COMPREHENSIVE REPAIR TO FENCING, WALL, DRAIN, HARDSTANDING ETC. FOR OTM ACCN AREA AT MIL STN UDAIPUR

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site ofm work as directed by the Engr-in-Charge.

Material and Labour for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base/mass concrete and finished the top surface even and fair complete all as specified by the Engr-in-Charge.

Material and labour for 300x300x20-25mm thick chequered cement concrete tiles rubberised moulded with grey cement and pigment set, jointed and pointed in neat cement slurry including laid over a screed bed of 20 mm thick in CM 1:6 complete all as specified and directed by the Engr-in-Charge.

Supply and fixing for PCC coloured interlocking (glossy finishing) paver blocks with grey cement and no pigments confirming to IS-15658-2006 of 60 mm thickness, M-35 grade as in hardstanding etc. laid over and including 50 mm thick screed or bedding layer of sand, complete all as specified by the Engr-in-Charge.

Supply and fixing for PCC coloured interlocking ( glossy finishing) paver blocks with grey cement and no pigments confirming to IS-15658-2006 of 80 mm thickness, M-40 grade as in hardstanding etc. laid over and including 50 mm thick screed or bedding layer of sand, complete all as specifiedby the Engr-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified by the Engr-in-Charge.

Material and labour for reinforced cement concrete Type B-1, 1:2:4 (using 20mm graded aggregate) Nominal Mix as in slabs supported on walls for culverts over open drains, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed by the Engr-in-Charge.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping), comlete all as specified and as directed by the Engr-in-Charge.

Supply and fixing for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and as directed by the Engr-in-Charge.

Ditto- but 6mm to 8mm dia (as in stirrups).

Demolition of brickwork or stone/boulder masanory,laid dry below or above ground level and removing material from site complete all as specified and directed by the Engr-in-Charge.

Material & Labour for Brickwork with fly ash bricks straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed by the Engr-in-Charge.

Material & Labour for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6, compelte all as specified and as directed by the Engr-in-Charge.

Material & Labour for brickwork with old size fly ash bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6, complete all as specified and as directed by the Engr-in-Charge.

Extra for forming fair finished drain or chamnnel 30 cm inner girth in cement concrete using extra cement including forms , moulds, complete all as specified and as directed by the Engr-in-Charge.

Add or deduct to above item for each 25mm girth or part thereof over or under 30cm inner girth, complete all as specified and as directed by the Engr-in-Charge.

Material and labour for cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate for fixing hold fast, coping, cills and filling in pressed steel door frames including necessary form work and finishing the surfaces to match with existing, complete all as specified and directed by the Engr-in-Charge.

Taking down cement plaster from brick walls ,concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed by the Engr-in-Charge.

Material and labour for Rendering 15mm thick on fair faces of concrete block masonry/brick masonry in cement concrete 1:6 cement mortar and finished fair and smooth all as specified by the Engr-in-Charge.

Material and labour for Rendering 15mm thick on stone masonry surfaces in cement concrete 1:4 cement mortar and finished fair and smooth all as specified by the Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed by the Engr-in-Charge.

Dismantling of barbed wire/round bar/fencing wire mesh any type and removing from site complete all as specified and directed by the Engr-in-Charge.

Material and labour GI Barbed razor type concertina coil of 610 mm dia (when unstrech) (having 15 Nos round per 6 metre length) fixed between 'Y' angle post and over barbed wire as per requirement with coil of coverage 6 running metre per coil, weight of each coil 9.50 Kg to 10 Kg hot dip galvanised and binding with and including MS annealed wire 0.90 mm complete all as specified and directed by the Engr-in-Charge.

Excavating in post holes (or similar holes) each n.exc 0.5cum, getting out in hard/dense soil, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm thick, complete all as specified by the Engr-in-Charge.

Excavation in trenches not exc 1.5m wide and n. exc 1.5m in depth, for foundation, etc. or for shafts, wells, cesspits, manhole, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in hard/dense soil.

Material & Labour cement concrete in foundation filling incl mass concreting PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete or in sub base complete all as specified by the Engr-in-Charge.

Material & Labour for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in boundary pillars and posts, incl necessary formwork complete all as specified by the Engr-in-Charge.

Supply and fixing MS angle as in posts and top membrane and Flat Iron for secure post/struts in fencing etc fixed in position conforming to Fe-410 (Gde E-250) (quality-A), complete all as specified and directed by the Engr-in-Charge.

Supply only chain link fencing of mild steel galvanised dia of wire 3.15mm thick and mesh size 50x50mm complete all as specified and as directed by the Engr-in-Charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed by the Engr-in-Charge.

Material & Labour mild steel round bar 10 mm dia and over, cut to length, bent to shape required and binding with MS wire (annealed) not less than 0.9mm dia as in reinforcement to columns and line bars to hold/support the chain link fencing secured hodizontally, complete all as specified and as directed by the Engr-in-Charge.

Supply & Fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and n exc 10cm long and dia of bolt 11 to 15mm complete all as specified and as directed by the Engr-in-Charge.

Material and Labour for two coats of synthetic enamel paint on new steel surfaces over a coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified by the Engr-in-Charge.

Material and labour for two coats of synthetic enamel paint on new steel surfaces over a coat of priming paint plaster coat surfaces plain or moulded, n exc 10cm width or girth when unconnected with other painting or when painted in a different tint,complete all as specified by the Engr-in-Charge.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil.

Removing excavated material (soils) not exc. 50 m and depositing in soft/hard soil, where directed, complete all as specified and as directed by the Engr-in-Charge.

Material and Labour for applying two coat of white wash on wall surfaces incl preparation of newly plastered wall surfaces complete all as specified and directed by the Engr-in-Charge.

Punjab Traders (BID ID -3061334)

shree nathji trading corporation (BID ID -3069874)

naveen enterprises (BID ID -3062257)