Special repairs to Bldg No. P-6 to P-13 Offrs Md Accn at Old Mil Stn Kapurthala under GE Kapurthala.

Amount

Demolition of brick / block masonry built in CM including all quoins, arches, pillars etc and clearing off the premises complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness(below or above ground level) complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work incl cutting reinforcement as required to facilitate demolition complete all as specified and directed by Engineer-in-charge.

Material & labour for PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands plinth cources, roof kerbs or mud stops, benching, coping, bed plates, parapets, water throughs and the like etc including weathering, slightly rounded or chamfered angles throating etc complete including necessary form work complete all as specified and directed.

Material & labour for RCC (1:1½:3) type A-0 using 12.5 mm graded crushed stone aggregate as in RCC projection, chajjas, fins,louvers fascia, arches & like including 5mm thick rendering in CM 1:3 finished even and smooth without using extra cement complete including necessary form work complete all as specified and directed.

Material & labour for mild steel TMT bars 6 to 8 mm dia, cut to length bent to shape required, including cranking, hooking ends, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-charge.

M&L for use and waste of formwork to chajjas and similar items including edges rough finished surface complete all as specified and directed by Engineer-in-charge.

Dismantling of 100/75 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Material & labour for cast iron soil, waste and vent pipe of bore 100mm, sand cast type in any length with or without ears with cement joints fixed to wall/laid in trenches complete all as specified and directed.

Material & labour for cast iron soil, waste and vent pipe of bore 75mm, sand cast type in any length with or without ears with cement joints fixed to wall/laid in trenches complete all as specified and directed.

Extra over 100mm dia cast iron pipes and fittings if lead joint is provided in lieu of cement joints complete all as specified and directed by Engineer-in-charge.

Extra over 75mm dia cast iron pipes and fittings if lead joint is provided in lieu of cement joints complete all as specified and directed by Engineer-in-charge.

Material & labour for cast iron bends (any radius), diminishing pieces or tapers of size 100mm with inspection eye complete all as specified and directed.

Material & labour for cast iron bends (any radius), diminishing pieces or tapers of size 75mm with inspection eye complete all as specified and directed.

S&F in repair PTMT grating round 140mm size (min weight 50 gms) complete all as specified and directed.

S&F in repair PTMT grating square 150mm size (min weight 100 gms) complete all as specified and directed.

S&F in repairs CI floor trap with grating and diameter of outlet 75 mm including jointing to waste pipe fixed in in run lead joint complete all as specified and directed by Engineer-in-charge.

S&F in repairs CI floor trap with grating and diameter of outlet 100 mm including jointing to waste pipe fixed in in run lead joint complete all as specified and directed by Engineer-in-charge.

Material & labour for 25mm thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate), as in leveling concrete in floor finished even & rough to receive top floor layer/finish complete all as specified & directed.

Taking up or down GI tubing & connection 15mm dia laid in floor / trenches or fixed to walls complete all as directed by Engineer-in-Charge.

S&F GI tubing 15mm dia medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.

Taking down GI tubing & connection 25 mm dia laid in floor / trenches or fixed to walls complete all as directed by Engineer-in-Charge.

S&F GI tubing 25 mm dia medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded aggregate as in sub base complete all as specified and directed by Engineer-in-charge.

Material & labour for cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sun shades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth in brick walls complete all as specified and directed.

M&L for glazed ceramic colour tiles of size 300mmx200mm x 7mm thick on vertical surfaces such as in skirting, dado etc over and including 10 mm thick backing coat in CM 1:4 incl set and jointed in neat cement slurry & pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles, over and including 15 mm thick cement screed bed in CM (1:6) complete all as specified and directed by Engineer-in-charge.

Material & labour for vitrified ceramic tiles 10mm thick, dark shade as approved, polished area of each tiles n. exc. 0.36 Sqm (square / rectangular) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed 15mm thick in cement mortar (1:6) finished rough to fix tiles complete all as specified and directed.

Material & labour for granite (of any type) work, 18-20mm thick machine cut (table rubbed and polished) in steps jambs, pillars, window cills, cooking platforms, shelves in cupboard, handwash places and like including necessary cutting and grooving to walls and making good over and including 15mm thick in cement mortar (1:6) screed bed or bedding layer and pointing with cement mortar (1:2) with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F in repairs galvanised mild steel wire cloth 0.63mm nominal dia of wire and avarage width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-charge.

S&F in repair brass chromium plated towel rail 20mm dia D type, 600mm long between flanges including CP brass screws and wooden/plastic cleats (Minimum weight 190 gms) complete all as specified.

S&F in repairs 15 mm bore CP bib taps cast copper alloy with crutch or butter fly handle long body with wall flange and aerator screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-charge.

Supply & fix in repairs PVC connection 15mm bore size with PTMT nuts of length 600mm complete all as specified and directed.

S&F 15mm bore brass chromium plated angular basin inlet connection (Angle valve) quarter turn, with wall flange fancy type cast copper alloy of any colour complete all as specified and directed.

Supply & fix in repairs pillar taps cast copper alloy with capstan heads, chromium plated, 15mm bore screwed down high pressure with lettered Hot and Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

Supply & fix in repairs wash hand basin vitreous china, flat back, size 550 x 400 mm with a set of CI brackets, brass chromium plated waste fittings and PVC waste pipe 32 mm bore, connection to water tubing, PVC connection 15mm dia with brass check nuts complete all as specified.

Supply & fix in repairs squatting pan WC Orissa pattern size 580mm x 440mm white with integral foot rest (excluding flushing cistern) with P or S trap including provision of lime concrete bedding and making good to match with existing surfaces complete all as specified and directed.

Supply & fix in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste coupling, including bedding in cement mortar (1:2) to dwarf wall, or including fixing cantilever brackets, connecting union to pipe and waste down pipe etc, overall size 1165mmx505mm with bowl size 405mm x 405mm x 230mm complete all as specified and directed.

Supply & fix brass chromium plated mixture valve centre hole, cast copper alloy (ISI marked) fancy type chromium plated for mixing hot and cold water screwed down high pressure with capstan head screwed both ends for iron pipe 15 mm bore dia complete all as specified and directed.

Supply & fix in repair brass chromium plated wall mixture with 115mm bend pipe for connection to overhead shower for mixing hot and cold water screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F in repairs 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butter fly handle screwed both ends for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

S&F in repairs 15mm dia fancy type two way stop valve chromium plated, cast copper alloy with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe or for union complete all as directed by Engineer-in-charge.

S&F acrylic toilet cabinet with shelves, of size 425mmx350mmx100mm with shutter complete all as specified and directed by Engineer-in-charge.

Supply & fix in repair stainless steel kitchen plate rack made out of 1mm thick stainless steel of size 600 x 750 x 200mm with shelves and plate partition of pattern as approved by engineer-in-charge, fixed to wall by means of four nos rawl plugs complete all as specified and as directed.

Supply & fix in repair stop valve fancy type chromium plated (concealed) type with long shank & cup 15mm bore, cast copper alloy, screwed down with high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed.

Supply & fix in repair chromium plated stop valve/angle valve 15mm bore, cast copper alloy, screwed down high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed.

Supply and fix vitreous china ware wash hand basin, flat back of size 580mmx460mmx210mm with long pedestal, 32mm dia stainless steel waste coupling and CI brackets incl cutting for and pinning ends of brackets or erecting stand and including, connection to water tubing, PVC connection 15mm dia with brass check nuts complete all as specified and directed

Supply & fix coloured chromium plated toilet paper holder fixed to walls using CP brass screws complete all as specified and directed..

Supply only liquid integral water proofing compound complete all as specified and directed by Engineer-in-charge.

Supply and fix in repair health faucet including CP angle cock 15 mm bore complete all as specified and directed by Engineer-in-charge.

Supply & fix in repairs soap dish 160x160x90mm size steel of stainless steel fixed to wall with plugs and chromium plated screws complete all as specified and directed.

Supply & fix in repairs coat hooks of 6 Nos aluminium powder coated mounted on aluminium powder coated plate 50x300mm fixed to walls complete all as specified and directed.

Supply & fix in repairs glass shelf 450x150mm and 8 mm thick with CP bracket guard and railing 60 cm long complete all as specified and as directed by Engineer-in-charge.

Supply and fix in repair corner glass shelf of size 300mm dia and 8mm thick with chromium plated bracket with and including chromium plated brass screws and wooden/plastic cleats, complete all as specified and as directed.

Material & labour for 25mm dia mild steel pipe curtain rod, powder coated fixed with & including aluminium powder coated hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

M&L for hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames including punching or drilling out old glazing pins/spring clips glazed with putty or fixed with beads and providing and fixing new ones exceeding 0.5 Sqm complete all as specified and directed.

Supply and fix 3 mm thick plain sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Supply and fix 3 mm thick plain sheet glass frosted, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Taking down chowkats or framed with shutter (with out taking off shutters from the frame) area not exc 1.50 sqm each complete all as specified and directed by Engineer-in-charge.

Taking down chowkats or framed with shutter (with out taking off shutters from the frame) area exc 1.50 sqm but not exc 4 Sqm each complete all as specified and directed by Engineer-in-charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and avarage width of aperture 1.18mm and fixed with tinned tacks/screws with bolts incl leaping wooden complete all as specified and directed by Engineer-in-charge.

Supply & fix Steel windows 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mm x 25mm single rebated comprises of glazed skeleton shutter EWR Sec 50mmx20mm and 1mm thick and two open able leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box type ‘T’ section of size 60mmx25mm and 1.25mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B1 using 20mm graded stone aggregate including following fittings welded to framed shutter :- (a) Holdfasts 150mm long 12mmx3mm made to shape per window -04 Nos, (b) Handle of Z Sec 20mmx25mm, 100mm long per leaf-01 No, (c) MS tower bolt 150mm long per leaf -02 Nos, (d) ‘Z’ sec 20mm x 25mm, 100 long stopper per leaf -01 No, (e) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges per leaf -01 No, (f) MS pintal hinges of size 75mmx12mm per leaf -02 Nos, (g) Fabrication and fixing arrangement as per drawing No CEJZ/TD/1019, Sh 1/3 to 3/3 and No. CEJZ/TD/1020, Sh 1/3 to 3/3. Note : Glass, grills & painting shall be measured & paid for separately and irrespective of whatever shown on drgs, MS grills shall be of 12 mm dia MS square bar.

All as per srl item No. 66 here in before but of gauged shutter. Note for item No. 66 & 67 :- Drg No. CEJZ/TD-1019 & 1020 are not being uploaded and the same can be seen in office of CWEJRC on any working day. Wire gauge, grill & painting shall be measured and paid for separately

Supply and fix 2nd class hard wood (hollock) factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in clause 8.24 (a) of SSR Part-I; supplied and fitted to chowkhats complete all as specified and directed.

Supply and fix 35mm thick 2nd class hardwood (hollock) factory made plain framed, panelled shutters (two panels), with lock rail and panels of 9mm thick BWP commercial ply or of venered particle board 12mm thick with commercial veneering on both faces with rails and style of 2nd class hard wood. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply & fix factory made PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, but fitted with stainless steel wire guaze panel stretched firmly at edges, wrapped on an additional square 8 mm M S tube all as specified in SSR part II complete all as per specified and as directed by the Engineer in Charge.

S&F solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and directed by Engineer-in-charge.

Supply & fix pressed steel frames made out mild steel sheet 1.25 mm thick PBI sheet, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc including tarring ends and back of chowkhats and lugs including back filling of PCC 1:3:6 for chowkhats & PCC 1:2:4 for block for hold fast and including applying to coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

Supply and fix factory made solid PVC moulded door shutter with full particle board core 30mm thick (stiles), with 2, 4 or 6 raised panel design with 5mm thick moulded prelam PVC sheet on front face and 2mm thick plain colour PVC sheet on back face complete as per specification & all as specified and directed.

Supply & fix factory made PVC Cupboard Shutter Flush type of 25mm thickness consisting of panel of hollow PVC profile of 12mm x 12mm inserted all around the hollow profile section and insert one 10mmx10mm MS tube in the centre of this section and lipped with 10mm(5mmx2) thick and 12mm wide on stiles and rails using solvent cement, the inner panel shall be laminated with 5mm thick termite proof, water proof and fire retardant printed PVC sheet using solvent cement on both the sides of the panel.The front side of the panel visible in the front of the shutter to be edge bonded using 20mmx1mm thick PVC leeping on both the edges with locking arrangement of both panels etc complete as per direction of Engineer-in Charge & Manufacturers's Specification.

S&F PVC cupboard frame of size 75mm x 40mm with wall thickness of 5mm made out of extruded 5mm thick plain/printed/prelam PVC sheet reinforced with 15mm x 15mm M.S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners and jointed with 2 Nos. of 150mm long brackets of 10mm x 10mm MS square tubes the door frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using PVC fasteners, a min of 4 Nos of screw to be provided for each vertical member and minimum of 02 Nos of screws to be provided horizontal member etc complete all as specified and directed by Engineer-in-charge.

S&F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt is 150mm complete all as specified and directed by Engineer-in-charge.

Supply & fix 40 mm dia cupboard knobs of brass duly polished, with nuts, screw and washer of mild steel bright finished complete all as specified and directed.

S&F magnetic type catch fixed with screws to door frame complete all as specified and directed by Engineer-in-charge.

Supply and fix 100 mm long extruded aluminium alloy anodised butt hinges with galvanized mild steel hinge pin type B 21 complete all as specified and directed.

Supply & fix extruded aluminium alloy handles, cast type, anodised, 150mm size, all as specified and directed.

Supply & fix in repair mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Taking down cement plaster/ terrazzo cast in situ of any description thickness including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

M&L for 15 mm thick cement plastering in cement mortar (1:4) of brick work or concrete surfaces with using water proofing compound finished even & smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick cement plastering in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall/ceiling and applying 3mm thick wall care putty to obtain the true line to achieve smooth surface and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparing surfaces of new walls and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying 3mm thick wall care putty to obtain the true line to achieve smooth surface and applying one coat of oil bound distemper complete all as specified and directed.

M&L for preparation of old decorated brick/concrete plastered or unplastered surfaces of walls including pillars, cornices etc brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, graeacy spots etc incl removal of existing treatment and applying two coats of cement base paint complete all as specified.

M&L for preparation of old plastered surfaces of wall and applying 3mm thick wall care putty to obtain the true line to achieve smooth surface and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of walls including pillars, cornices etc brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, graeacy spots etc incl removal of existing treatment and applying two coats of interior plastic emulsion paInt complete all as specified and directed.

Material & labour for preparation of old/new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Material & labour for preparation of old/new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Supply & fix in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with top push type button with inlet ball valve and float, handle with bracket PVC short bend etc. complete all as specified and directed.

Supply & fix in repairs vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts flushing cistern and flush pipe) including plastic water closet sheet cover, health faucet with 1 mtr long flxible tube in chrome finish & wall hook complete all as specified and directed.

Supply & fix in repairs brass chromium plated shower rose with CP arm any size with or without swivel joints including fixing to steel pipe or union of 15mm bore complete all as specified and directed

Dismantling existing water storage tanks of capacity 500 litr to 1000 litre setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required, reconnecting and refixing in position all as specified in SSR of any description, capacity complete all as specified and directed.

Supply & fix in repairs rotational moulded polythene water storage tank triple layer, ISI Marked of capacity 1000 litre cylindrical vertical with closed top, hoisted in position complete all as specified and directed.

Supply & fix in repairs rotational moulded polythene water storage tank triple layer, ISI Marked of capacity 500 litre cylindrical vertical with closed top, hoisted in position complete all as specified and directed.

Supply & fix in repairs ball valve PTMT with epoxy coated aluminium rod and high density plastic ball complete screwed for 25mm bore dia of iron pipe or brass ferrule complete all as specified (Minimum weight 210 grams).

Supply & fix in repairs 25mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Demolition of mud in roofs any thickness including plastering and leeping (weather full thickness removed or part there of) complete all as specified and as directed by engineer-in-charge.

Dismantling of brick tiles or terracing tiles laid bedded and pointed in cement mortar in single layer on roofs complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly concrete surface making surface completely dry and apply APP modified prefabricated water proofing membrane 3mm thick super therolay of STP limited with non woven polystermale reinforcement of 160gm, weighing not less than 3.6kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene (MHHDPE) film consisting of five layers laid with torching application to the surface. the end lap should be 100mm and the side lap must be minimum 75mm. The membrane shall be first laid upto the parapet wall junction and then shall be overlapped with another membrane (flashing) with and overlap covering upto a distance of 300mm. In case of parapet height is less than/upto 500 mm membrane shall be terminated at the top of parapet complete all as specified and directed by Engineer-in-charge.

M&L for 40mm thick brick tiles laid on 15mm screed bed in cement mortar 1:6 with jointing and pointing in cement mortar (1:3) mixed with 5% crude oil by weight of cement complete all as specified and directed by Engineer-in-charge.

All as per item no 105 above but except brick tiles complete all as specified and directed by Engineer-in-charge.

S&F 110 mm PVC (SWR) pipes class 'A' single socketed in any length with rubber ring joints fixed to walls complete all as directed by Engineer-in-Charge.

S&F 110 mm PVC (SWR) bend complete all as directed by Engineer-in-Charge.

Taking down rain water pipes (any size or pattern), including all fittings etc complete all as specified & directed.

Material & labour for 50mm thick PCC (1:3:6) type C-1 ( using 20mm graded stone aggregate) as in plinth protections and path etc finishing the concrete surfaces even and smooth without using extra cement & joint filled with bitumen sand mixer 50mm thick complete all as specified and directed.

Forming contraction joints 30mm deep x 10mm wide and filled with sealing compound grade A complete all as specified and directed.

M&L for framed work such as grills/gratings etc with ends of bars shouldered and or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framed work of water tanks and similar work conforming to Fe-290, Gde E-165 all as specified and directed.

Material & labour for 18-20mm thick machine cut kota stone slab laid in floors, slabs and steps etc jointed with grey cement slurry mixed with pigments to match the shade of the slab including cutting, rubbung and polishing over and including screed bed 20mm thick in cement mortar (1:6) complete all as specified and directed. Note - Kota stone for step shall be in single piece.

Material & labour for 20-25mm thick machine cut kota stone slab as in vertical surfaces such as dado/ skirting/pillars/risers of stair case etc jointed with grey cement slurry mixed with pigments to match the shade of the slab including cutting, rubbuing and polishing over and including rendering 15mm thick in cement mortar (1:4) complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

Material & labour for welding in repair exc.2.5 cm but n exc. 5 cm in length for thickness of metal exc.6 mm but not exc.9 mm complete all as specified.

S&F in repair box type hinges of any size including necessary welding to existing window/vent complete all as specified and directed by Engineer-in-charge.

Supply & fix in repair 40 mm dia cupboard knobs of brass duly polished, with nuts, screw and washer of mild steel bright finished complete all as specified.

Supply & fix in repair 150 mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply & fix 150 mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair magnetic type catch fixed with screws to door frame complete all as specified and directed by Engineer-in-charge.

S&F floor door stopper aluminium alloy body and tongue 140mm anodised with hard drawn steel spring etc complete all as specified and as directed by engineer-in-charge.

S&F in repair floor door stopper aluminium alloy body and tongue 140mm anodised with hard drawn steel spring etc complete all as specified and as directed by engineer-in-charge.

Supply only 32 mm bore PVC waste coupling (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) with PVC waste pipe for WHB complete all as specified and as directed.

Supply only 40 mm bore PVC waste coupling (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) with PVC waste pipe for sink complete all as specified and as directed.

Supply & fix 250 mm long aluminum anodized sliding door bolt, plate type with bright bolt not less than 12 mm dia with hasp, staple (bolt type) and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

Material & labour for 50mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in fillings, mass concrete as in roof padding etc complete all as specified and directed.

Supply and fix mild steel bright finish or electrogalvanised 40mm width of flap continuous (piano) hinges fixed with screws complete all as specified and directed.

Supply only 32mm bore PVC waste pipe complete all as specified and directed.

Supply only 40mm bore PVC waste pipe complete all as specified and directed.

Taking down carefully existing point wiring of any type (i.e. wooden surface conduit casing capping or concealed conduit) complete for light or fan or socket or power etc on wooden batten or in conduit including fittings and accessories like switches, sockets, wooden board and making good disturbed portion to match with existing complete all as specified and directed.

Material & labour for concealed point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated and unsheathed cable 1100 volts multistranded, copper conductor cable (FRLS) drawn through and including PVC concealed conduit not less than 20mm dia bore medium grade (ISI marked) and accessories like bends, tees, junction boxes etc, fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS, copper multistranded cable as earth wire including sunken pressed steel terminal boxes and bakelite white/ coloured top sheet cover 3.0 mm thick , for One light point / fan point / call bell point controlled by one way switch complete all as specified and directed.

All as per srl item No 132 here-in-before but 3 pin socket outlet, 5 Amps on independent board complete all as specified and as directed

All as per srl item No 132 here-in-before but for 3 pin socket outlet, 5 Amps on same board with other switches complete all as specified and as directed

All as per srl item No. 132 above but one light point controlled by two 2-way switches complete all as specified.

All as per description of srl item No 129 here in before but using 4 sqmm (nominal area) PVC unsheathed cable independent including PVC cable copper conductor with 4 Sqmm PVC insulated copper cable for continuous earth continuity conductor and connecting for earth dolly for 5 pin socket out let 15 Amps on independent board. complete all as specified and directed.

S&F switch piano flush type 5 amp single pole one way complete all as specified and directed.

S&F switch piano flush type 15 amp single pole one way complete all as specified and directed.

S&F bell push flush type single pole one way 5 amp complete all as specified and directed.

Supply and fix socket out let multi purpose 2 in one, 3 pin, 5 amps flush type complete all as specified.

Supply and fix socket out let multi purpose 2 in one, 3 pin, 15 amps flush type complete all as specified.

S&F switch piano flush type 5 amp single pole two way 5 amp complete all as specified and directed.

Supply and fix in repair ceiling rose surface type bakelite 65 x 50 mm three terminal PVC / Polycarbonate isolated body complete all as specified.

S&F call bell multi music type single pole, AC 240 volt complete all as specified and directed

Taking down old u/s fluorescent tube light fitting and Supply, installation, testing and commissioning of 20 watt 4 ft long LED batten housing made of self ballasted LED batten extruded aluminium with PC diffuser integral isolated driver > 120 degree wide light distribution and lumen output should be at least 1800 lumen with a CCT of 6500K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed. complete all as specified and directed. Make:Polycab Cat Part No LD00103023 LED or equivalent makes as mentioned in grp 1 of Appx 'B'

Taking down unserviceable MCBs and supply and fixing MCB 6 to 32 amps, SP 240 volts, complete all as specified and directed.

Taking down unserviceable MCBs and supply and fixing MCB 6 to 32 amps, SPN 240 volts, complete all as specified and directed.

Taking down old unserviceable sub main wiring 4.00/6.00 Sqmm 1100 volts grade 2/3 runs of single core PVC insulated, unsheathed copper conductor including taking down casing/caping/PVC conduit and making good the surface complete all as specified and directed.

Supply and fixing sub main wiring with two single core PVC insulated cable with copper conductor stranded and sheathed of size 6 sqmm, two runs in and including PVC concealed conduct medium grade of size not less than 25mm dia including PVC accessories complete incl cutting and chasing and making good etc incl one run of 6 sqmm PVC insulated unsheathed multi stranded copper conductor cable to common earth and connected to earth dolly complete all as specified and directed. Note : Two run of 6 sqmm cable & one run of 6 sqmm including PVC conduit 25mm will be measured as one unit.

Taking down old unserviceable wall mounting fitting and Supply & fix decorative wall mounting type made up of polycarbonate rings , and glass shade with lamp holders, connectors block, 1x15 watt LED bulb , glass fitted engineering plastic B22 d lamp holder with electrical copper contacts, self screwed polycarbonate diffuser in opal finish for soothing light effect, LED 15 watt etc complete with all accessories prewired and including connecting up with three core flexible copper conductor cable complete all as specified and directed.Make : Havells Cat part No. LHDL02160099 or equivalent as mentioned in grp 1 of Appx 'B' complete all as specified and directed.

Taking down old unserviceable bulk head fitting and Supply & fix bulkhead fitting decorative ceiling/wall mounted bulk head with engineering plastic housing and top frame with opal PMMA diffuser suitable for 1 x 06 watt LED bulb including 1 No 06 watt LED complete all as specified and directed.Make: Cat part No. CG80IB6WLED of C&S electric or equivalent as mentioned in grp 1 of Appx 'B' .

Taking down old u/s regulator and S&F electronic type fan regulator 5 step, 80W, 240 V, 50Hz, AC on existing phenolic laminated sheet etc. suitable for ceiling fan complete all as specified and directed.

Taking down old unsv DB and S&F factory made sheet metal enclosure double door distribution board class IP-43 with 200 amp rated copper bus bar 240 V, 8 way single pole and neutral link and earth plug with & incl metal ply & one SP MCB 20 amps complete all as specified and directed.

S&F ventilating fans of plastic body having 150mm sweep, 230 volts self closing louvers, ideal for mounting on teakwood & glass complete all as specified and directed.

S&Ftriple pole and neutral double door distribution board 4 way vertical type class IP-43 with 200 amp rated copper bus bar 240 V suitable for mounting MCCB, complete all as specified and directed.

S&Fin replacement MCCB 4 pole, 100 amps, 16 KA breaking capacity, 415 volts, AC 50 Hz with overload and thermal tripping features complete all as specified and directed.

Taking down of old LT panel with accessories including electric energy meter and Supply, installation, testing and commissioning of LT panel size 450mmx450mmx150mm enclosures cubical weather and vermin proof totally enclosed made out of not less than 1.6 mm thick CRCA sheet machine pressed of suitable size to operate on 3 phase 4 wire system 415 volts, 50Hz double door with front openable and PVC acrylic glass cover of suitable size for checking of meter reading without opening door with locking arrangement incuding inner shutters for mounting switch gear etc suitable arrangement for fixing of electrical meter and SPN 40 to 63 amp including pre wiring from bus bar to meter and meter to MCB SPN (for pre wiring use 6.00 sqmm single core copper cable and suitable size of lugs for connecting from bus bar to meter and meter to MCB SPN ) including bottom gland plate with sufficient numbers of circular cable entry holes, including pre wired complete as per drg with masonry work for fixing in wall duly powder coated with comprising of following INCOMING :- (i) MCB 32 to 40 amps, 230 volts, 10 KA single pole and neutral =02 No (ii) S&F single phase electronic energy meter with LCD display of rating 5-30 amp class 1, 240V 50Hz counter type display with transparent hinge including connection from SPN to meter with 6 sqmm copper stranded conductor including earth wire complete all as specified and directed by Engr-in-charge.

S&F distribution board single pole and neutral 12 way 240 V, double door type suitable for mounting incomming and outgoing MCBs single/double pole, 8/4 Nos rescpectively complete all as specified and directed. Note : MCB SP/SPN ill me measured and paid separately

Taking down old unserviceable GI pipe and Supply & fixing 40mm dia GI tubing medium grade complete with all fittinggs (ISI Marked) laid in trenches/fixed to wall and ceiling or laid in floor complete all as specified and directed.

Taking out old UG cable and Supply and lay cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric cable heavy duty electric cable with aluminium conductor of size 25 sqmm 3.5 core , 1100 volts grade, complete all as specified and directed.

M&L for excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth in soft/loose soil for laying of cable/GI pipe and getting out complete all as specified and directed.

Returning filling in including spreading,levelling,watering, well ramming in layers not exc 25 cm each complete all as specified and directed.

Removal of surplus soil to a distance not exc 50 m and deposited where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Supply and spread river sand in trenches as cable cushioning 8 cm below the cables and 15 cm above the cables all as directed and directed Note : Punned down thickness shall be measured.

Material & labour for old size sub class ‘B’ bricks laid flat in trenches over the cable with the length of brick perpendicular to the direction of cable length, adjacent/abutting each other complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continuous earth wire on pole, testing the earthing after completion complete all as specified and directed. Note :- (I) Earth pit shall be constructed 50cm from the side of excavation to avoid sinking of pit (II) PCC chamber shall be (1:3:6) using 20mm graded stone aggregate and 50mm thick RCC (1:2:4) type B-1 cover slab reinforced with 8mm dia TMT steel bars @ 100mm c/c both ways complete all as specified and directed. .

VISHWAMITRA CONSTRUCTIONS

COSMO BUILDERS

Gurjit const co