SPL repair to Bldg No P-137 and SPL repair/replacement of BER summer appliance and Provn of 40 X Desert cooler at Bharatpur Mil Stn

Amount

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc, complete all as specified.

M&L for PCC type D2 (1:4:8) using 40 mm graded crushed stone aggregate as in foundation,filling/bed/mass concrete complete all as specified.

M&L for Brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius, built in cement and sand mortar (1:4), complete all as specified.

Taking down cement or cement lime plaster of any description from brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified.

M&L for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified.

M&L for rendering 15 mm thick in cement and sand mortar 1:4 on other than fair faces of brickwork or cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of concrete surfaces as in ceiling including finishing the surface even and smooth without using extra cement, complete all as specified.

Demolition of cement concrete(reinforced) roofs, floors, beams,staircases, landings, chajja and similar suspended work, complete all as specified .

M&L for Form work to sides and soffits of floor or roof beams , beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc for rough finished flat surfaces of concrete, complete all as specified .

M&L for MS TMT bars ,10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.

M&L for RCC Nominal Mix ,type B1 1:2:4 using 20 mm graded stone aggregate for Beams, cantilevers, bressummers, lintel beam etc. complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings nexc 15 cm thickness (below or above ground levels) complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified .

M&L for 25 mm thick PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregate as in sub floor, laid and finishing the surface of concrete topping even and rough to receive screed for tiling, complete all as specified.

M&L for 40mm Thick PCC type B-1,(1:2:4) using 20 mm graded stone aggregate with liquid water proofing compound as per manufacturers specification finished even and smooth without using extra cement complete all as specified.

M&L for vitrified ceramic tiles, 8 to 10 mm thick (square/rectangular) polished, area of each tiles not exc. 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified.

M&L for glazed ceramic tiles, coloured/printed tiles in vertical surface of size 450x300x7 mm thick, laid over 10 mm thick rendering in cement mortar (1:3) and set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles, complete all as specified and as directed.

M&L for 18 - 20 mm thick black machine cut granite slab (of any type) (table rubbed and polished), as in steps, jambs, pillars, window- cills, cooking platform set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab laid over and including 15 mm thick cement screed in cement and sand mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situation including making of hole suitable for gas pipe etc. complete all as specified and as directed.

M&L for preparation of new plastered or un plastered surfaces of wall including cornices, pilasters etc and applying two coat of cement based paint of approved colour on wall Surface including all necessary arrangement for execution of work, complete all as specified.

M & L Preparation of new plastered or un plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of Distemper Oil emulsion white or tinted over a coat of alkali resistant primer complete all as specified.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceiling including cornices, pilasters etc by brooming down and applying one coat of white wash, complete all as specified .

M&L for preparation of old plastered surfaces of wall including cornices, pilasters etc by brooming down and applying one coat of oil bound distemper, complete all as specified.

M&L for preparation of old plastered or un plastered surfaces of wall including cornices, pilasters etc and applying two coat of cement based paint of approved colour on wall Surface including all necessary arrangement for execution of work, complete all as specified.

Dismantling wall lining and ceiling boards ( fibre, pulp, insulation ,etc. ) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified .

S&F anodised aluminium snap grid frame work of grid size 605 x 605 mm false ceiling complete all as specified .

S&F for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

S&F for 4 mm thick non-asbestos fibre cement building boards fixed aluminium framework, complete all as specified . Note: Frame work for ceiling shall be measured and paid separately)

S&F for PVC wall panelling with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angle fixed with solvent cement complete all as specified as manufacturer's instructions complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified.

Dismantling asbestos cement/galvalume/fibre glass (corrugated or semi corrugated) sheets in roof coverings, complete all as specified.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections, MS Pipes) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A', complete all as specified.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

Pre painted galvalume alumimnium zinc coating GI based corrugated steel sheet 0.50 mm thick, sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified.

Roughening surfaces of old concrete floor/Chajja/facia /any type concrete projections by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified.

M & L for brushing neat cement slurry with 3.0 kg of cement per sq. m complete all as specified..

M & L for granolithic concrete 1:1:2 concrete surface topping 30 mm thick; laid over cement concrete etc. and finished to an even and fair surface complete all as specified.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection/path laid in panel surface finished even and fair without using extra cement complete all as specified.

M&L for sand stone slabs of 75 mm thick in cills, landings, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete all as specified .

S&F in repair powder coated aluminium frame for doors, windows, ventilators with one or more rebates including aluminium channels for sliding shutters, jointing cleats for fixing etc., complete all as specified.

S&F in repair powder coated aluminium window/ ventilator shutters side hungs type with sash, aluminium section weight not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stay 150 mm long (1 No) suitable , type B-21 hinge 100 mm long (2 No), suitable handle (1 No) etc for each leaf, complete all as specified.

S&F in repair powder coated aluminium door shutters with aluminium section weight not less than 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, 02 Nos aluminium handle each door, 03 Nos hinges, anodised aluminium snap beading screws etc., complete all as specified.

S&F in repair aluminium deco grill in door and windows with weight not exceeding 1.00 Kg/Sqm including necessary arrangement for fixing etc Complete all as specified.

S&F for 4.00 mm thick sheet glass with solar control film 25 micron reflective type sticked to glass pane ,ordinary quality exc 0.5 Sqm in each pane complete all as specified .

S&F for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified.

S&F Door closer hydraulically regulated designation No 3, univeral type, of aluminium (extruded section body), suitable for door shutters, complete all as specified.

S&F Aluminium Door seal of overal size 42 mm having nylon brush of 20 mm fixed on aluminium body strip of 22 mm, fixed with screw on Aluminium door, wooden shutters or PVC shutters complete all as specified.

S&F 100 mm mild steel 4 lever mortice lock vertical type complete all as specified.

M&L for 18 mm thick PVC boarding shutters of density exc 550 Kg per Cum but nexc 600 Kg per Cum one side decorative lamination & other sidebalancing lamination sheet fixed with brackets, screws etc, Panels shall be fabricated using adhesive and screws wherever required all the edges shall be coverd with 18 mm x 1 mm thick edge bending tape or 90 degree edge bend finish as per manufactrure specification or approved pattern including taking down existing shutter complete all as specified.

M&L for 18 mm thick PVC boarding shelves of density exc 550 Kg per Cum but nexc 600 Kg per Cum one side decorative lamination & other sidebalancing lamination sheet fixed with brackets, screws etc, Panels shall be fabricated using adhesive and screws wherever required, Supported for three sides with 18 mm x 18 mm PVC Ply fixed with Screw all the edges shall be coverd with 18 mm x 1 mm thick edge bending tape or 90 degree edge bend finish as per manufactrure specification or approved pattern including taking down existing shutters complete all as specified.

S&F for stainless steel 125 mm handle not less than 12 mm dia suitable for cupboard shutters with self tapping stanless steel screw complete all as specified.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 40 mm complete all as specified.

S&F Magnet catch for shutters as per approved sample complete all as specified.

Taking down chowkats or frames n. exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame) complete all as specified.

S & F for Solid PVC Door Frame of the size 50 x 47mm made out of 5 mm PVC sheet. The door profiles are to be reinforced with 19x19mm M.S Square tube. The profile shall be cut and mitred at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube inside the 19mm x 19mm M.S. square tube and suitably screwed complete all as specified.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified & shown on SSR 2020 (Part-II) complete all as specified.

S&F SS hinges medium weight of size 100 mm, complete all as specified.

S&F Aluminium handles, cast type, anodised of 150 mm size complete all as specified.

S&F aluminium anodised,barrel tower bolts of extruded section, 200 mm length of bolt and fixed with screws, complete all as specified.

Cutting or uprooting grass incl removing old mud phuska/ roof treatment of 100 mm thickness and description, removing rubbish off the premises, cleaning surface and preparing to receive new treatment complete all as specified.

M&L for 20 mm thick screed bed or bedding layer of cement mortar 1:4, finished even and smooth without using extra cement complete all as specified.

M&L for preparing surfaces for roof treatment by removing all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surfaces mechanically or by grinding to make it smooth before application, repair all cracks by cutting "V" groove and fill with PMC mortar (Polymer modified cement mortar) prepared by cleaning free from dust and loose particles and apply on dry surface first coat of crack fillar using putty knife or trowel allow to dry for 4 to 6 hr, afterthat apply second coat and dry for 4-6 hrs in ratio as per manufacturers specification, provide 75 mm x 75 mm coping made out of PMC mortar as above on all joints of vertical upstands to ensure that moisture content in the prepared surface does not exceed 5% immediately before application of liquid membrane. Material incorporation & Protection be provided as Terrasheild first apply with water (ratio terrasheild : water will be 4:1) as primer with coverage area 0.1 Kg per Sqm. After 2-3 hour later, second step apply directly first coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller.Spread non woven geo textile of 40 / 50 gsm with overlap of 50 mm in both direction when the surface is still tacky. After 4-6 hour later, apply third step apply directly second coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller. final thickness of complete treatment should be minimum 1.0 mm. Water tank and Khurra location one additional coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm be provided. after complete application full curing minimum 7 days . Above complete application will be done by authorized apllicator from Manufacturer and manufacturer's specification. Make : IWL Co/ STP/Fosroc

Taking up or down steel tubing and connections,25 mm bore fixed on walls, floors or ceiling etc complete all as specified .

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etccomplete all as specified .

S&F GI tubing medium grade ISI marked galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 25 mm complete all as specified.

S&F GI tubing medium grade ISI marked galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.

S&F in repair Bib tap, cast copper alloy long body with crutch or butterfly handle, screwed down, suitable for 15 mm nominal bore iron pipe screwed for iron or brass ferrule and fixed complete all as specified.

S&F in repair pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shank and fly nuts, with or without lettered "Hot" or "Cold" for 15 mm nominal bore , screwed for iron pipe and fixed complete all as specified .

S&F in repair 15 mm bore stop valves, cast copper alloy, fancy type chromium plated, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified .

S&F in repair vitreous china wash down water closet (Pedestal pattern) white excluding (flushing cistern and flush pipe), complete all as specified.

S&F in repair vitreous china squatting pan,Órissa pattern size 580 x 440 mm white, with integral foot rest complete , all as specified.

S&F in repair toilet paper holder with flat recessed type stainless steel, fixed to walls with chromium plated (CP) brass screws complete all as specified.

S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device seat and cover for pedestal pan, complete all as specified.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, 10 lit capacity with inlet, ball valve, float and handle including brackets complete all as specified.

S&F in repair of Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe including waste pipe complete all as specified.

S&F in repair Vitreous China wash hand basin, white, flat back, size 550x400mm including brackets & waste pipe of PVC 32 mm bore of low or high densitycomplete all as specified.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S & F in repair, 500 ltr ISI marked three layer, white colour, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with thread type cover and fixed with screw hoisted and fixed in position & including 20 mm brass ball valve complete all as specified .

S&F in repair PTMT ball valve of 20 mm bore high pressure of PTMT with epoxy coated aluminium rod & high denisty plastic ball screwed for iron pipe (minimum wt 142 grams for ball only) complete all as specified and as directed.

S&F welded steel wire fabric ,weight n. exc 4.00 kg/sq. m fixed to steel members complete all as specified.

Demolition cement Concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate with smooth finish etc. complete all as specified.

Taking down carefully copper/aluminium point wiring (light, fan, bell,same board, independent or power) complete fittings such as switches, ceiling roses, pendents, regulators, sockets etc removing materials for taking credit and making good disturbed surfaces of wall, floor & ceiling etc. complete all as specified.

Dismantling of old U/S sub main wiring and service wire of any size & make.

Dismantlingof old U/S rusted main switch/DB of any size capacity and make.

M&L point wiring complete with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in PVC conduit pipe with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface of wall/ceiling by means of PVC sleevel/dash fastners with cadmium plated screws including suitable size of PVC boards/ existing sunken box for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm insulated but unsheathed copper earth continuity conductor to common earth and connedcted to earth dolly complete all as specified for the following :-

One light point controlled by one way switch.

One fan point controlled by one way switch.

One 3 pin 6 Amp socket point outlet on the same board with other switches

One 3 pin 6 Amp socket point outlet on the independent board

All as per item No 91 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps socket point outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified.

S&F ceiling rose surface bakelite 50 x 40 mm three terminal ISI marked including suitable size of PVC board complete all as specified.

S&F socket outlet 2 in 1, 5 pin 5 Amps multi purpose flush type 230 volt complete all as specified.

S&F switch socket combinatin 2 in 1, 5 pin 5 and 15 Amp flush type multi purpose 230 volt complete all as specified.

S&F switch piano flush button single pole one way 6 Amps 230 volt grade.

S&F step type electronic fan regulator EME type 100 watt complete all as specified.

Supply & fix 4 way VTPN Distribution Board,double door for MCBs with IP-40 protection (with provision for MCCB as incomer & WiNtrip MCB as outgoing) complete all as specified.

Distribution board factory made and tested made of sheet metal enclosure powder coated suitable for mounting the MCB 415/240 volt of the following DBs :-.

4 way TPN with 200 amps rated busbar 415 volts (double door type).

8 way SPN with 200 amps rated busbar 240 volts (double door type).

4 way SPN with 200 amps rated busbar 240 volts (double door type).

S&F MCCB, MCB with GI hardware fixed in DB's of the undermentioned type and rating.

MCB SP 240 volts 6-32 Amps C Curve

MCB SPN 40 Amps, 240 volt C Curve

MCB TPN 63 Amps, 415 volt

MCCB,4 Pole, 125 Amps, 415 volt 16 KA

M&L bracket light fitting wall mounting, champagne gold finish fixture with plastic body suitable for 9 W with LED bulb B22 base. Make: Havells/Cromption/ Bajaj etc

S&F Retrofit LED T8 tubular lamp of 20 watt with extruded aluminium body,PC diffuser and inbuilt driver including compact batten suitable for LED T8 lamps , complete with all accessories internally pre-wired and including connecting to ceiling rose with three core flexible copper conductor cable of size 1Sqmm Make Crompton/Bajaj/Havells/Philips/Crompton.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type connecting up with three core flexible copper conductor cable of suitable size complete

S&F in repair modular sheet metal enclosure of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of SP 20 Amps, 240 volts.

Cutting chases,pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing steps cills, sunshades, shelves lintel etc.and cutting chases for concealed water tubing or concealed conduit wiring etc,and making good cutting not exc 10 cm girth on stone concrete block or slab walls complete all as specified.

M&L submain wiring complete with 10 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor three runs and one run of 10 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc complete all as specified.

M&L submain wiring complete with 6 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 4 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc complete all as specified.

M&L submain wiring complete with 4 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 4 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc complete all as specified.

Supply & fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified.

Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 3 Mtr below the ground level with the top edge of earth plate, depth not less than 2.25 Mtr below the ground level connected to connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts and washers protected by GI tubing light grade 40 mm dia uptoTest point 20 mm dia watering pipe with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in any type of soil ,removal of surplus sil and providing charcol dust & salt layers all around the earth plate upto 15 cm all as required specified & directed by engr in charge ( Note:- Up to 7.5 Mtr length of pipe of 40 mm dia and GI strip shall be deemed to be included in unit rate quoted by tenderer GI pipe and GI strip beyond 7.5) will be measured separately under respective item.

S&F G.I tubing light grade including fittings 40mm dia complete all as specified.

S&F 35 watts LED street light fitings new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP66 with 10KV surge protection road way, luminaire with high power LED as light source complete all as specified and directed , Make :- Crompton / wipro / Bajaj / Philips.

S & F street light GI bracket of 0.9 mtr long made out of 32mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of flat iron 25 x 4mm including nuts bolts & washers complete necessary fixing arrangements on pole all as specified.

Material and labour for cutting suitable holes in existing masonary wall and fixing suitable size hume pipe for fixing of exhaust fan 250/300 mm dia and making good disturbed surfaces with cement mortar (1:4) and finished to match existing surface complete all as specified.

S&F exhaust fan of 300 mm sweep 900 rpm with suitable size of MS louvers duly painted , connecting wire PVC insulated twisted flexible 0.5 sqmm copper conductor including all standard accessories complete all as specified .

S&F ceiling fan (white) of 1200 mm sweep, 5 star rating copper wound with super energy efficient BLDC motor including remot,connecting wire PVC insulated twisted flexible 0.5 sqmm copper conductor canopy set, down rod, shackle kit, including all standard accessories & old unserviceable ceiling fan deposited to AGE E/M yard complete all as specified.

S&F LED Recessed full lit luminaire with glare free uniform illumination 2 ft x 2 ft, 24 Watt , complete with all accessories internally pre-wired and including connecting to ceiling rose with three core flexible copper conductor cable of size 1.5Sqmm .

S&F LED surface mounted LED panel injection molded in thermally conductive engineered plastic - FR V0 grade housing, diffuser with high optically efficient material. , complete with all accessories internally pre-wired and including connecting to ceiling rose with three core flexible copper conductor cable of size 1.5Sqmm .

Shifting of Spilt AC System With indoor unit & Outdoor unit with Proper fixing, servicing & Gas Filling with connected Accessories Complete as Specified & directed .

Excavation in trenches, n. exc 1.5 Mtr wide and n. exc 1.5 Mtr in depth for foundation/laying of cable and getting out in soft/loose soil complete all as specified.

Removing of excavated soil to a distance n. Exc 50 Mtr and depositing where directed at a level n. Exc 1.5 Mtr above the starting point complete all as specified.

Returning, filling in including spreading, levelling, watering and well ramming in layers n. Exc 25 cm thick complete all as specified.

Supply & spread unwashed dry river sand for sand cushioning and covering the under ground cable in trenches complete all as specified. (Note :- Punning thickness shall be measured.)

M&L for brick protection with sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as specified.

Supply, laying, testing & commissioning LT XLPE insulated armoured (heavy duty) electric cable with stranded aluminium conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole of the following sizes:-

10 Sqmm 2 core

16 Sqmm 3 core

35 Sqmm 3.5 core

70 Sqmm 3.5 core

M&L for road cutting in 300mm width & 450 mm depth & repair to existing with bitumen premixed incl 150 mm BM complete all as specified.

M&L Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised iron strip 32x6 mm as earthing lead by means of bolts, nuts check nuts and washers of galvanised iron or steel all as showin in electrical plate No 3 connected to earthing test point all as specified or indicated includig testing on completion.

Supply and fix of refrigerator, electric driven (single phase) single door, capacity minimum195 Litres .BEE 5 star rated stabilizer free operation, Make: Samsung/LG/Whirlpool old unsv unit to be deposited to MES store yard all as specified..

Supply and fix of refrigerator, electric driven (single phase) double door, capacity minimum 260 Litres .BEE 3 star rated stabilizer free operation, voltage range 100-300V, Samsung Model No:RT30A3A234R/HL or LG/Whirlpool old unsv unit to be deposited to MES store yard all as specified..

Supply and fix of refrigerator, electric driven (single phase) double door, capacity minimum 310 Litres .BEE 3 star rated stabilizer free operation, voltage range 100-300V, old unsv unit to be deposited to MES store yard all as specified Make -Samsung/LG/Whirepool

Supply and fix of Deep Freezer , electric driven (single phase) double door, capacity minimum 400 Litres .BEE 3 star rated stabilizer free operation, voltage range 100-300V, old unsv unit to be deposited to MES store yard complete all as specified.

Supply and install of inverter type window AC unit complete insulated copper tubing, ecofriendly refrigerent, copper bound rotary compressor complete with cordless remote control unit and dust filter for better indoor air quality with minimum 5 star BEE rating and of capacity 1.5 TR. old unsv unit to be deposited to MES store yard complete all as specified.

Supply and install of inverter type split AC units indoor /outdoor complete insulated copper tubing, ecofriendly refrigerent, copper bound rotary compressor complete with cordless remote control unit and dust filter for better indoor air quality with minimum 3 star BEE rating and of capacity 2.0 TR and old unsv unit to be deposited to MES store yard complete all as specified.

Supply and fix of water cooler electric driven (single phase), having approx storage capacity of 80 litre and nominal cooling capacity of 40 Litres per hour ,refrigerant-R134a made out of stainless steel Make: Blue star model :SDLX4080B or Voltas/USHA and old unsv unit to be deposited to MES store yard all as specified .

Supply, fixing and fabrication and testing in replacement of desert cooler in GI body sheet with and including cooler fan motor size/sweep 450mm (fan blade only) 230 Volts, Single phase 50 Hz, 1400 RPM, heavy duty single sheet, totally enclosed. The overall dimesnions of the desert cooler shall not be less than 690mmx 690mm x 1020mm with and including following accessories each and old unsv unit to be deposited to MES store yard all as specified (a) Air grill of suitable size made out of 0.5mm PGI sheet including GSS arrangement with a knob for easy and smooth movement complete all as specified. (b) Front & Side panel made out of 1mm thick PGI sheet of suitable size and shape complete all as specified. (c) Water tank height shold not less than 11 inch made out of 1mm thk PGI sheet complete all as specified. (d) Submersible pump electric driven single phase 230 volts, 50 Hz of suitable discharge and head but motor capacity not less than 18 watt. Make : Khaitan/Crompton or equivalent make. (e) Service cord of 3 Core copper wire 1.5 Sqmm with plug top 5 Amp length not less than 2 metres. (f) Electronic fan dimmer 1000 watts AC 230 Volt for controlling the fan speed. (g) Complete electric wiring of desert coolers as required to operate fan and pump along with 5 Amp switches . (h) Make of cooler fan motor: Khaitan/ Havells/Crompton Greaves/Marathon/Almonard (j) Make of PGI sheet. Tata/Jindal/National

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 100 V to 300 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 2.0 KVA .

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 300 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4.0 KVA .

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 90 V to 280 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA

Supply, fixing and fabrication and testing desert cooler in GI body sheet with and including exhaust fan size/sweep 450 mm (fan blade only) 230 Volts, Single phase 50 Hz, 1400 RPM, heavy duty single sheet, totally enclosed. The overall dimesnions of the desert cooler shall not be less than 820mmx690mm x 1120mm with and including following accessories each. (a) Air grill of suitable size made out of 0.5 mm PGI sheet including GSS arrangement with a knob for easy and smooth movement. (b) Front panel made out of 0.60mm thick PGI sheet of suitable size and shape. (c) Water tank of capacity not less than 120 Litres. (d) Submersible pump electric driven single phase 230 volts, 50 Hz of suitable discharge and head but motor capacity not less than 40 watt. Make : Khaitan/Crompton or equivalent make. (e) Service cord of 3 Core copper wire 1.5 Sqmm with plug top 5 Amp length not less than 2 metres. (f) Electronic fan dimmer 1000 watts AC 230 Volt, 2 module for controlling the fan speed. (g) Complete electric wiring of desert coolers as required to operate fan and pump along with 5 Amp switches . (h) Exhaust fan shall be mounted on wooden frame duly fixed with cooler body. (j) Make of exhaust fan. Havells/Crompton Greaves/Marathon/Almonard (k) Make of PGI sheet. Tata/Jindal/National

M&L for making desert cooler stand made out of 40X40X5mm ISA angle iron work of required size complete paint with two coats of synthetic enamelled paint over a coat of zinc chrome primer complete all as specified and directed by Engr-in-Charge.

PD GUPTA AND COMPANY (BID ID -3162234)

GOVIND CONSTRUCTION (BID ID -3162619)