REPAIR MAINT OF CERTAIN ROADS AND ROAD FURNITURE IN POCKET A AND B AT JASAI MIL STATION UNDER GE (A) BARMER

M&L for repair to pot holes any depth area not exceeding 1.0 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths etc. cutting around edges to atleast 25 mm in depth, making good by applying tack coat VG-10 at 5 kg per 10 Sqm, putting in premix bituminous macadam well rammed and sealed with binder 9.8 kg per 10 sqm binded with 0.09 cum of stone chipping, 6.3 mm size and again well rammed (including supply of premix binder and sand) with 8 to 12 tonne power roller depth of pot holes not exc. 30mm complete all as specified and directed.

M&L for Preparation of old black top surfaces of any type by brushing with wire brushes for removing cake mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to removed all loose dirty etc.Applying evenly a tack coat of cationic butumen emulsion (RS-1) confirming to IS: 8887 at a rate of application of 5kg/10sqm fo bituminous surface as specified in table 500-5 of MoRTH specification for road and bridge works 2013, using mechanical sprayer all as specified and directed.

M&L for premixed bituminous semi-dense asphaltic concrete 30mm consolidated thickeness laid using mechanical paver for any width of road with 5.50% binder content, paving butimen VG-40 grade by weight of total mix, rolled and compacted to required camber and gradient using 8 to 10 tonne power roller complete all specified & directed.

M&L for Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400 sqm, n.exc 50mm deep complete all as specified and as directed.

M&L for Preparation of unsurfaced waterbound macadam surface of any type by brushing with wire brushes for removing cake mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to removed all loose dirty etc. Applying evenly a tack coat of cationic butumen emulsion (SS-1) confirming to IS: 8887 at a rate of application of 0.7 to 1.0 kg/sqm on surface of WMM etc as specified in table 500-3 of MoRTH specification for road and bridge works 2013, using mechanical sprayer all as specified and directed.

M&L for premix bitumen macadam with pavment bitumen (VG-40) content 4.50 % by weight of total mix laid by mechanical mixer paver /rolled compaced & rolled to required gradient and camber with 8 to 10 tonne capacity power roller (consolidated thickness of BM 75 mm or less) complete all as specified and directed.

M&L for preparing bituminous surface of road and marking 2.00 mm thick centre lines, stop lines, dashes, arrows etc and the like n exc 10 cm wide on roads pavements with hot applied thermo plastic road marking paint with glass beeds of approved colour conforming to BS 3262 -1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed.

S&F in repair cat eye solar two side reflective type of metal aluminiumstud body alloy of size 110mm x 120mm x 20mm with PMMA strip lens reflector of suitable size as per manufactures instructions fixed with epoxy complete all as specified and directed.

S&F in repair solar cat eye aluminum alloy shall (100% water proofing design according to IP 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono crystalline solar panel 2.4V/ 0.3 watt one NI-cd rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instruction fixed with epoxy etc complete all as specified and directed.

S&F in repair metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed.

S&F in repair smart solar tubular dealineator of 1mtr height, modal No DA-112 , of material polycarbonate ABS and battery 1.2 V including embedding in PCC 1:2:4 (150x150x300mm) type B-1 complete all as specified and directed.

M&L in repair for identification sign/cautionary mandatory and information sign board area exc 0.60 Sqm and n exc 1.20 Sqm with thickness not less than 3.0mm aluminium composite panel covered by encapsulated lens type retro reflective sheet (grade 3M type II diamond grade of make 3M/dark eye/SNI ) on both side with green base, including writing of necessary letter/symbols of reflective type fixed on and including stainless steel frame of size 25mmx25mm and hang on 50mm dia stainless steel pipe(fabrication work from SS-304 material) of height 2.4 mtr from ground level to top and post embeded in ground with PCC 1:3:6 TYPE C-2 using 40mm graded aggregate of size 45x45x45cm including necessary excavation and earth work and making plateform of size 150x45x30cm with PCC 1:2:4 using 20mm graded aggregate including necessary formwork and covering all exposed surfacess with black colour glazed ceramic tile (joint less) of size (600x300x7mm) / (450x300x7mm thick over and including 10mm thick backing coat in cement mortar(1:4) set and jointed in neat cement slurry and pointed to match the tiles complete. Note:- The specifaction of board is held with GE(A) Barmer as sketch. The letters and symbols etc on both side shall be as per site requirement of user and as approved by GE. The size and font of wording/ arrow/ symbols as per direction of Engineer In-Charge.

M&L for one coat of synthatic enamel paint on old concrete surface including surface preparation of any description (Road side cement concrete kerb stone in ZABRA Pattern) complete all as specified and directed.

Demolition of concrete in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and directed

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for cement concrete 1:2:4 (20mm graded stone aggregate) as in Coping, Roof covering laid in slope, Holdfast including necessary formwork and weathering, slightly rounded or chamfered angles and throating, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for 300mmx300mmx10mm thick non skid polka dots parking floor paver tiles with grey cement and pigment, over and including 15mm thick screed in CM (1:4), set jointed & pointed in neat cement slurry in floors complete all as specified and directed.

M&L for two coat of synthatic enamel paint over a coat of primer on new concrete surface including surface preparation of any description (Road side cement concrete kerb stone in ZABRA Pattern) complete all as specified and directed.