Loading
Loading…
Loading…
Tender Value
₹44.8 L
EMD Value
₹89,550
Closing Date
22 Jun 2026, 6:00 pm
GE (E) JABALPUR
GE (E) JABALPUR-482011
SPECIAL REPAIR TO BLDG NO P-498 (OFFRS MESS AREA) AT 506 ABW JABALPUR UNDER GE (EAST) JABALPUR
2026_MES_768956_1
8882/E8
Open Tender
Civil Works
240 days
GE (EAST) JABALPUR
Please refer Tender documents.
7 documents required · 7 mandatory
₹500
GE (EAST) JABALPUR
₹89,550
Yes
1 Jun 2026
1 Jun 2026
27 Jun 2026
1 Jun 2026
22 Jun 2026
15 Jun 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. | |||||
| 2M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces of wall in CM 1:6 and finished even and smooth (without using extra cement) complete all as specified and directed. | |||||
| 3M&L for 5mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 as in ceiling complete all as specified and directed. | |||||
| 4M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces of wall in CM 1:4 using water proofing compound (WPC) and finished even and smooth (without using extra cement) complete all as specified and directed. Note: WPC measured and paid separately | |||||
| 5Supply only integral waterproofing compound | |||||
| 6Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified and directed. | |||||
| 7M&L for Brick work with old size FLY ASH bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. | |||||
| 8M& for Brickwork with old size flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in built in cement mortar 1:4 complete all as specified and directed. | |||||
| 9Repairing sunken floor leakage as per following steps:- Surface preparation:- (i) Prior to application of Dr fixit powercrete, ensure to clean the substract which shoud be free from all the dust, foreign particles, loose aggregate and oil grease etc. This can be done with the help of scarifying, grinding, water jetting and sand blasting etc. (ii) The surface should be wetted well prior to application throughly with water to get SSD condition. (iii) All the depression or pin holes/pot holes to be repaired using Dr Fixit powercrete method mortar in mixing ratio of (1 kg cement : 1.50 kg silica sand : 0.50kg of Dr Fixit powercrete). Coating application:- (i) Mix Cement with Dr. Fixit Powercrete in ratio of 1 : 0.50 ( 1 kg cement OP C53 : 0.50 Dr. Fixit Powercrete ) by weight. (ii) The mix should be stirred thoroughly until smooth homogeneous paste is obtained. (iii) Apply first coat over SSD/wet condition substrate. (iv) Apply and unroll woven glass fibre cloth evenly on the wet coating before it dries out on larger areas. (v) Using a nylon brush, apply a coat of Dr. Fixit Powercrete coating over the glass fabric so as to cover the fabric, allow 5-6 hours of air drying before application of another coat of Dr. Fixit Powercrete slurry coating over the surface. (vi) Provide polymer modified protective plaster of 15-20 mm thick over the coating to ensure safety from mechanical damage. | |||||
| 9.01 | Curing:-
(i) Allow Dr. Fixit Powercrete coating to air cure for 3-6 hours after the final coat.
(ii) Do not allow the rapid drying of the coating by covering the coating with help of polythene sheet in case of high humidity and windy condition.
(iii) However, a moist curing after the air drying is advisable.
(iv) Following the moist curing, Dr. Fixit Powercrete coating shall be allowed to air cured for 3 days before submerging it in water.
Note - The above procedure is given for Dr Fixit Powercrete, any other equivalent make may please be used as per their manufacturer's instruction subject to approved by Engr-in-Charge. | - | - | - | - |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.37 MB
BOQ_861137.xls
BOQ • 0.47 MB
TENDER8882.pdf
Tender Documents • 1.45 MB
Download all tender documents and submit your bid