Construction and commissioning of one number single story three bed room set insluated pre frefabricated and electrical works

Amount

Earth work in excavation by mechanical means (Hydraulic Excavator)/manual mans in foundaiton trenches or draing a9not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and dispoal of surplus excavatred sopild as directed, within a lead of 50m.

Excavating trenches of required width for pipes cables etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depthm, including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m: All kinds of soil Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foudnations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming ant watering, lead upto 50m nad lift upto 1.5m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:5:10 (1 cement:5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Provding and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement. All work up plinth level: 1:2:4 (1 cement : 2 coard sand : 4 graded stone aggregate 20 mm nominal size

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, plinth beams, et.c

Steel reinforcement for R.C.C. work including straightening, cutting bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Cement-sand Solid Readymade Blocks as locally available for Beams from RCC-foundation to foundations of height 450mm all around & as per requirement upto plinth level with Cement mortar:-Cement -sand solid blocks locally made with Cement mortar 1.6.(1 cement : 6 coarse sand) of mix 1:3:6 ( 1 cement :3 coarse sand : 6 stone agg. 20mm nominal size.

Structural steel work rived, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing mild round holding down bolts with nuts and providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Chequred precast cement tiles 22mm as per availibility on open verandah area of size;-3mtr-Length X 15mtr-width) foothpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20mm thick bed of cemnt mortar 1:4 (1 cement : 4 coarse sand) shade as per availibilty using ordinary cement

Providing and laying rectified Glazed ceramic floor & wall tiles of Size;-300x300mm x 8mm thick for toilets of 1st quality conforming to IS:15622, of approved make, in white colours fixed on floor with 20mm thick Cement Mortar. 1:4 (1 Cement:4 Coarse sand) & on walls with fixing adhesive etc. complete.

Providing and laying wooden floor tiles - 8mm thick in available sizes in wooden shade colours laid with foam sheet over existing Pcc floor complete. 8mm thick wooden floor tile of available size

Providing and Fixing 30mm thick false ceiling Puf panel with fixing accesories complete on false celing level for all heights as per specificaitons, drawings complete.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. Pan) with seat and lid. 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fitting and fixtures complete,including cuttiong and making good the walls and floors whereever required. W.C. Pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreious china flat back or wall corner type lipped front urinal basin of 30x260x350 mm and 340x410x265mm sizes respectively with automatic flushing cistern with sandard flush pipe and CP brass spereaders with brass unions ad GI clamps complete, inlucidng painting of fittings and brackets, cutting and making good hte walls and floor whereever equired: One urinal basi with 5 liter white P.V.C. automatic flushing cistern.

Providing and fixing was basin with CI brackets, 15 mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the wall wherever require. White Vitrious China Flat back wash basin size 550x400mm with single 5mmC.P brass pillar tap.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I brackets, CP brass waste of sandard patern and stainless steel plug 40mm including panting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without draing board 470x420mm bowl depth 178 mm

Providing and fixing P.V.C. waste pipe for sink or was basin including PVC waste fittings complete. Flexible pipe 32mm dia

40mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm hard board backing: Rectangular shape 453x357mm

Providing and fixing soil, waste and vent pipes: 100mm dia Centinfugally case (spun) iron socket & spigot (S&S) pipe as per IS:3989

Providing and fixing plain bend of required degree 10 mm dia Sand caste iron S&S as per IS:3989

Providing and fixing single equal junction of required degree: 100x100x100mm Sand cast iron S & S as per IS-3989

Providing lead caulked joints to sand cast iron/centrifugally cast(spun) iron pipes and fittings of diameter: 100mm dia

Providing and fixing trap of self cleanising design with screed down orhinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100mm inlet and 100mm outlets Sand cast iron S7 S as per iS:3989.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 10-5 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass scres with concealed fittings arrangemtn of approved quantity and colour 450mm long towel rail with total length of 495 mm 78mm wide and effective height of 88m, weighing not less than 170 gms.

Providing and fixing PTMT self 440mm long, 124 mm width and 36mm height of aproved quality and colour, wieghing not less than 300 gms.

Providing and fixing Cholrinated Polyvinyl Cholride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i/c fixing the pipe with clamps at 1.00 m spacing. This incldues jointing of pipes & fittings with one tep CPVC solvent cemnet and testing of joints complete as per direction of Engineer-in-charge. Internal work - Exposed on wall

Providing and placing (above toilet on steel frame supported) polyethlyene Loft water storage tank ISI : 127071 marked with cover and suitbale locking arrngemnt and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank-3Nos (each of 300Ltr Capacity).

Proviidng and fixing C.P. brass bib cock of aprpoved qualtiy conforming to IS:8931. 15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved qualtiy conforming to IS:8931. 15mm nominal bore

Providing and fixing PTMT Ball cock of approved qualtiy, colour and make compelte with Epoxy coated aluminium rod with high pressure H.D. plastic ball. 20mm nominal bore, 120mmlong, weighing not less than 198 gms

Providing and Fixing factory made UPVC - white colour door with frame. Frame : Frame made of Lead Free extruded UPVC sections, or minimum size 60mm x 65mm with minimum wall thickness 2.00 mm (+ 0.2mm), corners of the door frame shall be mitred cut and jointed with machine welding, including providing & fixing 3 nos. 3 D hinges to the frame and shutter, fixing the frame with jamb with reqruied number and sizes of dash fasteners of approved quality and inserting 2 number tie bar of 6 mm dia and fastening with nuts and washers at bottom and top of UPVC including making provision for all fittings and fixing at site and sealing and sealing of gaps as per the designs & specifications mentioned as per direction of engineers-in-charge, all complete to achieve smooth functioning of door and shutter.Shutter : Factory made UPVC door shutter with styles and rails including lock rail made of minimum 60mm x 95 mm size UPVC follow section and minimum wall thickness 2 mm (+ 0.2mm) with inbuilt bead on one side. Styles and rails shall be mitered cut and joint at thecorners by means of welding. All the sides i.e. style and rails shall be reinforced with GI channel profile of minimum size 32 x 14mm and minimum wall thicness 2mm (+ 0.2mm). Providing and fixing requried glass or PVC composite PUF Panel and uPVC snap fit beads co-extruded with EPDM gaskets, all of required size and section compatible with panel, all complete as per manufacturer's specification .HARDWARE : Using Espagnolette multipoint locking mechanism, suitable handle of minimum 100 mm size on both faces of door shutter and mortise lock of make and manufacture.INSTALLATION : The door shall be truly in plumb and water level and installed using steel fasteners with step-drill holes (13/8mm) in outer frames duly covered with fastener caps. The outer frame of door shall be sealed with silicone based Sealants from outside and acrylic paint-ble sealant from inside. Installtion shall be done by skilled workers supervised by Engineer-in-Charge.OTHER ARRANGEMENTS:The outer frame and shutter frame shall have provision for drainage, lock and key, all complete in the pattern as per directions of Engineer-in-charge.Rate and Measurements: Cost of the item includes supplying, installation and fixing of UPVC door, frame with all fittings & fixtures, locking arrangements, handles all complete as above inclusive of elements of labours, tools, lifting machines etc. cost of sealants, fasteners, screws, sleeves, spacers, protective tape, masking tape, bolts, gasket, fixtures, scaffolding complete in all respect and as per direction of Engineer-in-Charge. For calculating area of the door for payment, outer to outer dimentions of width and height of door frame shall be measured upto centimetre and area shall be calculated upto two places of decimels in square metre.Door with 24 mm thick PVC composite panels (Each Door of Size;- 2.2mtr -H X 1mtr-W)

Casement Windows with frame Iincluding 21mm DGU Toughened glass fixed- double shutters with 4mm frosted toughened glass

Ventilator type louvers(each of size;- 0.45mtr x 0.3mtr) made of 0.5mm TCT color coated PPGI Sheet for toilets, store & kithcen area complete. .

Providing and installing prefabricated Lloyd make Coutinuous line sandwich PUF Panel comprising of on two faces PPGL (galvalume) colour coated 0.5mm TCT sheet and CFC freeclose cell, high density rigid polyurethane foam of high density (40 + 2 kg/m3) having a thermal conductivity value of 0.023 w/mk and of required thickness sandwiched between the two galvalue sheets. The outer and inner galvalue sheet of 0.50 mm TCT steel 550 Mpa shall have a coating mass of 150 g/sqm zinc aluminium a alloy coating total of both sides as per AS-1397 and finished with 20 micron colour coating of SMP polyester wuality paint as per AS/NZS-2728:1997 (Category-3) over a 5 micron primer on exposed side and a back coat of 5 microns on inner side over a 5 micron primer. The panels should be of required length and requried width with maximum width upto 1190 mm with tongue & groove configuration.The prefabricated panels shall be fixed directly to the girth using self drilling fasteners. The metal sheet shall conform to IS:513.AS-1397 & 2728. the polyurethane insulation shall conform to IS:12436. The rate of the item is inclusive of all materials, erection accessories, incidental charges, cost of dash fasteners etc. and other incidental charges as per sample. For payment finished puf sand wich panel shall be measured upto half centimetres for calculating area upto two places of decimal. No deduction shall be made for opening upto 0.20 sqm. For Countinuos line Roof panels with 40 (40/80)mm thick Roofing panels having finished with 0.50mm thick TCT Galvalume Hi-rib shet on outer side and 0.50mm TCT Plain Galvalume sheet on inner side including miscellaneous expenses of fixing accessories such as fasteners etc. complete.

For Countinuous line wall panels for outer walls with 80mm thick wall panels finished with 0.50 mm thick TCT Galvalume Plain sheet with small ribs on both sides complete including miscellaneous expenses of fixing accessories such as fasteners etc, complete.

For Countinuous line internal partition wall panels for inner walls(upto False-Ceing Lvl.) with 80mm thick wall panels finished with 0.50 mm thick TCT Galvalume Plain sheet with small ribs on both sides with Camlock arrangement complete including miscellaneous expenses of fixing accessories such as fasteners etc, complete.

Supply & fixing of 12mm thick internal Cement Boards duly off-white color paint fininshed & joint filled with sealents/P.O.P/tape on existing internal partition puf panels walls with supporting steel frames complete.(Note ;-Partition wall puf panels & steel frame materials will be paid under respective items.)

Supply & Fixing flashings/ridges/U-Floor support channels etc. made in required shape/sizes of 0.50 mm thick TCT Galvalume Plain sheet complete including miscellaneous expenses of fixing accessories such as fasteners etc, complete

Supply & fixing of Internal Floor heating system (below wooden flooring system to be paid under seperate item) complete .

Subhead-I (Wiring, fitting and Electircal Panel) Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqm/mm FRLS PVC insulated copper conductor single core cable in surface/recessed pvc conduit, with modular switch, module plate, suitable GI box and earthing the point with 1..5 sq.mm . FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit /sub main wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed steel conduit as required. 2x1.5 sq.mm +1x1.5 sq.mm earth wire (For circuit wiring)

2 x6 sq.mm + 1.6 sq.mm earth wire (for Heater Outlets)

Wiring for light/power plug with 2x4sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit alongwith 1 No. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying, installatioon, testing and commissioning of 1200 long LED fitting with cover complete as required. (Make OSRAM/Philips/Bajaj/Equivalent)

Supplying and fixing of LED bulk head fittings suitable for 8-11 watt LED Lamp complte with accessories, etc. as reuqired. (Make Philips/OSRAM/Bajaj/Equivalent)

Supplying & fixing polycarbonate box alongwith 1 No. SPNMCB of 25 Amp i/c conneciton etc. complete as rquired (Make;-As per availibilty ofsize (200mm x 250mm)

Supplying, installation, testing and commissioning of cubical type wall mounted double door meter cum distribution b oard having window with Galls for energy meter suitble for 415V, 3 phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2mm thick for frame wirk and voers, 2mm thick for gland plates i/c cleaning and finishing complete iwth 7 tanks process for poweder coating in approved shade, having 150 Amp capacity TPIN Aluminium Alloy bus bars of high conductivity DMS/SMC bus bar supports, twih 2 Nos. earth stud, connections from main bus bar to switch gears with required size of copper wire and control wiring with 1.5sqm. mm PVC insulated FRLS copper conductor single core cable, cable alleys, cable gland plates in two half and providing and fixing following switch gears: (Minimum size of panel - 600mm x 800mm x 200mm) incoming 3 nos. Phase indicatioin LED lamps with 2 AMP back up MCB, breaker ON/OFF indicating light with 2A MCB 2A MCB. Outgoing: 25A SP MCB(10kA)-2 Nos 6/16A SP MCB (10kA) - 10 Nos.

Supplying and fixing brass batten/angle PVC bolders/including conection etc. as required (Anchor/cona/Kinjal)

Supplying and fixing call bell/buzzer suitable for single phase, 230 volts, complete as required. (Anchor/cona/Kinjal)

Earthing with GI earth pipe 4.5 meter long, 40 mm dia inclduing accessories and providiing masonry enclosure with cover plate having locking arrangemnt and watering pipe etc. with charcoal /coke and salt as requried.

Providing and laying earth connection earth electrode with 6 SWG dia GI wirehin 25mm dia G.I. pipe earth electrode including connection with G.I. thimble excavation and re-filling required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing alongwith existing surface/recessed conduit/sub main wireing/cable as required

Subhead - III (Fire Extinguisher) Supplying & fixing of following type ISI marked fire extinguisher including bracket etc. as required (Make: Lifeguard/safeguard/G Tech/Cease fire) 4.5 KG CO2 cylinder

6KG Dry Powder (ABC stores pressure)

SHUBHOM PREFABS AND ASSOCIATES