PROVN OF SPECIAL REPAIR TO BLDG No E-209 ( ACCN OFFICE, BN RATION STORE ETC OF ASC BN AT KANDHAR LINE , SPECIAL REPAIR TO DRAINAGE (1.5KM) WITH 05 SOAKAGE WELL INCLUDING COMPLETE DRAIN COVER AT RAPID (S) ENGR REGT AND ADDN /ALTERATION TO 04 COOK H

Amount

Taking down of wooden chowkhats or frame with shutters without taking off shutters from the frames n.exc 1.50 Sqm each complete all as specified & directed.

Taking down of chowkhats or frame with shutters without taking off shutters from the frames exc 1.50 Sqm & n exc 4.00 Sqm each complete all as specified & directed.

Supply & fix steel window box type using ERW 'P' section comprising double frame for gauged and glazed skeleton shutter jointed internally with flat iron 40x3mm all arround the complete frame including iron mongry etc complete including hinges, handle tower bolts stops, lugs etc complete all as specified and directed. . Note (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit .(ii)Unite rate quoted against this item shall also include the iron mongreries shown on drgs (iii) gaurd bars ,glazing & wire mesh shall be measured and paid for separately under respective item of BOQ

Supply and fix 30 mm thick flush shutters, solid core construction, with particle board core and plywood facepanels, commercial type on both sides, complete all as specified and directed.

Supply and fix galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including necessary beadings complete all as specified and directed.

Supply and fix 3 mm thick plain sheet glass ordinary quality and glazing with oil putty / beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

Supply & fixing framed work such as grills, granite or framed guard bars with end of bars shouldered or reveted or forged into spike, and similar articles conforming to Fe 410-0 or Fe 310-0 complete all as specified & directed.

Supply and fix butt hinges 100mm size, stainless steel medium weight , cold rolled incl necessary screws complete all as specified and directed.

Supply & fix 125mm size aluminium alloy handles, cast type, anodised complete all as specified and directed.

Supply & fix 150mm long aluminium anodized tower bolts of extruded section complete all as specified and directed.

Supply and fix 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix in repair 25 mm bore drapery curtain rods fancy type powder coated finished as directed including fixing brackets, stopes, roller etc complete all as specified and directed.

Demolition of plain cement concrete in ground floors & pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Material and labour 25mm thick cement concrete 1:2:4 type B-0 using (12.5 mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

Material and labour for coloured Non Skid ceramic tiles 7 to 8 mm thick, (square / rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and and directed

All as per item No 15.00 above but over and including 10mm thick rendering in CM 1:4 as in skirting/dado complete all as specified and directed.

Material and labour for PCC 1:3:6 type C1 (using 20mm graded aggregate) as in bed block , copings, kneelers, apex stones, bed plates, water troughs and the like including cutting into bricks of stone wal as srequired for inserting hold fast complete all as specfied and directed.

Material and labour for 75 mm thick PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) in path /plinth protection, finish cement concrete surface even & smooth without using extra cement complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation baords/slabs /blankets, any thickness, including cover fillets complete all as specified and directed.

Supply and fix false ceiling with 9mm thick E board white prelaminated , set embossed reinforced designer ceiling board of oceanic texture fixed over and including GI grid frame work of size not more than 600x600mm having 25mm wide t-section runner made of 0.33 mm GI sheet and angle made 0.45mm thick GI sheet suspended with and including 4mm dia GI wire and leveling clips inclding two coat of oil distemper complete all as specified and directed ( Note- All exposed surface of grid shall be powdered coated white).

Taking down of cement plaster of any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc complete all as specified & directed.

Material & labour for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry surfaces, finished even and smooth without using extra cement including WPC complete all as specified & directed. Note- WPC shall be measured and paid separately.

Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles incl removing rubbish off the premises complete all as specified and as directed.

Material and labour for brick work with fly ash bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

All as per item No 24.00 above but except bricks including cleaning of old bricks complete all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Supply and fix Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of a colour having tensile strength of 550 Mpa as in roof covering/claddingto wall, fixed with hot dip glavanised shelf drilling and shelf tapping screws neoprene and EPDM wahsers complete all as specified and directed.

Supply and fix Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of a colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Supply and fix mild steel flat iron as in wind ties including cutting drilling holes and securing bolts confirming to Fe-410 Gde-310 complete all as specified and directed.

Supply and fix second class hardwood as in plain solid straight chowkhats or frames, wrought, ragter, purlins and like truss work etc framed together with glue pinned at joints, with single or double rebates or as in perlins, rafters etc complete all as specified and directed.

Materials and labour for complete removal of existing treatment and finishing the surfaces of wall with wall putty and applying two coats of cement base paint of any colour, complete all as specified and directed by Engr-in-Charge.

Materials and labour for complete removal of existing treatment from wall and preparing the surfaces of wall by applying a coat of wall care putty and applying two coat of oil bound distemper of approved colour complete all as specified and directed.

Material and labour for preparation of newly plastered surface of wall etc and applying two coat of oil bound distemper (OBD ) over one coat of primer over and including 1mm thick wall care putty complete all as specified and directed.

Material and labour for preparation of newly plaster surface of wall and applying two coats of cement base paint over and including one coat of primer complete all as specified and directed.

Material and labour for preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour preparation of new or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer all as specified and directed.

Material and labour for plain cement concrete 1:3:6 type C-1 (20 mm graded crushed stone aggregate) as in surface channel and drains complete all as specified and directed.

Material and labour for forming fair finished drain or channel 60 cm inner girth in cmeent concrete usng extra cement, including forms, mould, mitred/stopped ends etc complete all as specified and directed.

Material and labour providing cement concrete 1:2:4 type B1 (20mm graded crushed stone aggregate) plain cement in coping to concrete block/brick masonry and for filling in road cutting and like etc complete all as specified and directed.

Material & labour for construction of Soakage wells, excavated. in ordinary soil, foundation PCC 1:3:6 walls of honey combed and solid brick in cement mortar ( 1:4), RCC slab in M25 design mix, filling work with brick bats, complete of size 3.00 m dia x 4.50m effective depth complete all as shown in TD Drg ( TD/309 sheet 1/4 to 4/4 of HQ CEBZ ) complete all as specified and directed.

Material and labour for precast cement concrete 1:2:4 type B-1 (20 mm graded crushed stone aggregate) as in manhole covers slabs set in cement mortar 1:4 including ncecessary form work and placing to disired distance complete all a specified and directed.

Material and labour for mild steel TMT bars 10mm dia and over, cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Material & labour for plain cement concrete bed to drain pipes including packing under, haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) for 300 mm bore pipe complete all as specified and directed.

Material and labour for bore pipe in 300 mm dia reinforced cocnrete pipes, class NP2 , laid and jointed include for laying pipes level or to falls in trenches, and tested, laind in trenches complete all as specified and directecd

Material and labour for for use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions to give rough finished flat surface of concrete complete all as specified and directed.

Material and Labour for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundation fillings and mass concrete including necessary form work complete all as specified and directed.

Material and labour for precast cement concrete solid block masonry 1:2:4 type B-1 using 20 mm graded crushed stone aggregate exc 10 cm in width and set in CM 1:6 omplete all as specified and directed

Material and labour for providing reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

Supply and fix rolled mild steel as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conf to Fe-410-W (Gde-E-250) quality 'A' complete all as specified and directed.

Supply and fix rolled mild steel plates (plain or chequered) square cut or notched (ordinary or counter sunk) forming holes confirming to Fe-410 W (Gde E250) quality A complete all as specified and directed.

Supply and fix 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc fixed with slef taping screws as specified and directed

Supply and fix expanded metal not exc 4 Kg, cut length, bent to shape required and welded to steel frame work supplied and fixed to steel members upto a height of 12mtr using necessary safety harness and equipments complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m in depth in soft/ loose soil for foundation n.exc 10 Sqm on plan, including levelling of bottom surface to required level getting out complete all as specified and directed.

Surface excavation in soft/loose soil n exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Removing excavated materials to a distance not exc 50 m and deposited where directed at a level not exc 1.5 m above the starting point all as specified and directed.

Material and labour for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base floor, finished even and rough to receive floor topping all as specified and directed.

Material and labour for 60mm thic PCC tile (interlocking type) with grey cement and pigment over and including 25 mm thick sand cushioning , interlocking tiles jointed filled wth sand and compacted with mechanical plate vibrator complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n.exc. 25cm thick in soft / loose soil complete all as specified and directed.

Taking down carefully any type of battens or conduit point wiring with or except conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed .

Material & labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FRLS PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories/fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal boxes including all cutting/chases etc in walls, making good to walls, ceiling etc including two coats of white/colour washing/distempering etc to the disturbed surfaces to match the existing with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for One Bulb /Tube light / bell point/security light controlled by one, one way switch 05 / 06 Amps.

All as per serial item No 60.00 above but for One ceilling fan/exhaust point controlled by one, one way switch 05 / 06 Amps.

All as per serial item No 60.00 above but for One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 60.00 above but for One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 60.00 above but with 2.5 Sqmm Nominal cross sectional area copper conductor cable for one 15/16 Amps socket outlet point on independent board.

Supply and fix switch piano flush type, 5/6 Amp single pole, one way 230 volts complete all as specified and directed.

Supply and fix socket outlet 3 pin, 05/06 Amp 230 volts complete all as specified and directed .

Supply and fix switch piano flush type, 15/16 Amp single pole, one way 230 volts complete all as specified and directed.

Supply and fix socket outlet 3 pin, 05/06 Amp and 3 pin 15/16 Amps (2 in 1 Multipurpose) 230 volts complete all as specified and directed .

Supply and fix stepped type electronic fan regulator flush AC, 230 volts, ISI marked with and including connector complete all as specified and directed .

Supply and fix decorative LED tube light fitting 1x20 Watt, with opal diffuser, environment friendly, energy efficient MS batten with retrofit T8 polycarbonate tube-01 No having single side connection complete with all accessories and fixing material complete all as specified and directed.

Supply and installed LED security light fitting 1x45 Watt luminaries , die cast aluminium housing comprising high power LEDs, enclosed with lens embedded PC cover with LED driver complete IP 65 protection including provision of 32 mm dia GI pipe light grade mounting bracklet,0.80 m long, bend to shape at 140 degree and fixed to wall with 02 Nos 40x 5mm Flat iron clamps . nuts, bolts and washer etc and including weather proof PVC insulated copper conductor cable size 23/0.0076 twisted of required length for making connection complete all as specified and directed.

Supply and fix LED lamp 9 Watt retrofit type suitable for batten holder 230 Volt single phase complete all as specified and directed.

Supply and fix lamp holder (Angular/Straight), insulated body, with back plate for batten fitting all as specified and directed.

Supply and fix of ceiling rose, 3 terminal PVC polycarbonate isolated body complete all as specified & directed .

Material and labour for sub main wiring with 2x6.00 Sqmm nominal cross sectional area (two single core cable of 6.00 Sqmm for phase and neutral + o1 single core cable of 6 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, FRLS unsheathed, copper conductor cable with and including continuous earth wire of size 6.00 Sqmm nominal cross sectional area, single core, PVC insulated, FRLS copper conductor cable drawing into rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories/fittings, brass screws, washers etc and connected to common earth dolly including taking down unserviceable sub main / service main wiring including all cutting/chases etc in wall, making good to walls etc including two coats of white/colour washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed. (Note : One meter of conduit along with 2x600 sqmm wire and one 6.00 sqmm earth wire shall be measured as one RM length.)

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amp rated copper bus bar and IP-43 protection with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer-in-Charge.

Supply and fixing MCB, SP, AC, 240 volts of 06 to 40 Amp B curve, 10 kA, complete all as specified and directed.

Supply and fixing MCB, SPN, AC, 240 volts of 40 Amp B curve, 10 kA, complete all as specified and directed.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed. (Note- After completion of work if desired result of earthing is not obtained the earthing shall be redone without any extra cost to Govt.)

Material and labour for laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 2.5 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches/ fixing on wall/ under road crossing through protection pipe etc including taking out old unserviceable LT cable complete all as specified and directed.

Supply/laying and fixing 40 mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

Material and labour for washed river dry sand cushioning in trenches 80mm thick before laying the cable and 150mm thick after laying the cable including spreading levelling and hard punning complete all as specified and directed.

Material and labour for contineous brick edging with width equal to the length of the brick of whole sub class 'B' bricks laid on edge for protection of cable complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n.exc. 25cm thick in soft / loose soil complete all as specified and directed.

AR Enterprises

Jay Ambay Enterprises