Loading
Loading…
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
Refer Docs
EMD Value
₹17.8 L
Closing Date
23 Sept 2025, 8:30 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Karnataka Power Transmission Corporation Limited
Muniraju.P
Establishing 2x20MVA, 110/11kV Sub-Station at Chitta (Goranahalli) along with Construction of 110kV LILO line using Lynx conductor from existing 110kV Kamthana - Habsikote line to proposed 110kV Chitta (Goranahalli) Sub-station for a distance of 1.258kms in Bidar taluk & District on Partial TurnKey basis including supply of all matching materials equipments (Excluding supply of 11 kV Switchgears) and erection (including civil works) of all materials equipments, testing and commissioning.
KPTCL/2025-26/SS/WORK_INDENT2572
KPTCL/2025-26/SS/WORK_INDENT2572
Open
Sub-Station
Two Tender Document System(Two Cover)
KPTCL CEE Corporate Office Tendering and Procurement Bengaluru
20 documents required · 20 mandatory
Documentary proof for Clause No. 3.2(b)(i) of ITT such as P.O, LOI/LOA, DWA, Work done Certificates, Performance Certificates issued by the end users not below the rank of Executive/Divisional Engineer.
Documentary proof for Clause No. 3.2(b)(ii) of ITT such as P.O, LOI/LOA, DWA, Work done Certificates, Performance Certificates issued by the end users not below the rank of Executive/Divisional Engineer
Cl.No.3.2(d)(A) Qualifying Requirements for Power Transformer manufacturer as a Bidder: Shall upload Necessary documentary evidence for Cl.No 3(b) &(c) of Cl.No.3.2(d)(A) issued from Utilities such as P.O. copies, LOA/DWA, Performance Certificates issued by the end users (Indian Government Power Utilities) not below the rank of Executive/Divisional Engineer, should be uploaded along with the offer
Audited financial statements including Balance sheets, Profit and Loss statements, Turnover Certificate, Auditors Reports of the last five years preceding the date of bid submission of the Bidder & Consortium member (In case of Consortium)
Cl.No.3.2(d)(A)Qualifying Requirements for Power Transformer manufacturer as a Bidder: The manufacturer of Power Transformer must be registered under Indian Company Act 1956/2013 / The Indian Factories Act 1948/Any relevant Indian Laws, whichever is applicable
Cl.No.3.2(d)(A)Qualifying Requirements for Power Transformer manufacturer as a Bidder: The manufacturer of Power Transformer shall furnish Type Test reports of not older than five years as on the date of bid submission as per Cl.No 3(d) & (e) of Cl.No.3.2(d)(A)
Cl.No.3.2(d)(A)Qualifying Requirements for Power Transformer manufacturer as a Bidder: The manufacturer of Power Transformer shall furnish Dynamic Short circuit test reports for Power Transformers as per Cl.No 3(f) of Cl.No.3.2(d)(A)
Cl.No.3.2(d)(A)Qualifying Requirements for Power Transformer manufacturer as a Bidder: In case, the manufacturer has not conducted dynamic short circuit test earlier or if there is change in design, then, in the event of Award, the Bidder shall furnish Dynamic Short Circuit Test Report for the Transformer, the design of which is similar to the offered transformer as per IS/IEC standards conducted at designated laboratories as mentioned in KPTCL Technical Specifications without affecting the Delivery Schedule and at no extra cost to KPTCL. In this regard, the Bidder shall upload an undertaking agreeing to the same (Refer Undertaking-1 of the tender documents) as per Cl.No 3(f) of Cl.No.3.2(d)(A).
Documentary proof for Clause No: 3.6 of ITT: Assessed available tender capacity such as, Statements showing the value of existing commitments and on-going works as well as the stipulated period of completion remaining for each of the works listed countersigned by the Employer in charge, not below the rank of an Executive Engineer or equivalent or verified and certified by Chartered Accountant/Cost Auditor as sought in Note of the said clause in the prescribed format as in clause No: 1.5 of Qualification Information by the lead Bidder and Consortium member(In case of Consortium).
The Tenderer shall upload Bankers Certificate of lead Bidder & Consortium Partner (if applicable) duly signed by authorized person in the prescribed format as at Annexure XVIII of Section-4 and as per the clause no.3.3 (b) of ITT (Liquid Assets and /or availability of credit facilities)
Self-declaration as sought in Clause No. 3.6 Note (ii) of ITT by the Lead Bidder & Consortium partner(in case of Consortium) stating that the information with regard to assessed available tender capacity (Works on Hand) furnished are correct.
Certificate from Chartered Accountants for split details of financial Turnover and GST in the prescribed format (Annexure-XX) of Lead Bidder & Consortium partner (In case of Consortium).
Self-declarations of Lead Bidder & Consortium partner (In case of Consortium) in respect of Litigation, dis-qualification due to non-performance, Risk & cost clause and Restriction on border sharing as specified in Annexure- XVI& Annexure-XVII as per Clause No.2.4of ITT
Consortium Agreement(in case of Consortium)
Power of Attorney in favour of all the persons signing the documents, Power of Attorney for Consortium(in case of Consortium), combined power of attorney signed by the signatories of all the members of consortium as an evidence of authorization for nominating leader (Prime Bidder) of consortium.( in case of Consortium)
Valid Super Grade Electrical Contractors License of both Lead Bidder & Consortium partner (in case of Consortium) issued by the Govt. of Karnataka
Certificate of Incorporation of the Individual/Consortium or any relevant document in respect of Partnership/Proprietorship firms as per the tender document
The bidder and Consortium Partner(in case of Consortium) should have valid GST registration with GSTIN number PAN Card and ISO Certificates. Note The successful Bidder and his consortium partner who have GST registration in other States should have GST registration in the State of Karnataka mandatorily at the time of execution of the Contract Agreement.
No Deviation Certificate
Letter of Undertaking as in Annexure
undertaking to source the supply of equipment/material from KPTCL approved Vendors only as per the QR for Vendor registration, available in the KPTCL website i.e., https://kptcl.karnataka.gov.in, Link Tender and Procurement - application for Vendor registration etc.
Description of the Tools & Plant available with them for execution of the Work
undertaking to source the supply of equipment/material from KPTCL approved Vendors only as per the QR for Vendor registration, available in the KPTCL website i.e., https://kptcl.karnataka.gov.in, Link Tender and Procurement - application for Vendor registration etc.
undertaking to source the supply of equipment/material from Vendors who meet the eligibility clauses regarding restriction on procurement from a country which shares land border with India as specified in Annexure- XVII.
Details of Works on hand and Ongoing contractual commitments
Upload all relevant documents as per Section-3 Qualifying information, NIT, Terms & conditions as stipulated in the Tender Document.
Copies of original documents defining the Constitution or Legal Status, place of Registration and Principal place of Business of the Bidder (Lead Bidder & Consortium Partner) , written Power of Attorney to the Signatory of the Bid to commit the Bidder (Lead Bidder & Consortium Partner) to the Contract along with the resolution passed in this regard by the Board of Directors all the Partners of the Firm.
The Tenderer shall upload declarations for Deviations, if any as per Schedule-5 and Schedule-6 of the Techno Commercial sheets
Please note that the Filled in Techno commercial sheet shall be uploaded along with all other QR documents. Offers shall be quoted in the item-wise bid Financial offer, provisioned in the e-procurement portal. In case the Prices are uploaded in/along the Techno commercial Bid, then Bid will be summarily rejected. The Techno-commercial sheets shall be uploaded in KPTCL excel formats only.
Any other documents as specified in the tender,
₹7,500
₹17.8 L
8 Sept 2025
8 Sept 2025
24 Sept 2025
8 Sept 2025
8 Sept 2025
Power Transformer:
20 MVA, 110/33-11kV, Delta/Star, Dyn11, 3-Ph, 50Hz, Core Type, 2 Winding Delta/Star transformer, vector group DYn11 with OLTC ONAN/ONAF with fan control cubicle, RTCC Panel, first...
Supply, Erection & Commissioning of Nitrogen Injection Fire Extinguishing System for Power Transformer below 100 MVA as per technical specifications
Circuit Breaker :
SF6 Gas circuit breaker with Semi-Pneumatic / Pneumatic operated / Spring type operating mechanism, including mounting Structures arrangements with rigid, bi-metallic terminal conn...
Isolators : Double break manually operated isloators with solid core insulator, terminal connector suitable for Al. tube /conductor (Moose ACSR/75mm/63mm), marshalling box etc., complete as per techn...
ii.Upright mounting type without earth switch(Live point height 6350mm)
Note:Terminal connectors for Isolators shall be as follows:
Rigid type suitable for Moose ACSR- 27Nos)
Flexible type suitable fo...
B. 11 kV Isolators:
11KV isolators, Double Break 400A, 25KA capacity with rigid bi-metallic terminal connectors suitable for Coyote ACSR for Capacitor Bank
11 kV isolator, single break 400 A, 25 KA capacity with Roaster switch, with rigid bimetallic terminal connector suitable for coyote ACSR.
CURRENT TRANSFORMER : Current transformers including marshalling boxes, Single phase,oil filled outdoor type with rigid bimetallic terminal connectors suitable for Moose ACSR conductor as per technica...
2)110 kV class, 40 KA, CT of ratio 400-200/ 1-1-1A for Lines
Core - 1 : Vk-800 V at 400A, Rct 5 ohm at 400/1A, Accuracy class PS-Dist/Dif
Core- 2 : 10 VA, Accuracy class 0.2s- Metering
3)11kV Class, 25kA, NCT of ratio 1200-800/1-1-1A for REFR Protection (of similar rating and ratio as that of Incomer of 11kV Switchgear) with terminal connector suitable for 2 Nos. of 75mmx6mm Copper ...
VOLTAGE TRANSFORMER : Single phase, oil filled outdoor type with rigid bimetallic terminal connectors suitable for Moose ACSR with marshalling box KIOSK as per technical specifications
110 kV class 1...
SURGE ARRESTOR : (Porcelain housing) metal oxide, Gapless type with rigid bimetallic connectors suitable for Moose ACSR as per technical specifications
i. 96 kV, 10 KA, SM type -For overhead Lines
ii. 96 kV, 10 KA, SM type-For Transformers
iii.9 kV, 10 KA with connector and clamp
Capacitor Bank: Design, Engineering, supply, erection, testing & commissioning of 2.9 MVAR, 12.1 kV Capacitor Bank, star connected, Double Bank with internal fuses, terminal connectors with suitable n...
Control and Relay Panel complete as per specifications:
Simplex type control and relay panels complete as per specifications.
a.For Power Transformer 110/11 kV
b.For 110 kV Transmission line
1) All the C&R panels and associated panels shall be of one and same make for uniformity and interchangeability of components.
2) The accuracy class of metering ...
Total Weight of Station structures & Mounting Structures (excluding Bolts & nuts)
Note:(i)For Split up refer Techno-Commercial sheet
(ii)Rate shall be quoted on per tonne basis
Total Weight of Bolts & nuts of Station structures & Mounting Structures
Note:(i)For Split up refer Techno-Commercial sheet
(ii)Rate shall be quoted on per tonne basis
11 kV ODS and take off structure:
Supplying of Double pole structure with 9.5 Mts. RCC poles WL 300 Kgs for mounting 11 kV 400 A Roaster Isolators and 9 kV, 10 KA surge arrestor (3 No.) complete set ...
BUS BAR FORMATION:
Rigid bus with taps & clamps
i) Aluminium pipe conforming to 6340WP of IS - 5082 / 1969 (BS I600-Sch. 40) of following nominal diameter a) 75mm
b) 63mm size connecting isolator to vertical tap
ii) Straight taps suitable for 63mm Aluminium tube (BS-1600) of 1750mm vertical height for vertical portion & cross bus on 110KV side with rounded off end.
iii) A) Post insulator clamps suitable for 75 mm Aluminium pipe & Post insulator solid core type - 110kV side
c)Expansion Type
v) Corona Bell Suitable for Aluminium Pipe of size 75mm on 110 kV
vi) End cap sutable for AL tube of size 63 mm on 110KV
(i)Solid core Bus Post insulator Insulator 110kV, 1Unit/stack
i)C Type wedge connector suitable for Moose - Lynx (Line)
ii)Post insulator clamp suitable for Moose ACSR and 110kV Solid core insulator.
Auxiliary Transformer :
i)Supply of Auxiliary Transformer with copper windings and oil, cable termination type on both HT & LT outdoor type, 100 kVA, 11 kV/433 V, 3 Ph, Vector group Dyn 11 off load...
ii)Supplying of DP structure with 9.5 mtr RCC poles, 11 kV 400 A double break isolators, 9 kV, 10 KA surge arrestor (3 No.), H-Frame along with DOLO/HG fuse unit, LTprotection kit/LTD box, LT Trivect...
LTAC Distribution panel (Indoor),415V as per technical specification comprising of Voltmeter, Ammeter,1 I/C MCCB 200A + 2 nos. 3 Phase 63A O/G SFU +2 nos. 3 Phase 32A O/G SFU 100A + 14 O/G SFU, 6 nos....
AC Distribution box (outdoor) Single front type with 6 terminals 1200 x 1350 x 300 mm one I/C of 100 A MCCB 20 KA+ 6 O/G 16 A MCB +1 O/G of 100 A HRC Fuse panel 415 V outdoor type complete as
LT Power armoured UG cable with glands/lugs/ferrules as per specification:
a) 1.1 kV class 4 X 95 Sq mm L T Aluminium Cable
b) 1.1 kV class 4 X 25 Sq mm Copper Cable
c) 1.1 kV class 4 X 10 Sq mm Copper Cable
STATION BATTERY & BATTERY CHARGER :
110V, 200AH Battery set (Plante/Grid/Nickel Cadmium Type) with accessories as per specification
Battery charger- suitable for '1 X 110 V, 200 AH, Battery set (Plante/Grid/Nickel Cadmium Type)15 A float and 30 A boost (with float and boost battery charger as per technical specification)
LT DC Distribution panel ( Indoor) as per Technical specification comprising of Earth fault indicator, Indication circuit for AC main failure, 1 No 100A SFU for IC + 12 nos., 32A SFU for OG etc, compl...
1.1 kV Grade PVC Insulated armoured copper control cables of sizes,with Lugs/Ferrules/Gland as per technical specifications.
19C x 2.5 Sq.mm
10C x 2.5 Sq.mm
(For station Yard Lighting -1000Mtrs)
11KV U.G. Cable with the required cable terminations at both ends as per specifications.
(i)One run of 11kV, XLPE 95 sq.mm Al., 3 core cable - (to be run for Auxiliary Transformers from 11KV switch...
ii)11KV XLPE cable, 1000Sq. mm. Aluminium cable from 110/11KV transformers to 11KV Switchgear
iii)11KV XLPE cable, 240Sq. mm. Aluminium cable 3 Core to be run from 11KV Switchgear to 11kV take off DP Structure
iv)Heat shrinkable type Cable termination kits suitable for 1 x 1000 Sq.mm XLPE cable ( Indoor type )
v)Heat shrinkable type Cable termination kits suitable for 1 x 1000 Sq.mm XLPE cable (Out door type)
vi)Heat shrinkable type Cable termination kits suitable for 3 x 240 Sq.mm XLPE cable ( Indoor type )
vii)Heat shrinkable type Cable termination kits suitable for 3 x 240 Sq.mm XLPE cable (Out door type)
viii)Heat shrinkable type Cable termination kits suitable for 3 x 95 Sq.mm XLPE cable ( Indoor type )
ix)Heat shrinkable type Cable termination kits suitable for 3 x 95 Sq.mm XLPE cable (Out door type)
FIRE FIGHTING EQUIPMENTS WITH NECESSARY MOUNTING STANDS:
Foam type extinguisher (Mechanical) 50 Ltr. capacity
Foam type extinguisher (Mechanical) 9 Ltr. capacity
Water type (gas pressure type) 9 Ltr. capacity
Carbon di-oxide type 4.5 kg Capacity
Sand type G.I Buckets 15 Ltr. Capacity
Steel stands for above to have 4 buckets to each stand.
Maintenance Tools and Plant:
Portable (mobile) oil pumps (1/2 HP Air pump 500 to 1000 gallons)
Telescopic ladder Aluminium 6 Mtr. Height
Ring spanner set
Tube spanner set
Pipe wrench 24 inch
Pipe wrench 18 inch.
Hydraulic crimping tools up to 1000 Sq.mm
Rubber hand gloves (15 kV tested)
Rechargeable 5W LED hand torch
Insulated cutting plier 12 inch size
Insulated cutting plier 8 inch size
Line live tester AC/DC 500 V
Screw driver 18"
Screw driver 12"
Chain pulley block 5 ton capacity
Hydraulic jack 5T capacity
Pipe derrick suitable for lifting 3 MT and lift of 6 Mtr. Height
Transil oil di-electric break down (with 2.5 mm gap 0-60 kV) Tester.
Insulation megger 2.5 - 5 kV
Insulation megger 500 V
SF-6 gas leak Detector
Multimeter electromechanical
Multimeter Electronic
DC Voltmeter range -5V to + 5V
Hydrometer syring suitable for vent holes
Specific gravity correction chart
Thermometer with wall mounting holder
Protective goggle
Acid resisting jars (4 pint capacity)
Rubber shoes knee height
Grounding sticks extendable upto 18 ft
Wall mounting type holder for hydrometer
MISCELLANOUS ITEMS
Rubber mats 1000 mm x 1000 mm x 10 mm size
Shock treatment charts, hard board, liminated with coloured pictures & literature both in Kannada & English.
Water filter / Water purifier : Wall mounting type (Aqua-guard type).
Sub-station name board duly painted.
Fixograph of size 1.5m x 2.5m with English / Kannada alphabets.
Door locks 7 Levers-Reputed & Approved Quality
Danger board(prohibited) with support structure including fixing in front of the gate
Equipment name plates and earthing name plates including fixing at outdoor yard
Furniture for Control Room Staff and maintenance staff
i.Steel Almirahs 6 1/2 feet
ii.Steel Almirahs 6 1/2 feet with glass panel doors
iii.Officers tables
iv.Steel Slotted angle rack (big Size)
v.Steel Slotted angle rack (small Size)
vi.Steel dustbins
vii.Executive revolving chairs
viii.‘S’ Type Arm Chairs
ix.Steel folding Chairs
Equipments for establishing SCADA Communication :
Note:1.Satellite Communication required will be arranged by SLDC
i.Remote Terminal Unit (RTU) 64 (I/O) Port
ii.Data Concentrator Unit (DCU)
iii.2 kVA online UPS (230 V AC 1 phase 50 Hz) with Battery set confirming to KPTCL specification
i.Current Cables-Copper Core with c/s 4.0 sq.mm Multistrand 4 Core
ii.Voltage Cables-Copper Core with c/s 2.5 sq.mm Multistrand 4 Core
iii.Signal Cables-armoured Copper Core with c/s 0.5 sq.mm Multi strand 10 Core
iv.Control Cables- Copper Core with c/s 1.5 sq.mm Multi strand 10 Core
v.Supply Cables-Copper Core with c/s 4.0 sq.mm Multi strand 3 Core for AC input to UPS & UPS to RTU, conforming to KPTCL specifications.
vi.Supply Cables-Copper Core with c/s 32.0 sq.mm Multi strand for Battery conforming to KPTCL specifications.
STATION & YARD LIGHTING (OUTDOOR) (To be designed, assessed & quoted by the bidder):
Supply and installation/ Fixing/ Provision of Outdoortype Thermoplastic Modular Panel enclosure with transpare...
Supply & Fixing of LED Street light luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection mou...
Station Erection
Power Transformer:
20 MVA, 110/33-11kV, Delta/Star, Dyn11, 3-Ph, 50Hz, Core Type, 2 Winding Delta/Star transformer, vector group DYn11 with OLTC ONAN/ONAF with fan control cubicle, RTCC Panel, first...
Circuit Breaker :
SF6 Gas circuit breaker with Semi-Pneumatic / Pneumatic operated / Spring type operating mechanism, including mounting Structures arrangements with rigid, bi-metallic terminal conn...
Isolators : Isolators including marshalling box and suitable terminal connectors as per technical specification with solid core cylindrical post insulators:
A. 110KV, 1250A, 40KA Class Double Break Ma...
B) 11 kV Isolators
i) 11KV isolators, Double Break 400A, 25KA capacity with rigid bi-metallic terminal connectors suitable for coyote ACSR for Capacitor Bank-4 Nos.
ii) 11 kV isolator, single break 40...
CURRENT TRANSFORMER : Current transformers including marshalling boxes, Single phase,oil filled outdoor type with rigid bimetallic terminal connectors suitable for Moose ACSR conductor
i) 110 kV class...
ii) 11kV Class, 25kA, NCT of ratio 1200-800/1-1-1A for REFR Protection (of similar rating and ratio as that of Incomer of 11kV Switchgear) with terminal connector suitable for 2 Nos. of 75mmx6mm Coppe...
VOLTAGE TRANSFORMER : Single phase, oil filled outdoor type with rigid bimetallic terminal connectors suitable for Moose ACSR with marshalling box KIOSK as per technical specifications
110 kV class 1...
SURGE ARRESTOR : (Porcelain housing) metal oxide, Gapless type with rigid bimetallic connectors suitable for Moose ACSR.
i) 96 kV, 10 KA, SM type -For overhead Lines -6Nos
ii)96 kV, 10 KA, SM type-For...
iii)9 kV, 10 KA with connector and clamp
Control and Relay Panel complete: Simplex type control and relay panels complete as per specifications.
i) For Power Transformer 110/11 kV-02Nos
ii)For 110 kV Transmission line-02Nos
Total Weight of Station structures & Mounting Structures including Bolts & nuts.
Note: (i)For Split up refere Techno-Commercial sheet.
(ii) Rate to be quoted on per t Basis.
11 kV ODS and take off structure
Erection of Double pole structure with 9.5 Mts. RCC poles WL 300 Kgs for mounting 11 kV 400 A Roaster Isolators and 9 kV, 10 KA surge arrestor (3 No.) complete set .
BUS BAR FORMATION :
Main bus/cross bus (all the three phases in a segment) using with Single Moose/Drake Conductor with fixing of insulator spacers, levelling of string conductors to the required heig...
Rigid bus with taps & clamps
Aluminium pipe conforming to 6340WP of IS - 5082 / 1969 (BS I600-Sch. 40) inlcuding fixing of clamp, connector jumper ,corona ring etc., complete & as per technical speci...
Post insulator Solid core Insulator 110 kV, 1 Unit/stack
Auxiliary Transformer
Erection of Station Auxiliary Transformer-copper winding with oil, outdoor type, 100 kVA, 11 kV/433 V, 3 Ph, Vector group Dyn 11 off load tap changer(5 taps) with step volta...
Erection of DP structure with 9.5 mtr RCC poles, 11 kV 400 A double break isolators, 9 kV, 10 KA surge arrestor (3 No.), H-Frame along with DOLO/HG fuse unit, LTprotection kit/LTD box, LT Trivector me...
LTAC Distribution panel (Indoor),415V as per technical specification comprising of Voltmeter, Ammeter,1 I/C MCCB 200A + 2 nos. 3 Phase 63A O/G SFU +2 nos. 3 Phase 32A O/G SFU 100A + 14 O/G SFU, 6 nos....
AC Distribution box (outdoor) Single front type with 6 terminals 1200 x 1350 x 300 mm one I/C of 100 A MCCB 20 KA+ 6 O/G 16 A MCB +1 O/G of 100 A HRC Fuse panel 415 V outdoor type complete as per ...
LT Power armoured UG cable as per specification
i) 1.1 kV class 4 X 95 Sq mm L T Aluminium Cable with glands/lugs/ferrules- 200mtrs
ii)1.1 kV class 4 X 25 Sq mm Copper Cable with glands/lugs/ferrule...
STATION BATTERY & BATTERY CHARGER :
110V, 200AH Battery set (Plante/Grid/Nickel Cadmium Type) with cells & accessories as per technical specifications
Battery charger- suitable for '1 X 110 V, 200 AH, Battery set (Plante/Grid/Nickel Cadmium Type)consisting cells as per specifications- 15 A float and 30 A boost (with float and boost battery charger ...
LT DC Distribution panel ( Indoor) as per Technical specification comprising of Earth fault indicator, Indication circuit for AC main failure, 1 No 100A SFU for IC + 12 nos., 32A SFU for OG etc,. comp...
1.1 kV Grade PVC Insulated armoured copper control cables of sizes,with Lugs/Ferrules/Gland as per technical specifications
i) 19C x 2.5 Sq.mm-1900mtrs
ii) 10C x 2.5 Sq.mm-1500mtrs
iii) 4C x 6 Sq.mm-2...
11kV Switchgear
11kV, 25kA, Metal Clad VCB Switchgear (1600A for Incomer and 1250A for feeders), outdoor type, each comprising of 2IC+12F+1BC+4CB+1AP (Remote Announciation cum Control panel) with CTs...
11KV U.G. Cable with the required cable terminations at both ends.
i) One run of 11kV, XLPE 95 sq.mm Al., 3 core cable - (to be run for Auxiliary Transformers from 11KV switch Gear to Auxiliary Tra...
A.Heat shrinkable type Cable termination kits suitable for 1 x 1000 Sq.mm XLPE cable:
a.Indoor type - 14Nos.
b.Out door type-14Nos
B.Heat shrinkable type Cable termination kits suitable for 3 x 240 Sq.mm XLPE cable ( Indoor type )
a.Indoor type - 15Nos.
b.Out door type-15Nos.
C.Heat shrinkable type Cable termination kits suitable...
Equipments for establishing SCADA Communication as per technical speciifcations :
i. Remote Terminal Unit (RTU)
ii. Data Concentrator Unit (DCU)
iii. 2 kVA online UPS (230 V AC 1 phase 50 Hz) with Battery set
iv.Integration of RTU, DCU and UPS with field equipments
v.Control Cables - Laying
a.Current Cables-Copper Core with c/s 4.0 sq.mm Multistrand 4 Core- 40mtrs.
b.Voltage Cables-Copper Core with c/s 2.5 sq.mm Multistrand 4 Core-20mtrs
c.Signal Cables-armour...
Earth Mat formation :
Supplying and laying MS.Flat 75 x 12 mm flat welding and applying ACB paint to welded portion and covering with Sodium Bentonite Clay (SBC supplied by Corporation) as per drawing...
Grounding of equipments with 75 x 12 mm G I flat and connecting equipments to the earth mat/ground pit including all connected works with all materials supplied by the contractor.
Providing 40mm dia, 1.075mtr. long Earthmat Spike of MS Rod including bending top 50mm etc
Providing C.I. Pipe of 100mm ID 13mm thick 2.75 mtr. long with 2 part GI Flat 50x6 mm clamp welded allround the pipe etc., including cost of excavation (all materials supplied by contractor)
Supplying and fixing 450mm dia x 450mm height 1.5" to 2" Hume pipe collars for earth pits.
Providing deep bore earthing: Sinking bore of 150mm clear dia using fast rig including fixing of 40mm dia MS rod, including jointing the pipes as per KPTCL standards & providing sodium bentonite treat...
40mm dia MS rod (5 mtr) (50x5)
Bentonite clay (50x5x9)
Cost of GI flat for joining two rods by welding to obtain continuous length. (50x5/10)
Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...
Earth work excavation for pipeline trenches in all kinds of soils by mechanical means as per drawing and technical specifications, including setting out, construction of shoring, strutting, barricadin...
Construction of Embankment by excavating the available approved Gravel/Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading,...
Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 ...
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...
Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...
Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...
Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...
Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/...
Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine...
Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine...
Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...
Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...
Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...
Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height....
Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...
Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm,aggregate cement rat...
Providing and filling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight
Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand)
Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS C...
Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/...
Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/w...
Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of appro...
Constructing brick masonry chamber of internal dimension 600x600mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plaster...
Constructing brick masonry chamber of internal dimension 450x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plaster...
Providing and fixing SFRC frame and cover conforming to IS 12592 (part-I)-1988 and IS 12592 (part-II)- 1991 with latest amendment, including cutting slabs to the required size for the opening and fixi...
Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) inc...
Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...
Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster with cement mor...
Providing 15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) including rounding off corners wherever required smooth rendering, providing and removi...
Providing 12 mm cement plaster with cement mortar 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding,...
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Iv...
Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per s...
Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding for Bathrooms: Toilet: Chemically exposed areas and jo...
Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding for Bathrooms: Toilet: Chemically exposed areas and jo...
Providing skirting, dadooing, rises of steps with colour glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed t...
Providing S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work sit...
Providing S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work sit...
Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 m...
Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. compl...
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. ...
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with stan...
Providing and fixing granite stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with c...
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangula...
Providing and fixing PTMT stop cock of approved quality and colour 20 mm nominal bore, 89 mm long, weighing not less than 88 g
Providing and fixing brass bib cock of approved quality: 20 mm nominal bore
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangment and making necessary holes for inlet, outlet and ov...
Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 25mm including the cost of materials, labour charges, required tools and plants etc., complete. W...
Providing and applying primer coat with SS1 grade Bitume Emulsion on prepared surface of granular base includin cleaning of road surface and spraying primer at the rate of 0.70 kg/m2 using mechanical ...
Providing and laying Bituminous Macadam with 100 tph capacity hot mix plant batch type using crushed aggregates of specified grading premixed with bituminous binder VG-30 @ 3.3% by weight of mix, tran...
Providing and laying Bituminous Concrete with 100 TPH capacity hot mix plant batch type using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 5.2 per cent of mix and f...
Providing and applying tack coat with RS1 Bituminous Emulsionusing emulsion pressure distributor at the rate of 0.20 kg/m2 on the prepared bituminous surface cleaned with mechanical broom.
Providing & fixing of 3-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastom...
Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...
Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...
Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...
Providing and installing at site of work P.V.C. pipes including cost of pipes and specials and labour, including lowering into trenches, laying true to line, level and perfect linking at joints leak p...
Providing & fixing of louvered ventilator made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead fr...
30mm thick factory made polyvinyl chloride (PVC) door shutter made of a uPVC hollow section of size 60x30mm and wall thickness 2 mm (plus or minus 0.2 mm), with inbuilt decorative moulding edging on o...
Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be...
Providing and fixing to existing door frames Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsatura...
Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5mm (heavy type)
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitt...
Providing and fixing factory made UPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance (plus or minus 1mm), with wall thickness 2.0 mm ((plus or minus 0.2 mm)...
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direct...
Fencing with G.I. barbed wire Angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe wi...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe wi...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe wi...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe wi...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...
Providing, Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well confirming to IS 8034-2000 specifications, to work site with testing of as per instructions of engineer incha...
Providing and fixing Rainy dual capacity self-cleaning roof top rain water harvesting filter or equivalent filter of FL-500 specification suitable for a catchment area of about 500Sqm.
Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, co...
Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, co...
Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, co...
Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, co...
Providing and laying at site of work MS casing caps as per IS 1239 (part- II) 1982 with all latest amendments if any for any dia. The thickness of plate used for covering one end shall be 3mm (minimum...
Geophysical investigation at site for sinking borewells for supplying drinking water to the habitation either through the Hand Pump MWS or P.W.S.S, by vertical electrical sounding by adopting Venner o...
Providing Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000 ; 3Phase, SS Bowl & Impeller with Low volt Motor as per specifications, to work site as per ...
SUBMERSIBLE CABLE
Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest a...
PRESSURE GAUGE :
Supply and delivery at site of brand new best make pressure gauge bourdon type as per IS 778/1984 with ISI Mark and as per its latest amendments - Size 100 mm
Supply and delivery at site of brand new best make gate valve as per IS 778/1984 with ISI Mark and as per its latest amendments Size 50 mm
NON - RETURN VALVE :
Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments Size 50 mm
ix) Control Panel BOARD-A:
Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, A...
POWER CAPACITOR:
Supply and delivery at site best indigenous brand new power capacitor as per IS 2834/1986 with latest amendments with KPTCL authorities and erection, electrification and commissioning...
Supply and delivery at site delivery of best indigenous brand new MCB (Miniature Circuit Breakers) of required capacity as per IS 88228/1978 and its latest amendments and with ISI Mark of 6/10/16...
Erection elctrification & Commissioning works of pumpsets :
Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including suppl...
Erection of panel board & meter board Unit :
Labour charges for erection of outdoor type panel board and meter board units with all necessary materials and labour, tools and equipmentsincluding provi...
Main connections:
Providing main connection from pole PVC insulated sheathed steel wire cable in new trench as per IS 1554/ 1988 with latest amendments with ISI mark from KPTCL pole to meter board un...
Supplying and fixing sheet Metal box made out of 18SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 100 x 75 x 65 mm
Supplying and fixing sheet Metal box made out of 18SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 135 x 75 x 65 mm
Providing, laying and jointing HDPE pipes of specified grade and conforming to IS 4984-2016 with latest ammendments and conveying to work site including loading and unloading at both destinations and ...
Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and runni...
Supplying heavy gauge PVC Conduit Pipe .... dia ....... mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks an...
Supplying heavy gauge PVC Conduit Pipe .... dia ....... mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks an...
Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...
Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...
Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...
Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...
Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall
Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall
Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall ...
Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 8...
Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...
Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...
Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...
Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...
Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...
Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...
Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...
Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...
Supplying & fixing of Porcelain fuse channel with cutout on existing wooden/panel using necessary nuts, bolts and washers. 100 A
Supplying of on load change over switches 4 poles,AC-23A Duty,415V,50Hz,AC Supply. With all accessories. (SMEnclosure Sheet Metal Execution) 100 A
Supplying of 1440rpm heavy duty exhaust fan with bracket blades suitable to operate on 230V 50Hz, AC Supply complete. - 15" Sweep (450mm)
Supplying exhaust fan of 1440 RPM of 300mm (12") size with bracket blades complete for light duty suitable to operateon 230V 50Hz, AC Supply.
Fixing one exhaust fan after making a suitable notch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets, with bolts and nuts and a 5 A, ceiling rose with...
Supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc., for operation on 230 volts, 50 cycles. Single phase AC supply conforming to ISS-374-1979 and with double ba...
Supplying wall mounting fan suitable to operate at single-phase 230v AC supply. 400 mm Sweep
Fixing a ceiling/wall mounting fan of all capacities and all types to the existing 'S'' hook with fan regulator to the existing board together with supplying and fixing 5 A. ceiling rose, necessary le...
Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...
Supplying and fixing regular MCB distribution boards on wall / wood board / flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase ...
Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capa...
Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capa...
Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. And M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. ...
Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. And M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. ...
Point wiring using Copper wire without switch.
Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth ...
Point wiring using Copper wire without switch.
Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth w...
Point wiring using Copper wire without switch.
Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using copper PVC insulated multi strand 2x1.5Sqmm copper wire without...
Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and runni...
Supplying, fixing and wiring 0 to 1500amps CT operated AC analog type Ammeter With out CT
Supplying, fixing and wiring 3 Phase Digital Ammeter / Voltmeter
Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440VAC. 50 Hz 12/24V D.C.
Supplying, fixing and wiring Electronic Trivector Meter (ETV) 5 to 32/63A three phase 4wire whole current class-1 Accuracy Energy Meter.
Fabricating supplying and mounting MS box made out ....SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped...
Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit. The pit shoul...
Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc using 40mm dia 2.9mm thick 2.5 mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed o...
GI/Copper strips for grounding connections, using necessary fixing materials as required. 600x600x3mm copper plate
GI/Copper strips for grounding connections, using necessary fixing materials as required. 25 x 3 mm Copper strip
Grounding of equipment with 50 x 6 mm G.I. Flat and connecting equipment to the earthmat/ground pit. Each point of earthing with all formation works like bending, twisting, drilling of holes and conne...
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two coats on new work over an under coat of suitable shade with ordinary paint of appro...
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less tha...
Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two coat applied @ 1.67L/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint ...
Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface like Roof, bathroom...
Providing and laying 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nomin...
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 ...
Providing and laying flooring and steps fine machine polished granite stone slabs 20 mm thick on cement mortar bed 1:6, 20 mm thick, and joints finished with cement mortar 1:3 over existing cement con...
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 g/L of approved brand and manufacture, including applying additional c...
Supplying PVC flexible conduit pipe ....mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using N...
Supplying And Fixing Metal Fan Box with Round Hook.
Supplying of recess mounting non integrated type LED down light 18W luminaire comprising of pressure decast/ extruded aluminium housing, with spring loaded false ceiling clamps, LED of Power/COB with ...
Supplying of feet -PVC Batten with integrated LED tube LED light fitting 1 x 4ft - 36/40 W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI greater than 8...
Supplying of feet -PVC Batten with integrated LED tube LED light fitting 1 x 2ft - 9/10 W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI greater than 80. ...
Supplying and Fixing of ---- mm dia class A GI pipe bracket upto 2 ms long bent at suitable angle and fixing to this bracket street light fitting of all capacities to GI or GI or rail or RCC pole / wa...
Supply of round/square recess/surface mounted rolling type LED Down light withLED square or round down light 5-6W GU 10 LED Lamp Rib Fabricated from diecast aluminium with white powder coated prewire...
Extra length of GI pipe of class B 19mm dia for down rod.
Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...
Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capa...
Supplying, fixing andwiring Residual current circuit breaker (RCCB) 240/450V upto 300mA sensitivity on existing wood/ panel board. 16A-25A 2 pole
Supplying, fixing and wiring Residual current circuit breaker (RCCB) 240/450V upto 300mA sensitivity on existing wood/ panel board. 63 A 4 pole
Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50HzAC with latest micro controller based, digital read out of percentage leakage curr...
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A One Way Switch
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A Two Way Switch
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A Three Way socket
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. Stepped Fan Regulator Two Module
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 16A One Way Switch
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A Bell Push
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 32A DP Switch
Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6/16A Universal Socket
Supplying and fixing hylum plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N. F. screws.
Extra for supplying 4 mm thick white plastic plate and covering for junction boxes of size ...... mm conduit using necessary machine screws. 80/90 mm.
Extra for supplying 4 mm thick white plastic plate and covering for junction boxes of size ...... mm conduit using necessary machine screws.110 mm.
Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Pendant Holder.
Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capa...
Fixing all types and all capacities of fluorescent /falseceiling/ spot light/CFL/LED fittings indoor on the wall/ceiling/rafters/girders using 23/0.0076" twintwisted PVC insulated wires, required No...
Station mandatory spares
Circuit Breaker (CB)
Closing coil with resistor (For one Complete Circuit Breaker)
a) for 145KV CB
Tripping coil with resistor (For one Complete Circuit Breaker)
a) for 145KV CB
Terminal Pad (For one Complete Circuit Breaker)
a) for 145KV CB
Terminal Connector (For one Complete Circuit Breaker)
a) for 145KV CB
SF6 Gas (40% of total gas Qty. for Sub-Station)
Isolator : Copper Contract fingers male & female (For one Complete Isolator)
a) for 110KV Class
Terminal Connector (For one Complete Isolator)
a) for 110KV Class
Terminal Pad (For one Complete Isolator)
a) for 110KV Class
Grand Total weight of Tower parts- Mild Steel
Note:(i) Rate to be quoted on per t Basis.
(ii)Refer Techno-Commercial sheet for detailed break-up
Grand Total weight of Bolts & Nuts
Note:(i) Rate to be quoted on per t Basis
(ii)Refer Techno-Commercial sheet for detailed break-up
Tower accessories :
i.Number Plates-10Nos.
ii.Danger Boards-10Nos.
iii.Circuit plate-20Nos.
iv.Phase plate (Set of 6 No.)
v.Earth bond 300 mm long
vi.Earth bond 450 mm long
Grounding of towers including cost of 40 mm dia 2.5 mm thick, class 'C' G.I. pipe of 3 Mtrs length as per specifications, with 50 X 6 mm GI flats 3 Mtr long, salt, charcoal including excavation charge...
Conductor & Earth wire :
i) Lynx ACSR Conductor plain terrian
ii) 7/3.15 mm GI Ground wire
I) Insulator strings for Panther ACSR conductor as per technical specifications (110kV Line)
NOTE: All the Insulator strings and hardware fittings quoted by the bidder shall be of the same type i.e. a...
B. Suspension insulator strings consisting of any one of the following:
a. Insulator string consisting of 1X7nos. of 90kN Disc insulators
b. Porcelain long rod...
II.Insulator Hardwares suitable for Panther/Lynx/Drake ACSR Conductor as per Technical Specification:
i) Single Tension Insulator with Clamp and accessories suitable for 110kV insulators and Panther C...
ii)Double Tension Insulator with Clamp and accessories suitable for 110kV insulators and Panther Conductor
ii)Single Suspension Insulator with Clamp and accessories suitable for 110kV insulators and Panther Conductor
Accessories for Panther ACSR Conductor
i.MSC Joints suitable for Lynx ACSR
ii.Repair sleeves suitable for Lynx ACSR
iii.P G Clamps suitable for Lynx ACSR
iv.Vibration dampers for Lynx ACSR
v.Pre formed armour rods suitable for Lynx ACSR
Hardware for Earthwire
i.MSC Joints suitable for Ground conductor
ii.Repair sleeves suitable for Ground conductor
iii.Single Tension clamps (bolted type) suitable for Ground conductor
iv.P G Clamps suitable for Ground conductor
v.Single suspension clamps (bolted type) suitable for Ground conductor
Check survey using their own equipment for 110 kV Plain terrain.
Check survey to be conducted during construction stage: Conducting detailed check survey along the approved route duly following...
Conducting drone survey of Transmission lines for collection of data along with Aerial inspection of EHV line corridor using LIDAR method for measurements of vertical,horizontal and ground clearnace o...
Conductor & Earth wire:
Coyote Plain Terrian (1.275Km)
Ground wire 7/3.15mm steel Plain terrian (1.275Km)
Erection of Transmission Line Towers (including tower accessories etc., except GI angle, Barbed wire & Grounding materials) as per specifications.
(i)The Bidders are required to quote the rates...
Tower Accessories:
Supplying and fixing Gl angle 45 x 45 x 5 mm (1Mtr length) with cleats, bolts nuts as per specification and fixing above 0.5mts length each at inner and outer surface of tower to fa...
Supplying and fixing Barbed wire
Grounding of towers including cost of 40 mm dia 2.5 mm thick, class 'C' G.I. pipe of 3 Mtrs length as per specifications, with 50 X 6 mm GI flats 3 Mtr long, salt, charcoal including excavation charge...
Dismantling of existing super structure / tower material
Dismantling of of existing 110kV DA+0 Towers
Releasing & restringing of Lynx Conductor (0.534x6)
Releasing & restringing of Ground wire (0.534x1)
Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...
Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...
Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...
Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...
Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...
Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...
Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite /trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant I...
Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...
Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/w...
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
Annexures and Circulars-Chitta.zip
Tender Document • 3.50 MB
sec 7 tech spec.zip
Tender Document • 19.51 MB
Sec 11a Techno Com 110kV_WI-2572.xlsx
Techno-Commercial Worksheet • 1.08 MB
Drawings Chitta.zip
Tender Document • 0.73 MB
Prebid Proceedings-WI-2572 and 2573.pdf
Others - Prebid Proceedings-WI-2572 • 1.03 MB
NIT Chitta-WI-2572.pdf
Tender Document • 15.46 MB
Tender Doc Chitta WI-2572.docx
Tender Document • 0.52 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .