SPECIAL REPAIR REPLACEMENT OF EXISTING WIRING LIGHT FITTINGS IN MD AND OTM ACCN AND REPLACEMENT OF ILLUMINATION LIGHT AT SPORTS GROUND ENTRANCE OF MAIN GATE AT AIR FORCE STATION BORGAD

Amount

Taking down existing copper/aluminum point wiring (light/ fan/ socket or power points) complete including (fittings such as switches, ceiling roses, pendents, regulators, sockets, Light fitting etc including wooden battens /casing /capping and conduit etc and making good disturbed surface of walls, ceilings and floors etc. complete all as specified & as directed by Engineer-in-Charge.

Taking down carefully sub main wiring including all accessories without disturbing existing wiring fittings fixture site and making good to the disturbed surfaces all as directed and as specified in any type and size.

Taking down main switch, DB, MCB, and electric Meter etc all as directed.

Material & Labour for Point wiring with 1.5 Sqmm (nominal area) FRLS ISI mark ,PVC insulated sheathed copper stranded conductor cable run in and including concealed in wall/floor PVC conduit,medium grade not less than 20 mm as per IS with all fittings such as bends, tee,junction boxes,etc of suitable size including 1.5 Sqmm FRLS ISI mark ,PVC insulated copper earth continuity conductor connected to common earth dolly and including MS/GI sunken boxes with modular inner & surface plate suitable for housing modular switches, sockets,fan regulators etc for one light/fan/call bell point controlled by one 1- way switch complete all as specified and as directed by Engr -in -Charge..(Note: Cutting and making good of chases in the wall/ Roof/ Floor including making good of disturbed surfaces and painting to match with existing touch up etc are deemed to be included in the quoted rate.)

All as per item No 4 here-in-before but for one 3 pin 5 Amps socket outlet on independent board.

All as per item No 4 here-in-before but for one 3 pin 5 Amps socket outlet on the same board with other switch with 1.5 sq mm size.

All as per item No 4 here-in-before with 2.5 sq mm size cable, for one 6 pin 5/15 Amps socket outlet on independent board.

M&L wiring for circuit/ sub main wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core, 1100 v grade cable in conceled/surface as required using 2x4.0 Sqmm+1x4.0 Sqmm earth wire,cables inciuding run in PVC Conduit medium grade of suitable size and taking down old unserviceable submain from existing position ,complete all as specified and as directed by Engineer-In-Charge (Note: 4 run of 4.0 sq mm & 1 run of 4 sq mm in PVC Conduit medium grade of suitable size combined shall be measured & paid as one unit )

Modular switch one way 6 Amp,1 Module , Make Legrand Mylinc/ L&T/Crabetree, complete all as specified and directed by Engineer-in-Charge

Supplying and fixing Modular socket, 6 amps-2/3 pin combined, 2 Module, Make Legrand Mylinc/ L&T/Crabetree, complete all as specified and directed by Engineer-in-Charge

Supplying and fixing Modular switch , one way, 16 amps, one Module of Make Legrand Mylinc/ L&T/Crabetree, complete all as specified and directed by Engineer-in-Charge

Supplying and fixing Modular socket 16 amps-6 pin multipin, 2 Module of Make Legrand Mylinc/ L&T/Crabetree, complete all as specified and directed by Engineer-in-Charge

Supply & Fix Modular Fan regulator electronic step type 230 V 2 Module. Make Legrand Mylinc/ L&T/Crabetree, complete all as specified and directed by Engineer-in-Charge

Supply & Fix Ceiling rose surface type, PVC/Polycarbonate isolated body size 50x28 mm three terminals. Make : Anchor/Legrand, complete all as specified and directed by Engineer-in-Charge

Supply & fix in repair decorative ultra slim square profile linear DELITE LED lighting fixture extruded polycarbonate, enviromental frendily, energy efficent ready to use pack not less than 18W LED 6000K, complete with connecting accesseries duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting, complete all as specified and directed by Engineer-in-Charge. MAKE : Havells, Model No. LHEXBTP7UN1W018 or equivalent in Bajaj/ Crompton Greaves.

Supply & fix in repair decorative ultra slim square profile linear D-ELITE LED lighting fixture extruded polycarbonate, enviromental frendily, energy efficent ready to use pack 9W LED 6000K, complete with connecting accesseries duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting complete all as specified and directed by Engineer-in-Charge. MAKE : Havells, Model No. LHEXBTP7UN1W009 or equivalent in Bajaj/ Crompton Greaves.

Supply & fix in repair decorative ultra slim square profile linear DELITE LED lighting fixture extruded polycarbonate, enviromental frendily, energy efficent ready to use pack 5W LED 6000K, complete with connecting accesseries duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting complete all as specified and directed by Engineer-in-Charge. MAKE : Havells, Model No. LHEXBLP7IN1W005 or equivalent in Bajaj/ Crompton Greaves.

Supply only in repair New generation energy saving & enviromental friendly long life versatile pressure die cast aluminium IP66 with high power road way luminaireNEXUS+ with SPD street light fitting, lamp type 45W LED 6000K , deep drawn aluminium pipe mounting attachment complete and connecting with 3 core PVC insulation PVC sheathed copper cable of size 1.5 Sqmm from junction box to street light and testing complete model No LSTP-45 -CDL Asymmetric optics of Make : Crompton or equivalent in Bajaj/wipro/Havells including taking down old unserviceable fitting from existing position complete all as specified & directed by Engineer-In-Charge.

S&F Exhaust fan 300 mm sweep with louvers, operated on 230/240V AC Single phase electric supply 900 RPM complete duly grauted bolts in the wall fixed with nuts, bolt and washers including making suitable size hole in the existing wall, plastering, white washing or colour washing to the disturbed surface of wall complete matching with the existing including connecting with 3 core stranded copper conductor cable cord of size 0.5 sqmm from ceiling rose to fan connector complete all as specified and directed. Make:- Havells Turbo Force or equivalent model of Bajaj/CG.(Rates quoted are deemed to be included with making hole as per fan sweep dia & making good of damaged surface & plastering & painting to match with existing touch up.)

Supply & fix tempra plug & socket DB for DX3 Lexic MCB 32A 2P+E-DP cat part no 607880 of Make Legrand, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair MCB SPN 32 amp 240 V,10KA, C curve,DX3 series of Make Legrand cat part no 408617 complete all as specified & as directed by Engineer in charge.

Supply and fix in repair MCB SP 6-32 amp 240 V,10KA, C curve,DX3 series of Make Legrand cat part no 408595 complete all as specified & as directed by Engineer in charge.

Supply and fix in repair double door sheet metal enclosure for DBs when MCBs to be used single pole and neutral IP 43 IK-09 protection with acrylic door for DX3/MCB , 240 volt , rated bus bar bar 8 way of Make Legrand Cat No 507621 or equivalent model of L&T/Siemens complete all as specified & as directed by Engineer in charge.

Supply & fix in repair double door sheet metal enclosure distribution board recessed mounting 230 volt SPN DB for DX3/Lexic MCB ,IP 43 IK-09 with acrylic door for DX3/MCB, 4 way of Make Legrand cat part No 507620 complete all as specified & as directed by Engineer in charge. (Note: Outgoing MCB will be measuserd & paid under relevant item)

Supply & fix in repair sheet metal enclosure distribution board recessed mounting 415 volt vertical TPN DB DPX3 160 MCCB DB ,IP 43 IK-09 , 4 way with metal door of Make Legrand cat part No 507745 with MCCB 63 Amp Four pole 16 KA ,DPX3 160 series as incomer of Make Legrand cat part No 420013 and SP/TP MCB as outgoing as per IS including compact insulated bus bar and rounded neutral,door earthing complete all as specified & as directed by Engineer in charge. (Note: Outgoing MCB will be measuserd & paid under relevant item)

Material & Labour for earthing lead fasteners etc and earthing complete with copper earth plate electrode 600x600x3.15 mm thick,burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of the plate not less than 1.5 Mtr below normal ground level,connected to 20×3 mm copper strip as earth lead by means of copper bolts,nuts ,washer and check nut of galvanized steel, protected by and including GI pipe 40 mm bore (light grade) and connected to main switch / MCB DBs box point / LP test point as directed and including cement concret pit in 1:2:4 type B1 using 12.5mm graded aggregate, with cast iron miled steel frame embedded in the concrete enclouser fineshed flushed & CI cover 10 mm thick of size (300mmx300mm CI) having locking arrengment hinged to CI frame all as shown under electrical plate of SSR Pt - I 2009 and as directed including painting the external surface of chamber & cover with enamel paint in diffrent colour as directed and writing earth results & date of test carried out with white paint on black painted background, wiremesh funnel 20 mm bore GI pipe medium grade for watering adequate quantity of charcol ,Bentonite and common salt in alternate layer of 15cm 3ft x 3ft thick all around the electrode including necessery excavation & earth work in any type of soil/strata/rock complete testing on completion all as directed. Note:- i) Filling the pit with black cotton soil brought at site. Testing on completion &achieving resistance less than 3 ohm & submitting report to Engineer-In-Charge duly signed by user in every month after successful completion of earthing during contract period & defect liability period all as directed. iv)If resistance value is more than 01 Ohm , contractor has to redo or rectify the earthing within 07 Days without any extra cost .

Supply and laying ,testing & commissioning 1100 volt grade XLPE insulated armoured heavy duty LTUG stranded aluminium conductor 4 core cross sectional area 25 sqmm in trenches/ducts / passing through pipe or laid on surface with help of saddle including taking down old unserviceble cable from existing position complete all as specified & as directed by Engineer in charge.

Supply and laying ,testing & commissioning in trenches/ducts or passing through pipe/laid on wall with help of proper saddle 1100 volt grade LTUG cable with XLPE insulated armored heavy duty electric cable with stranded aluminium conductor 1100V grade 2 core cross sectional area 6 sqmm, complete all as specified and directed by Engineer-In-Charge.

Supply and lay in trenches/ducts or passing through pipe in repair ,testing & commissioning LTUG cable 2 core 10 Sqmm, 1100 volt grade, XLPE insulated armoured (heavy duty) stranded aluminioum conductor complete all as specified

Excavation in trenches not exceeding 1.50 mtr wide and not exceeding 1.50 meter in depth and getting out in soft/loose soil all as directed complete all as specified & as directed by Engineer in charge.

Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm all as directed complete all as specified & as directed by Engineer in charge.

Removing of surplus soil not exceeding 50 meter and depositing where directed at a level not exc 1.50 mtr above the starting point all as directed complete all as specified & as directed by Engineer in charge.

Supply and laying Double walled corruyated (DWC) Duct (Dura- Guard) as per IS-14930 Part - II for LT UG cable protection including coupler, elbows, T- Joint, Bends, etc and test report Make :- Dura- line/Gemini/Rex. Of size 38mm

M&L for galvanised steel water tubing light grade with all fittings laid in trenches of size 40 mm dia bore for cable protection under road/Path ,complete all as specified and as directed by Engr-in-Charge.

S&F Exhaust fan 450 mm sweep with louvers, operated on 230/240V AC Single phase electric supply 900 RPM complete duly grauted bolts in the wall fixed with nuts, bolt and washers including making suitable size hole in the existing wall, plastering, white washing or colour washing to the disturbed surface of wall complete matching with the existing including connecting with 3 core stranded copper conductor cable cord of size 0.5 sqmm from ceiling rose to fan connector complete all as specified and directed. Make:- Model No Turbo Force of Havells, or equivalent model of CG/Almonard.

Material & Labour for wiring street light circuit with 3x2.5 Sqmm wire, of PVC (FRLS) insulated stranded copper conductor, single core, 1100 v grade cable in and including 15 mm GI medium grade pipe fixed to PCC rectangular cross section / steel tublar street light pole with 25x3 mm MS brackets/ clamps, nuts, bolts and washers duly painted with aluminium paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Electricaly isolating & taking down carefully street /security lights/flood lights fitting including brackets & wiring from poles,top of building OH reservirors etc of any type & capacity from existing position ,cleaning & servicing at refixing at another location , complete all as specified & directed by Engineer-In-Charge.(Note : All fittings are to be fixed on bracket upto 9 meter height from ground on steel tubular/RCC pole)

Supply & Fix specialy designed Rectangula LED floodlight luminaire with innovative thermal management and available with multiple optics , in order to provide lightening level 350W LED 6000K(120 lumen per watt along with surge protection device), IP 66 flood light with high power LED as light source, Cat part No LSFO-350-CDL/60 of Make Crompton or Equivalent in Havells/Philips,duly mounted over suitable MS bracket coated with redoxide & two coats of synthetic enamelled paint, complete all as specified & as directed by Engineer-In-Charge.(Note : All fittings are to be fixed on bracket upto 9 meter height from ground on steel tubular/RCC pole)

Supply,install testing & commissioning 11 KV LBSF panel within existing site condition with two outgoing as LBSF panel complete with 630 A load break switch-02 nos,HRC fuse trip system -06 nos,Earth switch -02 nos,room space heater with thermostat -02 set, along with PVC sleeved copper bus bas bar for incommming,door interlocking mechanism,tripping mechanism ,Epoxy insulator for bus support, HV cable box provided for end termination at incomming side end plate provided at outgoing side for end termination / provision of Bus duct with copper bus bar for connecting with HT side of 11 KV VCBr & feeder pillar type copper bus for branch connection of HT 11 KV supply Manufactured by EL -TECH CONTROL, complete all as specified and directed by Engineer-In-Charge.

M&L for cable joint termination box PVC body housing suitable for housing and including 100 amps rated aluminium bus bar,suitable MCB SP, 3 phase, 4 wire system mounted on PVC insulators for one incomming and two out going cable entry space mounted on street light PCC/ tublar pole with 25x3 mm FI clamps with nut, bolts washers and for street light supply of Make: Sintex & double compression gland of Make : Dovel or comet, complete all as specified and directed by Engineer-in-Charge.

metro electrical services

LOKMANYA ENTERPRISES

Anand Trading Co

Datar Electrical and Engg Services