Special repair to Bldg no P-417 (08 qtrs) at Ajmer line of FOL depot ASC Jodhpur in Army Area Jodhpur

Amount

Demolition of cement concrete in ground floors and pavings n. exe 15 cm thickness (below or above ground level) complete all as specified & as directed.

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in flooring,path , sub foundation etc complete all as specified and directed.

M&L 50mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar places, without using extra cement complete all as specified and directed.

S&F machine made precast cement concrete blocks (interlocking paves) of 60mm thick with 6mm top layers of ante abrasive rubberised material laid over and including 25mm thick sand cushion . The interlocking joints shall be filled with fine sand . The compressive strength of layer shall not be less than 350 Kg/Cm2 complete all as specified and directed.

S&F machine made precast cement concrete curb stone blocks using Cement concrete 1:3:6 type C1 (20mm stone agg) all as directed by Engr-in-Charge.

Demolition of stone masonry built in cement mortar

M&L for squarred rubble walling Jodhpur type regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6 complete all as specified & directed.

All as per item No 7 above but except stone complate all as specified and directed.

M&L PCC solid building blocks 10 cm thick type B1 1:2:4 set in cement mortar (1:6) complete all as specified and directed.

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete all as specified and directed.

Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:4 over stone masonary surfaces incl finishing the surface fair & rough to receive tiling etc complete all as specified and directed.

M&L for glazed colour ceramic tiles of size 250x350x7mm/250x375x7mm, laid in vertical surface dado/skirting joint free etc, set and jointed in neat cement slurry and pointed in coloured tiles to match the shade of tiles complete all as specied and directed.

M&L for non-skid coloured ceremic tiles joint less 7 to 8 mm thick area of each tiles exceeding 0.18 Sqm but n.exc. 0.38 sqm in floor etc set jointed in neat cement slurry and pointed in white or coloured cement to match the shade.including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per Item no 14 above but skirting including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L non skid / mat finish ceramic colour tiles of size 300 mm x 300 mm and 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone slab flooring , over screed bed base ,laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing icluding 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone in riser of steps, skirting, dado and piller laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing including 10 mm thick rendering in cement mortor 1:6 complete all as specified and directed.

M & L of 15-18mm thick machine cut udaipur green marble as in land table work cooking plateform steps jamps including cement and jointedwith grey cement slurry with pigment to match the shade of the slab inclpolishing over and including complete all as specified.

M&L Rendering 5 mm thick CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface complete all as specified & directed.

Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar all as specified

M&L for Keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 all as specified.

M & L three coats of white wash on newly plastered surface of ceiling including preparation of surfaces complete all as specified and directed.

M&L preperartion of plastered surfaces on wall and applying one coat of wall putty with fair finished and even surface and applying two coat of oil bound distemper complete all as specified & directed.

M & L one coats of white wash on old surface of wall complete all as specified and directed..

M & L one coats of white wash on old surface of ceiling complete all as specified and directed.

Preparation of old plastered or un- plastered surfaces of wall by Brooming down or steel wire brushing, scrapping down mass and efflorescent salts and trading oil & greasy spots, washing rubbing down and stopping surfaces and applying one coat of cement base paint (swocem) of approved quality & tint complete all as specified and directed.

S&F magic eye brass body 15 to 20 mm dia all as per sample including drilling necessary hole in panel door shutter complete all as specified and as directed by engr-in-charge.

M & L applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces completeall as specified and directed.

Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

M & L for mild steel framed work as in brackets etc for coller stands etc framed steps/stairs etc complete using MS angle iron Steel bars gusset plate etc complete all as specified & directed .

Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

All as per item 36 above here-in-before but size 125x60mm with double rebate.

Demiolition of reinforced cement concrete of as staircase, landing, chajjas and similar suspended work of any description and any position not otherwise

M&L sand stone slabs in sunshades, chajjas, shelves, cills, landings cover stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness of slab 5cm complete

S&F mild steel frame work as in stairs ,hand rails half round or other stock section or section or core for wooden hand rail straidgt portion drilled and countershunk for balusters running bars for doors balusters nosing to steps including embeded in concrete and screwing etc hid ties for foof including securing bolts post and struts in fencing including securing bolts post and struts in fencing including cutting tops to shape as directed drilling holes nothing for wire etc flat iron fillet for necessary drilling boltinh or riveting etc and similar work confirming to Fe 410-0 or fe 310-0

Dismantling of boarding of any description and in any position complete all as specified.

M &L for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all specified and directed.

S & F 35mm thick factory made second class hardwood glazed and Skelton door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-1991 section 8 clause 8.24 (a) and as directed.

S&F Flush shutters 40 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specifid and directed by engr-in-charge.

S/F of 35mm thick factory made partly glazed and partly skeleton shutters, open rebated and prepared to receive wire gauze etc, edge of framing shall be plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc complete all as specified and directed.

S/F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted to the MS Frame/sealed to the stiles & rails with suitable PVC sheet beading, and joined 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted the MS Frame/sealed to the stiles & rail with suitable PVC sheet beading, and joined together with solvent cement, all as specified.

M/L for solid PVC door frame of size 50x47mm made out of 5mm thick pvc sheet reinforced with MS square tube all as specified.

Mild steel black sheet 1mm thick as in covering to door shutter cut to size, edges beaded if directed, hole punched incl round headed screws incl beading turning up metred angle, stopped ends etc complete all as specified and directed.

Taking down steel window/ventilator complete.

Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified (with or without cooler opening as directed by engr-in-charge). Refer Drg No CEJZ/TD/20 sheet1/3 to 3/3

Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified .(with or without cooler opening as directed by engr-in-charge). Refer Drg No CEJZ/TD/20 sheet1/3 to 3/3

Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified. Refer Drg No CEJZ/TD/20 sheet1/3 to 3/3

Factory made box type steel ventilator without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified. Refer Drg No CEJZ/TD/20 sheet1/3 to 3/3

Supply and fabrication of Mild steel guard bars and welded to window frames all as specified.

S/F of aluminium anodized,tower bolt 200 mm long complete all as specified and directed.

S&F aluminum anodised handle extruded section of size 150mm long complete all as specified and directed.

S/F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed.

S &F of mild steel butt hinges 100 mm size complete all as specified and directed.

S&F 100mm size single action door spring hinge complete all as specified and directed.

S & F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring 40mm long complete all as specified and directed.

S/F of 4 mm thick pinheaded sheet glass panes of size not. exceeding 0.5 Sqm fixed with oil putty complete all as specified and directed.

S/F for 3 mm thick plain glass ordinary quality & glazing complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm with necessary fitting on steel/ wooden surface complete all as specified and directed.

M/L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in hold fast iron fixing including necessary form work all as specified.

S&F in repair MS with PVC coated decorative 25mm curtain rod with fixing brackets, knob etc as in repairs complete all as specified and directed.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms)make prayag/polytuf

S&F in repair soap dish of PTMT fixed with screws complete all as specified and directed. Make prayag/polytuf

S&F in repair PTMT towel rail 450mm long fiexd to wall with chromium plated brass screws and woodn cleats Min weight 170gms approved make complete all as spcified and directed. Make ploytuf/prayag

S&F bath cabinet of PTMT fixed with and including chromium plated brass screws and wooden claeats size 355mmx455 . Make prayag/polytuf

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S & F in repair Stainless steel ,1.00mm thick for kitchen or laboratory with plug ,washers waste pipe , cast iron cantilever brackets connecting union overall size 495mmx420mm with bowl size 410mm x 330mmx160mm complete all as specified & directed.

S&F as in repairs of vitreous china clay water closet squatting pan ORISSA Pattern size 580x 440 mm white with integral foot rest incl 'P' or 'S' traps, flush pipe of 32mm dia HDPE pipe etc all as specified & directed.

S & F as in repairs vitreous china wash down water closet European Type pedestal pattern with seat & cover as in repairs with jet spray complete incl fixing of flush pipe etc complete all as specified and directed.

M/L Vitrous china wash basin as in repairs, white flat back size 550x400 mm including , waste fittings, waste pipe, MS brackets complete all as specified fixed in repair .

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore as directed

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore as directed

S&F of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in wall and fixed with MS clamp as per dierction of engineer in charge

S&F PVC SWR pipes single socketed in any length with rubber rings joints laid in trenches or in floors 110mm complete

S&F PVC SWR pipes single socketd in any length with rubber rings joints laid in trenches or in floors 75 mm complete

All as per item No 79 above but fixed in wall complete.

S&F of PVC SWR floor trap plain grating including jointing with solvent cement 75mm dia

S&F PVC (SWR) branch pieces single socketed Y equal or unequal 110mm

S&F PVC (SWR) bends any radius 110mm

S&F PVC (SWR) bends 75mm dia with oval acess door

S&F PVC SWR vent cowl 75mm

M&L (SWR) guly trap 125/110mm setting and jointing with solvent cement

S/F in repairs of chromium plated Swivel joint shower rose of 100 mm dia fixing with 15mm pipe. (Minimum weight 40gms) with Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.

supply & F fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm dia bore.

S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia all as specified specified.

S/F as in repairs fancy type , chromium plated anglular Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15 mm bore dia pipe.

S & F as in repairs 15 mm dia two way angular stop cock with chromium plated long thread with flange including flexiable chromium plated health faucet 1.5 mtr long complete all as specified and as directed.

S& F as in repairs 15 mm dia stop cock regular body with adujstable wall flange with chromium plated with (concealed type) all as specified

S/F as in repairs fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed to 15mm dia bore pipe

Supply & Fixing low level flusing cistern PVC 10 ltrs capacity with float valves (ISI Marked) white with inlet ball valve including float and includign pvc connection complete

Dismantling water tanks of capacity exc 250 ltrs but.nexc 500 ltrs and removing to store all as specified.

S&F rotational moulded polythene water storage tanks (cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part -I capacity of tank 500 ltrs capacity including tank led cover complete with fixing arrangement complete all as specified and directed.

S & F 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S& F in repair 750 X 600 X 200 mm, 1mm thick Stainless steel Plate Racks complete as directed.

S & F in repair 18 / 19 mm thick pre-laminated particle board exterior grade, pre-laminated one side with decorative choice of lamination and other side balancing white lamination as in cup board shutter fixed with screw teak wood beading all round / exposed faces complete.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised

S&F of 75 mm long Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws

S & F PVC cupboard knob fixed with nut , screw and washer of mild steel bright finished size exc. 25 mm dia but n. exc. 50 mm dia (as per sample) complete all as specified and directed.

M&L 50 thick PCC (1:2:4)Type B-1 using 20 mm graded stone aggregate for water tank plinth all as specified and directed.

S&F 75mm thick Jodhpur type stone slab not exc 2m in length dressed all face & along exposed edged size faced both sided as in drain cover.

Writing letters or figures (Black Roman, Italic or Indian n. exc 30cm high with thick paint complete all as specified

M & L for the rendering 5 mm thick on reinforced cement concrete surfaces in cement mortar (1:3) mixed with water proofing treatment compound at the rate of 3% by weight of cement complete all as directed.(WPC measured seperately)

M&L for treating the plastered surface (Sunken floor) with two coat of epoxy or water proofing adhesive coating complete all as specified by the manufacturers instruction and as directed by engineer in charge.(Make Pidilite, STP, IWL)

M&L for 75 mm thick plain cement concrete 1:2:4 type B 1 using 20 mm graded stone aggregates to use in sub base of floors of sunken portion laid in slope 1:40 to the surface of RCC slab shall be made even and smooth without using extra cement when concrete is still green complete all as directed by the E-in-Charge.

M&L for appling one coat of cold emulsion bitumenous primer @ 0.25 Kg/sqm shall applied on plastered surface including side walls. There after a layer of APP membrane 2.0 mm thick as specified above shall be laid by torch application method as per manufacturer instructions including cushion layer of coarse sand thickness 25 mm shall be provided to protect membrane.

M&L for PCC (1:5:10) lean cement concrete type E2 using 40 mm graded stone aggregate in mass concrete after carrying out satisfactory testing of CI pipe/ PVC pipe joints and slab /wall by filling water for 72 hours. Sunken portion of Nahani/ floor trap and pipe joints shall be embedded in PCC 1:3:6 type C1 complete.

S&F 32 mm bore light light grade galvanised steel water tubing provided 30 cm beyond wall surface to drain out leakage if any. The mouth of GI pipe shall have Gravel to avoided chocking. The top of sunken portio of RCC slab to be finished such that its slope towards spout.

Taking down or up steel tubing and connection including cleaning for refixing or removal (a) 20 mm dia

(b) All as per above but 15 mm dia

S/F of water tubing, medium grade, galvanized, with all fittings fixed to wall all as specified (a) 20 mm dia

(b) All as per above but 15 mm dia including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete.

Demolation of stone slabs laid dry but jointed & pointed in CM

Demolition of reinforced cement concrete of any description for roof,colums ,beam of any type etc complete all as specified and directed.

Use and waste of formwork to sides and soffits of slabs n. exc. 200 mm thick and similar works fair finished surfaces of concrete complete all as specified and directed.

Form work to edge of concrete flats, treads, breaks in floors, window cills, concrete railing, opening in concrete walls, floor and roofs n exc 20 cm wide and side of RCC/PCC bands in walls horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide with fair finished surfaces complere all as specified and directed.

Use and waste form work to sides and soffits of floor or roof beams, lintel, cantilevers, shelves etc. including support of fair finished surfaces complete.

M & L RCC design mix M-25 using 20 mm graded stone aggregate as in slab supported on wall, roof slab, chijja and in shelve etc complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix ) as in beam, cantilevers , bressummers, lintel overone meter span .

S & F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S & F mild steel TMT bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S & F mild steel TMT bar 5 dia and over upto and including 10 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M& L for roof treatment in the following stages :- (a) first Course : M&L for 10 mm thick plaster with CM 1:3 mixed with water proofing compound as per manufacturee instructions (Note: - WPC shall be measured and paid separately) (b) Second Course : One coat of bitumen primer T-10/polymerised confirming to IS 3384 @ 0.30 ltr/Sqm (c) Third Course : One coat of Bininding material using blown type bitumen conforming to IS 702 grade 85/25 @ 1.20 Kg/Sqm (d) Fourth Course : A layer of APP membrane polymeric membrane centre core of 100 micron HMHDPE outer film 20 micron each, thickness 2 mm having weigh 3.00Kg/Sqm (e) Fifth Course : A coat of bonding materail using blown type bitumn conforming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm (f) Sixth Course :40mm thick PCC 1:2:4 padding, well compacted using 20 mm graded aggreegatel with groovs shall not be exceeding 1.40 Sqm

Supply only Integral water proofing compound

M&L for PCC 1 : 2 : 4 Type B0 using 20 mm graded stone aggregate as in levelling course to the roof surface complete all as directed by Enginer-in-Charge.

Excavation in trenches for fdn n.exc 1.5m wide and n.exc 1.5m in depth & getting out in soft /loose soil

Returning filling in soil including spreading ,levelling,watering and well ramming in layers not exc 25cm thick

Removing excavated material not exceeding 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified.

M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for 150 mm dia pipe complete all as specified and directed.

Supply & laying jointing and testing 150mm bore reinfirced conctete pipes class NP-2 laid and jointed in cement mortor 1:1 complete with collars or socket/spigot type laid jointed and haunching at side in cement complete all as specified and directed.

Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket, ceiling rose etc complete

Point wiring complete with 1.5 sqmm, single core, multi stranded, copper conductor, PVC (FRLS), insulated, unsheathed cable, confirming to IS-694, 1100 volts grade, ISI marked (class V conductor), in and including PVC concealed conduit (MMS), ISI marked not less than 20mm, with accessories fixed on surface of wall/roof/ceiling etc and including sunken pressed steel terminal boxes in wall but including 3mm thick plastic laminated sheet top cover (ISI marked hylem sheet Make Anchor and 1.50 sqmm PVC insulated unsheathed stranded copper conductor for common earth and connecting to earth dolly material and labour for :- (a) One light point controlled by one, one way switch

(b) All as per item No 135 but One fan /Exhaust fan, point controlled by one way switch.

(c) All as per item No 135 but One socket outlet 3 pin 6 Amps on same board

(d) All as per item No 135 but One socket outlet 3 pin 6 Amp on independent board

(e) All as per item No 135 but One bell point controlled by one bell push.

All as per item No 135 above but with 2.5 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board .

S&F switch flush type single pole one way 6 Amp ISI Marked

S&F switch flush type single pole one way 16 Amp ISI Marked.

S&F only bell push , FT 6 Amp ISI Marked.

S&F bell AC 230V , SP , ISI Marked.

S&F socket out let , 5 pin , 6 Amp FT.

S&F socket out let , 3 pin ,16 Amp FT. ISI Marked

supply and fix socketed stepped type electonic fan regulator flush type , ISI Marked.

S & F Ceiling rose, 3 terminal/PVC/ polycarbonate, isolated body

S & F insulated Batton 9 watt LED lamp holder metal cased body of brass with back plate suitable for batton fittings including 9 watt LED Lamp.

Fixing only LED tube light fitting Box type 20 watt complete with all accessories such as bipin holders connector block, etc internally pre-wired , including LED lamp-1No, connectiong up with , multistranded copper conductor of size 1.00 sq mm flexible cable. Note : Item shall be issued under Sch 'B'.

S & F LED bulk head light 8/10 watt, including taking down u/s fitting any type

M/L in repairs sub main wiring with 6.00 Sq mm single core multistrandred copper conductor PVC insulated and unsheathed cable passing through PVC concealed conduit and making good the distrurbed surface of wall inc 6 Sq mm single core copper conductor cable PVC insulated and unsheathed cable as earth wire. Note :- Two runs of cable 6 Sqmm and One run of 6 Sqmm shall be measured as unit length.

S&F distribution board in sheet metal with 200 Amps rated copper bus bar Confirming to relevant IS.SPN 8 way, Note -Rate are deemed to be included for flashing in wall concealed complete, making good and matching existing surface.

S&F Prewired distribution board in sheet metal Prewired when MCB to be used with 200 Amps rated copper bus bar Confirming to relevant IS TPN 4 way, Make;-Legrand/ABB/Havell's Note -Rate are deemed to be included for flashing in wall concealed complete, making good and matching existing surface.

S&F MCB Single pole 5 to 30 Amp, 10 kA, ISI Marked.

S&F MCB SPN 63 Amp, 10 kA, ISI Marked.

S&F MCB TPN 63 Amp, 10 kA, ISI Marked.

Supply and lay cable XLPE insulated screened meter PVC bedded gal vanized steel strip or wire armored , electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16sq mm 4 core.Make: polycab./Havells/Finolex

Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no. 3 connected to Earthing test point all as specified or indicated including testing on completion Note : (i) Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover etc complete. (ii) Earth lead shall be up to 7.5 Mtr and rates are deemed to be included for GI pipe 15mm Light grade upto 7.5 mtrs for protection of earth wire 4.0 mm dia.

Taking down serviceable/Unserviceable , existing Electric Meter any Capacity and refixing the same position after minor repair complete the.

Shri Maruti Trading Co.

S. D. Construction Co.

M/s Vishnu Infrastructures

Nikhat nirman

KARNI CONSTRUCTION COMPANY

Harsh Enterprises

M/S JAGDAMBA ENTERPRISES