REPAIR TO PATH, DRAIN, GATES, BOUNDARY WALL, PCC HARD STANDING AND OTHER MISC WORK IN OMQ AREA AT VSN NAGPUR

Amount

Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including floor finishes.

Demolition of cement concrete (reinforced) any description and in any position not otherwise specifically provided for all as specified and as directed.

Demolition of reinforced cement concrete (reinforced) of any description and in any position (reinforcement cut to facilitate demolition not otherwise specially provided for) all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry in CM.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed.

Dismantling of structural steel work of any description including doors, gates but excluding framed trusses etc) all as specified and as directed.

M & L Pre cast reinforced cement concrete 1:2:4 type B1 (Using 20mm graded stone aggregate) set in cement mortar 1:4 for man holes cover slab all as specified and directed by engineer charge.

M&L mild steel deformed bars 10 mm dia cut to length bent to shape required including cranking , bending and binding with MS wire (annealed) not less than 0.9 mm dia all as specified and as directed by engineer-in-charge.

All as per item No 8 above but 5 to 10 mm dia in stirrups.

M&L hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M & L for 100mm thick plain Cement concrete 1:2:4,type B-1, using (20mm graded stone aggregate), complete all as specified and as directed.

M&L for PCC in 1:2:4 type B-1 using 20 mm graded stone aggregate as in coping including weathering round or chamfered and necessary form work required all as specified and directed by engineer in charge.

M&L for 100 mm thick PCC in 1:4:8 type D2 using (40 mm graded stone aggregate) as in floors, path & hard standing etc all as specified and as directed.

M & L for cement concrete coloured interlocking rouber moulded paver block not less than 60 mm thick of approved shape and colour and size laid over and including stone dust 25 mm thick, complete all as specified and as directed.

M&L brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6.

Taking down cement plaster on brick or concrete surfaces on wall/ceilling etc including racking out joint, hacking for key,scrubbing down with water etc all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 over brick or concrete surfaces, finished even and smooth using water proofing compound @ 3% by weight of cement. Note: WPC shall be measured and paid separately.

M&L for rendering 15 mm thick in CM 1:6 over brick surfaces, finished even and smooth without using extra cement all as specified and as directed.

M&L prepration of new plaster surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed by EIC

M&L complete removal of existing treatment and application of two coat of exterior emulsion paint of electric blue or AF blue colour or white colour as approved by GE, using ultra clean paint or Dulax ICI or Apex Ultima of Asian Paints or equivalent in Berger Paints over a coat of primer on the new wall surfaces, edges of slab, roof/chajja projection and column etc., after necessary preparation all as specified and as directed.

M&L for rendering 10 mm thick in CM 1:3 on ceillng, finished even and smooth all as specified and as directed.

M & L applying two coats of OBD over a coat of primer on newly plastered wall surfaces including preparation of surfaces all as specified and as directed.

Supply only integral water proofing compound.

Grubbing up tree trunk including cutting of trunk protrude over brick wall,chajja,roof digging out roots filling hole with concrete 1:2:3 type B 0 (using 12.5mm graded stone aggregate) girth of tree n exc 30cm and n exc100cm and removing of unserviceable material to a distance n exc50m and clearing sitecomplete all as specified .

M/L for welding in repairs n exc 2.5cm in length n exc 6mm thick all as specified NOTE-welding venilators, windows,door etc.

M&L RCC 1:2:4 type B1 using 20mm graded stone aggregate as in foundation footing etc all as specified and as directed.

M&L RCC 1:2:4 type B1 using 20mm graded stone aggregate as in column, pillars, post etc all as specified and as directed. Note for item No 26 & 27 Form work and re-inforcement shall be measured and paid separately.

Form work to sides of concrete foundations, footings, bags of columns, raft and raft beams, sides and soffit (if any) of foundation and plinth beam and similar work vertical or to better for rough finished surface of concrete all as specified and as directed.

Formwork to sides of pillars, post, struts, column square or rectangles or polygon for rough finished surface of concrete all as specified and as directed.

M&L rendering 10 mm thick on fair faces of brick /concrete surfaces in cement mortor 1:3 finished fair and even all as specified and as directed.

S&F mild steel Framed works such as in fencing posts/ struts in fencing including cutting top to shape as directed, drilling holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work confirming Fe 410-0 or Fe-310-0 all as specified and as directed.

S&F mild steel framed work such as in doors or gates using angle or other sections with gusset plates, rails, braces etc complete, drilled for and including steel sheeting or covering as required. Doors etc to be prepared for hanging or sliding with and including hooks and hinges of steel for hanging door and other fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

Fixing only Chain link fencing including line wires any mesh size and type to any type of standards, rails straining bolts etc including provision of binding wire all as specified and as directed.

Supply only Chain link MS galvanised fencing, any size or type all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10cm width or grith and apply two coats of synthetic enamel over a coat of red oxide primer all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or grith and apply two coats of aluminium paint all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or grith and apply two coats of Synthetic enamel paint all as specified and as directed.

M&L for preparation of new or untreated surfaces of walls plastered and apply three coats of white wash all as specified and as directed.

Maintenance of rolling shutters of any size upto 5.5 m wide with easioning, greasing, necessary welding to make the shutters full functional and easy operational including minor spares and materials costing upto Rs. 200/- as required all as specified and as directed. Note Safety lever lock/ ball bearing and other major spares if required will be replaced and paid separately.

S&F Safety lever locks mild steel with 4 levers for rolling shutter all as specified and as directed.

S&F ball bearing for rolling shutters all as specified and as directed.

S&F MS vertical guide of rolling shutters of standard size and thickness matching to the existing including taking down old one all as specified and as directed.

S&F MS locking plate of rolling shutters including taking down old one all as specified and as directed.

S&F MS profile sheet of rolling shutters matching to the existing including taking out old one all as specified and as directed.

M&L providing PCC 1:2:4, type B1 (using 20 mm graded aggregate), 40 mm thick, finishing cement concrete surfaces even and smooth using extra cement all as specified and as directed.

M & L providing PCC 1:2:4, type B2 (using 40 mm graded aggregate), 75 mm thick, finishing cement concrete surfaces even and fair without using extra cement, as in plinth protection, path etc including necessary form work and provision of bituminous joints mixed with bitumen and sand at intervals not exc 3.00mtr all as specified and as directed.

M & L Brushing neat cement slurry with 3 Kg of cement per sq metre all as specified and as directred.

M&L for making good the disturbed brick/ concrete surfaces with CM 1 : 4 10 to 15 mm thick and finishing the surfaces fair and smooth to match with the existing surfaces all as specified and as directed.

M&L PCC in 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling, mass concete etc all as specified and as directed.

M&L 450 mm bore reinforced concrete pipes, class NP2, laid and jointed complete with collars all as specified and directed.

M&L 600 mm bore reinforced concrete pipes, class NP2, laid and jointed complete with collars all as specified and directed.

M/s Ashwin Bhange

Vishwakarma Engineering Works

Sharma Electrical and Services

Arnav Enterprises

M/s Prakash R. Verma

dhanshree enterprises

Harsh Construction Company