:4020). The door should be water proof, termite proof,fire retradant and having screw holding capacity. Door to be fixed to framewirh 3 nos MS Powder coated butt hinges size 100 mm*25 mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the MS tube. other hardwares should be fixed with 19*6 mm size steel screws etc complete all as specified and directed

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Supply and Fixing Steel Box type Windows/Ventilators with both provisions ie glazed and gauzed double panel / single panel shutters, Gaused shutter shall be fixed in inner side and glazed shutter shall be fixed at outerside of the frame. The section of outer frame shall be 60 x 45 mm, F/S mullion/ transum 60x30x25 mm, F/S shutter frame 50x35x20mm, with handle and stopper of Z sec of size 20 x 25x 20mm The section shall be made of ERW Section of 16 Gause. 02 Nos of Box type hinges 75 mm long 12 mm dia with one part of hinges spot welded with frame and other with shutter for each openable shutter. 04 Nos of flat iron fast shall be welded with each window. 100 mm long handle and 150 mm long tower bolt shall be welded to each openable shutter. 10 mm square guard bar shall be provided @ 125mm c/c.Details shown in CELZ Drawing No LZ/C-TD/130 SHEET NO 1/4 to 4/4 . Note: Glass panes and wire mesh shall be measured and paid separately under schedule of items.

S&F 4.00mm Sheet glass,ordinary quality fixed to window in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F Galvanised mild steel wire cloth,0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L for preparation of new surfaces of steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified and directed.

S&F PVC coated mild steel 25mm dia pipe as in curtain rods including brackets and fancy type end knobs complete all as specified and directed.

S & F in repair 18mm thick factory made 100% solid WPC flush shutter (for cupboard, wardrobe ,etc) made from co-extruded three layer rigid foam sheet Single extruded) with 0.8 to 1mm thick outer layer having density not less than 1400kg/cum and density of center core not less than 600kg/cum, with prelamination on both front and back side manufactured by and ISO 9001/2015 certified company complete all as specified and directed.

S & F Continuous (piano) hinges,mild steel, bright finish or electro galvanised width of flaps (when open in 40 MM) complete all as specified and directed.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S & F magnet catcher heavy duty for cupboard door shutter complete all as specified and directed.

S & F in repairs 'E' board Everest make 600x600x4mm thick white prelaminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24 x 32 x 300mm and spaced at 1200mm centers securely fixed to the structural soffts by approved hangers at 1200mm, maximum centrers.Hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level and jumper and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall, Flush fitting of 1200mm long cross tee (with double stiching) to be interlocked between main runners at 600mm centre to from 1200 x 600 mm modules cross tee longer than 600mm to be supported independently. 600x600mm dodules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross Tee, perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacturer's instructions complete all as specified.and directed.

M & L Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws incl Dismantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&l Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws incl Dismantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or other connecting plates Fe 410 -W (Gde-E- 250) quality- A complete all as specified and directed.

M&L 60mm thick rubber moulded glossy finish coloured interlocking precast PCC pavers any colour of M-35 grade laid over 25mm thick sand cushioning and joint filled with fine sand incl levelling, tamping and sweeping etc incl Dismantling stone slab and tiles of any description or and thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L construction of soakage well of size 3.0M dia x 4.50M effective depth with fly ash bircks and RCC M-25 design Mix using 20mm graded stone aggregate as in cover slab etc. including all required earthwork in soft/loose soil, returning filing and removal etc and filling of brick bats and cement concrete etc complete all as shown on CELZ drawing No TD/576 sheet 1/2 & 2/2 complete all as specified and directed.Note- filling of earth/rubble as ramming in old broken soakage pit and disconnection of inlet sewage line inclusive of this items complete all as specified and directed.

Supply of 3mm dia GI wire chain link fencing with 75x75mm mesh size and fixed to any type of strandard rails straining bolts etc including provision of binding wire complete all as specified and directed. Note: Weight constantant shall be detrmined by BOO of chain link fencing.

Fixing only chain link fencing including line wires, any mesh, size and type fixed to any type of standards rails, straining bolts, etc.including provission of binding wire complete all as specified and directed.

M &L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rqctangular or Polygonal complete all as specified and directed

M&L for Formwork to sides and soffits of floor or roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed

M&L for reinforced cement concrete (M-25) design mix as in foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slabs, under?reamed piles and mass concrete complete all as specified and directed

M&L for reinforced cement concrete (M-25) design mix 20 mm graded aggregates as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete (M-25) design mix 20 mm graded aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for mild steel TMT bars 8 mm dia cut to length, bent to shape and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc in stirrups, spacers and binders complete all as specified and directed.

M&L for plain cement concrete type B1, 1:2:4 (20 mm graded aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L for mild steel frame brackets of angle cut to shape, including welding , bending, embeding in concrete and screwing etc. including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) fixed in repair complete all as specified and directed.

Surface dressing n.exc 15cm deep and gettingout in soft /loose soil. complete all as specified and directed.

M&L hard core of broken bricks of gauge n.exc 63 mm deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to true surface complete all as specified and directed.

M&L for 100mm thick PCC 1:3:6 type C-1 (20mm graded stone aggregate) as in flooring complete all as specified and directed.

M&L 40 mm thick DPC with water proofing compound in PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) in horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

S & F steel work in roof trusses (framed), truss, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, agnle channel or flat sections including distance pieces, cleats etc. confirming to Fe -410 grade-250 B complete all as specified and directed

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Vitreous china countertop wash basin rectangular shaped size 565 x 415 x 190mm including CP waste coupling and waste pipe with all fittings complete all as specified and directed.

S & F chromium plated fancy type pillar tap, swan neck with angular cock 15mm bore complete all as specified and directed.

S & F jet spray with PVC pipe of superior quality complete all as specified.

S & F hand shower (health faucet) with 1 m long flexible tube suitable for hot and cold water supply including wall hook, bracket etc complete set of superior quality complete all as specified and directed.

S & F CP two-way stop/angle valves 15mm bore brass chromium plated, screwed down high pressure with castain head handle screwed both ends for iron pipes or for union complete all as specified and directed.

S & F for rotational moulded double layered polyethylene water storage tank cylindrical hoisted & fixed in position all as specified capacity 1000 ltrs complete all as specified and directed.

S & F vitreous china Water closet pedestal pattern with sheet cover white and flushing pipe 32mm dia for low level flushing cistern (excluding fixing bolts, flushing cistern and flush pipe) including Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe etc complete all as specified and directed.

S&F of looking mirror fancy type decorative pattern 5 to 6mm thick fixed on wall with stainless steel studs complete all as specified and directed

M & L for Granite stone slab 18-20mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixtures of pigment to match the shade of granite stone including grinding and polishing over cement screed bed 20 mm thick in CM 1:4 including cutting oval shape opening of size and shape as approved in granite stone slab to accommodate oval shape wash basin including rounding of exposed edges etc complete all as specified and directed.

M & L for 15-20mm thick polished Granite stone slab partition including polishing exposed edges, cutting chases in wall and inserting and fixing partition in cement mortar 1:4 as in urinal partitions complete all as specified and directed.

S & F Factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F 3mm thick plain sheet glass ordinary quality incl glazing with putty area n.exc 0.5 sqm in each pane complete all as specified and directed.

S & F 75mm bore CI Tee, single (equal or unequal), ordinary or inverted (Spigot or socketed type) or with parallel branches complete all as specified and as directed.

M&L for construction of septic tank for 50 users capacity, excavation and earth work in ordinary soil, foundation with PCC 1:2:4, type B-1, brickwork in CM 1:4, RCC 1:2:4 type B-0 slab, RCC precast manhole cover having 6mm plate embedded around with angle iron frame, vent shaft and sludge chambers etc all as shown on drawing no. TD/687 sheet 1/1 & 2/2 complete all as specified and directed.

Construction of Soakage well 2.4m dia and 4.5m effective depth, excavation in any type of soil, foundation in PCC 1:3:6 walls of honeycombed masonary with top ring of RCC 1:1.5:3 type A-1 including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab, interconnecting pipes complete filled with brick bats complete all as shown on drawing No. TD/576 sheet 1/1 & 2/2 complete all as specified and directed.

Taking down carefullycopper/aluminium point wiring (light, fan, socket or power) complete with fitting such as switches, sockets ceiling rose sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

M&L for point wiring with PVC insulated and unsheathed cable 1.5 Sqmm (nominal area) ISI marked multi-stranded copper conductor single core including 20mm dia medium grade PVC conduit concealed in wall / false ceiling, concealed terminal boxes not less than 1.6 mm thick of required size with top cover 2.8 mm thick of plastic laminated sheet (Hylum) of required colour complete metal flush terminal boxes with all accessories including 1.5 Sq mm PVC insulated and unsheathed stranded copper wire conductor cable to common earth and connecting to earth dolly including colour coding of cable shall be Phase - Red, Neutral- Black and Earth- Green complete all as specified and directed:- (a) One light/fan point controlled by one switch

All as item No 174 above but on the same board complete all as specified and directed.

All as item No 174 above but one socket outlet point 5 Amp on an independent board complete all as specified and directed

All as item No 174 herein before but using 2.5 sqmm , PVC insulated, stranded copper conductor single core cable for one 3 pin 15 Amp socket out let point on an independent board. complete all as specified and directed.

S&F switch piano flush button single pole one way 5 Amp 240 volt complete all as specified and directed

S&F ceiling rose surface bakelite three terminal complete all as specified and directed

S&F socket outlet flush type 5 pin 5 Amps 240 volts complete all as specified and directed

S&F angle type holder insulated body with back plate suitable for batten fittings complete all as specified and directed

S&F MCB DB sheet enclosure single pole and neutral 8 way 240V with 100/125 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 8 way double door complete all as specified and directed

S&F in repair MCB, single pole, 240 Volts (05 to 32) Amps,10Ka complete all as specified and directed

S&F in repair MCB, single pole & neutral, 240 Volts (16 to 40) Amps,10Ka complete all as specified and directed

Supply and Fixing wall/surface mounting luminaires integrated LED Batten 20/22 W, 6500 K,100 lumens/watt , 230V with extruded Aluminium housing 4 feet long with frosted PMMA/PC diffuser & integrated electronic driver, 25k burning hours ,2.5 KV surge protection complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as per specified and directed

Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V , minimum 100 lumens/watt,with extruded aluminium housing & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrngements all as per specified and directed

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed

Supply and fix exhaust fan, plastic body AC single Phase. 230V of size 250mm sweep with, blades, and frame and louvers including provn of flexible three core cable from ceiling rose to terminal for making connection , fitting on wall, including making recess on wall of required size and all necessary fixing accessories complete all as specified and as directed

S&F socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete all as specified and directed

S & F switch piano flush button single pole one way 15 Amp 240 volt complete all as specified and directed

Supply & fix fan regulator electronic step type for ceiling fan fixed, in existing board and connecting as directed, after dismantling and removing unserviceable regulator complete all as specified and directed

S&F sheet metal enclosures with socket plug top and MCBs with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed

S&F sheet metal enclosure (MCB DB) single phase and neutral with 100/125 Amps rated bus bar 12 way double door type , 240 volts as complete all as specified and directed

S&F sheet metal enclosure (MCB DB) single phase and neutral with 100/125 Amps rated bus bar 4 way double door type, 240 volts complete all as specified and directed

M&L for Sub main wiring with two single core PVC insulated cable with 4 sq mm nominal cross sectional area stranded copper conductor and one single core green PVC insulated 4 sqmm stranded copper conductor earth continuity cable drawn through non metallic rigid PVC conduit 20mm dia including all conduit and fixing accessaries concealed in wall including cutting chases in wall and making good disturbed surface to match of walls /ceiling complete. (Note-The cost of PVC pipe and accessoried shall be deemed to be included in the quoted rate)

S& F Decorative wall light fixture made up of Metal base, synthetic white in colour and square/round pvc globe with bend pipe nickel finish, ( B-22/E27 base), with 01 No. 7/9 W LED Bulb, 230 V, 6000K, complete incl all required electrical connecting arrangements complete all as specified and directed

S&F in replacement of LED Building security light 24/25 Watt with high power LED source (>110lumen/watt) PDC housing, IP65 and IK 07 with 4 KV inbuilt surge protection potted driver including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories such as bracket of GI pipe light grade 40 mm dia 0.60 mtr long bend to shape as per suitable size along with all accessories, fixed on wall including bolts & nuts complete all as specified and directed

Taking down carefully ceiling fan/exhaust fan of any size and type and refixing the serviceable fans in its original or new location complete all as specified and directed

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cables (heavey duty ) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 2 core complete all as specified and directed

Supply & Laying sub class `B’ bricks old sizes over the LT cable laid flat for protection of cable complete all as specified and directed

M & L of GI pipe medium grade of 40 mm dia base in trenches/ poles/walls for protection of cable including fittings complete all as specified and directed

M&L for point wiring with single core FRLS PVC insulated 1100V grade cable with multistranded copper conductor of size 1.5 Sq. mm (Nominal area) drawn in and including non metallic rigid PVC concealed conduit, medium grade ISI marked not less than 20 mm dia, concealed in wall, ceiling with saddles, screw & Plugs with all fittings including tee, junction boxes and drawing continuous earth wire of FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 1.5 sqmm and terminated in and including sunken box upto 8 module for modular switches/sockets, regulators etc complete all as specified and directed

All as per Item No 202 above but for one 5 pin 5 Amp socket outlet point on an independent board complete all as specified and directed

All as per Item No 202 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch complete all as specified and directed

All as per Item No 1 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm complete all as specified and directed

S&F modular switches 1 way 6A,1 module. complete all as specified and as directed.

S&F modular switches 1 way 16A,1 module complete all as specified and as directed.

S&F modular 6 A sockets-5 pin 2 module complete all as specified and directed

S&F modular 6A/16A sockets-3/5 pin combine 2 module complete all as specified and as directed.

S&F Modular white cover plate with frame 8 module complete all as specified and as directed.

S&F Modular white cover plate with frame 6 module complete all as specified and as directed.

S&F Modular white cover plate with frame 3 module complete all as specified and as directed.

S&F Modular white cover plate with frame 2 module complete all as specified and as directed.

Supply and fix modular type blanking plates, one module complete all as specified and directed.

S&F LED Building security light 20/25 Watt with high power LED source (>120 lumen/watt) PDC housing, IP66 and IK 08 with 4 KV inbuilt surge protection ,minimum 50000 burning hours hv cutoff@325/440 volt protection for 8 hours including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories complete all as specified and directed

Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

M/S KAUSHIK CONSTRUCTION (BID ID -3506341)

M/s Pratap Associates (BID ID -3506354)