REPAIR AND MAINT TO FENCING, BOUNDARY WALL, GATES, PATH, DRAINS, CULVERTS, HARDSTANDING, PAVED AREAS AND ALLIED WORKS IN ZONE B OF AGE B/R-I (CENTRAL) UNDER GE(CENTRAL) KHADKI

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M & L for PCC 1:4:8 type D2 using 40mm graded aggregate as in foundation filling and mass concrete complete all as specified and directed.

M & L for PCC 1:2:4 type B2 using 40mm graded aggregate as in fixing fencing post complete all as specified and directed.

M & L for PCC (1:3:6) Type C1 using 20 mm graded stone aggregate as in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed incl necessary form work and finished even and smooth without using extra cement complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation,post hole etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out, in any type of soil complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers n. exc 25cm in soft/loose soil in excavated pit or trenches complete all as specified and as directed.

Removing excavated soil/material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S & F for mild steel framed work (Conforming to FE-290, Gde E-165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S & F Mild steel work as in fencing posts and struts, swan neck in fencing incl cutting tops to shape as directed drilling holes nothing for wire etc flat iron fillets (for securing wire mesh) incl all necessary steel bars conforming to FE-410-O or FE-310-O incl one shop coat of primer zinc chromium complete

S&F for Mild steel screw bolts dia of neck 5 to 10mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,exc 5cm & n.exc 10 cm long

S&F 1.25mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

Supply only Chain link MS galvanised fencing, any size or type, complete all as directed and approved by GE.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

Dismantling fencing wire mesh, any type and size, complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles.

M & L for pre-cast cement concrete solid block masonry with solid block of the grade C-1, (1:3:6) using 20mm graded aggregate set in CM (1:6) complete all as directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 all as specified and as directed.

All as per item No 18 above but except stone complete all as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling, coursed, hammer dressing with maximum depression on face from straight edge held against the dressed surface n.exc 40mm on lime/sand stone all as specified and directed.

M&L for Raised pointing to RR masonry in CM 1:4 all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work block work stone work or concrete surfaces on walls in CM 1:4 finished even and smooth without using extra cement complete all as directed.

M & L for Preparation of new surfaces (Plastered or un-plastered) of walls or RCC Jaffries and applying two coats of cement base paint over a coat of primer complete all as specified.

M & L for preparation of old plasterd or unplastered surfaces of wall and applying two coat cement base paint complete all as specified and directed by Engr-in-Charge. Note (i) Before applying cement base paint contractor shall use the wire brush for the removal of loose paint, dust, algae, moss and filling of crack using crack sealent and cleaning of surface by spray jet. (ii) Application of cement base paint strictly done by spray/mechanical spray machine only, otherwise 30% cost recovery shall be made from the respective item. (iii) Filling of cracks, holes and dents are includes in the same rates.’ (iv) Proper curing with water to be done before and after application of 1st coat.

M&L for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

M&L for preparation of old steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

S & F for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

M & L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over 15mm thick cement plaster in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including demolition of existing granite or stone slabs of any type and position complete all as directed

M&L Machine pressed precast concrete rubber moulded interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grad with grey cement and pigments over & including 40mm sand cushion of approved design & pattern as approved by GE, complete all as specified and directed by Engr-in-Charge.

M & L 75mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone agg) as in sub base all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in kerbs slightly rounded or chamfered angles sides of path complete all as specified and diected.

M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments layed over 20mm thick cement screed base (1:6) and all as directed by Engr-in-charge.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified and as directed by Engr-in-Charge.

M&L Cement concrete (1:2:4) type C-2 using 20 mm graded stone aggregate as in floor, plinth protection, 100 mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as specified and directed by Engr-in-Charge.

Demolition of reinforced concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for

M & L for RCC Nominal Mix type B1 (1:2.4) using 20mm graded aggregate as in columns , piers posts and struts complete all as specified and directed.

M&L for RCC types B1 (1:2.4) (20mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for mild steel TMT bar 10mm dia and over cut to length, bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M & L for mild steel TMT bar 6 mm dia and over up to and including 10mm dia in stirrups, spacers and binders all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete square, rectangular or polygonal complete all as specified and directed.

M&L for form work to sides of column footings, plinth beams rough finished surfaces of concrete laid flat all as specified and directed.

Supply and fix concertina coil made to shape as dia exc 750 mm but not exc 1050 mm put on top of wall in between 'Y'shape angle iron post and secured with necessary binding wire all as specified and directed by Engr-in-charge.

S S ENTERPRISES

DARSHAN ENTERPRISES

JP ENTERPRISES

MAHESH DADAJI BACHHAV

SUNIL VEER CONSTRUCTION

S.R.M.K Enterprises

KARPE AND SONS CONSTRUCTION